Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Fixes: c7e2b9689 ("sched: introduce vlan action") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.
However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.
In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.
Fixes: 5eb5f8608ef1 ("net: qualcomm: rmnet: Add support for TX checksum offload") Cc: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: René van Dorst <opensource@vdorst.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 217962615662 ("net: phy: warn if phy_start is called from invalid state") Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f7034 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()") Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.
Without this fix during destroy of LAG interface, we observed following
errors:
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xe4ac33)
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xa5aee8).
Fixes: a31208b1e11d ("net/mlx5_core: New init and exit flow for mlx5_core") Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Mark Zhang <markz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,
if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)
or after bailed out the loop,
for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)
As the result, there could be some "frag" have uninitialized
value of "last_in_page".
Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().
UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
dump_backtrace+0x0/0x264
show_stack+0x20/0x2c
dump_stack+0xb0/0x104
__ubsan_handle_load_invalid_value+0x104/0x128
mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
net_rx_action+0x248/0x940
__do_softirq+0x350/0x7b8
irq_exit+0x200/0x26c
__handle_domain_irq+0xc8/0x128
gic_handle_irq+0x138/0x228
el1_irq+0xb8/0x140
arch_cpu_idle+0x1a4/0x348
do_idle+0x114/0x1b0
cpu_startup_entry+0x24/0x28
rest_init+0x1ac/0x1dc
arch_call_rest_init+0x10/0x18
start_kernel+0x4d4/0x57c
Fixes: 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit aca51397d014 ("netns: Fix arbitrary net_device-s corruptions
on net_ns stop.") introduced a possibility to hit a BUG in case device
is returning back to init_net and two following conditions are met:
1) dev->ifindex value is used in a name of another "dev%d"
device in init_net.
2) dev->name is used by another device in init_net.
Under real life circumstances this is hard to get. Therefore this has
been present happily for over 10 years. To reproduce:
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
3: enp0s2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip netns add ns1
$ ip -n ns1 link add dummy1ns1 type dummy
$ ip -n ns1 link add dummy2ns1 type dummy
$ ip link set enp0s2 netns ns1
$ ip -n ns1 link set enp0s2 name dummy0
[ 100.858894] virtio_net virtio0 dummy0: renamed from enp0s2
$ ip link add dev4 type dummy
$ ip -n ns1 a
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: dummy1ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 16:63:4c:38:3e:ff brd ff:ff:ff:ff:ff:ff
3: dummy2ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether aa:9e:86:dd:6b:5d brd ff:ff:ff:ff:ff:ff
4: dummy0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
4: dev4: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 5a:e1:4a:b6:ec:f8 brd ff:ff:ff:ff:ff:ff
$ ip netns del ns1
[ 158.717795] default_device_exit: failed to move dummy0 to init_net: -17
[ 158.719316] ------------[ cut here ]------------
[ 158.720591] kernel BUG at net/core/dev.c:9824!
[ 158.722260] invalid opcode: 0000 [#1] SMP KASAN PTI
[ 158.723728] CPU: 0 PID: 56 Comm: kworker/u2:1 Not tainted 5.3.0-rc1+ #18
[ 158.725422] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
[ 158.727508] Workqueue: netns cleanup_net
[ 158.728915] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[ 158.730683] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[ 158.736854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[ 158.738752] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[ 158.741369] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[ 158.743418] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[ 158.745626] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[ 158.748405] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[ 158.750638] FS: 0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[ 158.752944] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 158.755245] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[ 158.757654] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 158.760012] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 158.762758] Call Trace:
[ 158.763882] ? dev_change_net_namespace+0xbb0/0xbb0
[ 158.766148] ? devlink_nl_cmd_set_doit+0x520/0x520
[ 158.768034] ? dev_change_net_namespace+0xbb0/0xbb0
[ 158.769870] ops_exit_list.isra.0+0xa8/0x150
[ 158.771544] cleanup_net+0x446/0x8f0
[ 158.772945] ? unregister_pernet_operations+0x4a0/0x4a0
[ 158.775294] process_one_work+0xa1a/0x1740
[ 158.776896] ? pwq_dec_nr_in_flight+0x310/0x310
[ 158.779143] ? do_raw_spin_lock+0x11b/0x280
[ 158.780848] worker_thread+0x9e/0x1060
[ 158.782500] ? process_one_work+0x1740/0x1740
[ 158.784454] kthread+0x31b/0x420
[ 158.786082] ? __kthread_create_on_node+0x3f0/0x3f0
[ 158.788286] ret_from_fork+0x3a/0x50
[ 158.789871] ---[ end trace defd6c657c71f936 ]---
[ 158.792273] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[ 158.795478] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[ 158.804854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[ 158.807865] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[ 158.811794] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[ 158.816652] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[ 158.820930] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[ 158.825113] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[ 158.829899] FS: 0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[ 158.834923] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 158.838164] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[ 158.841917] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 158.845149] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fix this by checking if a device with the same name exists in init_net
and fallback to original code - dev%d to allocate name - in case it does.
This was found using syzkaller.
Fixes: aca51397d014 ("netns: Fix arbitrary net_device-s corruptions on net_ns stop.") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
Reported-by: michael-dev <michael-dev@fami-braun.de> Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a87 ("bridge: add flags to distinguish permanent mdb entires") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()
This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.
Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MTU change code can call napi_disable() with the device already down,
leading to a deadlock. Also, lot of code is duplicated unnecessarily.
Rework mvpp2_change_mtu() to avoid the deadlock and remove duplicated code.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mvpp2 uses a delayed workqueue to gather traffic statistics.
On module removal the workqueue can be destroyed before calling
cancel_delayed_work_sync() on its works.
Fix it by moving the destroy_workqueue() call after mvpp2_port_remove().
Also remove an unneeded call to flush_workqueue()
We need the same checks introduced by commit cb9f1b783850
("ip: validate header length on virtual device xmit") for
ipip tunnel.
Fixes: cb9f1b783850b ("ip: validate header length on virtual device xmit") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip4ip6/ip6ip6 tunnels run iptunnel_handle_offloads on xmit which
can cause a possible use-after-free accessing iph/ipv6h pointer
since the packet will be 'uncloned' running pskb_expand_head if
it is a cloned gso skb.
Fixes: 0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull()
which may change skb->data, so we need to re-load ipv6h at
the right place.
Fixes: 898b29798e36 ("ip6_gre: Refactor ip6gre xmit codes") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Orion5.x systems are still using machine files and not device-tree.
Commit 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be
specified for orion-mdio") has replaced devm_clk_get() with of_clk_get(),
leading to a oops at boot and not working network, as reported in
https://lists.debian.org/debian-arm/2019/07/msg00088.html and possibly in
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908712.
Link: https://lists.debian.org/debian-arm/2019/07/msg00088.html Fixes: 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio") Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3968d38917eb ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.
Fixes: 3968d38917eb ("bnx2x: Fix Multi-Cos.") Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
board is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/iphase.c:2765 ia_ioctl() warn: potential spectre issue 'ia_dev' [r] (local cap)
drivers/atm/iphase.c:2774 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2782 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2816 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2823 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2830 ia_ioctl() warn: potential spectre issue '_ia_dev' [r] (local cap)
drivers/atm/iphase.c:2845 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2856 ia_ioctl() warn: possible spectre second half. 'iadev'
Fix this by sanitizing board before using it to index ia_dev and _ia_dev
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this one as well.
Jonathan Teh (@jonathan-teh) reported and tested the quirk.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/15
The recent USB core code performs sanity checks for the given pipe and
EP types, and it can be hit by manipulated USB descriptors by syzbot.
For making syzbot happier, this patch introduces a local helper for a
sanity check in the driver side and calls it at each place before the
message handling, so that we can avoid the WARNING splats.
A multithreaded namespace creation/destruction stress test currently
deadlocks with the following lockup signature:
INFO: task ndctl:2924 blocked for more than 122 seconds.
Tainted: G OE 5.2.0-rc4+ #3382
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ndctl D 0 2924 1176 0x00000000
Call Trace:
? __schedule+0x27e/0x780
schedule+0x30/0xb0
wait_nvdimm_bus_probe_idle+0x8a/0xd0 [libnvdimm]
? finish_wait+0x80/0x80
uuid_store+0xe6/0x2e0 [libnvdimm]
kernfs_fop_write+0xf0/0x1a0
vfs_write+0xb7/0x1b0
ksys_write+0x5c/0xd0
do_syscall_64+0x60/0x240
INFO: task ndctl:2923 blocked for more than 122 seconds.
Tainted: G OE 5.2.0-rc4+ #3382
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ndctl D 0 2923 1175 0x00000000
Call Trace:
? __schedule+0x27e/0x780
? __mutex_lock+0x489/0x910
schedule+0x30/0xb0
schedule_preempt_disabled+0x11/0x20
__mutex_lock+0x48e/0x910
? nvdimm_namespace_common_probe+0x95/0x4d0 [libnvdimm]
? __lock_acquire+0x23f/0x1710
? nvdimm_namespace_common_probe+0x95/0x4d0 [libnvdimm]
nvdimm_namespace_common_probe+0x95/0x4d0 [libnvdimm]
__dax_pmem_probe+0x5e/0x210 [dax_pmem_core]
? nvdimm_bus_probe+0x1d0/0x2c0 [libnvdimm]
dax_pmem_probe+0xc/0x20 [dax_pmem]
nvdimm_bus_probe+0x90/0x2c0 [libnvdimm]
really_probe+0xef/0x390
driver_probe_device+0xb4/0x100
In this sequence an 'nd_dax' device is being probed and trying to take
the lock on its backing namespace to validate that the 'nd_dax' device
indeed has exclusive access to the backing namespace. Meanwhile, another
thread is trying to update the uuid property of that same backing
namespace. So one thread is in the probe path trying to acquire the
lock, and the other thread has acquired the lock and tries to flush the
probe path.
Fix this deadlock by not holding the namespace device_lock over the
wait_nvdimm_bus_probe_idle() synchronization step. In turn this requires
the device_lock to be held on entry to wait_nvdimm_bus_probe_idle() and
subsequently dropped internally to wait_nvdimm_bus_probe_idle().
In preparation for not holding a lock over the execution of nd_ioctl(),
update the implementation to allow multiple threads to be attempting
ioctls at the same time. The bus lock still prevents multiple in-flight
->ndctl() invocations from corrupting each other's state, but static
global staging buffers are moved to the heap.
Gcc-9 complains for a memset across pointer boundaries, which happens as
the code tries to allocate a flexible array on the stack. Turns out we
cannot do this without relying on gcc-isms, so with this patch we'll embed
the fc_rport_priv structure into fcoe_rport, can use the normal
'container_of' outcast, and will only have to do a memset over one
structure.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On all current Atom processors, instructions that use a segment register
value (e.g. a load or store) will not speculatively execute before the
last writer of that segment retires. Thus they will not use a
speculatively written segment value.
That means on ATOMs there is no speculation through SWAPGS, so the SWAPGS
entry paths can be excluded from the extra LFENCE if PTI is disabled.
Create a separate bug flag for the through SWAPGS speculation and mark all
out-of-order ATOMs and AMD/HYGON CPUs as not affected. The in-order ATOMs
are excluded from the whole mitigation mess anyway.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somehow the swapgs mitigation entry code patch ended up with a JMPQ
instruction instead of JMP, where only the short jump is needed. Some
assembler versions apparently fail to optimize JMPQ into a two-byte JMP
when possible, instead always using a 7-byte JMP with relocation. For
some reason that makes the entry code explode with a #GP during boot.
The previous commit added macro calls in the entry code which mitigate the
Spectre v1 swapgs issue if the X86_FEATURE_FENCE_SWAPGS_* features are
enabled. Enable those features where applicable.
The mitigations may be disabled with "nospectre_v1" or "mitigations=off".
There are different features which can affect the risk of attack:
- When FSGSBASE is enabled, unprivileged users are able to place any
value in GS, using the wrgsbase instruction. This means they can
write a GS value which points to any value in kernel space, which can
be useful with the following gadget in an interrupt/exception/NMI
handler:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
// dependent load or store based on the value of %reg
// for example: mov %(reg1), %reg2
If an interrupt is coming from user space, and the entry code
speculatively skips the swapgs (due to user branch mistraining), it
may speculatively execute the GS-based load and a subsequent dependent
load or store, exposing the kernel data to an L1 side channel leak.
Note that, on Intel, a similar attack exists in the above gadget when
coming from kernel space, if the swapgs gets speculatively executed to
switch back to the user GS. On AMD, this variant isn't possible
because swapgs is serializing with respect to future GS-based
accesses.
NOTE: The FSGSBASE patch set hasn't been merged yet, so the above case
doesn't exist quite yet.
- When FSGSBASE is disabled, the issue is mitigated somewhat because
unprivileged users must use prctl(ARCH_SET_GS) to set GS, which
restricts GS values to user space addresses only. That means the
gadget would need an additional step, since the target kernel address
needs to be read from user space first. Something like:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
mov (%reg1), %reg2
// dependent load or store based on the value of %reg2
// for example: mov %(reg2), %reg3
It's difficult to audit for this gadget in all the handlers, so while
there are no known instances of it, it's entirely possible that it
exists somewhere (or could be introduced in the future). Without
tooling to analyze all such code paths, consider it vulnerable.
Effects of SMAP on the !FSGSBASE case:
- If SMAP is enabled, and the CPU reports RDCL_NO (i.e., not
susceptible to Meltdown), the kernel is prevented from speculatively
reading user space memory, even L1 cached values. This effectively
disables the !FSGSBASE attack vector.
- If SMAP is enabled, but the CPU *is* susceptible to Meltdown, SMAP
still prevents the kernel from speculatively reading user space
memory. But it does *not* prevent the kernel from reading the
user value from L1, if it has already been cached. This is probably
only a small hurdle for an attacker to overcome.
Thanks to Dave Hansen for contributing the speculative_smap() function.
Thanks to Andrew Cooper for providing the inside scoop on whether swapgs
is serializing on AMD.
[ tglx: Fixed the USER fence decision and polished the comment as suggested
by Dave Hansen ]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spectre v1 isn't only about array bounds checks. It can affect any
conditional checks. The kernel entry code interrupt, exception, and NMI
handlers all have conditional swapgs checks. Those may be problematic in
the context of Spectre v1, as kernel code can speculatively run with a user
GS.
For example:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg
mov (%reg), %reg1
When coming from user space, the CPU can speculatively skip the swapgs, and
then do a speculative percpu load using the user GS value. So the user can
speculatively force a read of any kernel value. If a gadget exists which
uses the percpu value as an address in another load/store, then the
contents of the kernel value may become visible via an L1 side channel
attack.
A similar attack exists when coming from kernel space. The CPU can
speculatively do the swapgs, causing the user GS to get used for the rest
of the speculative window.
The mitigation is similar to a traditional Spectre v1 mitigation, except:
a) index masking isn't possible; because the index (percpu offset)
isn't user-controlled; and
b) an lfence is needed in both the "from user" swapgs path and the
"from kernel" non-swapgs path (because of the two attacks described
above).
The user entry swapgs paths already have SWITCH_TO_KERNEL_CR3, which has a
CR3 write when PTI is enabled. Since CR3 writes are serializing, the
lfences can be skipped in those cases.
On the other hand, the kernel entry swapgs paths don't depend on PTI.
To avoid unnecessary lfences for the user entry case, create two separate
features for alternative patching:
It's a waste for the four X86_FEATURE_CQM_* feature bits to occupy two
whole feature bits words. To better utilize feature words, re-define
word 11 to host scattered features and move the four X86_FEATURE_CQM_*
features into Linux defined word 11. More scattered features can be
added in word 11 in the future.
Rename leaf 11 in cpuid_leafs to CPUID_LNX_4 to reflect it's a
Linux-defined leaf.
Rename leaf 12 as CPUID_DUMMY which will be replaced by a meaningful
name in the next patch when CPUID.7.1:EAX occupies world 12.
Maximum number of RMID and cache occupancy scale are retrieved from
CPUID.0xf.1 after scattered CQM features are enumerated. Carve out the
code into a separate function.
KVM doesn't support resctrl now. So it's safe to move the
X86_FEATURE_CQM_* features to scattered features word 11 for KVM.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Aaron Lewis <aaronlewis@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Babu Moger <babu.moger@amd.com> Cc: "Chang S. Bae" <chang.seok.bae@intel.com> Cc: "Sean J Christopherson" <sean.j.christopherson@intel.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Juergen Gross <jgross@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: kvm ML <kvm@vger.kernel.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Nadav Amit <namit@vmware.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Peter Feiner <pfeiner@google.com> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Ravi V Shankar <ravi.v.shankar@intel.com> Cc: Sherry Hurwitz <sherry.hurwitz@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Lendacky <Thomas.Lendacky@amd.com> Cc: x86 <x86@kernel.org> Link: https://lkml.kernel.org/r/1560794416-217638-2-git-send-email-fenghua.yu@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... into a separate function for better readability. Split out from a
patch from Fenghua Yu <fenghua.yu@intel.com> to keep the mechanical,
sole code movement separate for easy review.
GPU hang observed during the guest OCL conformance test which is caused
by THP GTT feature used durning the test.
It was observed the same GFN with different size (4K and 2M) requested
from the guest in GVT. So during the guest page dma map stage, it is
required to unmap first with orginal size and then remap again with
requested size.
We got the wrong offsets (could they have changed?). New values were
computed off an error state by looking up the register offset in the
context image as written by the HW.
The field flow->resync_npkts is added for TID RDMA WRITE request and
zero-ed when a TID RDMA WRITE RESP packet is received by the requester.
This field is used to rewind a request during retry in the function
hfi1_tid_rdma_restart_req() shared by both TID RDMA WRITE and TID RDMA
READ requests. Therefore, when a TID RDMA READ request is retried, this
field may not be initialized at all, which causes the retry to start at an
incorrect psn, leading to the drop of the retry request by the responder.
This patch fixes the problem by zeroing out the field when the flow memory
is allocated.
Fixes: 838b6fd2d9ca ("IB/hfi1: TID RDMA RcvArray programming and TID allocation") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190715164534.74174.6177.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a TID sequence error occurs while receiving TID RDMA READ RESP
packets, all packets after flow->flow_state.r_next_psn should be dropped,
including those response packets for subsequent segments.
The current implementation will drop the subsequent response packets for
the segment to complete next, but may accept packets for subsequent
segments and therefore mistakenly advance the r_next_psn fields for the
corresponding software flows. This may result in failures to complete
subsequent segments after the current segment is completed.
The fix is to only use the flow pointed by req->clear_tail for checking
KDETH PSN instead of finding a flow from the request's flow array.
Fixes: b885d5be9ca1 ("IB/hfi1: Unify the software PSN check for TID RDMA READ/WRITE") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190715164540.74174.54702.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The specification for the Toeplitz function doesn't require to set the key
explicitly to be symmetric. In case a symmetric functionality is required
a symmetric key can be simply used.
Wrongly forcing the algorithm to symmetric causes the wrong packet
distribution and a performance degradation.
Fix unreg_umr to move the MR to a kernel owned PD (i.e. the UMR PD) which
can't be accessed by userspace.
This ensures that nothing can continue to access the MR once it has been
placed in the kernels cache for reuse.
MRs in the cache continue to have their HW state, including DMA tables,
present. Even though the MR has been invalidated, changing the PD provides
an additional layer of protection against use of the MR.
Link: https://lore.kernel.org/r/20190723065733.4899-5-leon@kernel.org Cc: <stable@vger.kernel.org> # 3.10 Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix unreg_umr to ignore the mkey state and do not fail if was freed. This
prevents a case that a user space application already changed the mkey
state to free and then the UMR operation will fail leaving the mkey in an
inappropriate state.
Link: https://lore.kernel.org/r/20190723065733.4899-3-leon@kernel.org Cc: <stable@vger.kernel.org> # 3.19 Fixes: 968e78dd9644 ("IB/mlx5: Enhance UMR support to allow partial page table update") Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Which is due to the read side of the client_data_rwsem being obtained
recursively through a work queue flush during cm client removal.
The lock is being held across the remove in remove_client_context() so
that the function is a fence, once it returns the client is removed. This
is required so that the two callers do not proceed with destruction until
the client completes removal.
Instead of using client_data_rwsem use the existing device unregistration
refcount and add a similar client unregistration (client->uses) refcount.
This will fence the two unregistration paths without holding any locks.
A GID entry consists of GID, vlan, netdev and smac. Extend GID duplicate
check comparisons to consider vlan_id as well to support IPv6 VLAN based
link local addresses. Introduce a new structure (bnxt_qplib_gid_info) to
hold gid and vlan_id information.
The issue is discussed in the following thread
https://lore.kernel.org/r/AM0PR05MB4866CFEDCDF3CDA1D7D18AA5D1F20@AM0PR05MB4866.eurprd05.prod.outlook.com
Fixes: 823b23da7113 ("IB/core: Allow vlan link local address based RoCE GIDs") Cc: <stable@vger.kernel.org> # v5.2+ Link: https://lore.kernel.org/r/20190715091913.15726-1-selvin.xavier@broadcom.com Reported-by: Yi Zhang <yi.zhang@redhat.com> Co-developed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'commit df9bde015a72 ("xen/gntdev.c: convert to use vm_map_pages()")'
breaks gntdev driver. If vma->vm_pgoff > 0, vm_map_pages()
will:
- use map->pages starting at vma->vm_pgoff instead of 0
- verify map->count against vma_pages()+vma->vm_pgoff instead of just
vma_pages().
In practice, this breaks using a single gntdev FD for mapping multiple
grants.
The reason is -> ( copying Marek's word from discussion)
vma->vm_pgoff is used as index passed to gntdev_find_map_index. It's
basically using this parameter for "which grant reference to map".
map struct returned by gntdev_find_map_index() describes just the pages
to be mapped. Specifically map->pages[0] should be mapped at
vma->vm_start, not vma->vm_start+vma->vm_pgoff*PAGE_SIZE.
When trying to map grant with index (aka vma->vm_pgoff) > 1,
__vm_map_pages() will refuse to map it because it will expect map->count
to be at least vma_pages(vma)+vma->vm_pgoff, while it is exactly
vma_pages(vma).
Converting vm_map_pages() to use vm_map_pages_zero() will fix the
problem.
Marek has tested and confirmed the same.
Cc: stable@vger.kernel.org # v5.2+ Fixes: df9bde015a72 ("xen/gntdev.c: convert to use vm_map_pages()") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition in xen_swiotlb_free_coherent() for deciding whether to
call xen_destroy_contiguous_region() is wrong: in case the region to
be freed is not contiguous calling xen_destroy_contiguous_region() is
the wrong thing to do: it would result in inconsistent mappings of
multiple PFNs to the same MFN. This will lead to various strange
crashes or data corruption.
Instead of calling xen_destroy_contiguous_region() in that case a
warning should be issued as that situation should never occur.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abbbdf12497d ("replace kill_bdev() with __invalidate_device()")
once did this, but 29eaadc03649 ("nbd: stop using the bdev everywhere")
resurrected kill_bdev() and it has been there since then. So buffer_head
mappings still get killed on a server disconnection, and we can still
hit the BUG_ON on a filesystem on the top of the nbd device.
Although SAS3 & SAS3.5 IT HBA controllers support 64-bit DMA addressing, as
per hardware design, if DMA-able range contains all 64-bits
set (0xFFFFFFFF-FFFFFFFF) then it results in a firmware fault.
E.g. SGE's start address is 0xFFFFFFFF-FFFF000 and data length is 0x1000
bytes. when HBA tries to DMA the data at 0xFFFFFFFF-FFFFFFFF location then
HBA will fault the firmware.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: <stable@vger.kernel.org> # 5.1.20+ Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ 29.387920] Memory state around the buggy address:
[ 29.388771] ffff888067172080: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ 29.390062] ffff888067172100: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 29.391325] >ffff888067172180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 29.392578] ^
[ 29.393480] ffff888067172200: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
[ 29.394744] ffff888067172280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 29.396003] ==================================================================
[ 29.397260] Disabling lock debugging due to kernel taint
io_sq_wq_submit_work free and read req again.
Cc: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Cc: linux-block@vger.kernel.org Cc: stable@vger.kernel.org Fixes: f7b76ac9d17e ("io_uring: fix counter inc/dec mismatch in async_list") Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CTR_EL0.{CWG,ERG} are 0b0000 then they must be interpreted to have
their architecturally maximum values, which defeats the use of
FTR_HIGHER_SAFE when sanitising CPU ID registers on heterogeneous
machines.
Introduce FTR_HIGHER_OR_ZERO_SAFE so that these fields effectively
saturate at zero.
Fixes: 3c739b571084 ("arm64: Keep track of CPU feature registers") Cc: <stable@vger.kernel.org> # 4.4.x- Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d968d2b801d8 ("ARM: 7497/1: hw_breakpoint: allow single-byte
watchpoints on all addresses") changed the validation requirements for
hardware watchpoints on arch/arm/. Update our compat layer to implement
the same relaxation.
Cc: <stable@vger.kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling of the CPU_PM_ENTER_FAILED transition in the Arm PMU PM
notifier code incorrectly skips restoration of the counters. Fix the
logic so that CPU_PM_ENTER_FAILED follows the same path as CPU_PM_EXIT.
Cc: <stable@vger.kernel.org> Fixes: da4e4f18afe0f372 ("drivers/perf: arm_pmu: implement CPU_PM notifier") Reported-by: Anders Roxell <anders.roxell@linaro.org> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With debug info enabled (CONFIG_DEBUG_INFO=y) the resulting vmlinux may get
that huge that we need to increase the start addresss for the decompression
text section otherwise one will face a linker error.
Reported-by: Sven Schnelle <svens@stackframe.org> Tested-by: Sven Schnelle <svens@stackframe.org> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently we don't have an archclean target in our
arch/parisc/Makefile, so files in there never get cleaned out by make
mrproper. This, in turn means that the sizes.h file in
arch/parisc/boot/compressed never gets removed and worse, when you
transition to an O=build/parisc[64] build model it overrides the
generated file. The upshot being my bzImage was building with a SZ_end
that was too small.
On my laptop most memcg kselftests were being skipped because it claimed
cgroup v2 hierarchy wasn't mounted, but this isn't correct. Instead, it
seems current systemd HEAD mounts it with the name "cgroup2" instead of
"cgroup":
After getting a storage server event that causes the DASD device driver
to update its unit address configuration during a device shutdown there is
the possibility of an endless loop in the device driver.
In the system log there will be ongoing DASD error messages with RC: -19.
The reason is that the loop starting the ruac request only terminates when
the retry counter is decreased to 0. But in the sleep_on function there are
early exit paths that do not decrease the retry counter.
Prevent an endless loop by handling those cases separately.
Remove the unnecessary do..while loop since the sleep_on function takes
care of retries by itself.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org # 2.6.25+ Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33ec3e53e7b1 ("loop: Don't change loop device under exclusive
opener") made LOOP_SET_FD ioctl acquire exclusive block device reference
while it updates loop device binding. However this can make perfectly
valid mount(2) fail with EBUSY due to racing LOOP_SET_FD holding
temporarily the exclusive bdev reference in cases like this:
for i in {a..z}{a..z}; do
dd if=/dev/zero of=$i.image bs=1k count=0 seek=1024
mkfs.ext2 $i.image
mkdir mnt$i
done
echo "Run"
for i in {a..z}{a..z}; do
mount -o loop -t ext2 $i.image mnt$i &
done
Fix the problem by not getting full exclusive bdev reference in
LOOP_SET_FD but instead just mark the bdev as being claimed while we
update the binding information. This just blocks new exclusive openers
instead of failing them with EBUSY thus fixing the problem.
Fixes: 33ec3e53e7b1 ("loop: Don't change loop device under exclusive opener") Cc: stable@vger.kernel.org Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com Fixes: 8763cb45ab967 ("mm/migrate: new memory migration helper for use with device memory") Signed-off-by: Ralph Campbell <rcampbell@nvidia.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
objtool points out several conditions that it does not like, depending
on the combination with other configuration options and compiler
variants:
stack protector:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0xbf: call to __stack_chk_fail() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0xbe: call to __stack_chk_fail() with UACCESS enabled
stackleak plugin:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0x4a: call to stackleak_track_stack() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0x4a: call to stackleak_track_stack() with UACCESS enabled
kasan:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0x25: call to memcpy() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0x25: call to memcpy() with UACCESS enabled
The stackleak and kasan options just need to be disabled for this file
as we do for other files already. For the stack protector, we already
attempt to disable it, but this fails on clang because the check is
mixed with the gcc specific -fno-conserve-stack option. According to
Andrey Ryabinin, that option is not even needed, dropping it here fixes
the stackprotector issue.
"howaboutsynergy" reported via kernel buzilla number 204165 that
compact_zone_order was consuming 100% CPU during a stress test for
prolonged periods of time. Specifically the following command, which
should exit in 10 seconds, was taking an excessive time to finish while
the CPU was pegged at 100%.
Note that compaction is entered in rapid succession while scanning and
isolating nothing. The problem is that when a task that is compacting
receives a fatal signal, it retries indefinitely instead of exiting
while making no progress as a fatal signal is pending.
It's not easy to trigger this condition although enabling zswap helps on
the basis that the timing is altered. A very small window has to be hit
for the problem to occur (signal delivered while compacting and
isolating a PFN for migration that is not aligned to SWAP_CLUSTER_MAX).
This was reproduced locally -- 16G single socket system, 8G swap, 30%
zswap configured, vm-bytes 22000000000 using Colin Kings stress-ng
implementation from github running in a loop until the problem hits).
Tracing recorded the problem occurring almost 200K times in a short
window. With this patch, the problem hit 4 times but the task existed
normally instead of consuming CPU.
This problem has existed for some time but it was made worse by commit cf66f0700c8f ("mm, compaction: do not consider a need to reschedule as
contention"). Before that commit, if the same condition was hit then
locks would be quickly contended and compaction would exit that way.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204165 Link: http://lkml.kernel.org/r/20190718085708.GE24383@techsingularity.net Fixes: cf66f0700c8f ("mm, compaction: do not consider a need to reschedule as contention") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [5.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
buffer_migrate_page_norefs() can race with bh users in the following
way:
CPU1 CPU2
buffer_migrate_page_norefs()
buffer_migrate_lock_buffers()
checks bh refs
spin_unlock(&mapping->private_lock)
__find_get_block()
spin_lock(&mapping->private_lock)
grab bh ref
spin_unlock(&mapping->private_lock)
move page do bh work
This can result in various issues like lost updates to buffers (i.e.
metadata corruption) or use after free issues for the old page.
This patch closes the race by holding mapping->private_lock while the
mapping is being moved to a new page. Ordinarily, a reference can be
taken outside of the private_lock using the per-cpu BH LRU but the
references are checked and the LRU invalidated if necessary. The
private_lock is held once the references are known so the buffer lookup
slow path will spin on the private_lock. Between the page lock and
private_lock, it should be impossible for other references to be
acquired and updates to happen during the migration.
A user had reported data corruption issues on a distribution kernel with
a similar page migration implementation as mainline. The data
corruption could not be reproduced with this patch applied. A small
number of migration-intensive tests were run and no performance problems
were noted.
[mgorman@techsingularity.net: Changelog, removed tracing] Link: http://lkml.kernel.org/r/20190718090238.GF24383@techsingularity.net Fixes: 89cb0888ca14 "mm: migrate: provide buffer_migrate_page_norefs()" Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> [5.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shakeel Butt reported premature oom on kernel with
"cgroup_disable=memory" since mem_cgroup_is_root() returns false even
though memcg is actually NULL. The drop_caches is also broken.
It is because commit aeed1d325d42 ("mm/vmscan.c: generalize
shrink_slab() calls in shrink_node()") removed the !memcg check before
!mem_cgroup_is_root(). And, surprisingly root memcg is allocated even
though memory cgroup is disabled by kernel boot parameter.
Add mem_cgroup_disabled() check to make reclaimer work as expected.
Link: http://lkml.kernel.org/r/1563385526-20805-1-git-send-email-yang.shi@linux.alibaba.com Fixes: aeed1d325d42 ("mm/vmscan.c: generalize shrink_slab() calls in shrink_node()") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reported-by: Shakeel Butt <shakeelb@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Jan Hadrava <had@kam.mff.cuni.cz> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Roman Gushchin <guro@fb.com> Cc: Hugh Dickins <hughd@google.com> Cc: Qian Cai <cai@lca.pw> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: <stable@vger.kernel.org> [4.19+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distribution installation images such as Debian include different sets
of modules which can be downloaded dynamically. Such images may notably
include the hda sound modules but not the i915 DRM module, even if the
latter was enabled at build time, as reported on
https://bugs.debian.org/931507
In such a case hdac_i915 would be linked in and try to load the i915
module, fail since it is not there, but still wait for a whole minute
before giving up binding with it.
This fixes such as case by only waiting for the binding if the module
was properly loaded (or module support is disabled, in which case i915
is already compiled-in anyway).
Since roles_init() adds some entries to the role hash table, we need to
destroy also its keys/values on error, otherwise we get a memory leak in
the error path.
Cc: <stable@vger.kernel.org> Reported-by: syzbot+fee3a14d4cdf92646287@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to commit 4a6d8cf90017 ("powerpc/mm: don't use pte_alloc_kernel()
until slab is available on PPC32"), pte_alloc_kernel() cannot be used
during early KASAN init.
In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels] Fixes: 0ef6f3213dac ("i2c: at91: add support for new alternative command mode") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split] Fixes: fac368a04048 ("i2c: at91: add new driver") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Tested-by: Raag Jadav <raagjadav@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use SMBUS_MASTER_DATA_READ.MASTER_RD_STATUS bit to check for RX
FIFO empty condition because SMBUS_MASTER_FIFO_CONTROL.MASTER_RX_PKT_COUNT
is not updated for read >= 64 bytes. This fixes the issue when trying to
read from the I2C slave more than 63 bytes.
Fixes: c24b8d574b7c ("i2c: iproc: Extend I2C read up to 255 bytes") Cc: stable@kernel.org Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices are not supposed to support on-die ECC but experience
shows that internal ECC machinery can actually be enabled through the
"SET FEATURE (EFh)" command, even if a read of the "READ ID Parameter
Tables" returns that it is not.
Currently, the driver checks the "READ ID Parameter" field directly
after having enabled the feature. If the check fails it returns
immediately but leaves the ECC on. When using buggy chips like
MT29F2G08ABAGA and MT29F2G08ABBGA, all future read/program cycles will
go through the on-die ECC, confusing the host controller which is
supposed to be the one handling correction.
To address this in a common way we need to turn off the on-die ECC
directly after reading the "READ ID Parameter" and before checking the
"ECC status".
Looks like a regression got introduced into nv50_mstc_atomic_check()
that somehow didn't get found until now. If userspace changes
crtc_state->active to false but leaves the CRTC enabled, we end up
calling drm_dp_atomic_find_vcpi_slots() using the PBN calculated in
asyh->dp.pbn. However, if the display is inactive we end up calculating
a PBN of 0, which inadvertently causes us to have an allocation of 0.
>From there, if userspace then disables the CRTC afterwards we end up
accidentally attempting to free the VCPI twice:
So, fix this by doing what we probably should have done from the start: only
call drm_dp_atomic_find_vcpi_slots() when crtc_state->mode_changed is set, so
that VCPI allocations remain for as long as the CRTC is enabled.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST") Cc: Lyude Paul <lyude@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@redhat.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Juston Li <juston.li@intel.com> Cc: Karol Herbst <karolherbst@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Cc: <stable@vger.kernel.org> # v5.1+ Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190801220216.15323-1-lyude@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sl is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
Fix this by sanitizing sl before using it to index ibp->sl_to_sc.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
When a pin is active-low, logical trigger edge should be inverted to match
the same interrupt opportunity.
For example, a button pushed triggers falling edge in ACTIVE_HIGH case; in
ACTIVE_LOW case, the button pushed triggers rising edge. For user space the
IRQ requesting doesn't need to do any modification except to configuring
GPIOHANDLE_REQUEST_ACTIVE_LOW.
For example, we want to catch the event when the button is pushed. The
button on the original board drives level to be low when it is pushed, and
drives level to be high when it is released.
while (1) {
read(fd, &dat, sizeof(dat));
if (dat.id == GPIOEVENT_EVENT_FALLING_EDGE)
printf("button pushed\n");
}
Run the same logic on another board which the polarity of the button is
inverted; it drives level to be high when pushed, and level to be low when
released. For this inversion we add flag GPIOHANDLE_REQUEST_ACTIVE_LOW:
At the result, there are no any events caught when the button is pushed.
By the way, button releasing will emit a "falling" event. The timing of
"falling" catching is not expected.
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
desc->flags may already have values set by of_gpiochip_add() so make
sure that this isn't undone when setting the initial direction.
Cc: stable@vger.kernel.org Fixes: 3edfb7bd76bd1cba ("gpiolib: Show correct direction from the beginning") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20190707203558.10993-1-chris.packham@alliedtelesis.co.nz Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While using the mmc_spi driver occasionally errors like this popped up:
mmcblk0: error -84 transferring data end_request: I/O error, dev mmcblk0, sector 581756
I looked on the Internet for occurrences of the same problem and came
across a helpful post [1]. It includes source code to reproduce the bug.
There is also an analysis about the cause. During transmission data in the
supplied buffer is being modified. Thus the previously calculated checksum
is not correct anymore.
After some digging I found out that device drivers are supposed to report
they need stable writes. To fix this I set the appropriate flag at queue
initialization if CRC checksumming is enabled for that SPI host.
Signed-off-by: Andreas Koop <andreas.koop@zf.com>
[shihpo: Rebase on top of v5.3-rc1] Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> CC: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the SD host controller tries to probe again due to the derferred
probe mechanism, it will always keep the SD host device as runtime
resume state due to missing the runtime put operation in error path
last time.
Thus add the pm_runtime_put_noidle() in error path to make the PM runtime
counter balance, which can make the SD host device's PM runtime work well.
In commit 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after
response errors.") we fixed a tuning-induced hang that I saw when
stress testing tuning on certain SD cards. I won't re-hash that whole
commit, but the summary is that as a normal part of tuning you need to
deal with transfer errors and there were cases where these transfer
errors was putting my system into a bad state causing all future
transfers to fail. That commit fixed handling of the transfer errors
for me.
In downstream Chrome OS my fix landed and had the same behavior for
all SD/MMC commands. However, it looks like when the commit landed
upstream we limited it to only SD tuning commands. Presumably this
was to try to get around problems that Alim Akhtar reported on exynos
[1].
Unfortunately while stress testing reboots (and suspend/resume) on
some rk3288-based Chromebooks I found the same problem on the eMMC on
some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC
tuning command is different (MMC_SEND_TUNING_BLOCK_HS200
vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the
same situation.
I'm hoping that whatever problems exynos was having in the past are
somehow magically fixed now and we can make the behavior the same for
all commands.
Fixes: 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Alim Akhtar <alim.akhtar@gmail.com> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition checking whether put_unlocked_entry() needs to wake up
following waiter got broken by commit 23c84eb78375 ("dax: Fix missed
wakeup with PMD faults"). We need to wake the waiter whenever the passed
entry is valid (i.e., non-NULL and not special conflict entry). This
could lead to processes never being woken up when waiting for entry
lock. Fix the condition.
Cc: <stable@vger.kernel.org> Link: http://lore.kernel.org/r/20190729120228.GC17833@quack2.suse.cz Fixes: 23c84eb78375 ("dax: Fix missed wakeup with PMD faults") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When one transaction is finishing its commit, it is possible for another
transaction to start and enter its initial commit phase as well. If the
first ends up getting aborted, we have a small time window where the second
transaction commit does not notice that the previous transaction aborted
and ends up committing, writing a superblock that points to btrees that
reference extent buffers (nodes and leafs) that were not persisted to disk.
The consequence is that after mounting the filesystem again, we will be
unable to load some btree nodes/leafs, either because the content on disk
is either garbage (or just zeroes) or corresponds to the old content of a
previouly COWed or deleted node/leaf, resulting in the well known error
messages "parent transid verify failed on ...".
The following sequence diagram illustrates how this can happen.
CPU 1 CPU 2
<at transaction N>
btrfs_commit_transaction()
(...)
--> sets transaction state to
TRANS_STATE_UNBLOCKED
--> sets fs_info->running_transaction
to NULL
(...)
btrfs_start_transaction()
start_transaction()
wait_current_trans()
--> returns immediately
because
fs_info->running_transaction
is NULL
join_transaction()
--> creates transaction N + 1
--> sets
fs_info->running_transaction
to transaction N + 1
--> adds transaction N + 1 to
the fs_info->trans_list list
--> returns transaction handle
pointing to the new
transaction N + 1
(...)
btrfs_sync_file()
btrfs_start_transaction()
--> returns handle to
transaction N + 1
(...)
btrfs_write_and_wait_transaction()
--> writeback of some extent
buffer fails, returns an
error
btrfs_handle_fs_error()
--> sets BTRFS_FS_STATE_ERROR in
fs_info->fs_state
--> jumps to label "scrub_continue"
cleanup_transaction()
btrfs_abort_transaction(N)
--> sets BTRFS_FS_STATE_TRANS_ABORTED
flag in fs_info->fs_state
--> sets aborted field in the
transaction and transaction
handle structures, for
transaction N only
--> removes transaction from the
list fs_info->trans_list
btrfs_commit_transaction(N + 1)
--> transaction N + 1 was not
aborted, so it proceeds
(...)
--> sets the transaction's state
to TRANS_STATE_COMMIT_START
--> does not find the previous
transaction (N) in the
fs_info->trans_list, so it
doesn't know that transaction
was aborted, and the commit
of transaction N + 1 proceeds
(...)
--> sets transaction N + 1 state
to TRANS_STATE_UNBLOCKED
btrfs_write_and_wait_transaction()
--> succeeds writing all extent
buffers created in the
transaction N + 1
write_all_supers()
--> succeeds
--> we now have a superblock on
disk that points to trees
that refer to at least one
extent buffer that was
never persisted
So fix this by updating the transaction commit path to check if the flag
BTRFS_FS_STATE_TRANS_ABORTED is set on fs_info->fs_state if after setting
the transaction to the TRANS_STATE_COMMIT_START we do not find any previous
transaction in the fs_info->trans_list. If the flag is set, just fail the
transaction commit with -EROFS, as we do in other places. The exact error
code for the previous transaction abort was already logged and reported.
Fixes: 49b25e0540904b ("btrfs: enhance transaction abort infrastructure") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing an incremental send operation we can fail if we previously did
deduplication operations against a file that exists in both snapshots. In
that case we will fail the send operation with -EIO and print a message
to dmesg/syslog like the following:
BTRFS error (device sdc): Send: inconsistent snapshot, found updated \
extent for inode 257 without updated inode item, send root is 258, \
parent root is 257
This requires that we deduplicate to the same file in both snapshots for
the same amount of times on each snapshot. The issue happens because a
deduplication only updates the iversion of an inode and does not update
any other field of the inode, therefore if we deduplicate the file on
each snapshot for the same amount of time, the inode will have the same
iversion value (stored as the "sequence" field on the inode item) on both
snapshots, therefore it will be seen as unchanged between in the send
snapshot while there are new/updated/deleted extent items when comparing
to the parent snapshot. This makes the send operation return -EIO and
print an error message.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our first file. The first half of the file has several 64Kb
# extents while the second half as a single 512Kb extent.
$ xfs_io -f -s -c "pwrite -S 0xb8 -b 64K 0 512K" /mnt/foo
$ xfs_io -c "pwrite -S 0xb8 512K 512K" /mnt/foo
# Create the base snapshot and the parent send stream from it.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap1
$ btrfs send -f /tmp/1.snap /mnt/mysnap1
# Create our second file, that has exactly the same data as the first
# file.
$ xfs_io -f -c "pwrite -S 0xb8 0 1M" /mnt/bar
# Create the second snapshot, used for the incremental send, before
# doing the file deduplication.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap2
# Now before creating the incremental send stream:
#
# 1) Deduplicate into a subrange of file foo in snapshot mysnap1. This
# will drop several extent items and add a new one, also updating
# the inode's iversion (sequence field in inode item) by 1, but not
# any other field of the inode;
#
# 2) Deduplicate into a different subrange of file foo in snapshot
# mysnap2. This will replace an extent item with a new one, also
# updating the inode's iversion by 1 but not any other field of the
# inode.
#
# After these two deduplication operations, the inode items, for file
# foo, are identical in both snapshots, but we have different extent
# items for this inode in both snapshots. We want to check this doesn't
# cause send to fail with an error or produce an incorrect stream.
This issue started happening back in 2015 when deduplication was updated
to not update the inode's ctime and mtime and update only the iversion.
Back then we would hit a BUG_ON() in send, but later in 2016 send was
updated to return -EIO and print the error message instead of doing the
BUG_ON().
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203933 Fixes: 1c919a5e13702c ("btrfs: don't update mtime/ctime on deduped inodes") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a build rule fails, the .DELETE_ON_ERROR special target removes the
target, but does nothing for the .*.cmd file, which might be corrupted.
So, .*.cmd files should be included only when the corresponding targets
exist.
Commit 392885ee82d3 ("kbuild: let fixdep directly write to .*.cmd
files") missed to fix up this file.
Prior to this commit, starting nconfig, xconfig or gconfig, and saving
the .config file more than once caused data loss, where a .config file
that contained only comments would be written to disk starting from the
second save operation.
This bug manifests itself because the SYMBOL_WRITTEN flag is never
cleared after the first call to conf_write, and subsequent calls to
conf_write then skip all of the configuration symbols due to the
SYMBOL_WRITTEN flag being set.
This commit resolves this issue by clearing the SYMBOL_WRITTEN flag
from all symbols before conf_write returns.
In nouveau_dmem_pages_alloc(), the drm->dmem->mutex is unlocked before
calling nouveau_dmem_chunk_alloc() as shown when CONFIG_PROVE_LOCKING
is enabled:
In nouveau_conn_reset(), if connector->state is true,
__drm_atomic_helper_connector_destroy_state() will be called,
but the memory pointed by asyc isn't freed. Memory leak happens
in the following function __drm_atomic_helper_connector_reset(),
where newly allocated asyc->state will be assigned to connector->state.
So using nouveau_conn_atomic_destroy_state() instead of
__drm_atomic_helper_connector_destroy_state to free the "old" asyc.
On x86-64, with CONFIG_RETPOLINE=n, GCC's "global common subexpression
elimination" optimization results in ___bpf_prog_run()'s jumptable code
changing from this:
The jumptable address is placed in a register once, at the beginning of
the function. The function execution can then go through multiple
indirect jumps which rely on that same register value. This has a few
issues:
1) Objtool isn't smart enough to be able to track such a register value
across multiple recursive indirect jumps through the jump table.
2) With CONFIG_RETPOLINE enabled, this optimization actually results in
a small slowdown. I measured a ~4.7% slowdown in the test_bpf
"tcpdump port 22" selftest.
This slowdown is actually predicted by the GCC manual:
Note: When compiling a program using computed gotos, a GCC
extension, you may get better run-time performance if you
disable the global common subexpression elimination pass by
adding -fno-gcse to the command line.
So just disable the optimization for this function.
Fixes: e55a73251da3 ("bpf: Fix ORC unwinding in non-JIT BPF code") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/30c3ca29ba037afcbd860a8672eef0021addf9fe.1563413318.git.jpoimboe@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log