James Bottomley [Tue, 27 Mar 2018 16:27:34 +0000 (12:27 -0400)]
Merge branch 'fixes' into misc
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Adrian Hunter [Tue, 20 Mar 2018 13:07:38 +0000 (15:07 +0200)]
scsi: ufs: Add support for Auto-Hibernate Idle Timer
UFS host controllers may support an autonomous power management feature
called the Auto-Hibernate Idle Timer. The timer is set to the number of
microseconds of idle time before the UFS host controller will autonomously
put the link into Hibernate state. That will save power at the expense of
increased latency. Any access to the host controller interface registers
will automatically put the link out of Hibernate state. So once configured,
the feature is transparent to the driver.
Expose the Auto-Hibernate Idle Timer value via SysFS to allow users to
choose between power efficiency or lower latency. Set a default value of
150 ms.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanislav Nijnikov [Thu, 1 Mar 2018 10:48:06 +0000 (12:48 +0200)]
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
Read from these files will return the integer value of the chosen power
management level now. Separate entries were added to show the target UFS
device and UIC link states. The description of the possible power
managements levels was added to the ABI file. The on-write behaviour of
these entries wasn't changed.
[mkp: typo]
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Meelis Roos [Thu, 8 Mar 2018 13:44:37 +0000 (15:44 +0200)]
scsi: qla2xxx: fx00 copypaste typo
Fix an obvious copy-paste error in freeing QLAFX00 response queue - the
code checked for rsp->ring but freed rsp->ring_fx00.
[mkp: applied by hand]
Signed-off-by: Meelis Roos <mroos@linux.ee> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Meelis Roos [Thu, 8 Mar 2018 13:44:07 +0000 (15:44 +0200)]
scsi: qla2xxx: fix error message on <qla2400
This patch fixes IO traps caught by hardware when mailbox command fails
on qla2200. The error handler assumes newer firmware that is available
on 2400 and newer HBA-s.
This causes ugly crashes on sparc64.
Fix it with separate debug prints on different firmware generations like
most other places do.
[mkp: updated based on feedback from Himanshu]
Signed-off-by: Meelis Roos <mroos@linux.ee> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Wed, 21 Mar 2018 18:32:37 +0000 (13:32 -0500)]
scsi: smartpqi: update driver version
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Gerry Morong <gerry.morong@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 21 Mar 2018 18:32:31 +0000 (13:32 -0500)]
scsi: smartpqi: workaround fw bug for oq deletion
Skip deleting PQI operational queues when there is an error creating a
new queue group. It's not really necessary to delete the queues anyway
because they get deleted during the PQI reset that is part of the error
recovery path.
Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
himanshu.madhani@cavium.com [Wed, 21 Mar 2018 06:09:41 +0000 (23:09 -0700)]
scsi: qla2xxx: Update driver version to 10.00.00.06-k
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:39 +0000 (23:09 -0700)]
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
This patch cleans up ABTS handling for FC-NVMe by
- Removing allocation of sp, instead pass the sp pointer for abort IOCB
- Fix error handling from Trasport failure
- set outstanding_cmds array to NULL for nvme completion
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:38 +0000 (23:09 -0700)]
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:37 +0000 (23:09 -0700)]
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:36 +0000 (23:09 -0700)]
scsi: qla2xxx: Remove nvme_done_list
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:35 +0000 (23:09 -0700)]
scsi: qla2xxx: Return busy if rport going away
This patch adds mechanism to return EBUSY if rport is going away
to prevent exhausting FC-NVMe layer's retry counter.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:34 +0000 (23:09 -0700)]
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
On a port db changes, this patch will set n2n_ae flag for N2N
connection when requesting for Report ID Acquition MBX, instead
of Loop Initialization or point to point asynchronous events.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:33 +0000 (23:09 -0700)]
scsi: qla2xxx: Add FC-NVMe abort processing
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:32 +0000 (23:09 -0700)]
scsi: qla2xxx: Add changes for devloss timeout in driver
Add support for error recovery within devloss timeout, now that
FC-NVMe transport support devloss timeout.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:31 +0000 (23:09 -0700)]
scsi: qla2xxx: Set IIDMA and fcport state before qla_nvme_register_remote()
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
himanshu.madhani@cavium.com [Wed, 21 Mar 2018 06:09:30 +0000 (23:09 -0700)]
scsi: qla2xxx: Remove unneeded message and minor cleanup for FC-NVMe
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 21 Mar 2018 06:09:29 +0000 (23:09 -0700)]
scsi: qla2xxx: Restore ZIO threshold setting
Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: devinfo: remove dasd devices from the scsi subsystem
Only present through ccw bus.
[mkp: applied by hand]
Cc: Matthias Rudolph <Matthias.Rudolph@hitachivantara.com> Cc: Takahiro Yasui <takahiro.yasui@hitachivantara.com> Cc: Anthony Cheung <anthony.cheung@hpe.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Cc: s390 ML <linux-s390@vger.kernel.org> Cc: SCSI ML <linux-scsi@vger.kernel.org> Cc: device-mapper development <dm-devel@redhat.com> Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthias did confirm that there are no such devices.
[mkp: applied by hand]
Cc: Matthias Rudolph <Matthias.Rudolph@hitachivantara.com> Cc: Anthony Cheung <anthony.cheung@hpe.com> Cc: Takahiro Yasui <takahiro.yasui@hitachivantara.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Cc: SCSI ML <linux-scsi@vger.kernel.org> Cc: device-mapper development <dm-devel@redhat.com> Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: devinfo: add HP DISK-SUBSYSTEM device, for HP XP arrays
"The DISK-SUBSYSTEM is a special model name returned when LUs
are not installed. For example, when LU#0 is not installed in "OPEN-"
models, LU#0 is detected as the DISK-SUBSYSTEM model":
https://marc.info/?l=linux-scsi&m=125424006417825
Geert Uytterhoeven [Fri, 16 Mar 2018 13:51:50 +0000 (14:51 +0100)]
scsi: hisi_sas: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In
most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Mark Brown <broonie@kernel.org> Acked-by: Robin Murphy <robin.murphy@arm.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Mon, 19 Mar 2018 10:33:03 +0000 (13:33 +0300)]
scsi: dpt_i2o: use after free in adpt_release()
The scsi_host_put() function frees "pHba" and then we dereference it on
the next line when we do "scsi_host_put(pHba->host);".
[mkp: included fix from hch]
Fixes: 38e09e3bb056 ("scsi: dpt_i2o: stop using scsi_unregister") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jianchao Wang [Wed, 7 Mar 2018 12:29:03 +0000 (20:29 +0800)]
scsi: iscsi_tcp: set BDI_CAP_STABLE_WRITES when data digest enabled
iscsi tcp will first send out data, then calculate and send data
digest. If we don't have BDI_CAP_STABLE_WRITES, the page cache will be
written in spite of the on going writeback. Consequently, wrong digest
will be got and sent to target.
To fix this, set BDI_CAP_STABLE_WRITES when data digest is enabled
in iscsi_tcp .slave_configure callback.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Acked-by: Chris Leech <cleech@redhat.com> Acked-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin K. Petersen [Wed, 14 Mar 2018 16:15:56 +0000 (12:15 -0400)]
scsi: sd: Remember that READ CAPACITY(16) succeeded
The USB storage glue sets the try_rc_10_first flag in an attempt to
avoid wedging poorly implemented legacy USB devices.
If the device capacity is too large to be expressed in the provided
response buffer field of READ CAPACITY(10), a well-behaved device will
set the reported capacity to 0xFFFFFFFF. We will then attempt to issue a
READ CAPACITY(16) to obtain the real capacity.
Since this part of the discovery logic is not covered by the first_scan
flag, a warning will be printed a couple of times times per revalidate
attempt if we upgrade from READ CAPACITY(10) to READ CAPACITY(16).
Remember that we have successfully issued READ CAPACITY(16) so we can
take the fast path on subsequent revalidate attempts.
Reported-by: Menion <menion@gmail.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:37:52 +0000 (08:37 +0100)]
scsi: remove the sym53c416 driver
This driver hasn't seen any recent bug fixing and is one of the last
drivers using the scsi_module.c infrastruture that has been deprecated
15 years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:37:51 +0000 (08:37 +0100)]
scsi: remove the NCR53c406a driver
This driver hasn't seen any recent bug fixing and is one of the last
drivers using the scsi_module.c infrastruture that has been deprecated
15 years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:37:50 +0000 (08:37 +0100)]
scsi: remove the fdomain and fdomain_cs drivers
These drivers haven't seen any recent bug fixing and are two of the last
drivers using the scsi_module.c infrastruture that has been deprecated
15 years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:37:49 +0000 (08:37 +0100)]
scsi: mvme147: stop using scsi_module.c
Convert the driver to modern style probing. Given that there only is a
single instance for a given board that can be done using a global struct
Scsi_Host instance easily.
Also fix the removal path by passing the correct cookie to free_irq, and
enable it unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:37:48 +0000 (08:37 +0100)]
scsi: esas2r: remove initialization / cleanup dead wood
esas2r has been converted to hotplug style initialization long ago, but
kept various remant of the old-style scsi_module.c initialization
around. Remove those.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 19 Mar 2018 07:34:58 +0000 (08:34 +0100)]
scsi: core: unexport scsi_host_set_state
This function is only used inside the SCSI midlayer, so remove the
export for it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Brian King [Wed, 14 Mar 2018 22:13:39 +0000 (17:13 -0500)]
scsi: ibmvfc: Avoid unnecessary port relogin
Following an RSCN, ibmvfc will issue an ADISC to determine if the
underlying target has changed, comparing the SCSI ID, WWPN, and WWNN to
determine how to handle the rport in discovery. However, the comparison
of the WWPN and WWNN was performing a memcmp between a big endian field
against a CPU endian field, which resulted in the wrong answer on LE
systems. This was observed as unexpected errors getting logged at boot
time as targets were getting relogins when not needed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stephen Kitt [Thu, 8 Mar 2018 21:38:41 +0000 (22:38 +0100)]
scsi: bfa: remove VLA
In preparation to enabling -Wvla, remove VLAs and replace them with
fixed-length arrays instead.
bfad_bsg.c uses a variable-length array declaration to measure the
size of a putative array; this can be replaced by the product of the
size of an element and the number of elements, avoiding the VLA
altogether.
This was prompted by https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Stephen Kitt <steve@sk2.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stephen Kitt [Thu, 8 Mar 2018 20:51:58 +0000 (21:51 +0100)]
scsi: aic7xxx: aic79xx: remove VLAs
In preparation to enabling -Wvla, remove VLAs and replace them with
fixed-length arrays instead.
The arrays fixed here, using the number of constant sections, aren't
really VLAs, but they appear so to the compiler. Replace the array sizes
with a pre-processor-level constant instead using ARRAY_SIZE.
This was prompted by https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Stephen Kitt <steve@sk2.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Pittman [Wed, 14 Mar 2018 13:52:36 +0000 (09:52 -0400)]
scsi: scsi_dh_alua: Correct comment for alua_alloc_pg()
In the comment for function alua_alloc_pg() the argument '@h' is
mistakenly referred to. Fix this by replacing it with the correct
argument reference, '@tpgs', and provide a short description.
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 13 Mar 2018 12:08:49 +0000 (12:08 +0000)]
scsi: lpfc: make several unions static, fix non-ANSI prototype
There are several unions that are local to the source and do not need to
be in global scope, so make them static. Also add in a missing void
parameter to functions lpfc_nvme_cmd_template and
lpfc_nvmet_cmd_template to clean up non-ANSI warning.
Cleans up sparse warnings:
drivers/scsi/lpfc/lpfc_nvme.c:68:19: warning: symbol
'lpfc_iread_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:69:19: warning: symbol
'lpfc_iwrite_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:70:19: warning: symbol
'lpfc_icmnd_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvme.c:74:24: warning: non-ANSI function
'lpfc_tsend_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:78:19: warning: symbol
'lpfc_treceive_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:79:19: warning: symbol
'lpfc_trsp_cmd_template' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:83:25: warning: non-ANSI function
declaration of function 'lpfc_nvmet_cmd_template'
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ming Lei [Tue, 13 Mar 2018 09:42:43 +0000 (17:42 +0800)]
scsi: virtio_scsi: unify scsi_host_template
Now that virtio_scsi uses blk-mq exclusively, we can remove the
scsi_host_template and associated plumbing for the legacy I/O path.
[mkp: commit desc]
Cc: Omar Sandoval <osandov@fb.com>, Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Laurence Oberman <loberman@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Suggested-by: Christoph Hellwig <hch@lst.de>, Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ming Lei [Tue, 13 Mar 2018 09:42:42 +0000 (17:42 +0800)]
scsi: virtio_scsi: fix IO hang caused by automatic irq vector affinity
Since commit 84676c1f21e8ff5 ("genirq/affinity: assign vectors to all
possible CPUs") it is possible to end up in a scenario where only
offline CPUs are mapped to an interrupt vector.
This is only an issue for the legacy I/O path since with blk-mq/scsi-mq
an I/O can't be submitted to a hardware queue if the queue isn't mapped
to an online CPU.
Fix this issue by forcing virtio-scsi to use blk-mq.
[mkp: commit desc]
Cc: Omar Sandoval <osandov@fb.com>, Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Don Brace <don.brace@microsemi.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Laurence Oberman <loberman@redhat.com> Fixes: 84676c1f21e8 ("genirq/affinity: assign vectors to all possible CPUs") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ming Lei [Tue, 13 Mar 2018 09:42:41 +0000 (17:42 +0800)]
scsi: core: introduce force_blk_mq
This patch introduces 'force_blk_mq' to the scsi_host_template so that
drivers that have no desire to support the legacy I/O path can signal
blk-mq only support.
[mkp: commit desc]
Cc: Omar Sandoval <osandov@fb.com>, Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Don Brace <don.brace@microsemi.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Laurence Oberman <loberman@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ming Lei [Tue, 13 Mar 2018 09:42:40 +0000 (17:42 +0800)]
scsi: megaraid_sas: fix selection of reply queue
Since commit 84676c1f21e8 ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.
Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de> Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Don Brace <don.brace@microsemi.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Laurence Oberman <loberman@redhat.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Meelis Roos <mroos@linux.ee> Cc: Artem Bityutskiy <artem.bityutskiy@intel.com> Fixes: 84676c1f21e8 ("genirq/affinity: assign vectors to all possible CPUs") Signed-off-by: Ming Lei <ming.lei@redhat.com> Acked-by: Kashyap Desai <kashyap.desai@broadcom.com> Tested-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Artem Bityutskiy <artem.bityutskiy@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ming Lei [Tue, 13 Mar 2018 09:42:39 +0000 (17:42 +0800)]
scsi: hpsa: fix selection of reply queue
Since commit 84676c1f21e8 ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.
Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de> Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Don Brace <don.brace@microsemi.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Laurence Oberman <loberman@redhat.com> Cc: Meelis Roos <mroos@linux.ee> Cc: Artem Bityutskiy <artem.bityutskiy@intel.com> Cc: Mike Snitzer <snitzer@redhat.com> Fixes: 84676c1f21e8 ("genirq/affinity: assign vectors to all possible CPUs") Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Tested-by: Don Brace <don.brace@microsemi.com> Tested-by: Artem Bityutskiy <artem.bityutskiy@intel.com> Acked-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stephen Kitt [Fri, 9 Mar 2018 22:32:11 +0000 (23:32 +0100)]
scsi: device_handler: remove VLAs
In preparation to enabling -Wvla, remove VLAs and replace them with
fixed-length arrays instead.
scsi_dh_{alua,emc,rdac} use variable-length array declarations to store
command blocks, with the appropriate size as determined by
COMMAND_SIZE. This patch replaces these with fixed-sized arrays using
MAX_COMMAND_SIZE, so that the array size can be determined at compile
time.
This was prompted by https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Stephen Kitt <steve@sk2.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Wed, 7 Mar 2018 06:56:41 +0000 (17:56 +1100)]
scsi: jazz_esp, sun3x_esp: Pass struct device pointer in dma calls
In jazz_esp and sun3x_esp, the esp_driver_ops methods pass esp->dev in
dma api calls as if it was a pointer to a struct device. But it actually
points to a struct platform_device. Fix this.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Wed, 7 Mar 2018 12:25:14 +0000 (20:25 +0800)]
scsi: hisi_sas: add v3 hw MODULE_DEVICE_TABLE()
Export device table of v3 hw to userspace, or auto probe will fail for v3
hw.
Also change the module alias to include "pci", instead of "platform".
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:13 +0000 (20:25 +0800)]
scsi: hisi_sas: modify some register config for hip08
Do some modifications for register configuring for hip08.
In future, to reduce kernel churn with patches to modify registers, any
registers which may change between board models (mostly PHY/SERDES related)
should be set in ACPI reset handler.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Wed, 7 Mar 2018 12:25:12 +0000 (20:25 +0800)]
scsi: hisi_sas: Code cleanup and minor bug fixes
The patch does some code cleanup and fixes some small bugs:
- Correct return status of phy_up_v3_hw() and phy_bcast_v3_hw()
- Add static for function phy_get_max_linkrate_v3_hw()
- Change exception return status when no reset method
- Change magic value to ts->stat in slot_complete_vx_hw()
- Remove unnecessary check for dev_is_sata()
- Fix some issues of alignment and indents (Authored by Xiaofei Tan in
another patch, but added here to be practical)
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:11 +0000 (20:25 +0800)]
scsi: hisi_sas: fix return value of hisi_sas_task_prep()
It is an implicit regulation that error code that function returned should
be negative. But hisi_sas_task_prep() doesn't follow this. This may cause
problems in the upper layer code.
For example, in sas_expander.c of libsas, smp_execute_task_sg() may return
the number of bytes of underrun. It will be conflicted with the scenaio
lldd_execute_task() return an positive error code.
This patch change the return value from SAS_PHY_DOWN to -ECOMM in
hisi_sas_task_prep().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The structure element hisi_sas_devices.running_req to count how many
commands are active is in effect only ever written in the code, so remove
it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:09 +0000 (20:25 +0800)]
scsi: hisi_sas: increase timer expire of internal abort task
The current 110ms expiry time is not long enough for the internal abort
task.
The reason is that the internal abort task could be blocked in HW if the HW
is retrying to set up link. The internal abort task will be executed only
when the retry process finished.
The maximum time is 5s for the retry of setting up link. So, the timer
expire should be more than 5s. This patch increases it from 110ms to 6s.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:08 +0000 (20:25 +0800)]
scsi: hisi_sas: fix the issue of setting linkrate register
It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:07 +0000 (20:25 +0800)]
scsi: hisi_sas: fix the issue of link rate inconsistency
In sysfs, there are two files about minimum linkrate, and also two files for
maximum linkrate. Take maximum linkrate example, maximum_linkrate_hw is
read-only and indicated by the register HARD_PHY_LINKRATE, and
maximum_linkrate is read-write and corresponding to the register
PROG_PHY_LINK_RATE.
But in the function phy_up_v*_hw(), we get *_linkrate value from
HARD_PHY_LINKRATE. It is not right. This patch is to fix this issue.
Unreferenced PHY-interrupt enum is also removed for v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:06 +0000 (20:25 +0800)]
scsi: hisi_sas: support the property of signal attenuation for v2 hw
The register SAS_PHY_CTRL is configured according to signal quality. The
signal quality is calculated by signal attenuation of hardware physical
link. It may be different for different PCB layout.
So, in order to give better support to new board, this patch add support to
reading the devicetree property, "hisilicon,signal-attenuation". Of course,
we still keep an default value in driver to adapt old board.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:05 +0000 (20:25 +0800)]
scsi: hisi_sas: dt-bindings: add an property of signal attenuation
For some new boards with hip07 chipset we are required to set PHY config
registers differently. The hw property which determines how to set these
registers is in the PHY signal attenuation readings.
This patch add an devicetree property, "hisilicon,signal-attenuation", which
is used to describe the signal attenuation of an board.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Douglas Gilbert [Wed, 7 Mar 2018 03:19:49 +0000 (22:19 -0500)]
scsi: core: Make SCSI Status CONDITION MET equivalent to GOOD
The SCSI PRE-FETCH (10 or 16) command is present both on hard disks
and some SSDs. It is useful when the address of the next block(s) to
be read is known but it is not following the LBA of the current READ
(so read-ahead won't help). It returns two "good" SCSI Status values.
If the requested blocks have fitted (or will most likely fit (when
the IMMED bit is set)) into the disk's cache, it returns CONDITION
MET. If it didn't (or will not) fit then it returns GOOD status.
The goal of this patch is to stop the SCSI subsystem treating the
CONDITION MET SCSI status as an error. The current state makes the
PRE-FETCH command effectively unusable via pass-throughs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:10 +0000 (12:04 -0800)]
scsi: lpfc: Change Copyright of 12.0.0.1 modified files to 2018
Updated Copyright in files updated as part of 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:09 +0000 (12:04 -0800)]
scsi: lpfc: update driver version to 12.0.0.1
Update the driver version to 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:08 +0000 (12:04 -0800)]
scsi: lpfc: Memory allocation error during driver start-up on power8
The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4
There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment. The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.
Fix by explicitly tracking sli4 vs sli3 and BG options. The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:07 +0000 (12:04 -0800)]
scsi: lpfc: Fix mailbox wait for POST_SGL mbox command
POST_SGL_PAGES mailbox command failed with status (timeout).
wait_event_interruptible_timeout when called from mailbox wait interface,
gets interrupted, and will randomly fail. Behavior seems very specific to 1
particular server type.
Fix by changing from wait_event_interruptible_timeout to
wait_for_completion_timeout.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:06 +0000 (12:04 -0800)]
scsi: lpfc: Fix SCSI lun discovery when port configured for both SCSI and NVME
When a port is configured for NVME and SCSI Initiator support and it probes
a target supporting both SCSI and NVME, NVME devices are discovered, but
SCSI devices are not.
The nlp_fc4_type for all NPorts should be cleared on Link Up or just before
GID_FTs get issued, as opposed to just during GID_FT cmpl. RSCN activity as
well as Link Up can trigger GID_FT. One GID_FT may complete before the next
one is issued.
Fix by clearng nlp_fc4_type on link up and just before both GID_FTs are
issued. During port swapping, copy nlp_fc4_type to the new ndlp
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:05 +0000 (12:04 -0800)]
scsi: lpfc: Streamline NVME Targe6t WQE setup
To reduce latency when initializing WQE content, created templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME target path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:04 +0000 (12:04 -0800)]
scsi: lpfc: Streamline NVME Initiator WQE setup
To reduce latency when initializing WQE content, create templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME initiator path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:03 +0000 (12:04 -0800)]
scsi: lpfc: Code cleanup for 128byte wqe data type
The driver is very sloppy about the WQE structure passed between routines.
The base struct type is a 64byte wqe. But in many routines they typecast and
access 128byte wqes. There were a couple of cases in the past (corrected
already) where the typecasts were incorrectly done and the 64byte buffer was
accessed as a 128 byte buffer.
Clean this up by properly declaring wqe's as 128byte wqe's and removing the
typecasts. 64byte wqes are considered a subset of the 128byte wqes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 20:04:02 +0000 (12:04 -0800)]
scsi: lpfc: Fix NVME Initiator FirstBurst
First Burst support was not properly indicated in NVMe PRLI.
Correct the bit position and the logic to check and set first burst support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 10 Mar 2018 18:28:48 +0000 (10:28 -0800)]
scsi: lpfc: Add missing unlock in WQ full logic
Commit 6e8e1c14c61e ("scsi: lpfc: Add WQ Full Logic for NVME Target") fails
the static checker. Checker correctly identified a missing unlock on a
return path.
Add the unlock.
Fixes: 6e8e1c14c61e ("scsi: lpfc: Add WQ Full Logic for NVME Target") Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Souptick Joarder [Thu, 8 Mar 2018 13:11:57 +0000 (18:41 +0530)]
scsi: ipr: Use dma_pool_zalloc()
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Wed, 7 Mar 2018 18:49:26 +0000 (10:49 -0800)]
scsi: qla2xxx: Remove FC_NO_LOOP_ID for FCP and FC-NVMe Discovery
Commit 7d64c39e64310 fixed regression of FCP discovery when Nport Handle
is in-use and relogin is triggered. However, during FCP and FC-NVMe
discovery this resulted into only discovering NVMe LUNs.
This patch fixes issue where FCP and FC-NVMe protocol is used on same
port where assigning FC_NO_LOOP_ID will result into discovery failure
for FCP LUNs.
Fixes: a084fd68e1d26 ("scsi: qla2xxx: Fix re-login for Nport Handle in use") Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jason Yan [Thu, 8 Mar 2018 02:34:53 +0000 (10:34 +0800)]
scsi: libsas: defer ata device eh commands to libata
When ata device doing EH, some commands still attached with tasks are
not passed to libata when abort failed or recover failed, so libata did
not handle these commands. After these commands done, sas task is freed,
but ata qc is not freed. This will cause ata qc leak and trigger a
warning like below:
If ata qc leaked too many, ata tag allocation will fail and io blocked
for ever.
As suggested by Dan Williams, defer ata device commands to libata and
merge sas_eh_finish_cmd() with sas_eh_defer_cmd(). libata will handle
ata qcs correctly after this.
Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: Xiaofei Tan <tanxiaofei@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This commit reads the disk's old state and combines it with the device
disk-reported state rather than unconditionally marking it as RW.
Reported-by: Li Ning <lining916740672@icloud.com> Signed-off-by: Jeremy Cline <jeremy@jcline.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bill Kuzeja [Mon, 5 Mar 2018 05:02:55 +0000 (00:02 -0500)]
scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure
Because of the shifting around of code in qla2x00_probe_one recently,
failures during adapter initialization can lead to problems, i.e. NULL
pointer crashes and doubly freed data structures which cause eventual
panics.
This V2 version makes the relevant memory free routines idempotent, so
repeat calls won't cause any harm. I also removed the problematic
probe_init_failed exit point as it is not needed.
Fixes: d64d6c5671db ("scsi: qla2xxx: Fix NULL pointer crash due to probe failure") Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Thu, 1 Mar 2018 22:19:28 +0000 (07:19 +0900)]
scsi: sd_zbc: Fix potential memory leak
Rework sd_zbc_check_zone_size() to avoid a memory leak due to an early
return if sd_zbc_report_zones() fails.
Reported-by: David.butterfield <david.butterfield@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: stable@vger.kernel.org Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 26 Feb 2018 14:26:01 +0000 (15:26 +0100)]
scsi: mpt3sas: Do not mark fw_event workqueue as WQ_MEM_RECLAIM
The firmware event workqueue should not be marked as WQ_MEM_RECLAIM
as it's doesn't need to make forward progress under memory pressure.
In the current state it will result in a deadlock if the device had been
forcefully removed.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 5 Mar 2018 18:29:03 +0000 (10:29 -0800)]
scsi: lpfc: use __raw_writeX on DPP copies
Commit 1351e69fc6db ("scsi: lpfc: Add push-to-adapter support to sli4")
fails compilation on some 32-bit systems as writeq() is not supported on
all architectures. Additionally, it was pointed out that as writeX()
does byteswapping if necessary for pci vs the cpu endianness, the code
was broken on BE PPC.
After discussions with Arnd Bergmann, we've resolved the issue
to the following:
Instead of writeX(), use __raw_writeX() - which writes to io
space while preserving byte order. To use this, the code
was changed to use a different buffer that lpfc prepped
via sli_pcimem_bcopy() that was set to the bytestream to
be written.
On platforms with __raw_writeq support, use the routine, otherwise
use __raw_writel()
[mkp: checkpatch]
Fixes: 1351e69fc6db ("scsi: lpfc: Add push-to-adapter support to sli4") Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jianchao Wang [Sat, 3 Mar 2018 01:54:09 +0000 (09:54 +0800)]
scsi: core: use blk_mq_requeue_request in __scsi_queue_insert
In scsi core, __scsi_queue_insert should just put request back on the
queue and retry using the same command as before. However, for blk-mq,
scsi_mq_requeue_cmd is employed here which will unprepare the
request. To align with the semantics of __scsi_queue_insert, use
blk_mq_requeue_request with kick_requeue_list == true and put the
reference of scsi_device.
Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Mon, 5 Mar 2018 15:01:00 +0000 (09:01 -0600)]
scsi: smartpqi: add in new supported controllers
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Thu, 1 Mar 2018 13:07:07 +0000 (14:07 +0100)]
scsi: mpt3sas: clarify mmio pointer types
The newly added code mixes up phys_addr_t/resource_size_t with dma_addr_t
and void pointers, as seen from these compiler warning:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_base_get_chain_phys':
drivers/scsi/mpt3sas/mpt3sas_base.c:235:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
base_chain_phys = (void *)ioc->chip_phys + MPI_FRAME_START_OFFSET +
^
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_clone_sg_entries':
drivers/scsi/mpt3sas/mpt3sas_base.c:427:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
sgel->Address = (dma_addr_t)dst_addr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:438:7: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:444:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
Both dma_addr_t and phys_addr_t may be wider than a pointer, so we must
avoid the conversion to pointer types. This also helps readability.
A second problem is treating MMIO addresses from a 'struct resource'
as addresses that can be used for DMA on that device. In almost all
cases, those are the same, but on some of the more obscure architectures,
PCI memory address 0 is mapped into the CPU address space at a nonzero
offset. I don't have a good fix for that, so I'm adding a comment here,
plus a WARN_ON() that triggers whenever the phys_addr_t number is
outside of the low 32-bit address space and causes a straight overflow
when assigned to the 32-bit sgel->Address.
Fixes: 182ac784b41f ("scsi: mpt3sas: Introduce Base function for cloning.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Wed, 14 Feb 2018 12:02:31 +0000 (15:02 +0300)]
scsi: atp870u: 64 bit bug in atp885_init()
On 64 bit CPUs there is a memory corruption bug on probe(). It should
be a u32 pointer instead of an unsigned long pointer or we write past
the end of the setupdata[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Thu, 1 Mar 2018 23:07:20 +0000 (15:07 -0800)]
scsi: ufs: Fix kernel-doc errors and warnings
Avoid that the kernel-doc tool complains about mismatches between
kernel-doc headers and function definitions. Avoid that errors like the
following are reported when building the UFS driver with W=1:
drivers/scsi/ufs/tc-dwc-g210-pci.c:60: error: Cannot parse struct or union!
drivers/scsi/ufs/tc-dwc-g210-pltfrm.c:26: warning: cannot understand function prototype: 'struct ufs_hba_variant_ops tc_dwc_g210_20bit_pltfm_hba_vops = '
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Vivek Gautam <vivek.gautam@codeaurora.org> Cc: Stanislav Nijnikov <stanislav.nijnikov@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that the kernel-doc tool complains about a mismatch between the
kernel-doc header and the function argument list.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Damien Le Moal <damien.lemoal@wdc.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trapp [Wed, 28 Feb 2018 00:31:12 +0000 (16:31 -0800)]
scsi: qla2xxx: Fix FC-NVMe LUN discovery
commit a4239945b8ad ("scsi: qla2xxx: Add switch command to simplify
fabric discovery") introduced regression when it did not consider
FC-NVMe code path which broke NVMe LUN discovery.
Fixes: a4239945b8ad ("scsi: qla2xxx: Add switch command to simplify fabric discovery") Signed-off-by: Darren Trapp <darren.trapp@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 26 Feb 2018 07:39:59 +0000 (08:39 +0100)]
scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()
When converting __scsi_error_from_host_byte() to BLK_STS error codes the
case DID_OK was forgotten, resulting in it always returning an error.
Fixes: 2a842acab109 ("block: introduce new block status code type") Cc: Doug Gilbert <dgilbert@interlog.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
projects / users / jedix / linux-maple.git / log