Dave Airlie [Thu, 14 Jan 2021 23:05:23 +0000 (09:05 +1000)]
Merge tag 'amd-drm-next-5.12-2021-01-08' of https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-5.12-2021-01-08:
amdgpu:
- Rework IH ring handling on vega and navi
- Rework HDP handling for vega and navi
- swSMU documenation updates
- Overdrive support for Sienna Cichlid and newer asics
- swSMU updates for vangogh
- swSMU updates for renoir
- Enable FP16 on DCE8-11
- Misc code cleanups and bug fixes
radeon:
- Fixes for platforms that can't access PCI resources correctly
- Misc code cleanups
Alexandre Demers [Thu, 7 Jan 2021 23:53:03 +0000 (18:53 -0500)]
drm/amdgpu: fix DRM_INFO flood if display core is not supported (bug 210921)
This fix bug 210921 where DRM_INFO floods log when hitting an unsupported ASIC in
amdgpu_device_asic_has_dc_support(). This info should be only called once.
Alex Deucher [Fri, 8 Jan 2021 16:32:11 +0000 (11:32 -0500)]
drm/amdgpu/display: fix build with CONFIG_DRM_AMD_DC_DCN disabled
dc_allow_idle_optimizations() needs to be protected by
CONFIG_DRM_AMD_DC_DCN.
Fixes: 71338cb4a7c2 ("drm/amd/display: enable idle optimizations for linux (MALL stutter)") Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Tue, 29 Dec 2020 10:32:11 +0000 (18:32 +0800)]
drm/amd/pm: modify the fine grain tuning function for Renoir
This patch is to improve the fine grain tuning function for Renoir.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together.
And the flag "od_enabled" is used to control the overdrive function for
dGPU, like navi10, navi14 and navi21.
APU like Renior or Vangogh uses this "od_enabled" to configure
the frequency range of gfx clock, but the max value of frequency
range will not be higher than the safe limit, it is not "overdrive".
So this patch adds two new flags -- "fine_grain_enabled" and
"fine_grain_started" to avoid this confusion, the flag will
make these two sysfs nodes work separately.
The flag "fine_grain_enabled" is set as "enabled" by default,
so the fine grain tuning function will be enabled by default.
But the flag "fine_grain_started" is set as "false" by default,
so the fine grain function will not take effect until it is set as
"true".
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag "fine_grain_started" will be set as "true",
and the fine grain tuning function will be started.
In other profile modes, including "auto", "high", "low", "profile_peak",
"profile_standard", "profile_min_sclk", "profile_min_mclk",
the flag "fine_grain_started" will be set as "false", and the od range of
fine grain tuning function will be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 7 Jan 2021 06:34:10 +0000 (14:34 +0800)]
drm/amd/pm: add the parameters of power profiles for vangogh
This pacth is to add the parameters of power profiles for vangogh,
includeing "profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk".
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tao Zhou [Wed, 6 Jan 2021 03:43:27 +0000 (11:43 +0800)]
drm/amdkfd: check more client ids in interrupt handler
Add check for SExSH clients in kfd interrupt handler.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Emily.Deng [Tue, 5 Jan 2021 03:21:25 +0000 (11:21 +0800)]
drm/amdgpu: Correct the read sclk for navi10
According to hw, after navi10,it runs in dfll mode, and should
read sclk from AverageGfxclkFrequency.
Signed-off-by: Emily.Deng <Emily.Deng@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Vetter [Thu, 7 Jan 2021 12:40:19 +0000 (13:40 +0100)]
Merge tag 'drm-misc-next-2021-01-06' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
Core Changes:
- Lots of drm documentation updates by Simor Ser.
- Require that each crtc has a unique primary plane.
- Add fixme that fbdev_generic_setup is confusing.
Driver Changes:
- Update addresses for TI display drivers maintainers.
- Make DRM_VIRTIO_GPU select VIRTIO.
- Small fixes to qxl, virtio, hisilicon, tve200, panel/s6e63m0.
Daniel Vetter [Thu, 7 Jan 2021 12:02:56 +0000 (13:02 +0100)]
Merge tag 'du-next-20210105' of git://linuxtv.org/pinchartl/media into drm-next
- Add default modes for connectors in unknown state
- R-Car DU conversion to DRM-managed API
- R-Car DU miscellaneous fixes
- Miscellaneous bridge and bridge bindings fixes
- Assorted misc driver cleanups
- Constify drm_driver for PCI devices
Daniel Vetter [Thu, 7 Jan 2021 11:20:28 +0000 (12:20 +0100)]
Merge tag 'drm-intel-next-2021-01-04' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Display hotplug fix for gen2/gen3 (Chris)
- Remove trailing semicolon (Tom)
- Suppress display warnings for old ifwi presend on our CI (Chris)
- OA/Perf related workaround (Lionel)
- Replace I915_READ/WRITE per new uncore and display read/write functions (Jani)
- PSR improvements (Jose)
- HDR and other color changes on LSPCON (Uma, Ville)
- FBC fixes for TGL (Uma)
- Record plane update times for debugging (Chris)
- Refactor panel backlight control functions (Dave)
- Display power improvements (Imre)
- Add VRR register definition (Manasi)
- Atomic modeset improvements for bigjoiner pipes (Ville)
- Switch off the scanout during driver unregister (Chris)
- Clean-up DP's FEW enable (Manasi)
- Fix VDSCP slice count (Manasi)
- Fix and clean up around rc_model_size for DSC (Jani)
- Remove Type-C noisy debug warn message (Sean)
- Display HPD code clean-up (Ville)
- Refactor Intel Display (Dave)
- Start adding support for Intel's eDP backlight controls (Lyude)
Daniel Vetter [Thu, 7 Jan 2021 10:23:38 +0000 (11:23 +0100)]
Merge tag 'imx-drm-next-2021-01-04' of git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: fixes and drm managed resources
- Reduce stack usage in ipu-di.
- Fix imx-ldb for compile tests.
- Make drm encoder control functions optional.
- Add drm managed variants drmm_encoder_alloc(),
drmm_simple_encoder_alloc(), drmm_universal_plane_alloc(), and
drmm_crtc_alloc_with_planes() for drm_encoder_init(),
drm_simple_encoder_init(), drm_universal_plane_init(), and
drm_crtc_init_with_planes(), respectively.
- Update imx-drm to use the new functions for drm managed resource
allocation, moving initialization from bind to probe where possible.
- Fix imx-tve clock provider leak.
Daniel Vetter [Thu, 7 Jan 2021 10:02:24 +0000 (11:02 +0100)]
Merge tag 'topic/dp-hdmi-2.1-pcon-2020-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Daniel Vetter [Thu, 7 Jan 2021 09:46:32 +0000 (10:46 +0100)]
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
This leads to blank screens on some boards after replugging a
display. Revert until we understand the root cause and can
fix both the leak and the blank screen after replug.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211033
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1427 Cc: Stylon Wang <stylon.wang@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Cc: Andre Tomt <andre@tomt.net> Cc: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Defang Bo [Tue, 5 Jan 2021 16:06:39 +0000 (00:06 +0800)]
drm/amdgpu: Add check to prevent IH overflow
Similar to commit <b82175750131>("drm/amdgpu: fix IH overflow on Vega10 v2").
When an ring buffer overflow happens the appropriate bit is set in the WPTR
register which is also written back to memory. But clearing the bit in the
WPTR doesn't trigger another memory writeback.
So what can happen is that we end up processing the buffer overflow over and
over again because the bit is never cleared. Resulting in a random system
lockup because of an infinite loop in an interrupt handler.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Defang Bo <bodefang@126.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Mon, 4 Jan 2021 16:24:20 +0000 (11:24 -0500)]
drm/amdgpu/display: drop DCN support for aarch64
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org> Reported-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Kleiner [Mon, 28 Dec 2020 18:50:59 +0000 (19:50 +0100)]
drm/amd/display: Enable fp16 also on DCE-8/10/11.
The hw supports fp16, this is not only useful for HDR,
but also for standard dynamic range displays, because
it allows to get more precise color reproduction with
about 11 - 12 bpc linear precision in the unorm range
0.0 - 1.0.
Working fp16 scanout+display (and HDR over HDMI) was
verified on a DCE-8 asic, so i assume that the more
recent DCE-10/11 will work equally well, now that
format-specific plane scaling constraints are properly
enforced, e.g., the inability of fp16 to scale on older
hw like DCE-8 to DCE-11.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Kleiner [Mon, 28 Dec 2020 18:50:58 +0000 (19:50 +0100)]
drm/amd/display: Check plane scaling against format specific hw plane caps.
This takes hw constraints specific to pixel formats into account,
e.g., the inability of older hw to scale fp16 format framebuffers.
It should now allow safely to enable fp16 formats also on DCE-8,
DCE-10, DCE-11.0
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.
Fixes: c920888c604d ("drm/amd/display: Expose new CRC window property") Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tian Tao [Mon, 21 Dec 2020 11:16:35 +0000 (19:16 +0800)]
drm/amd/display: remove useless else if
Fix the following coccinelle report:
drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c:1357:6-8:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Tue, 29 Dec 2020 09:19:37 +0000 (17:19 +0800)]
drm/amd/pm: improve the fine grain tuning function for RV/RV2/PCO
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Likun Gao [Mon, 28 Dec 2020 09:04:06 +0000 (17:04 +0800)]
drm/amdgpu: remove redundant logic related HDP
Remove hdp_flush function from amdgpu_nbio struct as it have been unified
into hdp struct.
Remove the include about hdp register which was not used.
V2: Remove hdp golden setting which is unnecessary.
Likun Gao [Mon, 28 Dec 2020 08:54:16 +0000 (16:54 +0800)]
drm/amdgpu: switch hdp callback functions for hdp v4
Switch to use the HDP functions which unified on hdp structure instead of
the scattered hdp callback functions.
V2: clean up hdp reset ras error count function.
Jiawei Gu [Wed, 23 Dec 2020 05:54:57 +0000 (13:54 +0800)]
drm/amdgpu: fix potential NULL pointer when check_atom_bios() fails
Asic funcs pointer needs being checked whether is NULL. Because when
check_atom_bios() fails in req_init_data handshake, asic funcs pointer
is not initialized yet.
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chen Li [Fri, 25 Dec 2020 03:58:00 +0000 (11:58 +0800)]
drm/amdgpu: use GTT for uvd_get_create/destory_msg
On modern gpus, GTT (system memory) works as well here, and this may
also be a workaround for platforms which cannot map vram correctly.
Signed-off-by: chenli <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Obviously, the __memset call is generated by gcc(8.3.1). It optimizes
this for loop into memset. But this may break on some platforms which
cannot map device memory correctly. So, just invoke `writel` to handle this.
v3 (chk): minor cleanups in code and commit message
Signed-off-by: Chen Li <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dennis Li [Wed, 30 Dec 2020 11:45:15 +0000 (19:45 +0800)]
drm/amdgpu: fix a GPU hang issue when remove device
When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Signed-off-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dennis Li [Wed, 30 Dec 2020 02:27:42 +0000 (10:27 +0800)]
drm/amdgpu: fix a memory protection fault when remove amdgpu device
ASD and TA share the same firmware in SIENNA_CICHLID and only TA
firmware is requested during boot, so only need release TA firmware when
remove device.
Signed-off-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 10:04:30 +0000 (18:04 +0800)]
drm/amd/pm: add support to umd P-state function for vangogh
This patch is to add support to umd P-state function for vangogh.
It enables the "set" function of 3 sysfs nodes: pp_dpm_mclk,
pp_dpm_fclk, pp_dpm_socclk, the functions is used to set the DPM
frequency level of memclk/fclk/socclk.
Due to only after enabling the "power_dpm_force_performance_level"
sysfs node, it is allowed to set these three nodes,
so this patch also enables the "powe_dpm_force_performance_level"
sysfs node, which is used to change power profile.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 08:19:19 +0000 (16:19 +0800)]
drm/amd/pm: add the fine grain tuning function for renoir
This patch is to add the fine grain tuning function for renoir.
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should
be limited in the safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "standard"
$ cat power_dpm_force_performance_level
auto
$ echo "profile_standard" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
profile_standard
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Fri, 18 Dec 2020 06:32:02 +0000 (14:32 +0800)]
drm/amd/pm: improve the fine grain tuning function for RV/RV2/PCO
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 08:11:33 +0000 (16:11 +0800)]
drm/amd/pm: enable the "fetch" function of pp_dpm_vclk/dclk for vangogh
This patch is to enable the "fetch" function of pp_dpm_vclk and
pp_dpm_dclk.
It allows to fetch the current frequency of vcn and dcn and their
DPM levels for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Wed, 16 Dec 2020 06:44:10 +0000 (14:44 +0800)]
drm/amd/pm: add two new sysfs nodes for vangogh
This patch is to add two new sysfs nodes for vangogh:
pp_dpm_dclk and pp_dpm_vclk.
The two sysfs nodes are similar to pp_dpm_fclk/memclk/socclk.
pp_dpm_dclk represents the DPM frequency of dcn unit.
pp_dpm_vclk represents the DPM frequency of vcn unit.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Wed, 16 Dec 2020 03:26:43 +0000 (11:26 +0800)]
drm/amd/pm: add new feature map macros to resolve duplicate name
This patch is to add new feature map macros to resolve duplicate name.
Vangogh uses one different format to name some feature bits of swSMU, it
causes some duplicate name in the existing feature map list.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Tue, 15 Dec 2020 08:41:26 +0000 (16:41 +0800)]
drm/amd/pm: add support to umd P-state "fetch" function for vangogh
This patch is to add supoort to umd P-state function for vangogh.
It enables the "fetch" function of 3 sysfs nodes: pp_dpm_mclk,
pp_dpm_fclk, pp_dpm_socclk,the function is used to fetch
the current frequency of memclk/fclk/socclk.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simon Ser [Tue, 22 Dec 2020 13:35:23 +0000 (14:35 +0100)]
drm/doc: demote old doc-comments in drm.h
Sphinx doesn't like old doc-comments in drm.h and generates warnings
like:
./include/uapi/drm/drm.h:87: warning: cannot understand function prototype: 'struct drm_clip_rect '
./include/uapi/drm/drm.h:97: warning: cannot understand function prototype: 'struct drm_drawable_info '
./include/uapi/drm/drm.h:105: warning: cannot understand function prototype: 'struct drm_tex_region '
...
Demote these to regular comments, because converting all of them is
quite a lot of work (also requires documenting all of the struct fields
for instance). Also many of these structures aren't really used by
modern user-space.
We can easily convert these remaining old comments to Sphinx style on a
one-by-one basis.
Laurent Pinchart [Tue, 15 Dec 2020 20:23:07 +0000 (22:23 +0200)]
drm: Constify drm_driver in drivers that don't modify it
A non-const structure containing function pointers is a possible attack
vector. The drm_driver structure is already const in most drivers, but
there are a few exceptions. Constify the structure in the drivers that
don't need to modify at, as a low-hanging fruit. The rest of the drivers
will need a more complex fix.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Laurent Pinchart [Thu, 20 Feb 2020 22:19:22 +0000 (00:19 +0200)]
drm: Use a const drm_driver for legacy PCI devices
Now that the legacy PCI support code doesn't need to write to the
drm_driver structure, it can be treated as const through the whole DRM
core, unconditionally. This allows declaring the structure as const in
all drivers, removing one possible attack vector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Laurent Pinchart [Thu, 20 Feb 2020 15:16:28 +0000 (17:16 +0200)]
drm: Move legacy device list out of drm_driver
The drm_driver structure contains a single field (legacy_dev_list) that
is modified by the DRM core, used to store a linked list of legacy DRM
devices associated with the driver. In order to make the structure
const, move the field out to a global variable. This requires locking
access to the global where the local field didn't require serialization,
but this only affects legacy drivers, and isn't in any hot path.
While at it, compile-out the legacy_dev_list field when DRM_LEGACY isn't
defined.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Laurent Pinchart [Fri, 4 Dec 2020 10:25:40 +0000 (12:25 +0200)]
drm: rcar-du: Drop local encoder variable
The local encoder variable is an alias for &renc->base, and is only use
twice. It doesn't help much, drop it, along with the
rcar_encoder_to_drm_encoder() macro that is then unused.
Laurent Pinchart [Thu, 3 Dec 2020 16:21:55 +0000 (18:21 +0200)]
drm: rcar-du: Skip encoder allocation for LVDS1 in dual-link mode
The rcar-du driver skips registration of the encoder for the LVDS1
output when LVDS is used in dual-link mode, as the LVDS0 and LVDS1 links
are bundled and handled through the LVDS0 output. It however still
allocates the encoder and immediately destroys it, which is pointless.
Skip allocation of the encoder altogether in that case.
Laurent Pinchart [Thu, 3 Dec 2020 16:21:55 +0000 (18:21 +0200)]
drm: rcar-du: Replace dev_private with container_of
Now that drm_device is embedded in rcar_du_device, we can use
container_of to get the rcar_du_device pointer from the drm_device,
instead of using the drm_device.dev_private field.
Laurent Pinchart [Thu, 3 Dec 2020 13:09:22 +0000 (15:09 +0200)]
drm: rcar-du: Use DRM-managed allocation for encoders
devm_kzalloc() is the wrong API to allocate encoders, as the lifetime of
the encoders is tied to the DRM device, not the device to driver
binding. drmm_kzalloc() isn't a good option either, as it would result
in the encoder being freed before being unregistered during the managed
cleanup of the DRM objects. Use a plain kzalloc(), and register a drmm
action to cleanup the encoder.
Laurent Pinchart [Thu, 3 Dec 2020 13:09:22 +0000 (15:09 +0200)]
drm: rcar-du: Use DRM-managed allocation for VSP planes
devm_kcalloc() is the wrong API to allocate planes, as the lifetime of
the planes is tied to the DRM device, not the device to driver
binding. drmm_kcalloc() isn't a good option either, as it would result
in the planes being freed before being unregistered during the managed
cleanup of the DRM objects. Use a plain kcalloc(), and cleanup the
planes and free the memory in the existing rcar_du_vsp_cleanup()
handler.
Laurent Pinchart [Thu, 3 Dec 2020 15:02:40 +0000 (17:02 +0200)]
drm: rcar-du: Drop unneeded encoder cleanup in error path
The encoder->name field can never be non-null in the error path, as that
can only be possible after a successful call to
drm_simple_encoder_init(). Drop the cleanup.
Laurent Pinchart [Fri, 4 Dec 2020 11:43:58 +0000 (13:43 +0200)]
drm: rcar-du: Fix crash when using LVDS1 clock for CRTC
On D3 and E3 platforms, the LVDS encoder includes a PLL that can
generate a clock for the corresponding CRTC, used even when the CRTC
output to a non-LVDS port. This mechanism is supported by the driver,
but the implementation is broken in dual-link LVDS mode. In that case,
the LVDS1 drm_encoder is skipped, which causes a crash when trying to
access its bridge later on.
Fix this by storing bridge pointers internally instead of retrieving
them from the encoder. The rcar_du_device encoders field isn't used
anymore and can be dropped.
Fixes: 8e8fddab0d0a ("drm: rcar-du: Skip LVDS1 output on Gen3 when using dual-link LVDS mode") Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Fri, 14 Jun 2013 00:55:25 +0000 (02:55 +0200)]
drm: Add default modes for connectors in unknown state
The DRM CRTC helpers add default modes to connectors in the connected
state if no mode can be retrieved from the connector. This behaviour is
useful for VGA or DVI outputs that have no connected DDC bus. However,
in such cases, the status of the output usually can't be retrieved and
is reported as connector_status_unknown.
Extend the addition of default modes to connectors in an unknown state
to support outputs that can retrieve neither the modes nor the
connection status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Qinglang Miao [Fri, 27 Nov 2020 09:44:44 +0000 (17:44 +0800)]
drm: rcar-du: Fix PM reference leak in rcar_cmm_enable()
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in a reference leak here.
A new function pm_runtime_resume_and_get is introduced in [0] to keep
usage counter balanced. So We fix the reference leak by replacing it
with new funtion.
[0] dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Fixes: e08e934d6c28 ("drm: rcar-du: Add support for CMM") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Acked-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The thc63lvd1024 driver requests a supply using regulator_get_optional()
but both the name of the supply and the usage pattern suggest that it is
being used for the main power for the device and is not at all optional
for the device for function, there is no handling at all for absent
supplies. Such regulators should use the vanilla regulator_get()
interface, it will ensure that even if a supply is not described in the
system integration one will be provided in software.
Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Philipp Zabel [Thu, 10 Dec 2020 15:38:45 +0000 (16:38 +0100)]
drm/imx: ipuv3-crtc: use drm managed resources
Use use drmm_crtc_alloc_with_planes() to align crtc memory lifetime
with the drm device. drm_crtc_cleanup() is called automatically before
the memory is freed.
Also use drmm_add_action_or_reset() to make sure IPU resources are
released automatically.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Philipp Zabel [Thu, 10 Dec 2020 15:38:44 +0000 (16:38 +0100)]
drm/imx: ipuv3-plane: use drm managed resources
Use drmm_universal_plane_alloc() to align plane memory lifetime with
the drm device. drm_plane_cleanup() is called automatically before the
memory is freed.
Also move the call to ipu_plane_get_resources() into ipu_plane_init()
and use drm managed resources to put IPU resources automatically when
required. Handle error return values of the plane property creation
functions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Philipp Zabel [Thu, 10 Dec 2020 15:38:43 +0000 (16:38 +0100)]
drm/imx: parallel-display: use drm managed resources
Use drmm_simple_encoder_alloc() to align encoder memory lifetime with
the drm device. drm_encoder_cleanup() is called automatically before
the memory is freed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Philipp Zabel [Thu, 10 Dec 2020 15:38:42 +0000 (16:38 +0100)]
drm/imx: imx-tve: use drm managed resources
Use drmm_simple_encoder_alloc() to align encoder memory lifetime with
the drm device. drm_encoder_cleanup() is called automatically before
the memory is freed.
Also fold imx_tve_register() into imx_tve_bind().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Philipp Zabel [Thu, 10 Dec 2020 15:38:41 +0000 (16:38 +0100)]
drm/imx: imx-ldb: use drm managed resources
Use drmm_simple_encoder_alloc() to align encoder memory lifetime with
the drm device. drm_encoder_cleanup() is called automatically before
the memory is freed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Philipp Zabel [Thu, 10 Dec 2020 15:38:39 +0000 (16:38 +0100)]
drm/imx: parallel-display: move initialization into probe
Parts of the initialization that do not require the drm device can be
done once during probe instead of possibly multiple times during bind.
The bind function only creates the encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux.git / log