The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.
There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: d38499530e5 ("fs: decouple READ and WRITE from the block layer ops") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the kernel must run in the memory chunk with the lowest address,
ST-RAM is ignored, and removed from the m68k_memory[] array.
However, it is not removed from memblock, causing a crash later.
More investigation shows that there are 3 places where memory chunks are
ignored, all after the calls to memblock_add() in m68k_parse_bootinfo(),
and thus causing crashes:
1. On classic m68k CPUs with a MMU, paging_init() ignores all memory
chunks below the first chunk, cfr. above,
2. On Amigas equipped with a Zorro III bus, config_amiga() ignores all
Zorro II memory,
3. If CONFIG_SINGLE_MEMORY_CHUNK=y, m68k_parse_bootinfo() ignores all
but the first memory chunk.
Fix this by moving the calls to memblock_add() from
m68k_parse_bootinfo() to paging_init(), after all ignored memory chunks
have been removed from m68k_memory[].
Reported-by: Andreas Schwab <schwab@linux-m68k.org> Fixes: 1008a11590b966b4 ("m68k: switch to MEMBLOCK + NO_BOOTMEM") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the same reason as commit 25896d073d8a ("x86/build: Fix compiler
support check for CONFIG_RETPOLINE"), you cannot put this $(error ...)
into the parse stage of the top Makefile.
Perhaps I'd propose a more sophisticated solution later, but this is
the best I can do for now.
Link: https://lkml.org/lkml/2017/12/25/211 Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reported-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Reported-by: Qian Cai <cai@lca.pw> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Qian Cai <cai@lca.pw> Signed-off-by: Sasha Levin <sashal@kernel.org>
mac80211 uses the frag list to build AMSDU. When freeing
the skb, it may not be really freed, since someone is still
holding a reference to it.
In that case, when TCP skb is being retransmitted, the
pointer to the frag list is being reused, while the data
in there is no longer valid.
Since we will never get frag list from the network stack,
as mac80211 doesn't advertise the capability, we can safely
free and nullify it before releasing the SKB.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd52 ("vxge: serialize access to steering control register") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea80 ("net/macb: change RX path for GEM") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08b6 ("net: macb: Add 64 bit addressing support for GEM") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Acked-by: Harini Katakam <harini.katakam@xilinx.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a21598a ("qed: No need for LL2 frags indication") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52eca5 ("mac80211: Run TXQ teardown code before de-registering interfaces") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.
The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.
So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting from mac80211 commit adf8ed01e4fd ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f05 ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
rbnode in insert_tree() is rcu protected pointer.
So, in order to handle this pointer, _rcu function should be used.
rb_link_node_rcu() is a rcu version of rb_link_node().
The dst entry might already have a zero refcount, waiting on rcu list
to be free'd. Using dst_hold() transitions its reference count to 1, and
next dst release will try to free it again -- resulting in a double free:
In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.
Fixes: 45040978c899 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel") Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad633 ("ixgbe: fix driver behaviour after issuing VFLR") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca0c ("i40e: don't remove netdev->dev_addr when syncing uc list") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a guard hole at the beginning of the kernel address space, also
used by hypervisors. It occupies 16 PGD entries.
This reserved range is not defined explicitely, it is calculated relative
to other entities: direct mapping and user space ranges.
The calculation got broken by recent changes of the kernel memory layout:
LDT remap range is now mapped before direct mapping and makes the
calculation invalid.
The breakage leads to crash on Xen dom0 boot[1].
Define the reserved range explicitely. It's part of kernel ABI (hypervisors
expect it to be stable) and must not depend on changes in the rest of
kernel memory layout.
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
ibmvnic_reset allocated new reset work item objects in a non-atomic
context. This can be called from a tasklet, generating the output below.
Allocate work items with the GFP_ATOMIC flag instead.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before commit 7fd6d98b89f3 ("i2c: i801: Allow ACPI AML access I/O
ports not reserved for SMBus"), enabling RMI on the T560 would cause
the touchpad to stop working after resuming from suspend. Now that
this issue is fixed, RMI can be enabled safely and works fine.
With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.
From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.
Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.
Fixes: aea71a024914 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.
This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.
basechain->stats is rcu protected data which is updated from
nft_chain_stats_replace(). This function is executed from the commit
phase which holds the pernet nf_tables commit mutex - not the global
nfnetlink subsystem mutex.
Test commands to reproduce the problem are:
%iptables-nft -I INPUT
%iptables-nft -Z
%iptables-nft -Z
This patch uses RCU calls to handle basechain->stats updates to fix a
splat that looks like:
This patch fixes a off-by-one mistake in nla_parse_nested() functions of
mac802154_hwsim driver. I had to enabled stack protector so I was able
to reproduce it.
Since commit 222d7dbd258d ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code doesn't expect this to happen, so we crash with
a NULL pointer dereference in this case.
Fix it by checking skb_dst(skb) for NULL after skb_dst_force()
and drop the packet in case the dst_entry was cleared. We also
move the skb_dst_force() to a codepath that is not used when
the transformation was offloaded, because in this case we
don't have a dst_entry attached to the skb.
The output and forwarding path was already fixed by
commit 9e1437937807 ("xfrm: Fix NULL pointer dereference when
skb_dst_force clears the dst_entry.")
xfrm_output_one() does not return a error code when there is
no dst_entry attached to the skb, it is still possible crash
with a NULL pointer dereference in xfrm_output_resume(). Fix
it by return error code -EHOSTUNREACH.
Right now, checkstack.pl isn't able to print anything on aarch64,
because it won't be able to match the stating objdump line of a function
due to this missing space. Hence, it displays every stack as zero-size.
After this patch, checkpatch.pl is able to match the start of a
function's objdump, and is then able to calculate each function's stack
correctly.
Link: http://lkml.kernel.org/r/20181207195843.38528-1-cai@lca.pw Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for bonding of RoCE devices was added, there was
necessarily a link between the RoCE device and the paired netdevice that
was part of the bond. If you remove the mlx4_en module, that paired
association is broken (the RoCE device is still present but the paired
netdevice has been released). We need to account for this in
is_upper_ndev_bond_master_filter() and filter out those links with a
broken pairing or else we later oops in netdev_next_upper_dev_rcu().
If CS is submitted using guilty ctx, we terminate amdgpu_cs_parser_init
before locking ctx->lock, latter in amdgpu_cs_parser_fini we still are
trying to release the lock just becase parser->ctx != NULL.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "altmap" is used to provide a pool of memory that is reserved for
the vmemmap backing of hot-plugged memory. This is useful when adding
large amount of ZONE_DEVICE memory to a system with a limited amount of
normal memory.
On ppc64 we use huge pages to map the vmemmap which requires the backing
storage to be contigious and aligned to the hugepage size. The altmap
implementation allows for the altmap provider to reserve a few PFNs at
the start of the range for it's own uses and when this occurs the
first chunk of the altmap is not usable for hugepage mappings. On hash
there is no sane way to fall back to a normal sized page mapping so we
fail the allocation. This results in memory hotplug failing with
ENOMEM when the new range doesn't fall into an existing vmemmap block.
This patch handles this case by falling back to using system memory
rather than failing if we cannot allocate from the altmap. This
fallback should only ever be used for the first vmemmap block so it
should not cause excess memory consumption.
Fixes: 7b73d978a5d0 ("mm: pass the vmem_altmap to vmemmap_populate") Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
The 258a:6a88 keyboard-dock shipped with the Prowise PT301 tablet is
likely another ITE based design. The controller die is directly bonded
to the PCB with a blob of black glue on top so there are no markings and
the 258a vendor-id used is unknown anywhere. But the keyboard has the
exact same hotkeys mapped to Fn+F1 - F10 as the other ITE8595 keyboard
I have *and* it has the same quirky behavior wrt the rfkill hotkey.
Either way as said this keyboard has the same quirk for its rfkill /
airplane mode hotkey as the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds the 258a:6a88 USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/powerpc/mm/dump_linuxpagetables.c: In function 'populate_markers':
arch/powerpc/mm/dump_linuxpagetables.c:306:39: error: 'PKMAP_BASE' undeclared (first use in this function)
arch/powerpc/mm/dump_linuxpagetables.c:314:50: error: 'LAST_PKMAP' undeclared (first use in this function)
These come from highmem.h, including that fixes the build.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper
as a relocatable ET_DYN", 2011-04-12) changed the procedure descriptor
at the start of crt0.S to have a hard-coded start address of 0x500000
rather than a reference to _zimage_start, presumably because having
a reference to a symbol introduced a relocation which is awkward to
handle in a position-independent executable. Unfortunately, what is
at 0x500000 in the COFF image is not the first instruction, but the
procedure descriptor itself, that is, a word containing 0x500000,
which is not a valid instruction. Hence, booting a COFF zImage
results in a "DEFAULT CATCH!, code=FFF00700" message from Open
Firmware.
This fixes the problem by (a) putting the procedure descriptor in the
data section and (b) adding a branch to _zimage_start as the first
instruction in the program.
Fixes: 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper as a relocatable ET_DYN") Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Since commit d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
MIPS' asm/mmzone.h includes the machine/platform mmzone.h
unconditionally, but since commit bb53fdf395ee ("MIPS: c-r4k: Add
r4k_blast_scache_node for Loongson-3") is included by asm/rk4cache.h for
all r4k-style configs regardless of CONFIG_NEED_MULTIPLE_NODES.
This is problematic when CONFIG_NEED_MULTIPLE_NODES=n because both the
loongson3 & ip27 mmzone.h headers unconditionally define the NODE_DATA
preprocessor macro which is aready defined by linux/mmzone.h, resulting
in the following build error:
In file included from ./arch/mips/include/asm/mmzone.h:10,
from ./arch/mips/include/asm/r4kcache.h:23,
from arch/mips/mm/c-r4k.c:33:
./arch/mips/include/asm/mach-loongson64/mmzone.h:48: error: "NODE_DATA" redefined [-Werror]
#define NODE_DATA(n) (&__node_data[(n)]->pglist)
In file included from ./include/linux/topology.h:32,
from ./include/linux/irq.h:19,
from ./include/asm-generic/hardirq.h:13,
from ./arch/mips/include/asm/hardirq.h:16,
from ./include/linux/hardirq.h:9,
from arch/mips/mm/c-r4k.c:11:
./include/linux/mmzone.h:907: note: this is the location of the previous definition
#define NODE_DATA(nid) (&contig_page_data)
Resolve this by only including the machine mmzone.h when
CONFIG_NEED_MULTIPLE_NODES=y, which also removes the need for the empty
mach-generic version of the header which we delete.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: bb53fdf395ee ("MIPS: c-r4k: Add r4k_blast_scache_node for Loongson-3") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e82b0b382845 ("spi: bcm2835: Fix race on DMA termination") broke
the build with COMPILE_TEST=y on arches whose cmpxchg() requires 32-bit
operands (xtensa, older arm ISAs).
Fix by changing the dma_pending flag's type from bool to unsigned int.
Fixes: e82b0b382845 ("spi: bcm2835: Fix race on DMA termination") Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tpm_i2c_nuvoton calculated commands duration using TPM 1.x
values via tpm_calc_ordinal_duration() also for TPM 2.x chips.
Call tpm2_calc_ordinal_duration() for retrieving ordinal
duration for TPM 2.X chips.
First, rename out_no_locality to out_locality for bailing out on
both tpm_cmd_ready() and tpm_request_locality() failure.
Second, ignore the return value of go_to_idle() as it may override
the return value of the actual tpm operation, the go_to_idle() error
will be caught on any consequent command.
Last, fix the wrong 'goto out', that jumped back instead of forward.
Cc: stable@vger.kernel.org Fixes: 627448e85c76 ("tpm: separate cmd_ready/go_idle from runtime_pm") Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM Linux kernel handles the EABI syscall numbers as follows:
0 - NR_SYSCALLS-1 : Invoke syscall via syscall table
NR_SYSCALLS - 0xeffff : -ENOSYS (to be allocated in future)
0xf0000 - 0xf07ff : Private syscall or -ENOSYS if not allocated
> 0xf07ff : SIGILL
Our compat code gets this wrong and ends up sending SIGILL in response
to all syscalls greater than NR_SYSCALLS which have a value greater
than 0x7ff in the bottom 16 bits.
Fix this by defining the end of the ARM private syscall region and
checking the syscall number against that directly. Update the comment
while we're at it.
Cc: <stable@vger.kernel.org> Cc: Dave Martin <Dave.Martin@arm.com> Reported-by: Pi-Hsun Shih <pihsun@chromium.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we insert the sync sequence number into the CMD_SYNC.MSIData field,
we do so in CPU-native byte order, before writing out the whole command
as explicitly little-endian dwords. Thus on big-endian systems, the SMMU
will receive and write back a byteswapped version of sync_nr, which would
be perfect if it were targeting a similarly-little-endian ITS, but since
it's actually writing back to memory being polled by the CPUs, they're
going to end up seeing the wrong thing.
Since the SMMU doesn't care what the MSIData actually contains, the
minimal-overhead solution is to simply add an extra byteswap initially,
such that it then writes back the big-endian format directly.
Cc: <stable@vger.kernel.org> Fixes: 37de98f8f1cf ("iommu/arm-smmu-v3: Use CMD_SYNC completion MSI") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the nospec API, it should be taken into account that:
"...if the CPU speculates past the bounds check then
* array_index_nospec() will clamp the index within the range of [0,
* size)."
The above is part of the header for macro array_index_nospec() in
linux/nospec.h
Now, in this particular case, if intid evaluates to exactly VGIC_MAX_SPI
or to exaclty VGIC_MAX_PRIVATE, the array_index_nospec() macro ends up
returning VGIC_MAX_SPI - 1 or VGIC_MAX_PRIVATE - 1 respectively, instead
of VGIC_MAX_SPI or VGIC_MAX_PRIVATE, which, based on the original logic:
/* SGIs and PPIs */
if (intid <= VGIC_MAX_PRIVATE)
return &vcpu->arch.vgic_cpu.private_irqs[intid];
Fix this by calling array_index_nospec() macro with VGIC_MAX_PRIVATE + 1
and VGIC_MAX_SPI + 1 as arguments for its parameter size.
Fixes: 41b87599c743 ("KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_get_irq()") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[dropped the SPI part which was fixed separately] Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When restoring the active state from userspace, we don't know which CPU
was the source for the active state, and this is not architecturally
exposed in any of the register state.
Set the active_source to 0 in this case. In the future, we can expand
on this and exposse the information as additional information to
userspace for GICv2 if anyone cares.
Cc: stable@vger.kernel.org Signed-off-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To change the active state of an MMIO, halt is requested for all vcpus of
the affected guest before modifying the IRQ state. This is done by calling
cond_resched_lock() in vgic_mmio_change_active(). However interrupts are
disabled at this point and we cannot reschedule a vcpu.
We actually don't need any of this, as kvm_arm_halt_guest ensures that
all the other vcpus are out of the guest. Let's just drop that useless
code.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Suggested-by: Christoffer Dall <christoffer.dall@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c3e ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726eb ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
We currently only halt the guest when a vCPU messes with the active
state of an SPI. This is perfectly fine for GICv2, but isn't enough
for GICv3, where all vCPUs can access the state of any other vCPU.
Let's broaden the condition to include any GICv3 interrupt that
has an active state (i.e. all but LPIs).
Cc: stable@vger.kernel.org Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although bit 31 of VTCR_EL2 is RES1, we inadvertently end up setting all
of the upper 32 bits to 1 as well because we define VTCR_EL2_RES1 as
signed, which is sign-extended when assigning to kvm->arch.vtcr.
Lucky for us, the architecture currently treats these upper bits as RES0
so, whilst we've been naughty, we haven't set fire to anything yet.
Cc: <stable@vger.kernel.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When passing a large read to receive_encrypted_read(), ensure that the
demultiplex_thread knows that a MID was processed. Without this, those
operations never complete.
This is a similar issue/fix to lease break handling:
commit 7af929d6d05ba5564139718e30d5bc96bdbc716a
("smb3: fix lease break problem introduced by compounding")
CC: Stable <stable@vger.kernel.org> # 4.19+ Fixes: b24df3e30cbf ("cifs: update receive_encrypted_standard to handle compounded responses") Signed-off-by: Paul Aurich <paul@darkrain42.org> Tested-by: Yves-Alexis Perez <corsac@corsac.net> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While resolving a bug with locks on samba shares found a strange behavior.
When a file locked by one node and we trying to lock it from another node
it fail with errno 5 (EIO) but in that case errno must be set to
(EACCES | EAGAIN).
This isn't happening when we try to lock file second time on same node.
In this case it returns EACCES as expected.
Also this issue not reproduces when we use SMB1 protocol (vers=1.0 in
mount options).
Further investigation showed that the mapping from status_to_posix_error
is different for SMB1 and SMB2+ implementations.
For SMB1 mapping is [NT_STATUS_LOCK_NOT_GRANTED to ERRlock]
(See fs/cifs/netmisc.c line 66)
but for SMB2+ mapping is [STATUS_LOCK_NOT_GRANTED to -EIO]
(see fs/cifs/smb2maperror.c line 383)
Quick changes in SMB2+ mapping from EIO to EACCES has fixed issue.
Signed-off-by: Georgy A Bystrenin <gkot@altlinux.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4936084c2ee2 ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
introduce a mistake in atomic64_fetch_##op##_relaxed(), because it
forget to delete R10000_LLSC_WAR in the if-condition. So fix it.
Commit 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx
interface detection") added RGMII interface detection for OCTEON III,
but it results in the following logs:
[ 7.165984] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
[ 7.173017] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
The current RGMII routines are valid only for older OCTEONS that
use GMX/ASX hardware blocks. On later chips AGL should be used,
but support for that is missing in the mainline. Until that is added,
mark the interface as disabled.
Fixes: 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx interface detection") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # 4.7+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASIDs have always been stored as unsigned longs, ie. 32 bits on MIPS32
kernels. This is problematic because it is feasible for the ASID version
to overflow & wrap around to zero.
We currently attempt to handle this overflow by simply setting the ASID
version to 1, using asid_first_version(), but we make no attempt to
account for the fact that there may be mm_structs with stale ASIDs that
have versions which we now reuse due to the overflow & wrap around.
Encountering this requires that:
1) A struct mm_struct X is active on CPU A using ASID (V,n).
2) That mm is not used on CPU A for the length of time that it takes
for CPU A's asid_cache to overflow & wrap around to the same
version V that the mm had in step 1. During this time tasks using
the mm could either be sleeping or only scheduled on other CPUs.
3) Some other mm Y becomes active on CPU A and is allocated the same
ASID (V,n).
4) mm X now becomes active on CPU A again, and now incorrectly has the
same ASID as mm Y.
Where struct mm_struct ASIDs are represented above in the format
(version, EntryHi.ASID), and on a typical MIPS32 system version will be
24 bits wide & EntryHi.ASID will be 8 bits wide.
The length of time required in step 2 is highly dependent upon the CPU &
workload, but for a hypothetical 2GHz CPU running a workload which
generates a new ASID every 10000 cycles this period is around 248 days.
Due to this long period of time & the fact that tasks need to be
scheduled in just the right (or wrong, depending upon your inclination)
way, this is obviously a difficult bug to encounter but it's entirely
possible as evidenced by reports.
In order to fix this, simply extend ASIDs to 64 bits even on MIPS32
builds. This will extend the period of time required for the
hypothetical system above to encounter the problem from 28 days to
around 3 trillion years, which feels safely outside of the realms of
possibility.
The cost of this is slightly more generated code in some commonly
executed paths, but this is pretty minimal:
I have been unable to measure any change in performance of the LMbench
lat_ctx or lat_proc tests resulting from the 64b ASIDs on either
32r2el_defconfig+interAptiv or 32r6el_defconfig+I6500 systems.
Signed-off-by: Paul Burton <paul.burton@mips.com> Suggested-by: James Hogan <jhogan@kernel.org>
References: https://lore.kernel.org/linux-mips/80B78A8B8FEE6145A87579E8435D78C30205D5F3@fzex.ruijie.com.cn/
References: https://lore.kernel.org/linux-mips/1488684260-18867-1-git-send-email-jiwei.sun@windriver.com/ Cc: Jiwei Sun <jiwei.sun@windriver.com> Cc: Yu Huabing <yhb@ruijie.com.cn> Cc: stable@vger.kernel.org # 2.6.12+ Cc: linux-mips@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KEXEC needs the new kernel's load address to be aligned on a page
boundary (see sanity_check_segment_list()), but on MIPS the default
vmlinuz load address is only explicitly aligned to 16 bytes.
Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase
the alignment calculated by calc_vmlinuz_load_addr to 64KB.
For multi-node Loongson-3 (NUMA configuration), r4k_blast_scache() can
only flush Node-0's scache. So we add r4k_blast_scache_node() by using
(CAC_BASE | (node_id << NODE_ADDRSPACE_SHIFT)) instead of CKSEG0 as the
start address.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paul.burton@mips.com: Include asm/mmzone.h from asm/r4kcache.h for
nid_to_addrbase(). Add asm/mach-generic/mmzone.h
to allow inclusion for all platforms.] Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21129/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <james.hogan@mips.com> Cc: Steven J . Hill <Steven.Hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: <stable@vger.kernel.org> # 3.15+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions") Cc: stable@vger.kernel.org # v4.8+ Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Rich Felker <dalias@libc.org> Cc: David Daney <david.daney@cavium.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case that a bprintk event has a dereferenced pointer that is
stored as a string, and there's more values to process (more args), the
arg was not updated to point to the next arg after processing the
dereferenced pointer, and it screwed up what was to be displayed.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Fixes: 37db96bb49629 ("tools lib traceevent: Handle new pointer processing of bprint strings") Link: http://lkml.kernel.org/r/20181210134522.3f71e2ca@gandalf.local.home Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vb2_core_create_bufs did not check if the memory model for newly added
buffers is the same as for already existing buffers. It should return an
error if they aren't the same.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: syzbot+e1fb118a2ebb88031d21@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> # for v4.16 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log