There are a couple of nasty truncation bugs lurking in the pageattr
code that can be triggered when mapping EFI regions, e.g. when we pass
a cpa->pgd pointer. Because cpa->numpages is a 32-bit value, shifting
left by PAGE_SHIFT will truncate the resultant address to 32-bits.
Viorel-Cătălin managed to trigger this bug on his Dell machine that
provides a ~5GB EFI region which requires 1236992 pages to be mapped.
When calling populate_pud() the end of the region gets calculated
incorrectly in the following buggy expression,
end = start + (cpa->numpages << PAGE_SHIFT);
And only 188416 pages are mapped. Next, populate_pud() gets invoked
for a second time because of the loop in __change_page_attr_set_clr(),
only this time no pages get mapped because shifting the remaining
number of pages (1048576) by PAGE_SHIFT is zero. At which point the
loop in __change_page_attr_set_clr() spins forever because we fail to
map progress.
Hitting this bug depends very much on the virtual address we pick to
map the large region at and how many pages we map on the initial run
through the loop. This explains why this issue was only recently hit
with the introduction of commit
a5caa209ba9c ("x86/efi: Fix boot crash by mapping EFI memmap
entries bottom-up at runtime, instead of top-down")
It's interesting to note that safe uses of cpa->numpages do exist in
the pageattr code. If instead of shifting ->numpages we multiply by
PAGE_SIZE, no truncation occurs because PAGE_SIZE is a UL value, and
so the result is unsigned long.
To avoid surprises when users try to convert very large cpa->numpages
values to addresses, change the data type from 'int' to 'unsigned
long', thereby making it suitable for shifting by PAGE_SHIFT without
any type casting.
The alternative would be to make liberal use of casting, but that is
far more likely to cause problems in the future when someone adds more
code and fails to cast properly; this bug was difficult enough to
track down in the first place.
ALSA dummy driver can switch the timer backend between system timer
and hrtimer via its hrtimer module option. This can be also switched
dynamically via sysfs, but it may lead to a memory corruption when
switching is done while a PCM stream is running; the stream instance
for the newly switched timer method tries to access the memory that
was allocated by another timer method although the sizes differ.
As the simplest fix, this patch just disables the switch via sysfs by
dropping the writable bit.
Before this patch, a process with some permissive seccomp filter
that was applied by root without NO_NEW_PRIVS was able to add
more filters to itself without setting NO_NEW_PRIVS by setting
the new filter from a throwaway thread with NO_NEW_PRIVS.
Although n_tty_check_unthrottle() has a valid ldisc reference (since
the tty core gets the ldisc ref in tty_read() before calling the line
discipline read() method), it does not have a valid ldisc reference to
the "other" pty of a pty pair. Since getting an ldisc reference for
tty->link essentially open-codes tty_wakeup(), just replace with the
equivalent tty_wakeup().
Cc: <stable@vger.kernel.org> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 28b824966ab269de94e0ca640b7c61aedc6a83de)
Runtime suspend during driver probe and removal can cause problems.
The driver's runtime_suspend or runtime_resume callbacks may invoked
before the driver has finished binding to the device or after the
driver has unbound from the device.
This problem shows up with the sd and sr drivers, and can cause disk
or CD/DVD drives to become unusable as a result. The fix is simple.
The drivers store a pointer to the scsi_disk or scsi_cd structure as
their private device data when probing is finished, so we simply have
to be sure to clear the private data during removal and test it during
runtime suspend/resume.
This fixes <https://bugs.debian.org/801925>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Paul Menzel <paul.menzel@giantmonkey.de> Reported-by: Erich Schubert <erich@debian.org> Reported-by: Alexandre Rossi <alexandre.rossi@gmail.com> Tested-by: Paul Menzel <paul.menzel@giantmonkey.de> Tested-by: Erich Schubert <erich@debian.org> CC: <stable@vger.kernel.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 91e65860a7fe55d3d8c150104084b54f2760bc3d)
For PAE kernels "unsigned long" is not suitable to hold page protection
flags, since _PAGE_NX doesn't fit there. This is the reason for quite a
few W+X pages getting reported as insecure during boot (observed namely
for the entire initrd range).
KASan detected a use-after-free error in virtio-pci remove code. In
virtio_pci_remove(), vp_dev is still used after being freed in
unregister_virtio_device() (in virtio_pci_release_dev() more
precisely).
To fix, keep a reference until cleanup is done.
Fixes: 63bd62a08ca4 ("virtio_pci: defer kfree until release callback") Reported-by: Jerome Marchand <jmarchan@redhat.com> Cc: stable@vger.kernel.org Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 593bd1058b30eb4f0d6949afdfd9c2659d94ae1e)
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
In current acm driver, the bulk-in callback function ignores the
URBs unlinked in usb core.
This causes unexpected data loss in some cases. For example,
runtime suspend entry will unlinked all urbs and set urb->status
to -ENOENT even those urbs might have data not processed yet.
Hence, data loss occurs.
This patch lets bulk-in callback function handle unlinked urbs
to avoid data loss.
Signed-off-by: Tang Jian Qiang <jianqiang.tang@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Cc: stable@vger.kernel.org Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 6cdc037a9b649209051e3c982d5fcaf31274cb55)
NFS on a 2 node ocfs2 cluster each node exporting dir. The lock causing
the hang is the global bit map inode lock. Node 1 is master, has the
lock granted in PR mode; Node 2 is in the converting list (PR -> EX).
There are no holders of the lock on the master node so it should
downconvert to NL and grant EX to node 2 but that does not happen.
BLOCKED + QUEUED in lock res are set and it is on osb blocked list.
Threads are waiting in __ocfs2_cluster_lock on BLOCKED. One thread
wants EX, rest want PR. So it is as though the downconvert thread needs
to be kicked to complete the conv.
The hang is caused by an EX req coming into __ocfs2_cluster_lock on the
heels of a PR req after it sets BUSY (drops l_lock, releasing EX
thread), forcing the incoming EX to wait on BUSY without doing anything.
PR has called ocfs2_dlm_lock, which sets the node 1 lock from NL -> PR,
queues ast.
At this time, upconvert (PR ->EX) arrives from node 2, finds conflict
with node 1 lock in PR, so the lock res is put on dlm thread's dirty
listt.
After ret from ocf2_dlm_lock, PR thread now waits behind EX on BUSY till
awoken by ast.
Now it is dlm_thread that serially runs dlm_shuffle_lists, ast, bast, in
that order. dlm_shuffle_lists ques a bast on behalf of node 2 (which
will be run by dlm_thread right after the ast). ast does its part, sets
UPCONVERT_FINISHING, clears BUSY and wakes its waiters. Next,
dlm_thread runs bast. It sets BLOCKED and kicks dc thread. dc thread
runs ocfs2_unblock_lock, but since UPCONVERT_FINISHING set, skips doing
anything and reques.
Inside of __ocfs2_cluster_lock, since EX has been waiting on BUSY ahead
of PR, it wakes up first, finds BLOCKED set and skips doing anything but
clearing UPCONVERT_FINISHING (which was actually "meant" for the PR
thread), and this time waits on BLOCKED. Next, the PR thread comes out
of wait but since UPCONVERT_FINISHING is not set, it skips updating the
l_ro_holders and goes straight to wait on BLOCKED. So there, we have a
hang! Threads in __ocfs2_cluster_lock wait on BLOCKED, lock res in osb
blocked list. Only when dc thread is awoken, it will run
ocfs2_unblock_lock and things will unhang.
One way to fix this is to wake the dc thread on the flag after clearing
UPCONVERT_FINISHING
Orabug: 20933419 Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Cc: Eric Ren <zren@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit b085ab71a7e748a9edb77a36ceadbab514ce0947)
It happens on munlock_vma_page() due to unfortunate choice of nr_pages
data type:
__mod_zone_page_state(zone, NR_MLOCK, -nr_pages);
For unsigned int nr_pages, implicitly casted to long in
__mod_zone_page_state(), it becomes something around UINT_MAX.
munlock_vma_page() usually called for THP as small pages go though
pagevec.
Let's make nr_pages signed int.
Similar fixes in 6cdb18ad98a4 ("mm/vmstat: fix overflow in
mod_zone_page_state()") used `long' type, but `int' here is OK for a
count of the number of sub-pages in a huge page.
Fixes: ff6a6da60b89 ("mm: accelerate munlock() treatment of THP pages") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Michel Lespinasse <walken@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [4.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit d4dc115d9b67b7ec9769efd9b55d5bfce8d9ef20)
There are a number of problems with revoking a "was sending" message:
(1) We never make any attempt to revoke data - only kvecs contibute to
con->out_skip. However, once the header (envelope) is written to the
socket, our peer learns data_len and sets itself to expect at least
data_len bytes to follow front or front+middle. If ceph_msg_revoke()
is called while the messenger is sending message's data portion,
anything we send after that call is counted by the OSD towards the now
revoked message's data portion. The effects vary, the most common one
is the eventual hang - higher layers get stuck waiting for the reply to
the message that was sent out after ceph_msg_revoke() returned and
treated by the OSD as a bunch of data bytes. This is what Matt ran
into.
(2) Flat out zeroing con->out_kvec_bytes worth of bytes to handle kvecs
is wrong. If ceph_msg_revoke() is called before the tag is sent out or
while the messenger is sending the header, we will get a connection
reset, either due to a bad tag (0 is not a valid tag) or a bad header
CRC, which kind of defeats the purpose of revoke. Currently the kernel
client refuses to work with header CRCs disabled, but that will likely
change in the future, making this even worse.
(3) con->out_skip is not reset on connection reset, leading to one or
more spurious connection resets if we happen to get a real one between
con->out_skip is set in ceph_msg_revoke() and before it's cleared in
write_partial_skip().
Fixing (1) and (3) is trivial. The idea behind fixing (2) is to never
zero the tag or the header, i.e. send out tag+header regardless of when
ceph_msg_revoke() is called. That way the header is always correct, no
unnecessary resets are induced and revoke stands ready for disabled
CRCs. Since ceph_msg_revoke() rips out con->out_msg, introduce a new
"message out temp" and copy the header into it before sending.
Cc: stable@vger.kernel.org # 4.0+ Reported-by: Matt Conner <matt.conner@keepertech.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Matt Conner <matt.conner@keepertech.com> Reviewed-by: Sage Weil <sage@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 65a7633357c158ed164878d97e8a7fc09fb75946)
An unprivileged user can trigger an oops on a kernel with
CONFIG_CHECKPOINT_RESTORE.
proc_pid_cmdline_read takes mmap_sem for reading and obtains args + env
start/end values. These get sanity checked as follows:
BUG_ON(arg_start > arg_end);
BUG_ON(env_start > env_end);
These can be changed by prctl_set_mm. Turns out also takes the semaphore for
reading, effectively rendering it useless. This results in:
Turns out there are instances where the code just reads aformentioned
values without locking whatsoever - namely environ_read and get_cmdline.
Interestingly these functions look quite resilient against bogus values,
but I don't believe this should be relied upon.
The first patch gets rid of the oops bug by grabbing mmap_sem for
writing.
The second patch is optional and puts locking around aformentioned
consumers for safety. Consumers of other fields don't seem to benefit
from similar treatment and are left untouched.
This patch (of 2):
The code was taking the semaphore for reading, which does not protect
against readers nor concurrent modifications.
The problem could cause a sanity checks to fail in procfs's cmdline
reader, resulting in an OOPS.
Note that some functions perform an unlocked read of various mm fields,
but they seem to be fine despite possible modificaton.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Jarod Wilson <jarod@redhat.com> Cc: Jan Stancek <jstancek@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Anshuman Khandual <anshuman.linux@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 92d4a19886bcce4cca4c9f993a7324ac607d142c)
Some string_get_size() calls (e.g.:
string_get_size(1, 512, STRING_UNITS_10, ..., ...)
string_get_size(15, 64, STRING_UNITS_10, ..., ...)
) result in an infinite loop. The problem is that if size is equal to
divisor[units]/blk_size and is smaller than divisor[units] we'll end
up with size == 0 when we start doing sf_cap calculations:
For string_get_size(1, 512, STRING_UNITS_10, ..., ...) case:
...
remainder = do_div(size, divisor[units]); -> size is 0, remainder is 1
remainder *= blk_size; -> remainder is 512
...
size *= blk_size; -> size is still 0
size += remainder / divisor[units]; -> size is still 0
The caller causing the issue is sd_read_capacity(), the problem was
noticed on Hyper-V, such weird size was reported by host when scanning
collides with device removal. This is probably a separate issue worth
fixing, this patch is intended to prevent the library routine from
infinite looping.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: James Bottomley <JBottomley@Odin.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 4aba5827e764110bd1462eecf79209e656090f9c)
record_obj() in migrate_zspage() does not preserve handle's
HANDLE_PIN_BIT, set by find_aloced_obj()->trypin_tag(), and implicitly
(accidentally) un-pins the handle, while migrate_zspage() still performs
an explicit unpin_tag() on the that handle. This additional explicit
unpin_tag() introduces a race condition with zs_free(), which can pin
that handle by this time, so the handle becomes un-pinned.
Schematically, it goes like this:
CPU0 CPU1
migrate_zspage
find_alloced_obj
trypin_tag
set HANDLE_PIN_BIT zs_free()
pin_tag()
obj_malloc() -- new object, no tag
record_obj() -- remove HANDLE_PIN_BIT set HANDLE_PIN_BIT
unpin_tag() -- remove zs_free's HANDLE_PIN_BIT
The race condition may result in a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
CPU: 0 PID: 19001 Comm: CookieMonsterCl Tainted:
PC is at get_zspage_mapping+0x0/0x24
LR is at obj_free.isra.22+0x64/0x128
Call trace:
get_zspage_mapping+0x0/0x24
zs_free+0x88/0x114
zram_free_page+0x64/0xcc
zram_slot_free_notify+0x90/0x108
swap_entry_free+0x278/0x294
free_swap_and_cache+0x38/0x11c
unmap_single_vma+0x480/0x5c8
unmap_vmas+0x44/0x60
exit_mmap+0x50/0x110
mmput+0x58/0xe0
do_exit+0x320/0x8dc
do_group_exit+0x44/0xa8
get_signal+0x538/0x580
do_signal+0x98/0x4b8
do_notify_resume+0x14/0x5c
This patch keeps the lock bit in migration path and update value
atomically.
Signed-off-by: Junil Lee <junil0814.lee@lge.com> Signed-off-by: Minchan Kim <minchan@kernel.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: <stable@vger.kernel.org> [4.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 3730198645d95e2ac438ea9276402d3908b9449d)
We mark the end of the SG list in sendmsg and sendpage and unmark
it on the next send call. Unfortunately the unmarking in sendmsg
is off-by-one, leading to an SG list that is too short.
Fixes: 0f477b655a52 ("crypto: algif - Mark sgl end at the end of data") Cc: stable@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit a9c56fd066f9b5d222e0813b732908dabd721867)
This patch is a iscsi-target specific bug-fix for a dead-lock
that can occur during explicit struct se_node_acl->acl_group
se_session deletion via configfs rmdir(2), when iscsi-target
time2retain timer is still active.
It changes iscsi-target to obtain se_portal_group->session_lock
internally using spin_in_locked() to check for the specific
se_node_acl configfs shutdown rmdir(2) case.
Note this patch is intended for stable, and the subsequent
v4.5-rc patch converts target_core_tpg.c to use proper
se_sess->sess_kref reference counting for both se_node_acl
deletion + se_node_acl->queue_depth se_session restart.
Reported-by:: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <michaelc@cs.wisc.edu> Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 5446a444ae9e1976a77cb8faeab8198e44168daa)
This happens because we can recursively acquire the semaphore
fs_info->delayed_iput_sem when attempting to allocate space to satisfy
a file write request as shown in the first trace above - when committing
a transaction we acquire (down_read) the semaphore before running the
delayed iputs, and when running a delayed iput() we can end up calling
an inode's eviction handler, which in turn commits another transaction
and attempts to acquire (down_read) again the semaphore to run more
delayed iput operations.
This results in a deadlock because if a task acquires multiple times a
semaphore it should invoke down_read_nested() with a different lockdep
class for each level of recursion.
Fix this by simplifying the implementation and use a mutex instead that
is acquired by the cleaner kthread before it runs the delayed iputs
instead of always acquiring a semaphore before delayed references are
run from anywhere.
Fixes: d7c151717a1e (btrfs: Fix NO_SPACE bug caused by delayed-iput) Cc: stable@vger.kernel.org # 4.1+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit e004a097257612853c63b3f47726fe04981e94c2)
I don't think it makes sense for a module to have a soft dependency
on itself. This seems quite cyclic by nature and I can't see what
purpose it could serve.
OTOH libcrc32c calls crypto_alloc_shash("crc32c", 0, 0) so it pretty
much assumes that some incarnation of the "crc32c" hash algorithm has
been loaded. Therefore it makes sense to have the soft dependency
there (as crc-t10dif does.)
Cc: stable@vger.kernel.org Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 5d545a70cca8594f6120a9e3d70187920e62ce77)
Recently I've been seeing xfs/051 fail on 1k block size filesystems.
Trying to trace the events during the test lead to the problem going
away, indicating that it was a race condition that lead to this
ASSERT failure:
When I finally caught it with tracing enabled, I saw that AG 2 had
an elevated reference count and a buffer was responsible for it. I
tracked down the specific buffer, and found that it was missing the
final reference count release that would put it back on the LRU and
hence be found by xfs_wait_buftarg() calls in the log mount failure
handling.
The last four traces for the buffer before the assert were (trimmed
for relevance)
kworker/0:1-5259 xfs_buf_iodone: hold 2 lock 0 flags ASYNC
kworker/0:1-5259 xfs_buf_ioerror: hold 2 lock 0 error -5
mount-7163 xfs_buf_lock_done: hold 2 lock 0 flags ASYNC
mount-7163 xfs_buf_unlock: hold 2 lock 1 flags ASYNC
This is an async write that is completing, so there's nobody waiting
for it directly. Hence we call xfs_buf_relse() once all the
processing is complete. That does:
Now, it's clear that mount is waiting on the buffer lock, and that
it has been released by xfs_buf_relse() and gained by mount. This is
expected, because at this point the mount process is in
xfs_buf_delwri_submit() waiting for all the IO it submitted to
complete.
The mount process, however, is waiting on the lock for the buffer
because it is in xfs_buf_delwri_submit(). This waits for IO
completion, but it doesn't wait for the buffer reference owned by
the IO to go away. The mount process collects all the completions,
fails the log recovery, and the higher level code then calls
xfs_wait_buftarg() to free all the remaining buffers in the
filesystem.
The issue is that on unlocking the buffer, the scheduler has decided
that the mount process has higher priority than the the kworker
thread that is running the IO completion, and so immediately
switched contexts to the mount process from the semaphore unlock
code, hence preventing the kworker thread from finishing the IO
completion and releasing the IO reference to the buffer.
Hence by the time that xfs_wait_buftarg() is run, the buffer still
has an active reference and so isn't on the LRU list that the
function walks to free the remaining buffers. Hence we miss that
buffer and continue onwards to tear down the mount structures,
at which time we get find a stray reference count on the perag
structure. On a non-debug kernel, this will be ignored and the
structure torn down and freed. Hence when the kworker thread is then
rescheduled and the buffer released and freed, it will access a
freed perag structure.
The problem here is that when the log mount fails, we still need to
quiesce the log to ensure that the IO workqueues have returned to
idle before we run xfs_wait_buftarg(). By synchronising the
workqueues, we ensure that all IO completions are fully processed,
not just to the point where buffers have been unlocked. This ensures
we don't end up in the situation above.
cc: <stable@vger.kernel.org> # 3.18 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 4126014e7cd0d5e667953610139b20388910cbbd)
Hash implementations that require a key may crash if you use
them without setting a key. This patch adds the necessary checks
so that if you do attempt to use them without a key that we return
-ENOKEY instead of proceeding.
This patch also adds a compatibility path to support old applications
that do acept(2) before setkey.
Cc: stable@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit e1ed9a4b4380fc33c558a0c1bd7cbf527e891151)
Commit c1af244e143b4010401d70ba504c927196c75077 ("crypto: hash - Add
crypto_ahash_has_setkey") added an element "bool has_setkey" to the
crypto_ahash structure. This element was added in a place where
there had been a "hole" in the structure, so the change affected
neither the offsets of the other elements nor the overall size of
the structure.
This commit wraps the new element in "#ifndef __GENKSYMS__" to hide
it from the kABI checker.
Each af_alg parent socket obtained by socket(2) corresponds to a
tfm object once bind(2) has succeeded. An accept(2) call on that
parent socket creates a context which then uses the tfm object.
Therefore as long as any child sockets created by accept(2) exist
the parent socket must not be modified or freed.
This patch guarantees this by using locks and a reference count
on the parent socket. Any attempt to modify the parent socket will
fail with EBUSY.
Cc: stable@vger.kernel.org Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 0571ba52a19e18a1c20469454231eef681cb1310)
@console_may_schedule tracks whether console_sem was acquired through
lock or trylock. If the former, we're inside a sleepable context and
console_conditional_schedule() performs cond_resched(). This allows
console drivers which use console_lock for synchronization to yield
while performing time-consuming operations such as scrolling.
However, the actual console outputting is performed while holding
irq-safe logbuf_lock, so console_unlock() clears @console_may_schedule
before starting outputting lines. Also, only a few drivers call
console_conditional_schedule() to begin with. This means that when a
lot of lines need to be output by console_unlock(), for example on a
console registration, the task doing console_unlock() may not yield for
a long time on a non-preemptible kernel.
If this happens with a slow console devices, for example a serial
console, the outputting task may occupy the cpu for a very long time.
Long enough to trigger softlockup and/or RCU stall warnings, which in
turn pile more messages, sometimes enough to trigger the next cycle of
warnings incapacitating the system.
Fix it by making console_unlock() insert cond_resched() between lines if
@console_may_schedule.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Calvin Owens <calvinowens@fb.com> Acked-by: Jan Kara <jack@suse.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Kyle McMartin <kyle@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit bc24ac15b0746172a8f603171352aa54abcf7c78)
Commit 08d78658f393 ("panic: release stale console lock to always get the
logbuf printed out") introduced an unwanted bad unlock balance report when
panic() is called directly and not from OOPS (e.g. from out_of_memory()).
The difference is that in case of OOPS we disable locks debug in
oops_enter() and on direct panic call nobody does that.
Fixes: 08d78658f393 ("panic: release stale console lock to always get the logbuf printed out") Reported-by: kernel test robot <ying.huang@linux.intel.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Baoquan He <bhe@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Xie XiuQi <xiexiuqi@huawei.com> Cc: Seth Jennings <sjenning@redhat.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Jan Kara <jack@suse.cz> Cc: Petr Mladek <pmladek@suse.cz> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 0e19e24c3fe0abde8e2c5f4543616a251ccea6bf)
In some cases we may end up killing the CPU holding the console lock
while still having valuable data in logbuf. E.g. I'm observing the
following:
- A crash is happening on one CPU and console_unlock() is being called on
some other.
- console_unlock() tries to print out the buffer before releasing the lock
and on slow console it takes time.
- in the meanwhile crashing CPU does lots of printk()-s with valuable data
(which go to the logbuf) and sends IPIs to all other CPUs.
- console_unlock() finishes printing previous chunk and enables interrupts
before trying to print out the rest, the CPU catches the IPI and never
releases console lock.
This is not the only possible case: in VT/fb subsystems we have many other
console_lock()/console_unlock() users. Non-masked interrupts (or
receiving NMI in case of extreme slowness) will have the same result.
Getting the whole console buffer printed out on crash should be top
priority.
A spare array holding mem cgroup threshold events is kept around to make
sure we can always safely deregister an event and have an array to store
the new set of events in.
In the scenario where we're going from 1 to 0 registered events, the
pointer to the primary array containing 1 event is copied to the spare
slot, and then the spare slot is freed because no events are left.
However, it is freed before calling synchronize_rcu(), which means
readers may still be accessing threshold->primary after it is freed.
Fixed by only freeing after synchronize_rcu().
Signed-off-by: Martijn Coenen <maco@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 2c641f5b0c8e87d43235ce39890bcc4d0c7cd2fb)
I saw the following BUG_ON triggered in a testcase where a process calls
madvise(MADV_SOFT_OFFLINE) on thps, along with a background process that
calls migratepages command repeatedly (doing ping-pong among different
NUMA nodes) for the first process:
The root cause resides in get_any_page() which retries to get a refcount
of the page to be soft-offlined. This function calls
put_hwpoison_page(), expecting that the target page is putback to LRU
list. But it can be also freed to buddy. So the second check need to
care about such case.
Fixes: af8fae7c0886 ("mm/memory-failure.c: clean up soft_offline_page()") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Steve Capper <steve.capper@linaro.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> [3.9+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 4ae0f4a619e2071dc184e0792d90ace3fd18c280)
When we're using LZ4 multi compression streams for zram swap, we found
out page allocation failure message in system running test. That was
not only once, but a few(2 - 5 times per test). Also, some failure
cases were continually occurring to try allocation order 3.
In order to make parallel compression private data, we should call
kzalloc() with order 2/3 in runtime(lzo/lz4). But if there is no order
2/3 size memory to allocate in that time, page allocation fails. This
patch makes to use vmalloc() as fallback of kmalloc(), this prevents
page alloc failure warning.
After using this, we never found warning message in running test, also
It could reduce process startup latency about 60-120ms in each case.
We can end up allocating a new compression stream with GFP_KERNEL from
within the IO path, which may result is nested (recursive) IO
operations. That can introduce problems if the IO path in question is a
reclaimer, holding some locks that will deadlock nested IOs.
Allocate streams and working memory using GFP_NOIO flag, forbidding
recursive IO and FS operations.
An example:
inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage.
git/20158 [HC0[0]:SC0[0]:HE1:SE1] takes:
(jbd2_handle){+.+.?.}, at: start_this_handle+0x4ca/0x555
{IN-RECLAIM_FS-W} state was registered at:
__lock_acquire+0x8da/0x117b
lock_acquire+0x10c/0x1a7
start_this_handle+0x52d/0x555
jbd2__journal_start+0xb4/0x237
__ext4_journal_start_sb+0x108/0x17e
ext4_dirty_inode+0x32/0x61
__mark_inode_dirty+0x16b/0x60c
iput+0x11e/0x274
__dentry_kill+0x148/0x1b8
shrink_dentry_list+0x274/0x44a
prune_dcache_sb+0x4a/0x55
super_cache_scan+0xfc/0x176
shrink_slab.part.14.constprop.25+0x2a2/0x4d3
shrink_zone+0x74/0x140
kswapd+0x6b7/0x930
kthread+0x107/0x10f
ret_from_fork+0x3f/0x70
irq event stamp: 138297
hardirqs last enabled at (138297): debug_check_no_locks_freed+0x113/0x12f
hardirqs last disabled at (138296): debug_check_no_locks_freed+0x33/0x12f
softirqs last enabled at (137818): __do_softirq+0x2d3/0x3e9
softirqs last disabled at (137813): irq_exit+0x41/0x95
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(jbd2_handle);
<Interrupt>
lock(jbd2_handle);
We have found that migration source will trigger a BUG that the refcount
of mle is already zero before put when the target is down during
migration. The situation is as follows:
dlm_migrate_lockres
dlm_add_migration_mle
dlm_mark_lockres_migrating
dlm_get_mle_inuse
<<<<<< Now the refcount of the mle is 2.
dlm_send_one_lockres and wait for the target to become the
new master.
<<<<<< o2hb detect the target down and clean the migration
mle. Now the refcount is 1.
dlm_migrate_lockres woken, and put the mle twice when found the target
goes down which trigger the BUG with the following message:
"ERROR: bad mle: ".
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 8467278d965a3c2c2f2e95c8eb723f47b872ad5d)
In some cases tmp_bug can be not filled in cifs_filldir and stay uninitialized,
therefore its printk with "%s" modifier can leak content of kernelspace memory.
If old content of this buffer does not contain '\0' access bejond end of
allocated object can crash the host.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Steve French <sfrench@localhost.localdomain> CC: Stable <stable@vger.kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit c5882812d2e1ab7db5bc71a1bca90b3a2d89dedd)
cifs_call_async() queues the MID to the pending list and calls
smb_send_rqst(). If smb_send_rqst() performs a partial send, it sets
the tcpStatus to CifsNeedReconnect and returns an error code to
cifs_call_async(). In this case, cifs_call_async() removes the MID
from the list and returns to the caller.
However, cifs_call_async() releases the server mutex _before_ removing
the MID. This means that a cifs_reconnect() can race with this function
and manage to remove the MID from the list and delete the entry before
cifs_call_async() calls cifs_delete_mid(). This leads to various
crashes due to the use after free in cifs_delete_mid().
Fix this by removing the MID in cifs_call_async() before releasing the
srv_mutex. Also hold the srv_mutex in cifs_reconnect() until the MIDs
are moved out of the pending list.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com> Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <sfrench@localhost.localdomain> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 99b79b15df4ed1a6293cff487b46efc86bd20ae5)
Under some conditions, CIFS can repeatedly call the cifs_dbg() logging
wrapper. If done rapidly enough, the console framebuffer can softlockup
or "rcu_sched self-detected stall". Apply the built-in log ratelimiters
to prevent such hangs.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com> Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit ca7342a8a39704670c4079aacbd78e360beaf223)
In balloon_page_dequeue, pages_lock should cover the loop
(ie, list_for_each_entry_safe). Otherwise, the cursor page could
be isolated by compaction and then list_del by isolation could
poison the page->lru.{prev,next} so the loop finally could
access wrong address like this. This patch fixes the bug.
Cc: <stable@vger.kernel.org> Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit c1a7154c7e5d81bba4b027d42ec1f16113992415)
During my compaction-related stuff, I encountered a bug
with ballooning.
With repeated inflating and deflating cycle, guest memory(
ie, cat /proc/meminfo | grep MemTotal) is decreased and
couldn't be recovered.
The reason is balloon_lock doesn't cover release_pages_balloon
so struct virtio_balloon fields could be overwritten by race
of fill_balloon(e,g, vb->*pfns could be critical).
This patch fixes it in my test.
Cc: <stable@vger.kernel.org> Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 3bbe9868ba5654df63f9e10766620f813e92fdf8)
and rename it to release_pages_balloon. The function originally takes
arrays of pfns and now it takes pointer to struct virtio_ballon.
This change is necessary to conditionally call adjust_managed_page_count
in the next patch.
Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 7daaedba8fa87ade25763e15e5218c66558634c3)
When there is an error copying a chunk dm-snapshot can incorrectly hold
associated bios indefinitely, resulting in hung IO.
The function copy_callback sets pe->error if there was error copying the
chunk, and then calls complete_exception. complete_exception calls
pending_complete on error, otherwise it calls commit_exception with
commit_callback (and commit_callback calls complete_exception).
The persistent exception store (dm-snap-persistent.c) assumes that calls
to prepare_exception and commit_exception are paired.
persistent_prepare_exception increases ps->pending_count and
persistent_commit_exception decreases it.
If there is a copy error, persistent_prepare_exception is called but
persistent_commit_exception is not. This results in the variable
ps->pending_count never returning to zero and that causes some pending
exceptions (and their associated bios) to be held forever.
Fix this by unconditionally calling commit_exception regardless of
whether the copy was successful. A new "valid" parameter is added to
commit_exception -- when the copy fails this parameter is set to zero so
that the chunk that failed to copy (and all following chunks) is not
recorded in the snapshot store. Also, remove commit_callback now that
it is merely a wrapper around pending_complete.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 27f8627c3a656409f8594e3d976d03ab445d7fcc)
Another iscsi target that cannot handle large IOs, but does not tell us
a limit.
The Synology iSCSI targets report:
Block limits VPD page (SBC):
Write same no zero (WSNZ): 0
Maximum compare and write length: 0 blocks
Optimal transfer length granularity: 0 blocks
Maximum transfer length: 0 blocks
Optimal transfer length: 0 blocks
Maximum prefetch length: 0 blocks
Maximum unmap LBA count: 0
Maximum unmap block descriptor count: 0
Optimal unmap granularity: 0
Unmap granularity alignment valid: 0
Unmap granularity alignment: 0
Maximum write same length: 0x0 blocks
and the size of the command it can handle seems to depend on how much
memory it can allocate at the time. This results in IO errors when
handling large IOs. This patch just has us use the old 1024 default
sectors for this target by adding it to the scsi blacklist. We do not
have good contacs with this vendors, so I have not been able to try and
fix on their side.
I have posted this a long while back, but it was not merged. This
version just fixes it up for merge/patch failures in the original
version.
Reported-by: Ancoron Luciferis <ancoron.luciferis@googlemail.com> Reported-by: Michael Meyers <steltek@tcnnet.com> Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: <stable@vger.kernel.org> # 4.1+ Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 9d8246cd71ec50f8aa57c1ea74d8aff314908043)
Dmitry reported that he was able to reproduce the WARN_ON_ONCE that
fires in locks_free_lock_context when the flc_posix list isn't empty.
The problem turns out to be that we're basically rebuilding the
file_lock from scratch in fcntl_setlk when we discover that the setlk
has raced with a close. If the l_whence field is SEEK_CUR or SEEK_END,
then we may end up with fl_start and fl_end values that differ from
when the lock was initially set, if the file position or length of the
file has changed in the interim.
Fix this by just reusing the same lock request structure, and simply
override fl_type value with F_UNLCK as appropriate. That ensures that
we really are unlocking the lock that was initially set.
While we're there, make sure that we do pop a WARN_ON_ONCE if the
removal ever fails. Also return -EBADF in this event, since that's
what we would have returned if the close had happened earlier.
Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Fixes: c293621bbf67 (stale POSIX lock handling) Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Acked-by: "J. Bruce Fields" <bfields@fieldses.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 2e21928b854d0201e5af8413daaa8dfe1b32690d)
We can handle the special case of num_stripes == 0 directly inside
btrfs_read_sys_array. The BUG_ON in btrfs_chunk_item_size is there to
catch other unhandled cases where we fail to validate external data.
A crafted or corrupted image crashes at mount time:
Commit 36e097a8a297 ("PCI: Split out bridge window override of minimum
allocation address") claimed to do no functional changes but unfortunately
did: The "min" variable is altered. At least the AVM A1 PCMCIA adapter was
no longer detected, breaking ISDN operation.
Use a local copy of "min" to restore the previous behaviour.
[bhelgaas: avoid gcc "?:" extension for portability and readability] Fixes: 36e097a8a297 ("PCI: Split out bridge window override of minimum allocation address") Signed-off-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.14+ Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 24ab3b8e796248bfbdb8a80469b9811b5df39caa)
If a name contains at least some characters with Unicode values
exceeding single byte, the CS0 output should have 2 bytes per character.
And if other input characters have single byte Unicode values, then
the single input byte is converted to 2 output bytes, and the length
of output becomes larger than the length of input. And if the input
name is long enough, the output length may exceed the allocated buffer
length.
All this means that conversion from UTF8 or NLS to CS0 requires
checking of output length in order to stop when it exceeds the given
output buffer size.
[JK: Make code return -ENAMETOOLONG instead of silently truncating the
name]
CC: stable@vger.kernel.org Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 516a102b0add0610805d0062670b18b1b44ccdda)
udf_CS0toUTF8 function stops the conversion when the output buffer
length reaches UDF_NAME_LEN-2, which is correct maximum name length,
but, when checking, it leaves the space for a single byte only,
while multi-bytes output characters can take more space, causing
buffer overflow.
Similar error exists in udf_CS0toNLS function, that restricts
the output length to UDF_NAME_LEN, while actual maximum allowed
length is UDF_NAME_LEN-2.
In these cases the output can override not only the current buffer
length field, causing corruption of the name buffer itself, but also
following allocation structures, causing kernel crash.
Adjust the output length checks in both functions to prevent buffer
overruns in case of multi-bytes UTF8 or NLS characters.
CC: stable@vger.kernel.org Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit d6341753c418d3699948290d8c0b9d9dc78bd209)
Fix the below Oops when trying to modprobe wlcore_spi.
The oops occurs because the wl1271_power_{off,on}()
function doesn't check the power() function pointer.
[ 23.665030] [<bf2581f0>] (wl12xx_set_power_on [wlcore]) from
[<bf25f7ac>] (wlcore_nvs_cb+0x118/0xa4c [wlcore])
[ 23.675604] [<bf25f7ac>] (wlcore_nvs_cb [wlcore]) from [<c04387ec>]
(request_firmware_work_func+0x30/0x58)
[ 23.685784] [<c04387ec>] (request_firmware_work_func) from
[<c0058e2c>] (process_one_work+0x1b4/0x4b4)
[ 23.695591] [<c0058e2c>] (process_one_work) from [<c0059168>]
(worker_thread+0x3c/0x4a4)
[ 23.704124] [<c0059168>] (worker_thread) from [<c005ee68>]
(kthread+0xd4/0xf0)
[ 23.711747] [<c005ee68>] (kthread) from [<c000f598>]
(ret_from_fork+0x14/0x3c)
[ 23.719357] Code: bad PC value
[ 23.722760] ---[ end trace 981be8510db9b3a9 ]---
Prevent oops by validationg power() pointer value before
calling the function.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Cc: stable@vger.kernel.org Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 34ed7459a09569f4b2dd8a549f420fac8c3619e0)
Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.
This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.
But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit ebd138117e5be089d0e10fea7cb308e8345ed643)
Added a safeguard in the shutdown case. At least while not being
attached it is also possible to trigger a kernel bug by writing into
writeback_running. This change adds the same check before trying to
wake up the thread for that case.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit ad148665b58dcd0a4336188ce4a2194d7f353c5f)
Allows to use register, not register_quiet in udev to avoid "device_busy" error.
The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis
<g2p.code@gmail.com> does not unlock the mutex and hangs the kernel.
See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion.
Cc: Denis Bychkov <manover@gmail.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Gabriel de Perthuis <g2p.code@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit d5402134c27d66e83295ae2961772b89bc6a50bc)
We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach()
function when we attach a backing device first time. After detaching this
backing device, this flag will be true and sysfs_remove_link() isn't called in
bcache_device_unlink(). Then when we attach this backing device again,
sysfs_create_link() will return EEXIST error in bcache_device_link().
So the fix is trival and we clear this flag in bcache_device_link().
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Tested-by: Joshua Schmid <jschmid@suse.com> Tested-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Kent Overstreet <kmo@daterainc.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 14dca8988999b6ccf4126cf6a3455e5822777a8f)
Subject : [PATCH v2] bcache: fix a livelock in btree lock
Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM)
This commit tries to fix a livelock in bcache. This livelock might
happen when we causes a huge number of cache misses simultaneously.
When we get a cache miss, bcache will execute the following path.
->cached_dev_make_request()
->cached_dev_read()
->cached_lookup()
->bch->btree_map_keys()
->btree_root() <------------------------
->bch_btree_map_keys_recurse() |
->cache_lookup_fn() |
->cached_dev_cache_miss() |
->bch_btree_insert_check_key() -|
[If btree->seq is not equal to seq + 1, we should return
EINTR and traverse btree again.]
In bch_btree_insert_check_key() function we first need to check upgrade
flag (op->lock == -1), and when this flag is true we need to release
read btree->lock and try to take write btree->lock. During taking and
releasing this write lock, btree->seq will be monotone increased in
order to prevent other threads modify this in cache miss (see btree.h:74).
But if there are some cache misses caused by some requested, we could
meet a livelock because btree->seq is always changed by others. Thus no
one can make progress.
This commit will try to take write btree->lock if it encounters a race
when we traverse btree. Although it sacrifice the scalability but we
can ensure that only one can modify the btree.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Tested-by: Joshua Schmid <jschmid@suse.com> Tested-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Joshua Schmid <jschmid@suse.com> Cc: Zhu Yanhai <zhu.yanhai@gmail.com> Cc: Kent Overstreet <kmo@daterainc.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit c505638900d191ae10d1f8afdc8d09ca8c2de0d4)
If a NFSv4 client uses the cache_consistency_bitmask in order to
request only information about the change attribute, timestamps and
size, then it has not revalidated all attributes, and hence the
attribute timeout timestamp should not be updated.
Reported-by: Donald Buczek <buczek@molgen.mpg.de> Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit 8572f2fa313c47750609178b20caf0598fd1042a)
We've seen this in a packet capture - I've intermixed what I
think was going on. The fix here is to grab the so_lock sooner.
1964379 -> #1 open (for write) reply seqid=1 1964393 -> #2 open (for read) reply seqid=2
__nfs4_close(), state->n_wronly--
nfs4_state_set_mode_locked(), changes state->state = [R]
state->flags is [RW]
state->state is [R], state->n_wronly == 0, state->n_rdonly == 1
1964398 -> #3 open (for write) call -> because close is already running 1964399 -> downgrade (to read) call seqid=2 (close of #1) 1964402 -> #3 open (for write) reply seqid=3
__update_open_stateid()
nfs_set_open_stateid_locked(), changes state->flags
state->flags is [RW]
state->state is [R], state->n_wronly == 0, state->n_rdonly == 1
new sequence number is exposed now via nfs4_stateid_copy()
next step would be update_open_stateflags(), pending so_lock
1964403 -> downgrade reply seqid=2, fails with OLD_STATEID (close of #1)
nfs4_close_prepare() gets so_lock and recalcs flags -> send close
The driver allocates the spinlock but fails to initialize it correctly.
The kernel reports a BUG indicating bad spinlock magic when spinlock
debugging is enabled.
Call spin_lock_init() on it to initialize it correctly.
udf_next_aext() just follows extent pointers while extents are marked as
indirect. This can loop forever for corrupted filesystem. Limit number
the of indirect extents we are willing to follow in a row.
[JK: Updated changelog, limit, style]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: stable@vger.kernel.org Cc: Jan Kara <jack@suse.com> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 4476dc677064d27c1fb6ff28a47eeac384e8ba64)
If the proxy lock in the requeue loop acquires the rtmutex for a
waiter then it acquired also refcount on the pi_state related to the
futex, but the waiter side does not drop the reference count.
Add the missing free_pi_state() call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Darren Hart <darren@dvhart.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Bhuvanesh_Surachari@mentor.com Cc: Andy Lowe <Andy_Lowe@mentor.com> Link: http://lkml.kernel.org/r/20151219200607.178132067@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit e70aade221a271f91e2d71901b2d602df2faee15)
When a thin pool is being destroyed delayed work items are
cancelled using cancel_delayed_work(), which doesn't guarantee that on
return the delayed item isn't running. This can cause the work item to
requeue itself on an already destroyed workqueue. Fix this by using
cancel_delayed_work_sync() which guarantees that on return the work item
is not running anymore.
Fixes: 905e51b39a555 ("dm thin: commit outstanding data every second") Fixes: 85ad643b7e7e5 ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 9e612a000cf889cfa624d984ccef770fdce43cf6)
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
I get the splat below when modprobing/rmmoding EDAC drivers. It happens
because bus->name is invalid after bus_unregister() has run. The Code: section
below corresponds to:
This patch fixes kernel crash at removing directory which contains
whiteouts from lower layers.
Cache of directory content passed as "list" contains entries from all
layers, including whiteouts from lower layers. So, lookup in upper dir
(moved into work at this stage) will return negative entry. Plus this
cache is filled long before and we can race with external removal.
Example:
mkdir -p lower0/dir lower1/dir upper work overlay
touch lower0/dir/a lower0/dir/b
mknod lower1/dir/a c 0 0
mount -t overlay none overlay -o lowerdir=lower1:lower0,upperdir=upper,workdir=work
rm -fr overlay/dir
The maximum chunks used by the function is
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE + 1).
The original commands array had space for
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) commands.
When the last chunk is used (len > 4 * WSPI_MAX_CHUNK_SIZE), the last
command is stored outside the bounds of the commands array.
Oops 5 (page fault) is generated during current wl1271 firmware load
attempt:
root@debian-armhf:~# ifconfig wlan0 up
[ 294.312399] Unable to handle kernel paging request at virtual address 00203fc4
[ 294.320173] pgd = de528000
[ 294.323028] [00203fc4] *pgd=00000000
[ 294.326916] Internal error: Oops: 5 [#1] SMP ARM
[ 294.331789] Modules linked in: bnep rfcomm bluetooth ipv6 arc4 wl12xx
wlcore mac80211 musb_dsps cfg80211 musb_hdrc usbcore usb_common
wlcore_spi omap_rng rng_core musb_am335x omap_wdt cpufreq_dt thermal_sys
hwmon
[ 294.351838] CPU: 0 PID: 1827 Comm: ifconfig Not tainted 4.2.0-00002-g3e9ad27-dirty #78
[ 294.360154] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 294.366557] task: dc9d6d40 ti: de550000 task.ti: de550000
[ 294.372236] PC is at __spi_validate+0xa8/0x2ac
[ 294.376902] LR is at __spi_sync+0x78/0x210
[ 294.381200] pc : [<c049c760>] lr : [<c049ebe0>] psr: 60000013
[ 294.381200] sp : de551998 ip : de5519d8 fp : 00200000
[ 294.393242] r10: de551c8c r9 : de5519d8 r8 : de3a9000
[ 294.398730] r7 : de3a9258 r6 : de3a9400 r5 : de551a48 r4 : 00203fbc
[ 294.405577] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : de3a9000
[ 294.412420] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 294.419918] Control: 10c5387d Table: 9e528019 DAC: 00000015
[ 294.425954] Process ifconfig (pid: 1827, stack limit = 0xde550218)
[ 294.432437] Stack: (0xde551998 to 0xde552000)
...
[ 294.883613] [<c049c760>] (__spi_validate) from [<c049ebe0>]
(__spi_sync+0x78/0x210)
[ 294.891670] [<c049ebe0>] (__spi_sync) from [<bf036598>]
(wl12xx_spi_raw_write+0xfc/0x148 [wlcore_spi])
[ 294.901661] [<bf036598>] (wl12xx_spi_raw_write [wlcore_spi]) from
[<bf21c694>] (wlcore_boot_upload_firmware+0x1ec/0x458 [wlcore])
[ 294.914038] [<bf21c694>] (wlcore_boot_upload_firmware [wlcore]) from
[<bf24532c>] (wl12xx_boot+0xc10/0xfac [wl12xx])
[ 294.925161] [<bf24532c>] (wl12xx_boot [wl12xx]) from [<bf20d5cc>]
(wl1271_op_add_interface+0x5b0/0x910 [wlcore])
[ 294.936364] [<bf20d5cc>] (wl1271_op_add_interface [wlcore]) from
[<bf15c4ac>] (ieee80211_do_open+0x44c/0xf7c [mac80211])
[ 294.947963] [<bf15c4ac>] (ieee80211_do_open [mac80211]) from
[<c0537978>] (__dev_open+0xa8/0x110)
[ 294.957307] [<c0537978>] (__dev_open) from [<c0537bf8>]
(__dev_change_flags+0x88/0x148)
[ 294.965713] [<c0537bf8>] (__dev_change_flags) from [<c0537cd0>]
(dev_change_flags+0x18/0x48)
[ 294.974576] [<c0537cd0>] (dev_change_flags) from [<c05a55a0>]
(devinet_ioctl+0x6b4/0x7d0)
[ 294.983191] [<c05a55a0>] (devinet_ioctl) from [<c0517040>]
(sock_ioctl+0x1e4/0x2bc)
[ 294.991244] [<c0517040>] (sock_ioctl) from [<c017d378>]
(do_vfs_ioctl+0x420/0x6b0)
[ 294.999208] [<c017d378>] (do_vfs_ioctl) from [<c017d674>]
(SyS_ioctl+0x6c/0x7c)
[ 295.006880] [<c017d674>] (SyS_ioctl) from [<c000f4c0>]
(ret_fast_syscall+0x0/0x54)
[ 295.014835] Code: e1550004e24440340a00007de5953018 (e5942008)
[ 295.021544] ---[ end trace 66ed188198f4e24e ]---
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 3d51d36e7148182e76fc36d66c494d192c410fdd)
Free skb for received frames with a wrong checksum. This can happen
pretty rapidly, exhausting all memory.
This fixes a memleak (detected with kmemleak). Originally found while
using monitor mode, but it also appears during managed mode (once the
link is up).
Cc: stable@vger.kernel.org Signed-off-by: Peter Wu <peter@lekensteyn.nl> ACKed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 76e8046ae4f3c7abd9e4f8ab69000609e554eb77)
1e75fa8 "time: Condense timekeeper.xtime into xtime_sec" replaced a call to
clocksource_cyc2ns() from timekeeping_get_ns() with an open-coded version
of the same logic to avoid keeping a semi-redundant struct timespec
in struct timekeeper.
However, the commit also introduced a subtle semantic change - where
clocksource_cyc2ns() uses purely unsigned math, the new version introduces
a signed temporary, meaning that if (delta * tk->mult) has a 63-bit
overflow the following shift will still give a negative result. The
choice of 'maxsec' in __clocksource_updatefreq_scale() means this will
generally happen if there's a ~10 minute pause in examining the
clocksource.
This can be triggered on a powerpc KVM guest by stopping it from qemu for
a bit over 10 minutes. After resuming time has jumped backwards several
minutes causing numerous problems (jiffies does not advance, msleep()s can
be extended by minutes..). It doesn't happen on x86 KVM guests, because
the guest TSC is effectively frozen while the guest is stopped, which is
not the case for the powerpc timebase.
Obviously an unsigned (64 bit) overflow will only take twice as long as a
signed, 63-bit overflow. I don't know the time code well enough to know
if that will still cause incorrect calculations, or if a 64-bit overflow
is avoided elsewhere.
Still, an incorrect forwards clock adjustment will cause less trouble than
time going backwards. So, this patch removes the potential for
intermediate signed overflow.
Cc: stable@vger.kernel.org (3.7+) Suggested-by: Laurent Vivier <lvivier@redhat.com> Tested-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 51975a203210d3a94a7711651b1045ed0e3514ed)
v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:
Sure, it's better to bail out of past-the-eof read and return 0 than return
a bogus negative value on such. Only we'd better make sure we are bailing out
with 0 and not -ENOMEM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 57b7d61c2d89e3e0665b9cdcc8fb73b08d10f0c2)
Assume a filesystem with 4KB blocks. When a file has size 1000 bytes and
we issue direct IO read at offset 1024, blockdev_direct_IO() reads the
tail of the last block and the logic for handling short DIO reads in
dio_complete() results in a return value -24 (1000 - 1024) which
obviously confuses userspace.
Fix the problem by bailing out early once we sample i_size and can
reliably check that direct IO read starts beyond i_size.
Reported-by: Avi Kivity <avi@scylladb.com> Fixes: 9fe55eea7e4b444bafc42fa0000cc2d1d2847275 CC: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 8885e7f3d76a9d42eb4fd97a3cfc5a8ac7f6f2ff)
The vivid_fb_ioctl() code fails to initialize the 16 _reserved bytes of
struct fb_vblank after the ->hcount member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.
Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;] Cc: Jiri Kosina <jikos@kernel.org> Cc: linux-input@vger.kernel.org Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b50a2b556d1e487c2430e13042a98325adca0be5)
Remove the dst_entries_init/destroy calls for xfrm4 and xfrm6 dst_ops
templates; their dst_entries counters will never be used. Move the
xfrm dst_ops initialization from the common xfrm/xfrm_policy.c to
xfrm4/xfrm4_policy.c and xfrm6/xfrm6_policy.c, and call dst_entries_init
and dst_entries_destroy for each net namespace.
The ipv4 and ipv6 xfrms each create dst_ops template, and perform
dst_entries_init on the templates. The template values are copied to each
net namespace's xfrm.xfrm*_dst_ops. The problem there is the dst_ops
pcpuc_entries field is a percpu counter and cannot be used correctly by
simply copying it to another object.
The result of this is a very subtle bug; changes to the dst entries
counter from one net namespace may sometimes get applied to a different
net namespace dst entries counter. This is because of how the percpu
counter works; it has a main count field as well as a pointer to the
percpu variables. Each net namespace maintains its own main count
variable, but all point to one set of percpu variables. When any net
namespace happens to change one of the percpu variables to outside its
small batch range, its count is moved to the net namespace's main count
variable. So with multiple net namespaces operating concurrently, the
dst_ops entries counter can stray from the actual value that it should
be; if counts are consistently moved from one net namespace to another
(which my testing showed is likely), then one net namespace winds up
with a negative dst_ops count while another winds up with a continually
increasing count, eventually reaching its gc_thresh limit, which causes
all new traffic on the net namespace to fail with -ENOBUFS.
Signed-off-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit eeca98948d8c4922e6deb16bfc9ee0bd9902dbb0)
A case can occur when sctp_accept() is called by the user during
a heartbeat timeout event after the 4-way handshake. Since
sctp_assoc_migrate() changes both assoc->base.sk and assoc->ep, the
bh_sock_lock in sctp_generate_heartbeat_event() will be taken with
the listening socket but released with the new association socket.
The result is a deadlock on any future attempts to take the listening
socket lock.
Note that this race can occur with other SCTP timeouts that take
the bh_lock_sock() in the event sctp_accept() is called.
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
CslRx/12087 is trying to release lock (slock-AF_INET) at:
[<ffffffffa01bcae0>] sctp_generate_timeout_event+0x40/0xe0 [sctp]
but there are no more locks to release!
other info that might help us debug this:
2 locks held by CslRx/12087:
#0: (&asoc->timers[i]){+.-...}, at: [<ffffffff8108ce1f>] run_timer_softirq+0x16f/0x3e0
#1: (slock-AF_INET){+.-...}, at: [<ffffffffa01bcac3>] sctp_generate_timeout_event+0x23/0xe0 [sctp]
Ensure the socket taken is also the same one that is released by
saving a copy of the socket before entering the timeout event
critical section.
Signed-off-by: Karl Heiss <kheiss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit 534e9016cd88ccd577b226b7172e5cd079f5fb02)
We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 490c963c1eb9a7f5f74446f4b9738c9fb1b8e325)
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_node_free_ref.
Fixes: 72822225bd41 ("batman-adv: Fix rcu_barrier() miss due to double call_rcu() in TT code") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 95785b105fa2f784ad7b6be0238338b648ed892a)
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_hardif_free_ref.
Fixes: 89652331c00f ("batman-adv: split tq information in neigh_node struct") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ae3eb44e0e8b4e0fe4ab51e0a91d76517abc1e30)
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_ifinfo_free_ref.
Fixes: 89652331c00f ("batman-adv: split tq information in neigh_node struct") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 924224c6e44a393a2a41385d699230384ea23df5)
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_node_free_ref.
Fixes: 89652331c00f ("batman-adv: split tq information in neigh_node struct") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 620493a90c78ce1bd150d48ca6f624ad964e0c8d)
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_ifinfo_free_ref.
Fixes: 7351a4822d42 ("batman-adv: split out router from orig_node") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 9d188c6b672c7d205f43da74b534d2114371edc5)
The batadv_nc_node_free_ref function uses call_rcu to delay the free of the
batadv_nc_node object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_nc_node also contains a
reference to orig_node which must be removed.
The reference drop of orig_node was done in the call_rcu function
batadv_nc_node_free_rcu but should actually be done in the
batadv_nc_node_release function to avoid nested call_rcus. This is
important because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will
not detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: d56b1705e28c ("batman-adv: network coding - detect coding nodes and remove these after timeout") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 34c5bf7c7bf4e285274e28a36b08cbf3da5bd3e3)
The batadv_claim_free_ref function uses call_rcu to delay the free of the
batadv_bla_claim object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_bla_claim also contains a
reference to backbone_gw which must be removed.
The reference drop of backbone_gw was done in the call_rcu function
batadv_claim_free_rcu but should actually be done in the
batadv_claim_release function to avoid nested call_rcus. This is important
because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will not
detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: 23721387c409 ("batman-adv: add basic bridge loop avoidance code") Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 016cb1d02db9840a62c0e2a465ffd6617eacffc7)
Currently slhc_init() treats out-of-range values of rslots and tslots
as equivalent to 0, except that if tslots is too large it will
dereference a null pointer (CVE-2015-7799).
Add a range-check at the top of the function and make it return an
ERR_PTR() on error instead of NULL. Change the callers accordingly.
Compile-tested only.
Reported-by: 郭永刚 <guoyonggang@360.cn>
References: http://article.gmane.org/gmane.comp.security.oss.general/17908 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a50a93cc99286dc444c7e5ccc7dfb9d58c2d346d)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 5984398539a2c47834caf1b00dc9f58b7bb2e67a)
When creating a timewait socket, we need to arm the timer before
allowing other cpus to find it. The signal allowing cpus to find
the socket is setting tw_refcnt to non zero value.
As we set tw_refcnt in __inet_twsk_hashdance(), we therefore need to
call inet_twsk_schedule() first.
This also means we need to remove tw_refcnt changes from
inet_twsk_schedule() and let the caller handle it.
Note that because we use mod_timer_pinned(), we have the guarantee
the timer wont expire before we set tw_refcnt as we run in BH context.
To make things more readable I introduced inet_twsk_reschedule() helper.
When rearming the timer, we can use mod_timer_pending() to make sure
we do not rearm a canceled timer.
Note: This bug can possibly trigger if packets of a flow can hit
multiple cpus. This does not normally happen, unless flow steering
is broken somehow. This explains this bug was spotted ~5 months after
its introduction.
A similar fix is needed for SYN_RECV sockets in reqsk_queue_hash_req(),
but will be provided in a separate patch for proper tracking.
Fixes: 789f558cfb36 ("tcp/dccp: get rid of central timewait timer") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Ying Cai <ycai@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 479b539a310152b10c1747ac8c5354ed7bc25181)
After promisc mode management was introduced a bridge device could do
dev_set_promiscuity from its ndo_change_rx_flags() callback which in
turn can be called after the bridge's addr_list_lock has been taken
(e.g. by dev_uc_add). This causes a false positive lockdep splat because
the port interfaces' addr_list_lock is taken when br_manage_promisc()
runs after the bridge's addr list lock was already taken.
To remove the false positive introduce a custom bridge addr_list_lock
class and set it on bridge init.
A simple way to reproduce this is with the following:
$ brctl addbr br0
$ ip l add l br0 br0.100 type vlan id 100
$ ip l set br0 up
$ ip l set br0.100 up
$ echo 1 > /sys/class/net/br0/bridge/vlan_filtering
$ brctl addif br0 eth0
Splat:
[ 43.684325] =============================================
[ 43.684485] [ INFO: possible recursive locking detected ]
[ 43.684636] 4.4.0-rc8+ #54 Not tainted
[ 43.684755] ---------------------------------------------
[ 43.684906] brctl/1187 is trying to acquire lock:
[ 43.685047] (_xmit_ETHER){+.....}, at: [<ffffffff8150169e>] dev_set_rx_mode+0x1e/0x40
[ 43.685460] but task is already holding lock:
[ 43.685618] (_xmit_ETHER){+.....}, at: [<ffffffff815072a7>] dev_uc_add+0x27/0x80
[ 43.686015] other info that might help us debug this:
[ 43.686316] Possible unsafe locking scenario:
CC: Vlad Yasevich <vyasevic@redhat.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Bridge list <bridge@lists.linux-foundation.org> CC: Andy Gospodarek <gospo@cumulusnetworks.com> CC: Roopa Prabhu <roopa@cumulusnetworks.com> Fixes: 2796d0c648c9 ("bridge: Automatically manage port promiscuous mode.") Reported-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 332fb8799ed1c701339e9b4dad3efbed245b4cf8)
When a tunnel decapsulates the outer header, it has to comply
with RFC 6080 and eventually propagate CE mark into inner header.
It turns out IP6_ECN_set_ce() does not correctly update skb->csum
for CHECKSUM_COMPLETE packets, triggering infamous "hw csum failure"
messages and stack traces.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2980502b9f6d3e15a4dd6695d4cfff8ec3213209)
projects / users / jedix / linux-maple.git / log