A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
Setting SERIO_QUIRK_NOMUX or SERIO_QUIRK_RESET_ALWAYS on the Clevo N150CU
and the Clevo NHxxRZQ makes the keyboard very laggy for ~5 seconds after
boot and sometimes also after resume. However both are required for the
keyboard to not fail completely sometimes after boot or resume.
The VT-d spec states (in section 11.4.2) that hardware implementations
reporting second-stage translation support (SSTS) field as Clear also
report the SAGAW field as 0. Fix an inappropriate check in alloc_iommu().
When commit commit fff1011a26d6 ("Input: xpad - add X-Box Adaptive Profile
button") was applied, one hunk ended up in the wrong function; move it to
where it belongs.
In case the driver was trying to set an alternate mode for gpio
0 or 32 then the mode was not set correctly. The reason is that
there is computation error inside the function ocelot_pinmux_set_mux
because in this case it was trying to shift to left by -1.
Fix this by actually shifting the function bits and not the position.
The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.
Fixes: 33fc42de3327 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.") Signed-off-by: Steffen Bätz <steffen@innosonix.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com> Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com> Fixes: 9dd441e4ed57 ("soc: qcom: ipa: GSI transactions") Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_card_ymfpci_remove() was removed in commit c6e6bb5eab74 ("ALSA:
ymfpci: Allocate resources with device-managed APIs"), but the call to
snd_card_new() was not replaced with snd_devm_card_new().
Since there was no longer a call to snd_card_free, unloading the module
would eventually result in Oops:
The code implicitly assumes that the list iterator finds a correct
handle. If 'vsi_handle' is not found the 'old_agg_vsi_info' was
pointing to an bogus memory location. For safety a separate list
iterator variable should be used to make the != NULL check on
'old_agg_vsi_info' correct under any circumstances.
Additionally Linus proposed to avoid any use of the list iterator
variable after the loop, in the attempt to move the list iterator
variable declaration into the macro to avoid any potential misuse after
the loop. Using it in a pointer comparison after the loop is undefined
behavior and should be omitted if possible [1].
Fixes: 37c592062b16 ("ice: remove the VSI info from previous agg") Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ Signed-off-by: Jakob Koschel <jkl820.git@gmail.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add profile conflict check while adding some FDIR rules to avoid
unexpected flow behavior, rules may have conflict including:
IPv4 <---> {IPv4_UDP, IPv4_TCP, IPv4_SCTP}
IPv6 <---> {IPv6_UDP, IPv6_TCP, IPv6_SCTP}
For example, when we create an FDIR rule for IPv4, this rule will work
on packets including IPv4, IPv4_UDP, IPv4_TCP and IPv4_SCTP. But if we
then create an FDIR rule for IPv4_UDP and then destroy it, the first
FDIR rule for IPv4 cannot work on pkt IPv4_UDP then.
To prevent this unexpected behavior, we add restriction in software
when creating FDIR rules by adding necessary profile conflict check.
The current implementation causes ice_vsi_update() to update all VSI
fields based on the cached VSI context. This also assumes that the
ICE_AQ_VSI_PROP_Q_OPT_VALID bit is set. This can cause problems if the
VSI context is not correctly synced by the driver. Fix this by only
updating the fields that correspond to ICE_AQ_VSI_PROP_Q_OPT_VALID.
Also, make sure to save the updated result in the cached VSI context
on success.
Fixes: 348048e724a0 ("ice: Implement iidc operations") Co-developed-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMSC911x doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 3ce9f2bef755 ("net: smsc911x: Stop and start PHY during suspend and resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230327083138.6044-1-wsa+renesas@sang-engineering.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In PPPoE add all IPv4 header option length to the parser
and adjust the L3 and L4 offset accordingly.
Currently the L4 match does not work with PPPoE and
all packets are matched as L3 IP4 OPT.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mvpp2 parser entry for QinQ has the inner and outer VLAN
in the wrong order.
Fix the problem by swapping them.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Reviewed-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
LOOP_CONFIGURE is, as far as I understand it, supposed to be a way to
combine LOOP_SET_FD and LOOP_SET_STATUS64 into a single syscall. When
using LOOP_SET_FD+LOOP_SET_STATUS64, a single uevent would be sent for
each partition found on the loop device after the second ioctl(), but
when using LOOP_CONFIGURE, no such uevent was being sent.
In the old setup, uevents are disabled for LOOP_SET_FD, but not for
LOOP_SET_STATUS64. This makes sense, as it prevents uevents being
sent for a partially configured device during LOOP_SET_FD - they're
only sent at the end of LOOP_SET_STATUS64. But for LOOP_CONFIGURE,
uevents were disabled for the entire operation, so that final
notification was never issued. To fix this, reduce the critical
section to exclude the loop_reread_partitions() call, which causes
the uevents to be issued, to after uevents are re-enabled, matching
the behaviour of the LOOP_SET_FD+LOOP_SET_STATUS64 combination.
I noticed this because Busybox's losetup program recently changed from
using LOOP_SET_FD+LOOP_SET_STATUS64 to LOOP_CONFIGURE, and this broke
my setup, for which I want a notification from the kernel any time a
new partition becomes available.
Signed-off-by: Alyssa Ross <hi@alyssa.is>
[hch: reduced the critical section] Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: 3448914e8cc5 ("loop: Add LOOP_CONFIGURE ioctl") Link: https://lore.kernel.org/r/20230320125430.55367-1-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
For ACPI drivers that provide a ->notify() callback and set
ACPI_DRIVER_ALL_NOTIFY_EVENTS in their flags, that callback can be
invoked while either the ->add() or the ->remove() callback is running
without any synchronization at the bus type level which is counter to
the common-sense expectation that notification handling should only be
enabled when the driver is actually bound to the device. As a result,
if the driver is not careful enough, it's ->notify() callback may crash
when it is invoked too early or too late [1].
This issue has been amplified by commit d6fb6ee1820c ("ACPI: bus: Drop
driver member of struct acpi_device") that made acpi_bus_notify() check
for the presence of the driver and its ->notify() callback directly
instead of using an extra driver pointer that was only set and cleared
by the bus type code, but it was present before that commit although
it was harder to reproduce then.
It can be addressed by using the observation that
acpi_device_install_notify_handler() can be modified to install the
handler for all types of events when ACPI_DRIVER_ALL_NOTIFY_EVENTS is
set in the driver flags, in which case acpi_bus_notify() will not need
to invoke the driver's ->notify() callback any more and that callback
will only be invoked after acpi_device_install_notify_handler() has run
and before acpi_device_remove_notify_handler() runs, which implies the
correct ordering with respect to the other ACPI driver callbacks.
Modify the code accordingly and while at it, drop two redundant local
variables from acpi_bus_notify() and turn its description comment into
a proper kerneldoc one.
Fixes: d6fb6ee1820c ("ACPI: bus: Drop driver member of struct acpi_device") Link: https://lore.kernel.org/linux-acpi/9f6cba7a8a57e5a687c934e8e406e28c.squirrel@mail.panix.com Reported-by: Pierre Asselin <pa@panix.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Pierre Asselin <pa@panix.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device release callback function invoked to release the matrix device
uses the dev_get_drvdata(device *dev) function to retrieve the
pointer to the vfio_matrix_dev object in order to free its storage. The
problem is, this object is not stored as drvdata with the device; since the
kfree function will accept a NULL pointer, the memory for the
vfio_matrix_dev object is never freed.
Since the device being released is contained within the vfio_matrix_dev
object, the container_of macro will be used to retrieve its pointer.
Fixes: 1fde573413b5 ("s390: vfio-ap: base implementation of VFIO AP device driver") Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Link: https://lore.kernel.org/r/20230320150447.34557-1-akrowiak@linux.ibm.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CPU: 1 PID: 5034 Comm: syz-executor350 Not tainted 6.2.0-rc6-syzkaller-80422-geda666ff2276 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
=====================================================
We can follow the call chain and find that 'bcm_tx_setup' function
calls 'memcpy_from_msg' to copy some content to the newly allocated
frame of 'op->frames'. After that the 'len' field of copied structure
being compared with some constant value (64 or 8). However, if
'memcpy_from_msg' returns an error, we will compare some uninitialized
memory. This triggers 'uninit-value' issue.
This patch will add 'memcpy_from_msg' possible errors processing to
avoid uninit-value issue.
For platforms with Alder Lake PCH (Alder Lake S and Raptor Lake S) the
slp_s0_residency attribute has been reporting the wrong value. Unlike other
platforms, ADL PCH does not have a counter for the time that the SLP_S0
signal was asserted. Instead, firmware uses the aggregate of the Low Power
Mode (LPM) substate counters as the S0ix value. Since the LPM counters run
at a different frequency, this lead to misreporting of the S0ix time.
Add a check for Alder Lake PCH and adjust the frequency accordingly when
display slp_s0_residency.
Fixes: bbab31101f44 ("platform/x86/intel: pmc/core: Add Alderlake support to pmc core driver") Signed-off-by: Rajvi Jingar <rajvi.jingar@linux.intel.com> Signed-off-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20230320212029.3154407-1-david.e.box@linux.intel.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit e0f9956a3862 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10fd ("net: stmmac: Add support for VLAN promiscuous mode") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The failover txq is inited as 16 queues.
when a packet is transmitted from the failover device firstly,
the failover device will select the queue which is returned from
the primary device if the primary device is UP and running.
If the primary device txq is bigger than the default 16,
it can lead to the following warning:
eth0 selects TX queue 18, but real number of TX queues is 16
Fix that by reducing txq number as the non-existent primary-dev does.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver") Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E") Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e6e ("net: dsa: microchip: update fdb add/del/dump in ksz_common") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba405b ("ptp_qoriq: fix NULL access if ptp dt node missing") Signed-off-by: SongJingyi <u201912584@hust.edu.cn> Reviewed-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
_base_allocate_sense_dma_pool() already prints out the sense pool
information, so don't print it a second time after calling it in
_base_allocate_memory_pools(). In addition the version in
_base_allocate_memory_pools() was using the wrong size value, sz, which was
last assigned when doing some nvme calculations instead of sense_sz to
determine the pool size in kilobytes.
Cc: Sathya Prakash <sathya.prakash@broadcom.com> Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Cc: MPT-FusionLinux.pdl@broadcom.com Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Fixes: 970ac2bb70e7 ("scsi: mpt3sas: Force sense buffer allocations to be within same 4 GB region") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20230324193204.567932-1-jsnitsel@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a physical disk is attached directly "without JBOD MAP support" (see
megasas_get_tm_devhandle()) then there is no real error handling in the
driver. Return FAILED instead of SUCCESS.
Fixes: 18365b138508 ("megaraid_sas: Task management support") Signed-off-by: Tomas Henzl <thenzl@redhat.com> Link: https://lore.kernel.org/r/20230324150134.14696-1-thenzl@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At NIC reset, some offload features related to encapsulated traffic
might have changed (this mainly happens if the firmware-variant is
changed with the sfboot userspace tool). Because of this, features are
checked and set again at reset time.
However, this was not done right, and some features were improperly
overwritten at NIC reset:
- Tunneled IPv6 segmentation was always disabled
- Features disabled with ethtool were reenabled
- Features that becomes unsupported after the reset were not disabled
Also, checking if the device supports IPV6_CSUM to enable TSO6 is no
longer necessary because all currently supported devices support it.
Additionally, move the assignment of some other features to the
EF10_OFFLOAD_FEATURES macro, like it is done in ef100, leaving the
selection of features in efx_pci_probe_post_io a bit cleaner.
Fixes: ffffd2454a7a ("sfc: correctly advertise tunneled IPv6 segmentation") Fixes: 24b2c3751aa3 ("sfc: advertise encapsulated offloads on EF10") Reported-by: Tianhao Zhao <tizhao@redhat.com> Suggested-by: Jonathan Cooper <jonathan.s.cooper@amd.com> Tested-by: Jonathan Cooper <jonathan.s.cooper@amd.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20230323083417.7345-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NFS server Duplicate Request Cache (DRC) algorithms rely on NFS clients
reconnecting using the same local TCP port. Unique NFS operations are
identified by the per-TCP connection set of XIDs. This prevents file
corruption when non-idempotent NFS operations are retried.
Currently, NFS client TCP connections are using different local TCP ports
when reconnecting to NFS servers.
After an NFS server initiates shutdown of the TCP connection, the NFS
client's TCP socket is set to NULL after the socket state has reached
TCP_LAST_ACK(9). When reconnecting, the new socket attempts to reuse
the same local port but fails with EADDRNOTAVAIL (99). This forces the
socket to use a different local TCP port to reconnect to the remote NFS
server.
State Transition and Events:
TCP_CLOSE_WAIT(8)
TCP_LAST_ACK(9)
connect(fail EADDRNOTAVAIL(99))
TCP_CLOSE(7)
bind on new port
connect success
dmesg excerpts showing reconnect switching from TCP local port of 926 to
763 after commit 7c81e6a9d75b:
[13354.947854] NFS call mkdir testW
...
[13405.654781] RPC: xs_tcp_state_change client 00000000037d0f03...
[13405.654813] RPC: state 8 conn 1 dead 0 zapped 1 sk_shutdown 1
[13405.654826] RPC: xs_data_ready...
[13405.654892] RPC: xs_tcp_state_change client 00000000037d0f03...
[13405.654895] RPC: state 9 conn 0 dead 0 zapped 1 sk_shutdown 3
[13405.654899] RPC: xs_tcp_state_change client 00000000037d0f03...
[13405.654900] RPC: state 9 conn 0 dead 0 zapped 1 sk_shutdown 3
[13405.654950] RPC: xs_connect scheduled xprt 00000000037d0f03
[13405.654975] RPC: xs_bind 0.0.0.0:926: ok (0)
[13405.654980] RPC: worker connecting xprt 00000000037d0f03 via tcp
to 10.101.6.228 (port 2049)
[13405.654991] RPC: 00000000037d0f03 connect status 99 connected 0
sock state 7
[13405.655001] RPC: xs_tcp_state_change client 00000000037d0f03...
[13405.655002] RPC: state 7 conn 0 dead 0 zapped 1 sk_shutdown 3
[13405.655024] RPC: xs_connect scheduled xprt 00000000037d0f03
[13405.655038] RPC: xs_bind 0.0.0.0:763: ok (0)
[13405.655041] RPC: worker connecting xprt 00000000037d0f03 via tcp
to 10.101.6.228 (port 2049)
[13405.655065] RPC: 00000000037d0f03 connect status 115 connected 0
sock state 2
State Transition and Events with patch applied:
TCP_CLOSE_WAIT(8)
TCP_LAST_ACK(9)
TCP_CLOSE(7)
connect(reuse of port succeeds)
dmesg excerpts showing reconnect on same TCP local port of 936 with patch
applied:
[ 257.139935] NFS: mkdir(0:59/560857152), testQ
[ 257.139937] NFS call mkdir testQ
...
[ 307.822702] RPC: state 8 conn 1 dead 0 zapped 1 sk_shutdown 1
[ 307.822714] RPC: xs_data_ready...
[ 307.822817] RPC: xs_tcp_state_change client 00000000ce702f14...
[ 307.822821] RPC: state 9 conn 0 dead 0 zapped 1 sk_shutdown 3
[ 307.822825] RPC: xs_tcp_state_change client 00000000ce702f14...
[ 307.822826] RPC: state 9 conn 0 dead 0 zapped 1 sk_shutdown 3
[ 307.823606] RPC: xs_tcp_state_change client 00000000ce702f14...
[ 307.823609] RPC: state 7 conn 0 dead 0 zapped 1 sk_shutdown 3
[ 307.823629] RPC: xs_tcp_state_change client 00000000ce702f14...
[ 307.823632] RPC: state 7 conn 0 dead 0 zapped 1 sk_shutdown 3
[ 307.823676] RPC: xs_connect scheduled xprt 00000000ce702f14
[ 307.823704] RPC: xs_bind 0.0.0.0:936: ok (0)
[ 307.823709] RPC: worker connecting xprt 00000000ce702f14 via tcp
to 10.101.1.30 (port 2049)
[ 307.823748] RPC: 00000000ce702f14 connect status 115 connected 0
sock state 2
...
[ 314.916193] RPC: state 7 conn 0 dead 0 zapped 1 sk_shutdown 3
[ 314.916251] RPC: xs_connect scheduled xprt 00000000ce702f14
[ 314.916282] RPC: xs_bind 0.0.0.0:936: ok (0)
[ 314.916292] RPC: worker connecting xprt 00000000ce702f14 via tcp
to 10.101.1.30 (port 2049)
[ 314.916342] RPC: 00000000ce702f14 connect status 115 connected 0
sock state 2
Fixes: 7c81e6a9d75b ("SUNRPC: Tweak TCP socket shutdown in the RPC client") Signed-off-by: Siddharth Rajendra Kawar <sikawar@microsoft.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'info_buf' memory is cached and driver polls ECC bit in it. This bit
is set by the NAND controller. If 'usleep_range()' returns before device
sets this bit, 'info_buf' will be cached and driver won't see update of
this bit and will loop forever.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller") Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/d4ef0bd6-816e-f6fa-9385-f05f775f0ae2@sberdevices.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
In fwnode_for_each_child_node(), we should add
fwnode_handle_put() when break out of the iteration
fwnode_for_each_child_node() as it will automatically
increase and decrease the refcounter.
Fixes: fc622b3d36e6 ("platform/surface: Set up Surface Aggregator device registry") Signed-off-by: Liang He <windhl@126.com> Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20230322033057.1855741-1-windhl@126.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ThinkStation platforms don't support the API to return possible_values
but instead embed it in the settings string.
Try and extract this information and set the possible_values attribute
appropriately.
Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms") Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230320003221.561750-4-mpearson-lenovo@squebb.ca Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some attributes don't have any values available. In those cases don't
make the possible_values entry visible.
Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms") Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230320003221.561750-3-mpearson-lenovo@squebb.ca Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
firmware-attributes class requires that possible values are delimited
using ';' but the Lenovo firmware uses ',' instead.
Parse string and replace where appropriate.
Suggested-by: Thomas Weißschuh <linux@weissschuh.net> Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms") Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230320003221.561750-2-mpearson-lenovo@squebb.ca Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms") Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230320003221.561750-1-mpearson-lenovo@squebb.ca Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If CDM_CHECK is enabled (by the DT "snps,enable-cdm-check" property), 'val'
is overwritten by PCIE_PL_CHK_REG_CONTROL_STATUS initialization. Commit ec7b952f453c ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check"
exists") did not account for further usage of 'val', so we wrote improper
values to PCIE_PORT_LINK_CONTROL when the CDM check is enabled.
Move the PCIE_PORT_LINK_CONTROL update to be completely after the
PCIE_PL_CHK_REG_CONTROL_STATUS register initialization.
The recent support of low latency playback in USB-audio driver made
the snd_usb_queue_pending_output_urbs() function to be called via PCM
ack ops. In the new code path, the function is performed already in
the PCM stream lock. The problem is that, when an XRUN is detected,
the function calls snd_pcm_xrun() to notify, but snd_pcm_xrun() is
supposed to be called only outside the stream lock. As a result, it
leads to a deadlock of PCM stream locking.
For avoiding such a recursive locking, this patch adds an additional
check to the code paths in PCM core that call the ack callback; now it
checks the error code from the callback, and if it's -EPIPE, the XRUN
is handled in the PCM core side gracefully. Along with it, the
USB-audio driver code is changed to follow that, i.e. -EPIPE is
returned instead of the explicit snd_pcm_xrun() call when the function
is performed already in the stream lock.
Because the bootloader (CFE) is not initializing the Read-ahead cache properly
on the second thread (TP1). Since the RAC was not initialized properly, we
should avoid flushing it at the risk of corrupting the instruction stream as
seen in the trace above.
In case when VCPU is blocked due to WFI, we schedule the timer
from `kvm_riscv_vcpu_timer_blocking()` to keep timer interrupt
ticking.
But in case when delta_ns comes to be zero, we never schedule
the timer and VCPU keeps sleeping indefinitely until any activity
is done with VM console.
This is easily reproduce-able using kvmtool.
./lkvm-static run -c1 --console virtio -p "earlycon root=/dev/vda" \
-k ./Image -d rootfs.ext4
Also, just add a print in kvm_riscv_vcpu_vstimer_expired() to
check the interrupt delivery and run `top` or similar auto-upating
cmd from guest. Within sometime one can notice that print from
timer expiry routine stops and the `top` cmd output will stop
updating.
This change fixes this by making sure we schedule the timer even
with delta_ns being zero to bring the VCPU out of sleep immediately.
wait_for_completion_timeout() and readl_poll_timeout() don't handle their
return value the same way.
wait_for_completion_timeout() returns 0 on time out (and >0 in all other
cases)
readl_poll_timeout() returns 0 on success and -ETIMEDOUT upon a timeout.
In order for the error handling path to work in both cases, the logic
against wait_for_completion_timeout() needs to be inverted.
This structure must be zeroed, because it's field 'hw->core' is used as
'parent' in 'clk_core_fill_parent_index()', but it will be uninitialized.
This happens, because when this struct is not zeroed, pointer 'hw' is
"initialized" by garbage, which is valid pointer, but points to some
garbage. So 'hw' will be dereferenced, but 'core' contains some random
data which will be interpreted as a pointer. The following backtrace is
result of dereference of such pointer:
everywhere in here. This is makes the lines longer than they need to
be, and will be especially noticeable when we add the active tracking in,
so add a temp variable for the space_info so this is cleaner.
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
reclaim isn't set in the alloc case, however we only care about
reclaim in the !alloc case. This isn't an actual problem, however
-Wmaybe-uninitialized will complain, so initialize reclaim to quiet the
compiler.
Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: df384da5a49c ("btrfs: use temporary variable for space_info in btrfs_update_block_group") Signed-off-by: Sasha Levin <sashal@kernel.org>
Overwriting the error code with the deletion result may cause the
function to return 0 despite encountering an error. Commit b111545d26c0
("tracing: Remove the useless value assignment in
test_create_synth_event()") solves a similar issue by
returning the original error code, so this patch does the same.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-trace-kernel/20230131075818.5322-1-aagusev@ispras.ru Signed-off-by: Anton Gusev <aagusev@ispras.ru> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
var->pixclock can be assigned to zero by user. Without
proper check, divide by zero would occur when invoking
macro PICOS2KHZ in au1200fb_fb_check_var.
Variable var->pixclock is controlled by user and can be assigned
to zero. Without proper check, divide by zero would occur in
intelfbhw_validate_mode and intelfbhw_mode_to_hw.
variable var->pixclock can be set by user. In case it
equals to zero, divide by zero would occur in nvidiafb_set_par.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to nvidia_check_var and nvidiafb_set_par. We believe it
could also be triggered in driver nvidia from user site.
XSK redirecting XDP programs require linearity, hence applies
restrictions on the MTU. For PAGE_SIZE=4K, MTU shouldn't exceed 3498.
Features that contradict with XDP such HW-LRO and HW-GRO are enforced
by the driver in advance, during XSK params validation, except for MTU,
which was not enforced before this patch.
This has been spotted during test scenario described below:
Attaching xdpsock program (PAGE_SIZE=4K), with MTU < 3498, detaching
XDP program, changing the MTU to arbitrary value in the range
[3499, 3754], attaching XDP program again, which ended up with failure
since MTU is > 3498.
This commit lowers the XSK MTU limitation to be aligned with XDP MTU
limitation, since XSK socket is meaningless without XDP program.
The getaffinity() system call uses 'cpumask_size()' to decide how big
the CPU mask is - so far so good. It is indeed the allocation size of a
cpumask.
But the code also assumes that the whole allocation is initialized
without actually doing so itself. That's wrong, because we might have
fixed-size allocations (making copying and clearing more efficient), but
not all of it is then necessarily used if 'nr_cpu_ids' is smaller.
Having checked other users of 'cpumask_size()', they all seem to be ok,
either using it purely for the allocation size, or explicitly zeroing
the cpumask before using the size in bytes to copy it.
See for example the ublk_ctrl_get_queue_affinity() function that uses
the proper 'zalloc_cpumask_var()' to make sure that the whole mask is
cleared, whether the storage is on the stack or if it was an external
allocation.
Fix this by just zeroing the allocation before using it. Do the same
for the compat version of sched_getaffinity(), which had the same logic.
Also, for consistency, make sched_getaffinity() use 'cpumask_bits()' to
access the bits. For a cpumask_var_t, it ends up being a pointer to the
same data either way, but it's just a good idea to treat it like you
would a 'cpumask_t'. The compat case already did that.
The user provides arbitrary non-numeic value to level and type,
which could bring unexpected behavior. In this case the expected
behavior would be to throw an error.
fb_set_var would by called when user invokes ioctl with cmd
FBIOPUT_VSCREENINFO. User-provided data would finally reach
tgafb_check_var. In case var->pixclock is assigned to zero,
divide by zero would occur when checking whether reciprocal
of var->pixclock is too high.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to tgafb_check_var. We believe it could also be triggered
in driver tgafb from user site.
sound/pci/hda/patch_ca0132.c:4229:2: note: After for loop, i has value 12
for (i = 0; i < TUNING_CTLS_COUNT; i++)
^
sound/pci/hda/patch_ca0132.c:4234:43: note: Array index out of bounds
dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
^
This patch cares non match case.
Therefore, We will get too many warning via cppcheck, like below
sound/pci/asihpi/hpi6205.c:238:27: warning: Possible null pointer dereference: pao [nullPointer]
struct hpi_hw_obj *phw = pao->priv;
^
sound/pci/asihpi/hpi6205.c:433:13: note: Calling function '_HPI_6205', 1st argument 'NULL' value is 0
_HPI_6205(NULL, phm, phr);
^
sound/pci/asihpi/hpi6205.c:401:20: note: Calling function 'control_message', 1st argument 'pao' value is 0
control_message(pao, phm, phr);
^
Set phr->error like many functions doing, and don't call _HPI_6205()
with NULL.
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
kgd_mem pointers returned by kfd_process_device_translate_handle are
only guaranteed to be valid while p->mutex is held. As soon as the mutex
is unlocked, another thread can free the BO.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
svm_migrate_ram_to_vram migrates a prange from sys ram to vram. The prange may
cross multiple vma. Need remember current dst vram offset in the TTM resource for
each migration.
v2: squash in warning fix (Alex)
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A new platform-op was added to Xen to allow obtaining the same VGA
console information PV Dom0 is handed. Invoke the new function and have
the output data processed by xen_init_vga().
slot_store() uses kstrtouint() to get a slot number, but stores the
result in an "int" variable (by casting a pointer).
This can result in a negative slot number if the unsigned int value is
very large.
A negative number means that the slot is empty, but setting a negative
slot number this way will not remove the device from the array. I don't
think this is a serious problem, but it could cause confusion and it is
best to fix it.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Recent firmware changes modified the curve duration from 32 to 64 bits,
which breaks volume ramps. A simple solution would be to change the
definition, but unfortunately the ASoC topology framework only supports
up to 32 bit tokens.
This patch suggests breaking the 64 bit value in low and high parts, with
only the low-part extracted from topology and high-part only zeroes. Since
the curve duration is represented in hundred of nanoseconds, we can still
represent a 400s ramp, which is just fine. The defacto ABI change has no
effect on existing users since the IPC4 firmware has not been released just
yet.
Link: https://github.com/thesofproject/linux/issues/4026 Signed-off-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20230307110656.1816-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic for the ioremap is to find the resource index 3 (IRAM) and
infer the BAR address by subtracting the IRAM offset. The BAR size
defined in hardware specifications is 2MB.
The commit 5947b2726beb6 ("ASoC: SOF: Intel: Check the bar size before
remapping") tried to find the BAR size by querying the resource length
instead of a pre-canned value, but by requesting the size for index 3
it only gets the size of the IRAM. That's obviously wrong and prevents
the probe from proceeding.
This commit attempted to fix an issue in a fuzzing/simulated
environment but created another on actual devices, so the best course
of action is to revert that change.
Reported-by: Ferry Toth <fntoth@gmail.com> Tested-by: Ferry Toth <fntoth@gmail.com> (Intel Edison-Arduino) Link: https://github.com/thesofproject/linux/issues/3901 Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20230307095341.3222-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sof_ipc3_rx_msg() checks for minimum size of a new rx message but it is
missing the check for upper limit.
Corrupted or compromised firmware might be able to take advantage of this
to cause out of bounds reads outside of the message area.
Reported-by: Curtis Malainey <cujomalainey@chromium.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Curtis Malainey <curtis@malainey.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20230307114917.5124-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sometimes the system boots up with a acpi_video0 backlight interface
which doesn't work. So add Dell Vostro 15 3535 into the
video_detect_dmi_table to set it to native explicitly.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
assert(x) should emit a warning if x is false. WARN_ON(x) emits a
warning if x is true. Thus, assert(x) should be defined as WARN_ON(!x)
rather than WARN_ON(x).
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Nick Terrell <terrelln@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When copying data to user-space we should ensure that only valid
data is copied over. Padding in structures may be filled with
random (possibly sensitve) data and should never be given directly
to user-space.
This patch fixes the copying of xfrm algorithms and the encap
template in xfrm_user so that padding is zeroed.
The PE/COFF header has a NX compat flag which informs the firmware that
the application does not rely on memory regions being mapped with both
executable and writable permissions at the same time.
This is typically used by the firmware to decide whether it can set the
NX attribute on all allocations it returns, but going forward, it may be
used to enforce a policy that only permits applications with the NX flag
set to be loaded to begin wiht in some configurations, e.g., when Secure
Boot is in effect.
Even though the arm64 version of the EFI stub may relocate the kernel
before executing it, it always did so after disabling the MMU, and so we
were always in line with what the NX compat flag conveys, we just never
bothered to set it.
The blamed commit changed struct ocelot_stat_layout :: "u32 offset" to
"u32 reg".
However, "u32 reg" is not quite a register address, but an enum
ocelot_reg, which in itself encodes an enum ocelot_target target in the
upper bits, and an index into the ocelot->map[target][] array in the
lower bits.
So, whereas the previous code comparison between stats_layout[i].offset
and last + 1 was correct (because those "offsets" at the time were
32-bit relative addresses), the new code, comparing layout[i].reg to
last + 4 is not correct, because the "reg" here is an enum/index, not an
actual register address.
What we want to compare are indeed register addresses, but to do that,
we need to actually go through the same motions as
__ocelot_bulk_read_ix() itself.
With this bug, all statistics counters are deemed by
ocelot_prepare_stats_regions() as constituting their own region.
(Truncated) log on VSC9959 (Felix) below (prints added by me):
Before:
region of 1 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x001]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x002]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x041]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x042]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x081]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x0ac]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x100]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x101]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x111]
After:
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
Since commit d87b1c08f38a ("net: mscc: ocelot: use bulk reads for
stats") intended bulking as a performance improvement, and since now,
with trivial-sized regions, performance is even worse than without
bulking at all, this could easily qualify as a performance regression.
Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Colin Foster <colin.foster@in-advantage.com> Tested-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add .percent suffix option to show the histogram values in percentage.
This feature is useful when we need yo undersntand the overall trend
for the histograms of large values.
E.g. this shows the runtime percentage for each tasks.
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
At sc7280, pingpong block is used to management the dither effects
to reduce distortion at panel. Currently pingpong-0 base offset is
wrongly set at 0x59000. This mistake will not cause system to crash.
However it will make dither not work. This patch correct sc7280 ping
pong-0 block base offset.
Changes in v2:
-- add more details info n regrading of pingpong block at commit text
projects / users / jedix / linux-maple.git / log