The Tegra FUSE device tree bindings haven't been updated in a while. Add
compatible strings for the SoC generations that were released since the
last update.
The GV11B's device tree bindings are the same as for GP10B, though the
GPU is not completely compatible, so all that is needed is a different
compatible string.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge tag 'renesas-arm-dt-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.9 (take two)
- SPI Multi I/O Bus Controller (RPC-IF) support for R-Car V3H and V3M,
including QSPI support for the Condor, Eagle, V3HSK, and V3MSK
boards,
- Initial support for the RZ/G2H SoC on the HopeRun HiHope RZ/G2H
board,
- Initial support for the Beacon EmbeddedWorks RZ/G2M board,
- Minor fixes and improvements.
Geert Uytterhoeven [Tue, 19 May 2020 07:55:25 +0000 (09:55 +0200)]
ARM: dts: sh73a0: Add missing clocks to sound node
The device node for the FIFO-buffered Serial Interface sound node lacks
the "clocks" property, as the DTS file didn't describe any clocks yet at
its introduction.
The RZ/G2H (r8a774e1) comes with two clusters of processors, similarly to
the r8a774a1. The first cluster is made of A57s, the second cluster is made
of A53s.
The operating points for the cluster with the A57s are:
Frequency | Voltage
----------|---------
500 MHz | 0.82V
1.0 GHz | 0.82V
1.5 GHz | 0.82V
The operating points for the cluster with the A53s are:
Frequency | Voltage
----------|---------
800 MHz | 0.82V
1.0 GHz | 0.82V
1.2 GHz | 0.82V
This patch adds the definitions for the operating points to the SoC
specific DT.
Beacon EmebeddedWorks, formerly Logic PD is introducing a new
SOM and development kit based on the RZ/G2M SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display.
Merge tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More dts changes for omaps for v5.9
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
* tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT
ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP
ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP
ARM: dts: omap5-uevm: Add system timers to DSP and IPU
ARM: dts: omap5-uevm: Add CMA pools and enable IPU & DSP
ARM: dts: omap5: Add aliases for rproc nodes
ARM: dts: omap5: Add DSP and IPU nodes
ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU
ARM: dts: omap4-panda-common: Add CMA pools and enable IPU & DSP
ARM: dts: omap4: Add aliases for rproc nodes
ARM: dts: omap4: Add IPU DT node
ARM: dts: omap4: Update the DSP node
ARM: dts: omap5: Add timer_sys_ck clocks for timers
ARM: dts: omap4: Add timer_sys_ck clocks for timers
ARM: dts: am335x-pocketbeagle: set default mux for gpio pins
Merge tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop more legacy platform data for omaps for v5.9
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
* tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for omap5 usb host
ARM: OMAP2+: Drop legacy platform data for omap4 usb
ARM: OMAP2+: Drop legacy platform data for dra7 dwc3
ARM: OMAP2+: Drop legacy platform data for omap5 dwc3
ARM: OMAP2+: Drop legacy platform data for am4 dwc3
bus: ti-sysc: Add missing quirk flags for usb_host_hs
ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2
Dmitry Osipenko [Mon, 29 Jun 2020 02:54:53 +0000 (05:54 +0300)]
dt-bindings: Add vendor prefix for Acer Inc.
Acer is a hardware and electronics corporation, specializing in advanced
electronics technology. Acer's products include desktop PCs, laptop PCs,
tablets, servers, displays, storage devices, virtual reality devices,
smartphones and peripherals. Their web site is http://www.acer.com/.
Make the Makefile for building Renesas DTB files easier to read and
maintain:
- Get rid of line continuations,
- Use a single entry per line,
- Sort SoCs and boards alphabetically,
- Separate SoCs by blank lines.
Tony Lindgren [Mon, 13 Jul 2020 16:59:49 +0000 (09:59 -0700)]
ARM: OMAP2+: Drop legacy platform data for omap5 usb host
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tony Lindgren [Mon, 13 Jul 2020 16:59:49 +0000 (09:59 -0700)]
ARM: OMAP2+: Drop legacy platform data for omap4 usb
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tony Lindgren [Mon, 13 Jul 2020 16:59:48 +0000 (09:59 -0700)]
ARM: OMAP2+: Drop legacy platform data for dra7 dwc3
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tony Lindgren [Mon, 13 Jul 2020 16:59:48 +0000 (09:59 -0700)]
ARM: OMAP2+: Drop legacy platform data for omap5 dwc3
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Martin Blumenstingl [Sat, 20 Jun 2020 16:36:54 +0000 (18:36 +0200)]
ARM: dts: meson8b: odroidc1: enable the SDHC controller
Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.
Martin Blumenstingl [Sat, 20 Jun 2020 16:36:53 +0000 (18:36 +0200)]
ARM: dts: meson8b: ec100: enable the SDHC controller
EC-100 has built-in eMMC flash which is hard-wired to 3.3V VCC (which
means it's limited to high-speed MMC modes). Enable the SDHC controller
to access the contents of the eMMC flash.
Martin Blumenstingl [Sat, 20 Jun 2020 16:36:52 +0000 (18:36 +0200)]
ARM: dts: meson: add the SDHC MMC controller
Meson6, Meson8, Meson8b and Meson8m2 are using a similar SDHC controller
IP which typically connects to an eMMC chip (because unlike the SDIO
controller the SDHC controller has an 8-bit bus interface).
On Meson8, Meson8b and Meson8m2 the clock inputs are all the same.
However, Meson8m2 seems to have an improved version of the SHDC
controller IP which doesn't require the driver to wait manually for a
flush of a DMA transfer. Thus every SoC has it's own compatible string
so if more difference are discovered they can be implemented.
Martin Blumenstingl [Sat, 20 Jun 2020 16:23:47 +0000 (18:23 +0200)]
arm64: dts: amlogic: Add the Ethernet "timing-adjustment" clock
Add the "timing-adjustment" clock now that we know how it is connected
to the PRG_ETHERNET registers. It is used internally to generate the
RGMII RX delay on the MAC side (if needed).
Martin Blumenstingl [Sat, 20 Jun 2020 16:12:11 +0000 (18:12 +0200)]
arm64: dts: meson-gx: Switch to the meson-ee-pwrc bindings
The "amlogic,meson-gx-pwrc-vpu" binding only supports the VPU power
domain, while actually there are more power domains behind that set of
registers. Switch to the new bindings so we can add more power domains
as needed.
Martin Blumenstingl [Sat, 20 Jun 2020 16:10:10 +0000 (18:10 +0200)]
ARM: dts: meson8b: add power domain controller
The Meson8b SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Martin Blumenstingl [Sat, 20 Jun 2020 16:10:09 +0000 (18:10 +0200)]
ARM: dts: meson8m2: add resets for the power domain controller
The Meson8m2 SoCs has introduced additional reset lines for the VPU
compared to Meson8. Also it uses a slightly different VPU clock
frequency compared to Meson8 since it can now achieve 364MHz thanks to
the addition of the GP_PLL.
Add the reset lines, VPU clock configuration and update the compatible
string so the implementation differences can be managed.
Martin Blumenstingl [Sat, 20 Jun 2020 16:10:08 +0000 (18:10 +0200)]
ARM: dts: meson8: add power domain controller
The Meson8 SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Alexander A. Klimov [Wed, 8 Jul 2020 09:34:51 +0000 (11:34 +0200)]
Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:54 +0000 (18:19 -0500)]
ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP
The watchdog timers have been added for the IPU and DSP remoteproc
devices for the OMAP5 uEVM board. The following timers (same as the
timers on OMAP4 Panda boards) are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M4 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:53 +0000 (18:19 -0500)]
ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP
The watchdog timers have been added for the IPU and DSP remoteproc
devices on all the OMAP4-based Panda boards. The following timers
are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M3 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:52 +0000 (18:19 -0500)]
ARM: dts: omap5-uevm: Add system timers to DSP and IPU
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices for the OMAP5 uEVM boards. The following timers
(same as the timers on OMAP4 Panda boards) are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M4 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on the OMAP5 uEVM board. These nodes are assigned
to the respective rproc device nodes, and both the IPU and DSP remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:50 +0000 (18:19 -0500)]
ARM: dts: omap5: Add aliases for rproc nodes
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP5 boards. The aliases uses
the stem "rproc", and are identical to the values
chosen on OMAP4 boards.
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:49 +0000 (18:19 -0500)]
ARM: dts: omap5: Add DSP and IPU nodes
OMAP5, like OMAP4, also has two remote processor subsystems,
DSP and IPU. The IPU subsystem though has dual Cortex-M4
processors instead of the dual Cortex-M3 processors in OMAP4,
but otherwise has almost the same set of features. Add the
DT nodes for these two processor sub-systems for all OMAP5
SoCs.
The nodes have the 'iommus', 'clocks', 'resets', 'firmware' and
'mboxes' properties added, and are disabled for now. The IPU node
has its L2 RAM memory specified through the 'reg' and 'reg-names'
properties. The DSP node doesn't have these since it doesn't have
any L2 RAM memories, but has an additional 'ti,bootreg' property
instead as it has a specific boot register that needs to be
programmed for booting.
These nodes should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:48 +0000 (18:19 -0500)]
ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. The
following DMTimers are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M3 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. These nodes
are assigned to the respective rproc device nodes, and both the
IPU and DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:45 +0000 (18:19 -0500)]
ARM: dts: omap4: Add IPU DT node
The DT node for the Dual-Cortex M3 IPU processor sub-system has
been added for OMAP4 SoCs. The L2RAM memory region information
has been added to the node through the 'reg' and 'reg-names'
properties. The node has the 'iommus', 'clocks', 'resets',
'mboxes' and 'firmware' properties also added, and is disabled
for now. It should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:44 +0000 (18:19 -0500)]
ARM: dts: omap4: Update the DSP node
The compatible property for the DSP node is updated to match
the OMAP remoteproc bindings. The node is moved from the soc
node to the ocp node to better reflect the connectivity from
MPU side.
The node is updated with the 'ti,bootreg', 'clocks', 'resets',
'iommus', 'mboxes' and 'firmware' properties. Note that the
node does not have any 'reg' or 'reg-names' properties since
it doesn't have any L2 RAM memory, but only Unicaches.
The node is disabled for now, and should be enabled as per
the individual product configuration in the corresponding
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:43 +0000 (18:19 -0500)]
ARM: dts: omap5: Add timer_sys_ck clocks for timers
The commit d41e53040926 ("clk: ti: omap5: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes except for the always-on timers 1 and 12.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 9 Jul 2020 23:19:42 +0000 (18:19 -0500)]
ARM: dts: omap4: Add timer_sys_ck clocks for timers
The commit 1c7de9f27a65 ("clk: ti: omap4: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-pocketbeagle: set default mux for gpio pins
These pins on the PocketBeagle P1 and P2 headers are connected to AM3358
balls with gpio lines, and these pins are not used for any other
peripherals by default. These GPIO lines are unclaimed and could be used
by userspace program through the gpiod ABI.
This patch adds a "default" state in the am33xx_pinmux node and sets the
mux for those pins to gpio (mode 7) and input enable.
The "pinctrl-single,bias-pullup" and "pinctrl-single,bias-pulldown"
pinconf properties are also set for each pin per the ball reset state in
section 4.2 of the datasheet [0].
This is the AM335x pin control register format in Table 9-60 [1]:
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 1 0 x x x | 0x10
enabled x 1 0 x x x | 0x10
disabled x 0 0 x x x | 0x00
mask x 1 1 x x x | 0x18
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 0 0 x x x | 0x00
enabled x 0 0 x x x | 0x00
disabled x 1 0 x x x | 0x10
mask x 1 1 x x x | 0x18
Tony Lindgren [Mon, 13 Jul 2020 16:59:48 +0000 (09:59 -0700)]
ARM: OMAP2+: Drop legacy platform data for am4 dwc3
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
[tony@atomide.com: fixed typo for am3 vs am4] Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.9 please pull the following:
- Rafal specifies the switch ports for various Luxul devices (XAP-1410,
XAP-1510, XAP-1610, XWC-1000, XWC-2000, XWR-1200, XWR-3100, XWR-3150)
- Krzysztof fixes the L2 cache controller node name to conform to
dtschema
- Maxime introduces two new clock providers for Raspberry Pi 4, one to
support firmware based clocks and another one for the DVP block
feeding into the two HDMI blocks.
* tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Align L2 cache-controller nodename with dtschema
ARM: dts: BCM5301X: Specify switch ports for Luxul devices
ARM: dts: bcm2711: Add HDMI DVP
ARM: dts: bcm2711: Add firmware clocks node
Merge tag 'omap-for-v5.9/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.9 merge window
This series of changes configures the GPIO line names for am335x beaglebone
black and pocketbeagle to make it easier to configure the pins. To make use
of the pins, we also add the gpio-ranges for am335x.
We also enable IPU and DSP repmoteproc for am5729-beaglebone-ai, and then
there are two non-urgent dtschema validator warning fixes.
Merge tag 'uniphier-dt64-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.9
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add clock-names and reset-names to pcie-phy
* tag 'uniphier-dt64-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: Add missing clock-names and reset-names to pcie-phy
arm64: dts: uniphier: Rename ethphy node to ethernet-phy
arm64: dts: uniphier: give fixed port number to support card serial
arm64: dts: uniphier: add interrupts to support card serial
Merge tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.9
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add PCIe endpoint and PHY nodes for Pro5 SoC
- simplify device hierarchy of support-card.dtsi
* tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: simplify support-card node structure
ARM: dts: uniphier: Add PCIe endpoint and PHY node for Pro5
ARM: dts: uniphier: Rename ethphy node to ethernet-phy
ARM: dts: uniphier: give fixed port number to support card serial
ARM: dts: uniphier: rename support card serial node to fix schema warning
ARM: dts: uniphier: add interrupts to support card serial
This patch adds board HiHope RZ/G2H (the main board, powered by the
R8A774E1) and board HiHope RZ/G2 EX (the expansion board that sits on top
of the HiHope RZ/G2H). Both boards are made by Jiangsu HopeRun Software
Co., Ltd. (a.k.a. HopeRun).
Enric Balletbo i Serra [Thu, 25 Jun 2020 10:17:57 +0000 (12:17 +0200)]
arm64: dts: mt8183: Add krane-sku176 board
Also known as the Lenovo IdeaPad Duet Chromebook.
There are different krane boards with shared resources, hence a
mt8183-kukui-krane.dtsi was created for easily introduce future new
boards. The same happens with the baseboard codenamed kukui where
different variants, apart from kukui variant can take advantage of the
shared resources.
Signed-off-by: Ben Ho <Ben.Ho@mediatek.com>
[originally created by Ben Ho but adapted and ported to mainline] Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Tested-by: Hsin-Yi Wang <hsinyi@chromium.org> Link: https://lore.kernel.org/r/20200625101757.101775-8-enric.balletbo@collabora.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Thu, 25 Jun 2020 10:17:55 +0000 (12:17 +0200)]
arm64: dts: mt8183-evb: Fix unit name warnings
Remove the unit address from the DT nodes that doesn't have a reg
property. This fixes the following unit name warnings:
Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc0@0: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc1@0: node has a unit name, but no reg or ranges property
Enric Balletbo i Serra [Thu, 25 Jun 2020 10:17:54 +0000 (12:17 +0200)]
arm64: dts: mt8183: Fix unit name warnings
Remove the unit address from the DT nodes that doesn't have a reg
property. This fixes the following unit name warnings:
Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@0: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@1: node has a unit name, but no reg or ranges property
projects / users / willy / linux.git / log