Arnd Bergmann [Mon, 30 Jan 2023 16:52:35 +0000 (17:52 +0100)]
Merge tag 'qcom-arm64-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 Devicetree updates for v6.3
This introduces support for the new Snapdragon 8 Gen 2 (SM8550)
platform. In addition to the adding support for the MTP on this
platform, support the following devices is introduced:
- GPLUS FL8005A
- Google Zombie with LTE and NVMe
- Google Zombie with NVMe
- Lenovo Tab P11
- Motorola G5 Plus
- Motorola G7 Power
- Motorola Moto G6
- Samsung Galaxy J5 (2016)
- Samsung Galaxy Tab A 8.0
- Samsung Galaxy Tab A 9.7
- Xiaomi Mi A1
- Xiaomi Mi A2 Lite
- Xiaomi Redmi 5 Plus
- Xiaomi Redmi Note 4X
On IPQ8074 the PCIe PHY register regions and PHY clock names are
corrected.
On MSM8916 DMA for the I2C controllers are introduced and blsp_dma is
unconditionally enabled. Per-sensor calibration data is provided for the
thermal sensor (tsens) block. The GPLUS FL8005A device is introduced and
gains support for touchscreen and flash LED. An additional Samsung
Galaxy J5 variant is added, and support is added for hall sensor and
MUIC.
Per-sensor calibration information is introduced for the thermal sensor
on MSM8956 as well.
On MSM8996, GPLL0 is added as a possible Kryo clock controller input, a
carveout is added to get modem metadata out of System RAM. Missing bus
clocks are added for agnoc2.
SDHCI1 is enabled on the Sony Xperia Tone platform and USB is limited to
high-speed, to make USB work.
MSM8998 gains the same modem carveout as other platforms, and the
description of the clock hierarchy is improved.
On QCS404 the clock hierarchy description is improved, the CDSP PAS node
is adjusted to match the binding and the thermal sensor (tsens) gains
per-sensor calibration information.
On SC7180 the Data Capture and Compare block is intorduced, and a
carveout for the modem metadata is introduced, to get this out of System
RAM. Pazquel360 gains touchscreen support, the regulator off-on-time is
adjusted for the Trogdor eDP and touchscreen.
Data lane and frequency properties are introduced for the DisplayPort
links.
SC7280 also gets Data Capture and Compare support, as well as the
dedicated modem metadata region. Herobrine gains DP audio support.
IPA description is updated so that it's only active on boards with a
modem.
On SC8280XP the display subsystem is introduced, currently with support
for most of the DisplayPort controllers. GPR, SoundWire and LPASS is
introduced, for audio support. Missing I2C and SPI controllers are
introduced.
Support for EDP is introduced for the CRD, the Lenovo ThinkPad X13s and
the SA8295P ADP automotive board. The SA8540P Ride platform enables one
i2c and pcie controllers.
A CMA region is defined for the CRD and X13s, to avoid allocation issues
from the NVMe support.
Fairphone FP3 gains NFC support and the Sony Xperia Nile platform gains
a description of simplefb.
SDM670 gains QFPROM definition.
SDM845 gains a carveout for the modem metadata and support for the Data
Capture and Compare block is introduced. Lenovo Yoga C630 firmware
paths are aligned with all other Qualcomm platforms.
On SM6125 apss SMMU is introduced and streams are defined for USB and
SDHCI controllers. GPI DMA description is introduced, as well as missing
SPI and I2C serial engines.
On Sony Xperia 10 IIa regulator definitions are improved, SDHCI2 is
introduced, and I2C and related GPI DMA blocks are enabled.
On SM6350 IPA is introduced. DDR and L3 scaling is introduced based on
CPUfreq.
Fairphone FP4, on SM7225 also has IPA enabled, and the Flash LED is
enabled as well.
On SM8150 the display subsystem is introduced, with clock controller,
DPU and two DSI controllers. The Data Capture and Compare block is
introduced.
For the Sony Xperia Kumano platform, GPIO keys and NFC support is
introduced.
For SM8350 PCIe is introduced, as is the display subsystem with display
clock controller, DPU and two DSI controllers. #interconnect-cells is
changed to 2, to align with other platforms and allow for active-only
votes. The display is enabled and the LT9611uxc found on the SM8350
Hardware Development Kit board is described, to provide HDMI output.
On SM8450 the display subsystem is introduced, with DPU and two DSI
controllers. GIC-ITS support is introduced for both PCIe0 and PCIe1.
SPMI bus support is introduced and pmics are wired up across the various
devices.
The display subsystem is enabled and the LT9611uxc is described to
provide HDMI output on the SM8450 Hardware Development Kit.
On Sony Xperia Nagara platform, GPIO keys and GPIO line names are
introduced. As is the SLG51000 PMIC and camera regulators are defined.
Support for SM8550 is introduced, with support for storage, USB,
remoteprocs, PCIe, low-speed buses, crypto and display subsystem. These
blocks are enabled on the MTP.
Lastly, the work continue to align Devicetree source with bindings
across all platforms.
* tag 'qcom-arm64-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (320 commits)
arm64: dts: qcom: sc7280: Add a carveout for modem metadata
arm64: dts: qcom: sc7180: Add a carveout for modem metadata
arm64: dts: qcom: sdm845: Add a carveout for modem metadata
arm64: dts: qcom: msm8998: Add a carveout for modem metadata
arm64: dts: qcom: msm8996: Add a carveout for modem metadata
arm64: dts: qcom: ipq8074: correct PCIe QMP PHY output clock names
arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
arm64: dts: qcom: ipq8074: set Gen2 PCIe pcie max-link-speed
arm64: dts: qcom: ipq8074: correct Gen2 PCIe ranges
arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY
arm64: dts: qcom: ipq8074: fix Gen2 PCIe QMP PHY
arm64: dts: qcom: sdm845-db845c: drop label from I2C controllers
arm64: dts: qcom: msm8996: support using GPLL0 as kryocc input
arm64: dts: qcom: sm8450: Allow both GIC-ITS and internal MSI controller
arm64: dts: qcom: sm8550-mtp: Add USB PHYs and HC nodes
arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes
arm64: dts: qcom: sm8250: drop unused properties from tx-macro
arm64: dts: qcom: sm8250: drop unused clock-frequency from wsa-macro
arm64: dts: qcom: align OPP table node name with DT schema
arm64: dts: qcom: rename mdp nodes to display-controller
...
Arnd Bergmann [Mon, 30 Jan 2023 16:48:54 +0000 (17:48 +0100)]
Merge tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/dt
RISC-V Devicetrees for v6.3-mw0
Microchip:
A vendor prefix for Aldec and both a binding and Devicetree for the
Aldec TySoM devkit for PolarFire SoC. This Devicetree corresponds to
what they are shipping in the SDK for rev2 boards.
StarFive:
Just the binding for the new StarFive JH7110 SoC and its first-party
SDC the VisionFive 2.
Other:
I was expecting the Devicetree for the aforementioned board to be ready
for this window, as the pinctrl driver had seem some review prior to
v6.2 and both it & the base clock drivers are heavily based on the
existing drivers for the JH7110.
That didn't come to be.. Christmas, the RISC-V Summit in December and
the Lunar New Year all playing a part perhaps.
Because of that, both Palmer and I have the Kconfig.socs work in our
branches, although in hindsight it probably wasn't needed here as I
only added the TySoM Devicetree & the conflict would've been trivial.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: add the Aldec TySoM's devicetree
dt-bindings: riscv: microchip: document the Aldec TySoM
dt-bindings: vendor-prefixes: Add entry for Aldec
RISC-V: stop directly selecting drivers for SOC_CANAAN
RISC-V: stop selecting SiFive clock and serial drivers directly
RISC-V: stop selecting the PolarFire SoC clock driver
RISC-V: kbuild: convert all use of SOC_FOO to ARCH_FOO
RISC-V: kconfig.socs: convert usage of SOC_CANAAN to ARCH_CANAAN
RISC-V: introduce ARCH_FOO kconfig aliases for SOC_FOO symbols
dt-bindings: riscv: Add StarFive JH7110 SoC and VisionFive 2 board
Arnd Bergmann [Thu, 26 Jan 2023 09:06:05 +0000 (10:06 +0100)]
Merge tag 'ux500-dts-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Some Ux500 DTS updates for the v6.3 kernel:
- Fix up LED node names
- Add a clkout-node for the external clock
* tag 'ux500-dts-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add clkout-clock node
ARM: dts: ste: align LED node names with dtschema
Arnd Bergmann [Wed, 25 Jan 2023 16:00:47 +0000 (17:00 +0100)]
Merge tag 'dt-cleanup-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into arm/dt
Minor improvements in ARM DTS for v6.3
1. Drop 0x from unit address (socpfga).
2. Align HDMI CEC and LED nodes with bindings (stih410, keystone, dove,
at91).
* tag 'dt-cleanup-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: at91: align LED node names with dtschema
ARM: dts: dove: align LED node names with dtschema
ARM: dts: keystone: align LED node names with dtschema
ARM: dts: stih410: align HDMI CEC node names with dtschema
ARM: dts: socfpga: drop 0x from unit address
Conor Dooley [Wed, 25 Jan 2023 11:09:32 +0000 (11:09 +0000)]
Merge patch series "Add a devicetree for the Aldec PolarFire SoC TySoM"
As it says on the tin, add a DT for this board. It's been sitting on my
desk for a while, so may as well have it upstream...
The DT is only partially complete, as it needs the fabric content added.
Unfortunately, I don't have a reference design in RTL or SmartDesign
for it and therefore don't know what that fabric content is.
Arnd Bergmann [Tue, 24 Jan 2023 20:57:52 +0000 (21:57 +0100)]
Merge tag 'samsung-drivers-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung SoC bindings changes for v6.3
1. System Controller: use dedicated/specific compatibles to identify
different controllers with different register layout (Exynos, Tesla
FSD). Extend the bindings with missing clocks.
2. Correct maintainers entry for Tesla FSD DTS.
* tag 'samsung-drivers-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
MAINTAINERS: arm64: tesla: correct pattern for directory
dt-bindings: soc: samsung: exynos-sysreg: correct indentation for deprecated
dt-bindings: soc: samsung: exynos-sysreg: add dedicated SYSREG compatibles to Exynosautov9
dt-bindings: soc: samsung: exynos-sysreg: add dedicated SYSREG compatibles to Exynos850
dt-bindings: soc: samsung: exynos-sysreg: Add tesla FSD sysreg compatibles
dt-bindings: soc: samsung: exynos-sysreg: add clocks for Exynos850
dt-bindings: soc: samsung: exynos-sysreg: add dedicated SYSREG compatibles to Exynos5433
dt-bindings: soc: samsung: exynos-sysreg: split from syscon
Arnd Bergmann [Tue, 24 Jan 2023 17:07:12 +0000 (18:07 +0100)]
Merge tag 'samsung-dt64-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v6.3
1. Add L2 cache properties (Exynos, Tesla FSD).
2. Tesla FSD: add Bosch MCAN (CAN bus), sound card (audio card with
codec and I2S controllers), system controller nodes.
3. Tesla FSD: correct pin pull up/down properties to match
recommendation in user manual.
4. Minor cleanups: use dedicated/specific sysreg compatibles, fix
dtbs_check warnings, drop unsupported properties1
* tag 'samsung-dt64-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: fsd: Add sound card node for Tesla FSD
arm64: dts: fsd: Add codec node for Tesla FSD
arm64: dts: fsd: Add I2S DAI node for Tesla FSD
arm64: dts: exynos: drop unsupported I2C properties in Espresso
arm64: dts: fsd: fix PUD values as per FSD HW UM
arm64: dts: exynos: add dedicated SYSREG compatibles to Exynosautov9
arm64: dts: exynos: add dedicated SYSREG compatibles to Exynos850
arm64: dts: fsd: add sysreg device node
arm64: dts: exynos: correct properties of MAX98504 in TM2
arm64: dts: exynos: drop clock-frequency from CPU nodes in TM2
arm64: dts: exynos: drop pwm-names from MAX77843 haptic in TM2
arm64: dts: exynos: use 8-bit for SPI IR LED duty-cycle in TM2
arm64: dts: exynos: add dedicated SYSREG compatibles to Exynos5433
arm64: dts: fsd: Add MCAN device node
arm64: dts: fsd: Update cache properties
arm64: dts: exynos: Update cache properties
Arnd Bergmann [Tue, 24 Jan 2023 17:06:42 +0000 (18:06 +0100)]
Merge tag 'dt64-cleanup-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into arm/dt
Minor improvements in ARM64 DTS for v6.3
1. Drop 0x from unit address (microchip).
2. Align HDMI CEC and LED nodes with bindings (hisilicon).
* tag 'dt64-cleanup-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
arm64: dts: hisilicon: align LED node names with dtschema
arm64: dts: microchip: drop 0x from unit address
Arnd Bergmann [Tue, 24 Jan 2023 17:03:20 +0000 (18:03 +0100)]
Merge tag 'renesas-dts-for-v6.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT updates for v6.3
- Enable watchdog and timer (OSTM) support for the RZ/Five SMARC EVK
development board,
- Add operating points for the Cortex-A55 CPU cores on the R-Car S4-8
SoC,
- Add display support for the R-Car V4H SoC and the White-Hawk
development board,
- Add eMMC and SDHI support for the RZ/V2M SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: condor-i: add HS400 support for eMMC
arm64: boot: dts: r8a774[a/b/e]1-beacon: Consolidate sound clocks
riscv: dts: renesas: rzfive-smarc-som: Enable OSTM nodes
arm64: dts: renesas: ulcb-kf: Fix pca9548 i2c-mux node names
arm64: dts: renesas: r9a09g011: Add eMMC and SDHI support
arm64: dts: renesas: white-hawk-cpu: Add DP output support
arm64: dts: renesas: r8a779g0: Add display related nodes
arm64: dts: renesas: r8a779f0: Add CA55 operating points
riscv: dts: renesas: rzfive-smarc-som: Enable WDT
Conor Dooley [Wed, 11 Jan 2023 12:41:05 +0000 (12:41 +0000)]
dt-bindings: vendor-prefixes: Add entry for Aldec
Per their website:
Aldec, Inc. is an industry-leading Electronic Design Automation (EDA)
company delivering innovative design creation, simulation and
verification solutions to assist in the development of complex FPGA,
ASIC, SoC and embedded system designs.
Link: https://www.aldec.com/ Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Andreas Kemnade [Tue, 17 Jan 2023 22:30:59 +0000 (23:30 +0100)]
ARM: dts: omap: gta04a5: cleanup i2c node names
Use generic node names.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <20230117223059.2609390-1-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Tue, 17 Jan 2023 22:30:02 +0000 (23:30 +0100)]
ARM: dts: omap: gta04: add BNO055 IMU chip
There is finally a driver upstreamed, so add the
device.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <20230117223002.2609301-1-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sicelo A. Mhlongo [Thu, 29 Dec 2022 17:13:48 +0000 (19:13 +0200)]
ARM: dts: n900: use iio driver for accelerometer
The accelerometer in the N900 is supported by the iio-framework since commit 8a7449d68670a8f9 ("iio: accel: add support for LIS302DL variant). This commit
switches to it and updates node properties to match the bindings of the new
compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Message-Id: <20221229171348.3543327-3-absicsz@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sicelo A. Mhlongo [Thu, 29 Dec 2022 17:13:47 +0000 (19:13 +0200)]
ARM: dts: n900: rename accelerometer node
Use generic node naming for lis302dl accelerometer, and drop its
label that is not used anywhere else.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Message-Id: <20221229171348.3543327-2-absicsz@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Jackson [Wed, 30 Nov 2022 14:05:47 +0000 (14:05 +0000)]
ARM: dts: am335x-nano: Enable USB host
Add missing entry to enable the USB host.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Message-Id: <20221130140547.295859-6-mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Jackson [Wed, 30 Nov 2022 14:05:46 +0000 (14:05 +0000)]
ARM: dts: am335x-nano: Fix GPIO settings for MMC pins
The MMC slot uses GPIO pins for Write Protext and Card Detect.
Define these so everything works correctly.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Message-Id: <20221130140547.295859-5-mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Jackson [Wed, 30 Nov 2022 14:05:45 +0000 (14:05 +0000)]
ARM: dts: am335x-nano: Enable I2C temperature sensor
The NanoBone platform supports a temperature sensor on the I2C bus.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Message-Id: <20221130140547.295859-4-mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Jackson [Wed, 30 Nov 2022 14:05:44 +0000 (14:05 +0000)]
ARM: dts: am335x-nano: Enable RS485 mode for UART3 & 4
UART3 & 4 are both RS485 ports.
So we need to configure and enable this by default.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Message-Id: <20221130140547.295859-3-mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Jackson [Wed, 30 Nov 2022 14:05:43 +0000 (14:05 +0000)]
ARM: dts: am335x-nano: Fix GPIO settings for RTS/CTS pins on UART3 & 4
The NanoBone platform uses GPIO pins for RTS/CTS control.
The DTS still uses the hardware RTS/CTS pins so this needs fixing.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Message-Id: <20221130140547.295859-2-mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Geert Uytterhoeven [Fri, 2 Dec 2022 16:49:16 +0000 (17:49 +0100)]
ARM: dts: ti: Fix pca954x i2c-mux node names
"make dtbs_check":
arch/arm/boot/dts/am3874-iceboard.dtb: pca9548@70: $nodename:0: 'pca9548@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm/boot/dts/am3874-iceboard.dtb: pca9548@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4', 'i2c@5', 'i2c@6', 'i2c@7' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Message-Id: <bc964109db8a5f29124580165e925bd3bfe36661.1669999298.git.geert+renesas@glider.be> Signed-off-by: Tony Lindgren <tony@atomide.com>
Laurent Pinchart [Wed, 15 Jun 2022 22:14:08 +0000 (01:14 +0300)]
ARM: dts: omap: Use new media bus type macros
Now that a header exists with macros for the media interface bus-type
values, replace hardcoding numerical constants with the corresponding
macros in the DT sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Message-Id: <20220615221410.27459-5-laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Current PCIe QMP PHY output name were changed in ("arm64: dts: qcom: Fix
IPQ8074 PCIe PHY nodes") however it did not account for the fact that GCC
driver is relying on the old names to match them as they are being used as
the parent for the gcc_pcie0_pipe_clk and gcc_pcie1_pipe_clk.
This broke parenting as GCC could not find the parent clock, so fix it by
changing to the names that driver is expecting.
Robert Marko [Fri, 13 Jan 2023 16:44:48 +0000 (17:44 +0100)]
arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
IPQ8074 comes in 2 silicon versions:
* v1 with 2x Gen2 PCIe ports and QMP PHY-s
* v2 with 1x Gen3 and 1x Gen2 PCIe ports and QMP PHY-s
v2 is the final and production version that is actually supported by the
kernel, however it looks like PCIe related nodes were added for the v1 SoC.
Finish the PCIe fixup by using the correct compatible, adding missing ATU
register space, declaring max-link-speed, use correct ranges, add missing
clocks and resets.
Robert Marko [Fri, 13 Jan 2023 16:44:44 +0000 (17:44 +0100)]
arm64: dts: qcom: ipq8074: set Gen2 PCIe pcie max-link-speed
Add the generic 'max-link-speed' property to describe the Gen2 PCIe link
generation limit.
This allows the generic DWC code to configure the link speed correctly.
Manivannan Sadhasivam [Wed, 11 Jan 2023 12:30:04 +0000 (18:00 +0530)]
arm64: dts: qcom: sm8450: Allow both GIC-ITS and internal MSI controller
The devicetree should specify both MSI implementations and the OS/driver
should choose the one based on the platform requirements. Currently, Linux
DWC driver will choose GIC-ITS over the internal MSI controller.
Fixes: a11bbf6adef4 ("arm64: dts: qcom: sm8450: Use GIC-ITS for PCIe0 and PCIe1") Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230111123004.21048-2-manivannan.sadhasivam@linaro.org
It seems that clock-output-names for the USB3 QMP PHY-s where set without
actually checking what is the GCC clock driver expecting, so clock core
could never actually find the parents for usb0_pipe_clk_src and
usb1_pipe_clk_src clocks in the GCC driver.
So, correct the names to be what the driver expects so that parenting
works.
Before:
gcc_usb0_pipe_clk_src 0 0 0 125000000 0 0 50000 Y
gcc_usb1_pipe_clk_src 0 0 0 125000000 0 0 50000 Y
After:
usb3phy_0_cc_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb0_pipe_clk_src 1 1 0 125000000 0 0 50000 Y
gcc_usb0_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb3phy_1_cc_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb1_pipe_clk_src 1 1 0 125000000 0 0 50000 Y
gcc_usb1_pipe_clk 1 1 0 125000000 0 0 50000 Y
Fixes: 5e09bc51d07b ("arm64: dts: ipq8074: enable USB support") Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230108130440.670181-2-robimarko@gmail.com
Jasper Korten [Sat, 7 Jan 2023 14:19:10 +0000 (19:19 +0500)]
arm64: dts: qcom: Add device tree for Samsung Galaxy Tab A 9.7 (2015)
The Galaxy Tab A 9.7 (2015) is a Snapdragon 410 based tablet.
This commit introduces basic support for the tablet including the
following features:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
- WCNSS (WiFi/BT)
- GPIO keys
- Fuel gauge
- Touchscreen
- Accelerometer
Part of the DT is split out into a common dtsi since the tablet shares
majority of the design with another variant having a different screen
size.
Brian Masney [Tue, 3 Jan 2023 18:22:29 +0000 (13:22 -0500)]
arm64: dts: qcom: sc8280xp: add rng device tree node
Add the necessary device tree node for qcom,prng-ee so we can use the
hardware random number generator. This functionality was tested on a
SA8540p automotive development board using kcapi-rng from libkcapi.
Brian Masney [Tue, 3 Jan 2023 18:22:28 +0000 (13:22 -0500)]
arm64: dts: qcom: sc8280xp: add aliases for i2c4 and i2c21
Add aliases for i2c4 and i2c21 to the crd and x13s DTS files so that
what's exposed to userspace doesn't change in the future if additional
i2c buses are enabled on these platforms.
Brian Masney [Tue, 3 Jan 2023 18:22:27 +0000 (13:22 -0500)]
arm64: dts: qcom: sa8540p-ride: add i2c nodes
Add the necessary nodes in order to get i2c0, i2c1, i2c12, i2c15, and
i2c18 functioning on the automotive board and exposed to userspace.
This work was derived from various patches that Qualcomm delivered
to Red Hat in a downstream kernel. This change was validated by using
i2c-tools 4.3.3 on CentOS Stream 9:
Brian Masney [Tue, 3 Jan 2023 18:22:24 +0000 (13:22 -0500)]
arm64: dts: qcom: sc8280xp: rename qup0_i2c4 to i2c4
In preparation for adding the missing SPI and I2C nodes to
sc8280xp.dtsi, it was decided to rename all of the existing qupX_
uart, spi, and i2c nodes to drop the qupX_ prefix. Let's go ahead
and rename qup0_i2c4 to i2c4.
Note that some nodes are moved in the file by this patch to preserve
the expected sort order in the file. Additionally, the properties
within the pinctrl state node are sorted to match the expected order
that's typically done in other DTs.
Brian Masney [Tue, 3 Jan 2023 18:22:23 +0000 (13:22 -0500)]
arm64: dts: qcom: sc8280xp: rename qup2_i2c5 to i2c21
In preparation for adding the missing SPI and I2C nodes to
sc8280xp.dtsi, it was decided to rename all of the existing qupX_
uart, spi, and i2c nodes to drop the qupX_ prefix. Let's go ahead
and rename qup2_i2c5 to i2c21. Under the old name, this was the 5th
index under qup2, which starts at index 16.
Note that some nodes are moved in the file by this patch to preserve
the expected sort order in the file. Additionally, the properties
within the pinctrl state node are sorted to match the expected order
that's typically done in other DTs.
Brian Masney [Tue, 3 Jan 2023 18:22:22 +0000 (13:22 -0500)]
arm64: dts: qcom: sc8280xp: rename qup2_uart17 to uart17
In preparation for adding the missing SPI and I2C nodes to
sc8280xp.dtsi, it was decided to rename all of the existing qupX_
uart, spi, and i2c nodes to drop the qupX_ prefix. Let's go ahead
and rename qup2_uart17 to uart17. Note that some nodes are moved in the
file by this patch to preserve the expected sort order in the file.
Konrad Dybcio [Mon, 2 Jan 2023 09:46:29 +0000 (10:46 +0100)]
arm64: dts: qcom: ipq6018: Add/remove some newlines
Some lines were broken very aggresively, presumably to fit under 80 chars
and some places could have used a newline, particularly between subsequent
nodes. Address all that and remove redundant comments near PCIe ranges
while at it so as not to exceed 100 chars needlessly.
Abel Vesa [Wed, 18 Jan 2023 23:05:26 +0000 (01:05 +0200)]
arm64: dts: qcom: sm8550-mtp: Add PCIe PHYs and controllers nodes
Enable PCIe controllers and PHYs nodes on SM8550 MTP board.
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230118230526.1499328-3-abel.vesa@linaro.org
This adds support for the aDSP, cDSP and MPSS Subsystems found in
the SM8550 SoC.
The aDSP, cDSP and MPSS needs:
- smp2p nodes to get event back from the subsystems
- remoteproc nodes with glink-edge subnodes providing all needed
resources to start and run the subsystems
In addition, the MPSS Subsystem needs a rmtfs_mem dedicated
memory zone.
projects / users / jedix / linux-maple.git / log