Xin Long [Sat, 1 Apr 2023 23:09:57 +0000 (19:09 -0400)]
sctp: check send stream number after wait_for_sndbuf
This patch fixes a corner case where the asoc out stream count may change
after wait_for_sndbuf.
When the main thread in the client starts a connection, if its out stream
count is set to N while the in stream count in the server is set to N - 2,
another thread in the client keeps sending the msgs with stream number
N - 1, and waits for sndbuf before processing INIT_ACK.
However, after processing INIT_ACK, the out stream count in the client is
shrunk to N - 2, the same to the in stream count in the server. The crash
occurs when the thread waiting for sndbuf is awake and sends the msg in a
non-existing stream(N - 1), the call trace is as below:
The fix is to add an unlikely check for the send stream number after the
thread wakes up from the wait_for_sndbuf.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: syzbot+47c24ca20a2fa01f082e@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Based on further tests, it seems that the QDMA shaper is not able to
perform shaping close to the MAC link rate without throughput loss.
This cannot be compensated by increasing the shaping rate, so it seems
to be an internal limit.
Fix the remaining throughput regression by detecting that condition and
limiting shaping to ports with lower link speed.
This patch intentionally ignores link speed gain from TRGMII, because
even on such links, shaping to 1000 Mbit/s incurs some throughput
degradation.
Fixes: f63959c7eec3 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues") Tested-By: Frank Wunderlich <frank-w@public-files.de> Reported-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: David S. Miller <davem@davemloft.net>
Gustav Ekelund [Fri, 31 Mar 2023 08:40:13 +0000 (10:40 +0200)]
net: dsa: mv88e6xxx: Reset mv88e6393x force WD event bit
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family" Signed-off-by: Gustav Ekelund <gustaek@axis.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 31 Mar 2023 02:21:44 +0000 (19:21 -0700)]
net: don't let netpoll invoke NAPI if in xmit context
Commit 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix") narrowed
down the region under netif_tx_trylock() inside netpoll_send_skb().
(At that point in time netif_tx_trylock() would lock all queues of
the device.) Taking the tx lock was problematic because driver's
cleanup method may take the same lock. So the change made us hold
the xmit lock only around xmit, and expected the driver to take
care of locking within ->ndo_poll_controller().
Unfortunately this only works if netpoll isn't itself called with
the xmit lock already held. Netpoll code is careful and uses
trylock(). The drivers, however, may be using plain lock().
Printing while holding the xmit lock is going to result in rare
deadlocks.
Luckily we record the xmit lock owners, so we can scan all the queues,
the same way we scan NAPI owners. If any of the xmit locks is held
by the local CPU we better not attempt any polling.
It would be nice if we could narrow down the check to only the NAPIs
and the queue we're trying to use. I don't see a way to do that now.
Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Fixes: 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reverted change is required after commit 3948b05950fd ("net: introduce
a config option to tweak MAX_SKB_FRAGS") which does not exist
in this tree, yet. It's only present in -next trees at the time
of writing.
Arseniy Krasnov [Fri, 31 Mar 2023 07:56:41 +0000 (10:56 +0300)]
vsock/vmci: convert VMCI error code to -ENOMEM on send
This adds conversion of VMCI specific error code to general -ENOMEM. It
is needed, because af_vsock.c passes error value returned from transport
to the user, which does not expect to get VMCI_ERROR_* values.
Fixes: c43170b7e157 ("vsock: return errors other than -ENOMEM to socket") Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When playing with various compilers or their versions, some choke on
the t7xx code. For example (with gcc 13):
In file included from ./arch/s390/include/generated/asm/rwonce.h:1,
from ../include/linux/compiler.h:247,
from ../include/linux/build_bug.h:5,
from ../include/linux/bits.h:22,
from ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:17:
In function 'preempt_count',
inlined from 't7xx_fsm_append_event' at ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:439:43:
../include/asm-generic/rwonce.h:44:26: error: array subscript 0 is outside array bounds of 'const volatile int[0]' [-Werror=array-bounds=]
There is no reason for any code in the kernel to be built with -Werror
by default. Note that we have generic CONFIG_WERROR. So if anyone wants
-Werror, they can enable that.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Link: https://lore.kernel.org/all/20230330232717.1f8bf5ea@kernel.org/ Cc: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Cc: Intel Corporation <linuxwwan@intel.com> Cc: Chiranjeevi Rapolu <chiranjeevi.rapolu@linux.intel.com> Cc: Liu Haijun <haijun.liu@mediatek.com> Cc: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Cc: Ricardo Martinez <ricardo.martinez@linux.intel.com> Cc: Loic Poulain <loic.poulain@linaro.org> Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 31 Mar 2023 07:48:56 +0000 (09:48 +0200)]
net: netcp: MAX_SKB_FRAGS is now 'int'
The type of MAX_SKB_FRAGS has changed recently, so the debug printk
needs to be updated:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_create_interface':
drivers/net/ethernet/ti/netcp_core.c:2084:30: error: format '%ld' expects argument of type 'long int', but argument 3 has type 'int' [-Werror=format=]
2084 | dev_err(dev, "tx-pool size too small, must be at least %ld\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3948b05950fd ("net: introduce a config option to tweak MAX_SKB_FRAGS") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Thu, 30 Mar 2023 09:54:42 +0000 (11:54 +0200)]
l2tp: generate correct module alias strings
Commit 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:
Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.
Fixes: 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h") Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390 Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Mar 2023 08:23:41 +0000 (09:23 +0100)]
Merge branch 'phy-handle-fixes'
Michael Sit Wei Hong says:
====================
Fix PHY handle no longer parsing
After the fixed link support was introduced, it is observed that PHY
no longer attach to the MAC properly. So we introduce a helper
function to determine if the MAC should expect to connect to a PHY
and proceed accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Sit Wei Hong [Thu, 30 Mar 2023 09:14:04 +0000 (17:14 +0800)]
net: stmmac: remove redundant fixup to support fixed-link mode
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d95 ("stmmac: intel: prepare to support 1000BASE-X phy interface setting") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Sit Wei Hong [Thu, 30 Mar 2023 09:14:03 +0000 (17:14 +0800)]
net: stmmac: check if MAC needs to attach to a PHY
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf920928 ("net: stmmac: make mdio register skips PHY scanning for fixed-link") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Sit Wei Hong [Thu, 30 Mar 2023 09:14:02 +0000 (17:14 +0800)]
net: phylink: add phylink_expects_phy() method
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use qrtr_node_lock to protect qrtr_node_lookup() implementation, this
is actually improving the protection of node reference.
Fixes: 0a7e0d0ef054 ("net: qrtr: Migrate node lookup tree to spinlock") Reported-by: syzbot+a7492efaa5d61b51db23@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=a7492efaa5d61b51db23 Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bobby Eshleman [Wed, 29 Mar 2023 16:51:58 +0000 (16:51 +0000)]
virtio/vsock: fix leaks due to missing skb owner
This patch sets the skb owner in the recv and send path for virtio.
For the send path, this solves the leak caused when
virtio_transport_purge_skbs() finds skb->sk is always NULL and therefore
never matches it with the current socket. Setting the owner upon
allocation fixes this.
For the recv path, this ensures correctness of accounting and also
correct transfer of ownership in vsock_loopback (when skbs are sent from
one socket and received by another).
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Signed-off-by: Bobby Eshleman <bobby.eshleman@bytedance.com> Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://lore.kernel.org/all/ZCCbATwov4U+GBUv@pop-os.localdomain/ Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 31 Mar 2023 06:44:45 +0000 (23:44 -0700)]
Merge tag 'wireless-2023-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a few fixes:
* fix size calculation for EHT element to put into SKBs
* remove erroneous pre-RCU calls for drivers not using sta_state calls
* fix mesh forwarding and non-forwarding RX
* fix mesh flow dissection
* fix a potential NULL dereference on A-MSDU RX w/o station
* make two variable non-static that really shouldn't be static
* tag 'wireless-2023-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix invalid drv_sta_pre_rcu_remove calls for non-uploaded sta
wifi: mac80211: fix flow dissection for forwarded packets
wifi: mac80211: fix mesh forwarding
wifi: mac80211: fix receiving mesh packets in forwarding=0 networks
wifi: mac80211: fix the size calculation of ieee80211_ie_len_eht_cap()
wifi: mac80211: fix potential null pointer dereference
wifi: mac80211: drop bogus static keywords in A-MSDU rx
====================
Linus Torvalds [Thu, 30 Mar 2023 21:05:21 +0000 (14:05 -0700)]
Merge tag 'net-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from CAN and WPAN.
Still quite a few bugs from this release. This pull is a bit smaller
because major subtrees went into the previous one. Or maybe people
took spring break off?
Current release - regressions:
- phy: micrel: correct KSZ9131RNX EEE capabilities and advertisement
Current release - new code bugs:
- eth: wangxun: fix vector length of interrupt cause
- vsock/loopback: consistently protect the packet queue with
sk_buff_head.lock
- virtio/vsock: fix header length on skb merging
- wpan: ca8210: fix unsigned mac_len comparison with zero
Previous releases - regressions:
- eth: stmmac: don't reject VLANs when IFF_PROMISC is set
- eth: smsc911x: avoid PHY being resumed when interface is not up
- eth: mtk_eth_soc: fix tx throughput regression with direct 1G links
- eth: bnx2x: use the right build_skb() helper after core rework
- wwan: iosm: fix 7560 modem crash on use on unsupported channel
Previous releases - always broken:
- eth: sfc: don't overwrite offload features at NIC reset
- eth: r8169: fix RTL8168H and RTL8107E rx crc error
- can: j1939: prevent deadlock by moving j1939_sk_errqueue()
- virt: vmxnet3: use GRO callback when UPT is enabled
- virt: xen: don't do grant copy across page boundary
- phy: dp83869: fix default value for tx-/rx-internal-delay
- dsa: ksz8: fix multiple issues with ksz8_fdb_dump
- eth: mvpp2: fix classification/RSS of VLAN and fragmented packets
* tag 'net-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (55 commits)
net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow
net: ethernet: mtk_eth_soc: fix L2 offloading with DSA untag offload
net: ethernet: mtk_eth_soc: fix flow block refcounting logic
net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
net: dsa: sync unicast and multicast addresses for VLAN filters too
net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
xen/netback: use same error messages for same errors
test/vsock: new skbuff appending test
virtio/vsock: WARN_ONCE() for invalid state of socket
virtio/vsock: fix header length on skb merging
bnxt_en: Add missing 200G link speed reporting
bnxt_en: Fix typo in PCI id to device description string mapping
bnxt_en: Fix reporting of test result in ethtool selftest
i40e: fix registers dump after run ethtool adapter self test
bnx2x: use the right build_skb() helper
net: ipa: compute DMA pool size properly
net: wwan: iosm: fixes 7560 modem crash
net: ethernet: mtk_eth_soc: fix tx throughput regression with direct 1G links
ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
ice: add profile conflict check for AVF FDIR
...
Linus Torvalds [Thu, 30 Mar 2023 20:58:12 +0000 (13:58 -0700)]
Merge tag 'for-6.3/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix two DM core bugs in the code that handles splitting "abnormal" IO
(discards, write same and secure erase) and issuing that IO to the
correct underlying devices (and offsets within those devices).
* tag 'for-6.3/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix __send_duplicate_bios() to always allow for splitting IO
dm: fix improper splitting for abnormal bios
* tag 'drm-fixes-2023-03-30' of git://anongit.freedesktop.org/drm/drm: (27 commits)
Revert "drm/scheduler: track GPU active time per entity"
Revert "drm/etnaviv: export client GPU usage statistics via fdinfo"
drm/etnaviv: fix reference leak when mmaping imported buffer
drm/amdgpu: allow more APUs to do mode2 reset when go to S4
drm/amd/display: Take FEC Overhead into Timeslot Calculation
drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
drm: test: Fix 32-bit issue in drm_buddy_test
drm: buddy_allocator: Fix buddy allocator init on 32-bit systems
drm/nouveau/kms: Fix backlight registration
drm/i915/perf: Drop wakeref on GuC RC error
drm/i915/dpt: Treat the DPT BO as a framebuffer
drm/i915/gem: Flush lmem contents after construction
drm/i915/tc: Fix the ICL PHY ownership check in TC-cold state
drm/i915: Disable DC states for all commits
drm/i915: Workaround ICL CSC_MODE sticky arming
drm/i915: Add a .color_post_update() hook
drm/i915: Move CSC load back into .color_commit_arm() when PSR is enabled on skl/glk
drm/i915: Split icl_color_commit_noarm() from skl_color_commit_noarm()
drm/i915/pmu: Use functions common with sysfs to read actual freq
accel/ivpu: Fix IPC buffer header status field value
...
Mike Snitzer [Thu, 30 Mar 2023 19:09:29 +0000 (15:09 -0400)]
dm: fix __send_duplicate_bios() to always allow for splitting IO
Commit 7dd76d1feec70 ("dm: improve bio splitting and associated IO
accounting") only called setup_split_accounting() from
__send_duplicate_bios() if a single bio were being issued. But the case
where duplicate bios are issued must call it too.
Otherwise the bio won't be split and resubmitted (via recursion through
block core back to DM) to submit the later portions of a bio (which may
map to an entirely different target).
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Fixes: 7dd76d1feec70 ("dm: improve bio splitting and associated IO accounting") Cc: stable@vger.kernel.org Reported-by: Orange Kao <orange@aiven.io> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Mike Snitzer [Thu, 30 Mar 2023 18:56:38 +0000 (14:56 -0400)]
dm: fix improper splitting for abnormal bios
"Abnormal" bios include discards, write zeroes and secure erase. By no
longer passing the calculated 'len' pointer, commit 7dd06a2548b2 ("dm:
allow dm_accept_partial_bio() for dm_io without duplicate bios") took a
senseless approach to disallowing dm_accept_partial_bio() from working
for duplicate bios processed using __send_duplicate_bios().
It inadvertently and incorrectly stopped the use of 'len' when
initializing a target's io (in alloc_tio). As such the resulting tio
could address more area of a device than it should.
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Before this fix:
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop0: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop1: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
Fixes: 7dd06a2548b2 ("dm: allow dm_accept_partial_bio() for dm_io without duplicate bios") Cc: stable@vger.kernel.org Reported-by: Orange Kao <orange@aiven.io> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Felix Fietkau [Thu, 30 Mar 2023 12:08:40 +0000 (14:08 +0200)]
net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow
The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.
Fixes: 33fc42de3327 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 29 Mar 2023 12:11:17 +0000 (13:11 +0100)]
net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
Reported on the Turris forum, mvneta provokes kernel warnings in the
architecture DMA mapping code when mvneta_setup_txqs() fails to
allocate memory. This happens because when mvneta_cleanup_txqs() is
called in the mvneta_stop() path, we leave pointers in the structure
that have been freed.
Then on mvneta_open(), we call mvneta_setup_txqs(), which starts
allocating memory. On memory allocation failure, mvneta_cleanup_txqs()
will walk all the queues freeing any non-NULL pointers - which includes
pointers that were previously freed in mvneta_stop().
Fix this by setting these pointers to NULL to prevent double-freeing
of the same memory.
Vladimir Oltean [Wed, 29 Mar 2023 15:18:21 +0000 (18:18 +0300)]
net: dsa: sync unicast and multicast addresses for VLAN filters too
If certain conditions are met, DSA can install all necessary MAC
addresses on the CPU ports as FDB entries and disable flooding towards
the CPU (we call this RX filtering).
There is one corner case where this does not work.
ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
ip link set swp0 master br0 && ip link set swp0 up
ip link add link swp0 name swp0.100 type vlan id 100
ip link set swp0.100 up && ip addr add 192.168.100.1/24 dev swp0.100
Traffic through swp0.100 is broken, because the bridge turns on VLAN
filtering in the swp0 port (causing RX packets to be classified to the
FDB database corresponding to the VID from their 802.1Q header), and
although the 8021q module does call dev_uc_add() towards the real
device, that API is VLAN-unaware, so it only contains the MAC address,
not the VID; and DSA's current implementation of ndo_set_rx_mode() is
only for VID 0 (corresponding to FDB entries which are installed in an
FDB database which is only hit when the port is VLAN-unaware).
It's interesting to understand why the bridge does not turn on
IFF_PROMISC for its swp0 bridge port, and it may appear at first glance
that this is a regression caused by the logic in commit 2796d0c648c9
("bridge: Automatically manage port promiscuous mode."). After all,
a bridge port needs to have IFF_PROMISC by its very nature - it needs to
receive and forward frames with a MAC DA different from the bridge
ports' MAC addresses.
While that may be true, when the bridge is VLAN-aware *and* it has a
single port, there is no real reason to enable promiscuity even if that
is an automatic port, with flooding and learning (there is nowhere for
packets to go except to the BR_FDB_LOCAL entries), and this is how the
corner case appears. Adding a second automatic interface to the bridge
would make swp0 promisc as well, and would mask the corner case.
Given the dev_uc_add() / ndo_set_rx_mode() API is what it is (it doesn't
pass a VLAN ID), the only way to address that problem is to install host
FDB entries for the cartesian product of RX filtering MAC addresses and
VLAN RX filters.
Fixes: 7569459a52c9 ("net: dsa: manage flooding on the CPU ports") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230329151821.745752-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Bätz [Wed, 29 Mar 2023 15:01:40 +0000 (12:01 -0300)]
net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.") Signed-off-by: Steffen Bätz <steffen@innosonix.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Vetter [Thu, 30 Mar 2023 16:07:12 +0000 (18:07 +0200)]
Merge tag 'drm-intel-fixes-2023-03-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v6.3-rc5:
- Fix PMU support by reusing functions with sysfs
- Fix a number of issues related to color, PSR and arm/noarm
- Fix state check related to ICL PHY ownership check in TC-cold state
- Flush lmem contents after construction
- Fix hibernate oops related to DPT BO
- Fix perf stream error path wakeref balance
Linus Torvalds [Thu, 30 Mar 2023 16:04:04 +0000 (09:04 -0700)]
Merge tag 'sound-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- A potential deadlock fix for USB-audio, involving some change in
PCM core side
- A regression fix for probes of USB-audio devices with the
vendor-specific PCM format bits
- Two regression fixes for the old YMFPCI driver
- A few HD-audio quirks as usual"
* tag 'sound-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirk for Lenovo ZhaoYang CF4620Z
ALSA: ymfpci: Fix BUG_ON in probe function
ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
ALSA: usb-audio: Fix regression on detection of Roland VS-100
ALSA: hda/realtek: Fix support for Dell Precision 3260
ALSA: usb-audio: Fix recursive locking at XRUN during syncing
ALSA: hda/conexant: Partial revert of a quirk for Lenovo
ALSA: hda/realtek: Add quirks for some Clevo laptops
Linus Torvalds [Thu, 30 Mar 2023 16:00:17 +0000 (09:00 -0700)]
Merge tag 'zonefs-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fixes from Damien Le Moal:
- Make sure to always invalidate the last page of an inode straddling
inode->i_size to avoid data inconsistencies with appended data when
the device zone write granularity does not match the page size.
- Do not propagate iomap -ENOBLK error to userspace and use -EBUSY
instead.
* tag 'zonefs-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Do not propagate iomap_dio_rw() ENOTBLK error to user space
zonefs: Always invalidate last cached page on append write
Lucas Stach [Thu, 30 Mar 2023 15:33:27 +0000 (17:33 +0200)]
Revert "drm/etnaviv: export client GPU usage statistics via fdinfo"
This reverts commit 97804a133c68, as it builds on top of df622729ddbf
("drm/scheduler: track GPU active time per entity") which needs to be
reverted, as it introduces a use-after-free.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Lucas Stach [Fri, 24 Feb 2023 17:21:54 +0000 (18:21 +0100)]
drm/etnaviv: fix reference leak when mmaping imported buffer
drm_gem_prime_mmap() takes a reference on the GEM object, but before that
drm_gem_mmap_obj() already takes a reference, which will be leaked as only
one reference is dropped when the mapping is closed. Drop the extra
reference when dma_buf_mmap() succeeds.
Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tim Huang [Thu, 30 Mar 2023 02:33:02 +0000 (10:33 +0800)]
drm/amdgpu: allow more APUs to do mode2 reset when go to S4
Skip mode2 reset only for IMU enabled APUs when do S4.
This patch is to fix the regression issue
https://gitlab.freedesktop.org/drm/amd/-/issues/2483
It is generated by commit b589626674de ("drm/amdgpu: skip ASIC reset
for APUs when go to S4").
Fixes: b589626674de ("drm/amdgpu: skip ASIC reset for APUs when go to S4") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2483 Tested-by: Yuan Perry <Perry.Yuan@amd.com> Signed-off-by: Tim Huang <tim.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.1.x
Damien Le Moal [Thu, 30 Mar 2023 00:47:58 +0000 (09:47 +0900)]
zonefs: Do not propagate iomap_dio_rw() ENOTBLK error to user space
The call to invalidate_inode_pages2_range() in __iomap_dio_rw() may
fail, in which case -ENOTBLK is returned and this error code is
propagated back to user space trhough iomap_dio_rw() ->
zonefs_file_dio_write() return chain. This error code is fairly obscure
and may confuse the user. Avoid this and be consistent with the behavior
of zonefs_file_dio_append() for similar invalidate_inode_pages2_range()
errors by returning -EBUSY to user space when iomap_dio_rw() returns
-ENOTBLK.
Suggested-by: Christoph Hellwig <hch@infradead.org> Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Damien Le Moal [Wed, 29 Mar 2023 04:16:01 +0000 (13:16 +0900)]
zonefs: Always invalidate last cached page on append write
When a direct append write is executed, the append offset may correspond
to the last page of a sequential file inode which might have been cached
already by buffered reads, page faults with mmap-read or non-direct
readahead. To ensure that the on-disk and cached data is consistant for
such last cached page, make sure to always invalidate it in
zonefs_file_dio_append(). If the invalidation fails, return -EBUSY to
userspace to differentiate from IO errors.
This invalidation will always be a no-op when the FS block size (device
zone write granularity) is equal to the page size (e.g. 4K).
Reported-by: Hans Holmberg <Hans.Holmberg@wdc.com> Fixes: 02ef12a663c7 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Felix Fietkau [Sun, 26 Mar 2023 15:17:09 +0000 (17:17 +0200)]
wifi: mac80211: fix receiving mesh packets in forwarding=0 networks
When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.
Reported-by: Thomas Hühn <thomas.huehn@hs-nordhausen.de> Reported-by: Nick Hainke <vincent@systemli.org> Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces") Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20230326151709.17743-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rx->sta->amsdu_mesh_control is being passed to ieee80211_amsdu_to_8023s
without checking rx->sta. Since it doesn't make sense to accept A-MSDU
packets without a sta, simply add a check earlier.
Fixes: 6e4c0d0460bd ("wifi: mac80211: add a workaround for receiving non-standard mesh A-MSDU") Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20230330090001.60750-2-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paolo Abeni [Thu, 30 Mar 2023 08:47:51 +0000 (10:47 +0200)]
Merge branch 'fix-header-length-on-skb-merging'
Arseniy Krasnov says:
====================
fix header length on skb merging
this patchset fixes appending newly arrived skbuff to the last skbuff of
the socket's queue during rx path. Problem fires when we are trying to
append data to skbuff which was already processed in dequeue callback
at least once. Dequeue callback calls function 'skb_pull()' which changes
'skb->len'. In current implementation 'skb->len' is used to update length
in header of last skbuff after new data was copied to it. This is bug,
because value in header is used to calculate 'rx_bytes'/'fwd_cnt' and
thus must be constant during skbuff lifetime. Here is example, we have
two skbuffs: skb0 with length 10 and skb1 with length 4.
1) skb0 arrives, hdr->len == skb->len == 10, rx_bytes == 10
2) Read 3 bytes from skb0, skb->len == 7, hdr->len == 10, rx_bytes == 10
3) skb1 arrives, hdr->len == skb->len == 4, rx_bytes == 14
4) Append skb1 to skb0, skb0 now has skb->len == 11, hdr->len == 11.
But value of 11 in header is invalid.
5) Read whole skb0, update rx_bytes by 11 from skb0's header.
6) At this moment rx_bytes == 3, but socket's queue is empty.
This bug starts to fire since:
commit 077706165717 ("virtio/vsock: don't use skbuff state to account credit")
In fact, it presents before, but didn't triggered due to a little bit
buggy implementation of credit calculation logic. So i'll use Fixes tag
for it.
I really forgot about this branch in rx path when implemented patch 077706165717.
This patchset contains 3 patches:
1) Fix itself.
2) Patch with WARN_ONCE() to catch such problems in future.
3) Patch with test which triggers skb appending logic. It looks like
simple test with several 'send()' and 'recv()', but it checks, that
skbuff appending works ok.
====================
Arseniy Krasnov [Tue, 28 Mar 2023 11:33:07 +0000 (14:33 +0300)]
test/vsock: new skbuff appending test
This adds test which checks case when data of newly received skbuff is
appended to the last skbuff in the socket's queue. It looks like simple
test with 'send()' and 'recv()', but internally it triggers logic which
appends one received skbuff to another. Test checks that this feature
works correctly.
Arseniy Krasnov [Tue, 28 Mar 2023 11:32:12 +0000 (14:32 +0300)]
virtio/vsock: WARN_ONCE() for invalid state of socket
This adds WARN_ONCE() and return from stream dequeue callback when
socket's queue is empty, but 'rx_bytes' still non-zero. This allows
the detection of potential bugs due to packet merging (see previous
patch).
Arseniy Krasnov [Tue, 28 Mar 2023 11:31:28 +0000 (14:31 +0300)]
virtio/vsock: fix header length on skb merging
This fixes appending newly arrived skbuff to the last skbuff of the
socket's queue. Problem fires when we are trying to append data to skbuff
which was already processed in dequeue callback at least once. Dequeue
callback calls function 'skb_pull()' which changes 'skb->len'. In current
implementation 'skb->len' is used to update length in header of the last
skbuff after new data was copied to it. This is bug, because value in
header is used to calculate 'rx_bytes'/'fwd_cnt' and thus must be not
be changed during skbuff's lifetime.
Bug starts to fire since:
commit 077706165717
("virtio/vsock: don't use skbuff state to account credit")
It presents before, but didn't triggered due to a little bit buggy
implementation of credit calculation logic. So use Fixes tag for it.
Fixes: 077706165717 ("virtio/vsock: don't use skbuff state to account credit") Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 30 Mar 2023 04:48:18 +0000 (21:48 -0700)]
Merge branch 'bnxt_en-3-bug-fixes'
Michael Chan says:
====================
bnxt_en: 3 Bug fixes
This series contains 3 small bug fixes covering ethtool self test, PCI
ID string typos, and some missing 200G link speed ethtool reporting logic.
====================
Michael Chan [Wed, 29 Mar 2023 01:30:21 +0000 (18:30 -0700)]
bnxt_en: Add missing 200G link speed reporting
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 30 Mar 2023 04:46:18 +0000 (21:46 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-28 (ice)
This series contains updates to ice driver only.
Jesse fixes mismatched header documentation reported when building with
W=1.
Brett restricts setting of VSI context to only applicable fields for the
given ICE_AQ_VSI_PROP_Q_OPT_VALID bit.
Junfeng adds check when adding Flow Director filters that conflict with
existing filter rules.
Jakob Koschel adds interim variable for iterating to prevent possible
misuse after looping.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
ice: add profile conflict check for AVF FDIR
ice: Fix ice_cfg_rdma_fltr() to only update relevant fields
ice: fix W=1 headers mismatch
====================
Jakub Kicinski [Thu, 30 Mar 2023 04:41:12 +0000 (21:41 -0700)]
Merge tag 'ieee802154-for-net-2023-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan
Stefan Schmidt says:
====================
ieee802154 for net 2023-03-29
Two small fixes this time.
Dongliang Mu removed an unnecessary null pointer check.
Harshit Mogalapalli fixed an int comparison unsigned against signed from a
recent other fix in the ca8210 driver.
* tag 'ieee802154-for-net-2023-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
net: ieee802154: remove an unnecessary null pointer check
ca8210: Fix unsigned mac_len comparison with zero in ca8210_skb_tx()
====================
Jakub Kicinski [Wed, 29 Mar 2023 00:00:13 +0000 (17:00 -0700)]
bnx2x: use the right build_skb() helper
build_skb() no longer accepts slab buffers. Since slab use is fairly
uncommon we prefer the drivers to call a separate slab_build_skb()
function appropriately.
bnx2x uses the old semantics where size of 0 meant buffer from slab.
It sets the fp->rx_frag_size to 0 for MTUs which don't fit in a page.
It needs to call slab_build_skb().
This fixes the WARN_ONCE() of incorrect API use seen with bnx2x.
Alex Elder [Tue, 28 Mar 2023 16:27:51 +0000 (11:27 -0500)]
net: ipa: compute DMA pool size properly
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com> Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com> Fixes: 9dd441e4ed57 ("soc: qcom: ipa: GSI transactions") Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fangzhi Zuo [Wed, 1 Mar 2023 02:34:58 +0000 (21:34 -0500)]
drm/amd/display: Take FEC Overhead into Timeslot Calculation
8b/10b encoding needs to add 3% fec overhead into the pbn.
In the Synapcis Cascaded MST hub, the first stage MST branch device
needs the information to determine the timeslot count for the
second stage MST branch device. Missing this overhead will leads to
insufficient timeslot allocation.
Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fangzhi Zuo [Fri, 24 Feb 2023 18:45:21 +0000 (13:45 -0500)]
drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
Traditional synaptics hub has one MST branch device without virtual dpcd.
Synaptics cascaded hub has two chained MST branch devices. DSC decoding
is performed via root MST branch device, instead of the second MST branch
device.
Linus Torvalds [Wed, 29 Mar 2023 17:24:07 +0000 (10:24 -0700)]
Merge tag 'xtensa-20230327' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix KASAN report in show_stack
- drop linux-xtensa mailing list from the MAINTAINERS file
* tag 'xtensa-20230327' of https://github.com/jcmvbkbc/linux-xtensa:
MAINTAINERS: xtensa: drop linux-xtensa@linux-xtensa.org mailing list
xtensa: fix KASAN report for show_stack
David Gow [Wed, 29 Mar 2023 06:55:34 +0000 (14:55 +0800)]
drm: test: Fix 32-bit issue in drm_buddy_test
The drm_buddy_test KUnit tests verify that returned blocks have sizes
which are powers of two using is_power_of_2(). However, is_power_of_2()
operations on a 'long', but the block size is a u64. So on systems where
long is 32-bit, this can sometimes fail even on correctly sized blocks.
This only reproduces randomly, as the parameters passed to the buddy
allocator in this test are random. The seed 0xb2e06022 reproduced it
fine here.
For now, just hardcode an is_power_of_2() implementation using
x & (x - 1).
Signed-off-by: David Gow <davidgow@google.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: MaÃra Canal <mcanal@igalia.com> Reviewed-by: Arunpravin Paneer Selvam <arunpravin.paneerselvam@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230329065532.2122295-2-davidgow@google.com Signed-off-by: Christian König <christian.koenig@amd.com>
David Gow [Wed, 29 Mar 2023 06:55:32 +0000 (14:55 +0800)]
drm: buddy_allocator: Fix buddy allocator init on 32-bit systems
The drm buddy allocator tests were broken on 32-bit systems, as
rounddown_pow_of_two() takes a long, and the buddy allocator handles
64-bit sizes even on 32-bit systems.
This can be reproduced with the drm_buddy_allocator KUnit tests on i386:
./tools/testing/kunit/kunit.py run --arch i386 \
--kunitconfig ./drivers/gpu/drm/tests drm_buddy
(It results in kernel BUG_ON() when too many blocks are created, due to
the block size being too small.)
This was independently uncovered (and fixed) by LuÃs Mendes, whose patch
added a new u64 variant of rounddown_pow_of_two(). This version instead
recalculates the size based on the order.
Hans de Goede [Sun, 26 Mar 2023 20:54:33 +0000 (22:54 +0200)]
drm/nouveau/kms: Fix backlight registration
The nouveau code used to call drm_fb_helper_initial_config() from
nouveau_fbcon_init() before calling drm_dev_register(). This would
probe all connectors so that drm_connector->status could be used during
backlight registration which runs from nouveau_connector_late_register().
After commit 4a16dd9d18a0 ("drm/nouveau/kms: switch to drm fbdev helpers")
the fbdev emulation code, which now is a drm-client, can only run after
drm_dev_register(). So during backlight registration the connectors are
not probed yet and the drm_connector->status == connected check in
nv50_backlight_init() would now always fail.
Replace the drm_connector->status == connected check with
a drm_helper_probe_detect() == connected check to fix nv_backlight
no longer getting registered because of this.
M Chetan Kumar [Tue, 28 Mar 2023 06:28:44 +0000 (11:58 +0530)]
net: wwan: iosm: fixes 7560 modem crash
ModemManger/Apps probing the wwan0xmmrpc0 port for 7560 Modem results in
modem crash.
7560 Modem FW uses the MBIM interface for control command communication
whereas 7360 uses Intel RPC interface so disable wwan0xmmrpc0 port for
7560.
Fixes: d08b0f8f46e4 ("net: wwan: iosm: add rpc interface for xmm modems") Reported-and-tested-by: Martin <mwolf@adiumentum.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=217200 Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: Shane Parslow <shaneparslow808@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tasos Sahanidis [Wed, 29 Mar 2023 03:24:22 +0000 (06:24 +0300)]
ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
snd_card_ymfpci_remove() was removed in commit c6e6bb5eab74 ("ALSA:
ymfpci: Allocate resources with device-managed APIs"), but the call to
snd_card_new() was not replaced with snd_devm_card_new().
Since there was no longer a call to snd_card_free, unloading the module
would eventually result in Oops:
Felix Fietkau [Fri, 24 Mar 2023 14:04:04 +0000 (15:04 +0100)]
net: ethernet: mtk_eth_soc: fix tx throughput regression with direct 1G links
Using the QDMA tx scheduler to throttle tx to line speed works fine for
switch ports, but apparently caused a regression on non-switch ports.
Based on a number of tests, it seems that this throttling can be safely
dropped without re-introducing the issues on switch ports that the
tx scheduling changes resolved.
Linus Torvalds [Tue, 28 Mar 2023 20:28:52 +0000 (13:28 -0700)]
Merge tag 'urgent-rcu.2023.03.28a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull RCU fix from Paul McKenney:
"This brings the rcu_torture_read event trace into line with the new
trace tools by replacing this event trace's __field() with the
corresponding __array().
Without this, the new trace tools will fail when presented wtih an
rcu_torture_read event trace, which is a regression from the viewpoint
of trace tools users"
Linus Torvalds [Tue, 28 Mar 2023 20:14:47 +0000 (13:14 -0700)]
Merge tag 'linux-kselftest-fixes-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"One single fix for sigaltstack test -Wuninitialized warning found when
building with clang"
* tag 'linux-kselftest-fixes-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: sigaltstack: fix -Wuninitialized
Jakob Koschel [Mon, 20 Mar 2023 12:48:15 +0000 (13:48 +0100)]
ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
The code implicitly assumes that the list iterator finds a correct
handle. If 'vsi_handle' is not found the 'old_agg_vsi_info' was
pointing to an bogus memory location. For safety a separate list
iterator variable should be used to make the != NULL check on
'old_agg_vsi_info' correct under any circumstances.
Additionally Linus proposed to avoid any use of the list iterator
variable after the loop, in the attempt to move the list iterator
variable declaration into the macro to avoid any potential misuse after
the loop. Using it in a pointer comparison after the loop is undefined
behavior and should be omitted if possible [1].
Junfeng Guo [Tue, 14 Mar 2023 02:03:15 +0000 (10:03 +0800)]
ice: add profile conflict check for AVF FDIR
Add profile conflict check while adding some FDIR rules to avoid
unexpected flow behavior, rules may have conflict including:
IPv4 <---> {IPv4_UDP, IPv4_TCP, IPv4_SCTP}
IPv6 <---> {IPv6_UDP, IPv6_TCP, IPv6_SCTP}
For example, when we create an FDIR rule for IPv4, this rule will work
on packets including IPv4, IPv4_UDP, IPv4_TCP and IPv4_SCTP. But if we
then create an FDIR rule for IPv4_UDP and then destroy it, the first
FDIR rule for IPv4 cannot work on pkt IPv4_UDP then.
To prevent this unexpected behavior, we add restriction in software
when creating FDIR rules by adding necessary profile conflict check.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF") Signed-off-by: Junfeng Guo <junfeng.guo@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Mon, 13 Mar 2023 20:36:08 +0000 (13:36 -0700)]
ice: Fix ice_cfg_rdma_fltr() to only update relevant fields
The current implementation causes ice_vsi_update() to update all VSI
fields based on the cached VSI context. This also assumes that the
ICE_AQ_VSI_PROP_Q_OPT_VALID bit is set. This can cause problems if the
VSI context is not correctly synced by the driver. Fix this by only
updating the fields that correspond to ICE_AQ_VSI_PROP_Q_OPT_VALID.
Also, make sure to save the updated result in the cached VSI context
on success.
Fixes: 348048e724a0 ("ice: Implement iidc operations") Co-developed-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jesse Brandeburg [Mon, 13 Mar 2023 20:36:07 +0000 (13:36 -0700)]
ice: fix W=1 headers mismatch
make modules W=1 returns:
.../ice/ice_txrx_lib.c:448: warning: Function parameter or member 'first_idx' not described in 'ice_finalize_xdp_rx'
.../ice/ice_txrx.c:948: warning: Function parameter or member 'ntc' not described in 'ice_get_rx_buf'
.../ice/ice_txrx.c:1038: warning: Excess function parameter 'rx_buf' description in 'ice_construct_skb'
Fix these warnings by adding and deleting the deviant arguments.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Fixes: d7956d81f150 ("ice: Pull out next_to_clean bump out of ice_put_rx_buf()") CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Juergen Gross [Mon, 27 Mar 2023 08:36:46 +0000 (10:36 +0200)]
xen/netback: remove not needed test in xenvif_tx_build_gops()
The tests for the number of grant mapping or copy operations reaching
the array size of the operations buffer at the end of the main loop in
xenvif_tx_build_gops() isn't needed.
The loop can handle at maximum MAX_PENDING_REQS transfer requests, as
XEN_RING_NR_UNCONSUMED_REQUESTS() is taking unsent responses into
consideration, too.
Remove the tests.
Suggested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Juergen Gross [Mon, 27 Mar 2023 08:36:45 +0000 (10:36 +0200)]
xen/netback: don't do grant copy across page boundary
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Wolfram Sang [Mon, 27 Mar 2023 08:31:38 +0000 (10:31 +0200)]
smsc911x: avoid PHY being resumed when interface is not up
SMSC911x doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 3ce9f2bef755 ("net: smsc911x: Stop and start PHY during suspend and resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230327083138.6044-1-wsa+renesas@sang-engineering.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sven Auhagen [Sat, 25 Mar 2023 16:41:05 +0000 (17:41 +0100)]
net: mvpp2: parser fix PPPoE
In PPPoE add all IPv4 header option length to the parser
and adjust the L3 and L4 offset accordingly.
Currently the L4 match does not work with PPPoE and
all packets are matched as L3 IP4 OPT.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sven Auhagen [Sat, 25 Mar 2023 16:40:53 +0000 (17:40 +0100)]
net: mvpp2: parser fix QinQ
The mvpp2 parser entry for QinQ has the inner and outer VLAN
in the wrong order.
Fix the problem by swapping them.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Reviewed-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Lukas Bulwahn [Fri, 24 Mar 2023 08:16:13 +0000 (09:16 +0100)]
MAINTAINERS: remove the linux-nfc@lists.01.org list
Some MAINTAINERS sections mention to mail patches to the list
linux-nfc@lists.01.org. Probably due to changes on Intel's 01.org website
and servers, the list server lists.01.org/ml01.01.org is simply gone.
Considering emails recorded on lore.kernel.org, only a handful of emails
where sent to the linux-nfc@lists.01.org list, and they are usually also
sent to the netdev mailing list as well, where they are then picked up.
So, there is no big benefit in restoring the linux-nfc elsewhere.
Remove all occurrences of the linux-nfc@lists.01.org list in MAINTAINERS.
Linus Torvalds [Mon, 27 Mar 2023 19:22:45 +0000 (12:22 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"RISC-V:
- Fix VM hang in case of timer delta being zero
ARM:
- MMU fixes:
- Read the MMU notifier seq before dropping the mmap lock to guard
against reading a potentially stale VMA
- Disable interrupts when walking user page tables to protect
against the page table being freed
- Read the MTE permissions for the VMA within the mmap lock
critical section, avoiding the use of a potentally stale VMA
pointer
- vPMU fixes:
- Return the sum of the current perf event value and PMC snapshot
for reads from userspace
- Don't save the value of guest writes to PMCR_EL0.{C,P}, which
could otherwise lead to userspace erroneously resetting the vPMU
during VM save/restore"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
riscv/kvm: Fix VM hang in case of timer delta being zero.
KVM: arm64: Check for kvm_vma_mte_allowed in the critical section
KVM: arm64: Disable interrupts while walking userspace PTs
KVM: arm64: Retry fault if vma_lookup() results become invalid
KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU
KVM: arm64: PMU: Fix GET_ONE_REG for vPMC regs to return the current value
Linus Torvalds [Mon, 27 Mar 2023 16:45:39 +0000 (09:45 -0700)]
Merge tag 'platform-drivers-x86-v6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Intel tpmi/vsec fixes
- think-lmi fixes
- two other small fixes / hw-id additions
* tag 'platform-drivers-x86-v6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/surface: aggregator: Add missing fwnode_handle_put()
platform/x86: think-lmi: Add possible_values for ThinkStation
platform/x86: think-lmi: only display possible_values if available
platform/x86: think-lmi: use correct possible_values delimiters
platform/x86: think-lmi: add missing type attribute
platform/x86 (gigabyte-wmi): Add support for A320M-S2H V2
platform/x86/intel: tpmi: Revise the comment of intel_vsec_add_aux
platform/x86/intel: tpmi: Fix double free in tpmi_create_device()
platform/x86/intel: vsec: Fix a memory leak in intel_vsec_add_aux
- mxic-ecc: Fix mxic_ecc_data_xfer_wait_for_completion() when irq is
used
Binging fixes:
- jedec,spi-nor: Document CPOL/CPHA support"
* tag 'mtd/fixes-for-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: meson: invalidate cache on polling ECC bit
mtd: rawnand: nandsim: Artificially prevent sequential page reads
dt-bindings: mtd: jedec,spi-nor: Document CPOL/CPHA support
mtd: nand: mxic-ecc: Fix mxic_ecc_data_xfer_wait_for_completion() when irq is used
mtd: rawnand: meson: initialize struct with zeroes
Tony Krowiak [Mon, 20 Mar 2023 15:04:47 +0000 (11:04 -0400)]
s390/vfio-ap: fix memory leak in vfio_ap device driver
The device release callback function invoked to release the matrix device
uses the dev_get_drvdata(device *dev) function to retrieve the
pointer to the vfio_matrix_dev object in order to free its storage. The
problem is, this object is not stored as drvdata with the device; since the
kfree function will accept a NULL pointer, the memory for the
vfio_matrix_dev object is never freed.
Since the device being released is contained within the vfio_matrix_dev
object, the container_of macro will be used to retrieve its pointer.
Fixes: 1fde573413b5 ("s390: vfio-ap: base implementation of VFIO AP device driver") Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Link: https://lore.kernel.org/r/20230320150447.34557-1-akrowiak@linux.ibm.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Heiko Carstens [Thu, 23 Mar 2023 12:09:16 +0000 (13:09 +0100)]
s390/uaccess: add missing earlyclobber annotations to __clear_user()
Add missing earlyclobber annotation to size, to, and tmp2 operands of the
__clear_user() inline assembly since they are modified or written to before
the last usage of all input operands. This can lead to incorrect register
allocation for the inline assembly.
Fixes: 6c2a9e6df604 ("[S390] Use alternative user-copy operations for new hardware.") Reported-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/all/20230321122514.1743889-3-mark.rutland@arm.com/ Cc: stable@vger.kernel.org Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
projects / users / jedix / linux-maple.git / log