Paul Kocialkowski [Thu, 3 Nov 2022 16:31:00 +0000 (16:31 +0000)]
media: sun6i-csi: Introduce bridge format structure, list and helper
Introduce a more informative format list for the bridge, with
information about how to configure the input. This separation will
later be useful when using the bridge standalone (without capture)
for the isp workflow.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:55 +0000 (16:30 +0000)]
media: sun6i-csi: Rework capture format management with helper
Remove the need for local copies of the v4l2 format and add a common
helper to prepare a format compatible with the driver, using the
relevant v4l2 helpers.
Report a raw colorspace for bayer-encoded pixel formats instead of SRGB.
Also cleanup the size bound defines while at it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:54 +0000 (16:30 +0000)]
media: sun6i-csi: Move register configuration to capture
Continue moving things over to capture in tidy helpers.
Also take the occasion to remove the config struct, which is
unwelcome redundancy and use the capture helpers instead.
The code is only adapted to reflect the removal of the config
structure. No functional change intended.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:51 +0000 (16:30 +0000)]
media: sun6i-csi: Implement address configuration without indirection
Instead of calculating the planar_offset at one point and using it
later in a dedicated function, reimplement address configuration
with v4l2 format info in the buffer_configure function.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This cleans up the register definitions a bit, adds a prefix, remove masks.
Registers are now fully defined, some additional fields were added when
needed. New format definitions are added for future use.
Some fields are wrongly defined (inverted) in Allwinner literature
(e.g. field vs frame prefixes), which is quite misleading. They are
now corrected to reflect their actual behavior.
This should only be a cosmetic commit. No functional change intended.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:48 +0000 (16:30 +0000)]
media: sun6i-csi: Add capture state using vsync for page flip
The current implementation requires up to 3 buffers to properly
implement page flipping without losing frames: one is configured
before the video stream is started, one just after that and page
flipping is synchronized to the frame done interrupt. The comment in
the code mentions that "CSI will lookup the next dma buffer for next
frame before the current frame done IRQ triggered".
Based on observations of the CSI unit behavior, it seems that the
buffer DMA address is sampled when the frame scan begins (in addition
to starting the stream), which corresponds to the vblank interrupt
that hits just before the frame-done interrupt of the previous frame.
As a result, the address configured at the frame done interrupt is not
actually used for the next frame but for the one after that.
This proposal changes the page flipping sync point to the vsync
interrupt, which allows the DMA address to be sampled for the next
frame instead and allows operating with only two buffers.
In addition to the change in the sync point, the code is refactored
to introduce a notion of state that clarifies tracking of the buffers
with tidy functions.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:47 +0000 (16:30 +0000)]
media: sun6i-csi: Rename sun6i_video to sun6i_csi_capture
In an effort to distinguish between the core csi engine (to be
represented as the bridge) and the dma engine (the capture video
device), rename the video component to capture, with the appropriate
prefix. No functional change intended.
Paul Kocialkowski [Thu, 3 Nov 2022 16:30:46 +0000 (16:30 +0000)]
media: sun6i-csi: Add bridge v4l2 subdev with port management
Introduce a bridge v4l2 subdev to prepare for separation between the
processing part (bridge) and the dma engine, which is required to
properly support ths isp workflow later on.
Currently the bridge just manages fwnode mapping to media pads,
using an async notifier (which was previously in the main code).
The s_stream video op just forwards to the connected v4l2 subdev
(sensor or MIPI CSI-2 bridge).
The video capture device is now registered after the bridge and
attaches to it with a media link.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:56 +0000 (17:08 +0100)]
media: i2c: ov9282: Action CID_VBLANK when set.
Programming the sensor with TIMING_VTS (aka LPFR) was done
when triggered by a change in exposure or gain, but not
when V4L2_CID_VBLANK was changed. Dynamic frame rate
changes could therefore not be achieved.
Separate out programming TIMING_VTS so that it is triggered
by set_ctrl(V4L2_CID_VBLANK)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:54 +0000 (17:08 +0100)]
media: i2c: ov9282: Add selection for CSI2 clock mode
The sensor supports either having the CSI2 clock lane free
running, or gated when there is no packet to transmit.
The driver only selected gated (non-continuous) clock mode.
Add code to allow fwnode to configure whether the clock is
gated or free running.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:53 +0000 (17:08 +0100)]
media: i2c: ov9282: Reduce vblank_min values based on testing
The configured vblank_min setting of 151 (meaning VTS of
720 + 151 = 871) is far higher than the setting that works on
the sensor, and there are no obvious restrictions stated in the
datasheet.
Reduce the vblank_min to allow for faster frame rates.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:52 +0000 (17:08 +0100)]
media: i2c: ov9282: Correct HTS register for configured pixel rate
The calculations from pixel rate, width+hblank, and height+vblank
do not give the correct framerate - it's half the speed it should
be.
The datasheet lists the default for the TIMING_HTS registers (0x380c/d)
as being 0x2d8 (728) which is less than the width of the image, so
the units clearly can't be pixels.
If TIMING_HTS is considered to be units of 2-pixels, then the
resulting value of 0x5b0 (1456) makes all the calculations correct.
This driver is reporting an HBLANK value of 250, with an image width
of 1280, so TIMING_HTS is 1530 (0x5fa) pixels. However it was also
setting the register to 0x5fa, thereby not taking into account it
being units of 2-pixels.
Correct the register value to 0x2fd so that all the timing calculations
give the correct results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:50 +0000 (17:08 +0100)]
media: i2c: ov9282: Remove pixel rate from mode definition
The pixel rate is determined by the PLL setup in the common
registers, not by the mode specific registers, therefore
remove it from the mode definition and define it for all modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:48 +0000 (17:08 +0100)]
media: i2c: ov9282: Split registers into common and mode specific
Currently only one mode is supported, so all registers were
dropped in one list.
In preparation for adding more modes, split out the common registers
from those which configure the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Fri, 28 Oct 2022 16:08:47 +0000 (17:08 +0100)]
media: i2c: ov9282: Remove duplication of registers
TIMING_VTS (registers 0x380e/f), EXPOSURE (registers
0x3500/1/2), and GAIN (0x3509) are all set from
ov9282_update_exp_gain as part of the control handler,
therefore they do not need to be in the main list of
registers.
Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Lad Prabhakar [Mon, 31 Oct 2022 23:21:58 +0000 (23:21 +0000)]
media: dt-bindings: ov5645: Convert OV5645 binding to a schema
Convert the simple OV5645 Device Tree binding to json-schema.
The previous binding marked the below properties as required which was a
driver requirement and not the device requirement so just drop them from
the required list during the conversion.
- clock-frequency
- enable-gpios
- reset-gpios
Also drop the "clock-names" property as we have a single clock source for
the sensor and the driver has been updated to drop the clk referencing by
name.
Set up the .data parameter of of_device_id to pass a string which
we use to set the media entity name. Once done we can add in imx577 as a
compatible chips with the media names reflecting the directed compat string.
Cc: sakari.ailus@iki.fi Cc: dave.stevenson@raspberrypi.com Cc: jacopo@jmondi.org Cc: "Paul J. Murphy" <paul.j.murphy@intel.com> Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Merge tag 'br-v6.2e' of git://linuxtv.org/hverkuil/media_tree into media_stage
Tag branch
* tag 'br-v6.2e' of git://linuxtv.org/hverkuil/media_tree: (29 commits)
media: davinci/vpbe: Fix a typo ("defualt_mode")
media: sun6i-csi: Remove unnecessary print function dev_err()
media: Documentation: Drop deprecated bytesused == 0
media: platform: exynos4-is: fix return value check in fimc_md_probe()
media: dvb-core: remove variable n, turn for-loop to while-loop
media: vivid: fix compose size exceed boundary
media: rkisp1: make const arrays ae_wnd_num and hist_wnd_num static
media: dvb-core: Fix UAF due to refcount races at releasing
media: rkvdec: Add required padding
media: aspeed: Extend debug message
media: aspeed: Support aspeed mode to reduce compressed data
media: Documentation: aspeed-video: Add user documentation for the aspeed-video driver
media: v4l2-ctrls: Reserve controls for ASPEED
media: v4l: Add definition for the Aspeed JPEG format
staging: media: tegra-video: fix device_node use after free
staging: media: tegra-video: fix chan->mipi value on error
media: cedrus: initialize controls a bit later
media: cedrus: prefer untiled capture format
media: cedrus: Remove cedrus_codec enum
media: cedrus: set codec ops immediately
...
Merge tag 'tag-venus-for-v6.2' of git://linuxtv.org/svarbanov/media_tree into media_stage
Venus updates for v6.2
* tag 'tag-venus-for-v6.2' of git://linuxtv.org/svarbanov/media_tree:
venus: pm_helpers: Fix error check in vcodec_domains_get()
venus: firmware: Correct assertion of reset bit on remote processor
venus: firmware: Correct non-pix start and end addresses
venus: firmware: Correct reset bit
MAINTAINERS: Change email for Venus driver
MAINTAINERS: Add Vikash as VENUS video driver co-maintainer
Merge git://linuxtv.org/sailus/media_tree into media_stage
* git://linuxtv.org/sailus/media_tree: (47 commits)
media: i2c: ov4689: code cleanup
media: ov9650: Drop platform data code path
media: ov7670: Drop unused include
media: ov2640: Drop legacy includes
media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver
media: dt-bindings: add bindings for Toshiba TC358746
phy: dphy: add support to calculate the timing based on hs_clk_rate
phy: dphy: refactor get_default_config
v4l: subdev: Warn if disabling streaming failed, return success
dw9768: Enable low-power probe on ACPI
media: i2c: imx290: Replace GAIN control with ANALOGUE_GAIN
media: i2c: imx290: Add crop selection targets support
media: i2c: imx290: Factor out format retrieval to separate function
media: i2c: imx290: Move registers with fixed value to init array
media: i2c: imx290: Create controls for fwnode properties
media: i2c: imx290: Implement HBLANK and VBLANK controls
media: i2c: imx290: Split control initialization to separate function
media: i2c: imx290: Fix max gain value
media: i2c: imx290: Add exposure time control
media: i2c: imx290: Define more register macros
...
Vladimir Zapolskiy [Mon, 4 Jul 2022 22:15:48 +0000 (23:15 +0100)]
media: camss: Split power domain management
There are three cases of power domain management on supported platforms:
1) CAMSS on MSM8916, where a single VFE power domain is operated outside
of the camss device driver,
2) CAMSS on MSM8996 and SDM630/SDM660, where two VFE power domains are
managed separately by the camss device driver, the power domains are
linked and unlinked on demand by their functions vfe_pm_domain_on()
and vfe_pm_domain_off() respectively,
3) CAMSS on SDM845 and SM8250 platforms, and there are two VFE power
domains and their parent power domain TITAN_TOP, the latter one
shall be turned on prior to turning on any of VFE power domains.
Due to a previously missing link between TITAN_TOP and VFEx power domains
in the latter case, which is now fixed by [1], it was decided always to
turn on all found VFE power domains and TITAN_TOP power domain, even if
just one particular VFE is needed to be enabled or none of VFE power
domains are required, for instance the latter case is when vfe_lite is in
use. This misusage becomes more incovenient and clumsy, if next generations
are to be supported, for instance CAMSS on SM8450 has three VFE power
domains.
The change splits the power management support for platforms with TITAN_TOP
parent power domain, and, since 'power-domain-names' property is not
present in camss device tree nodes, the assumption is that the first
N power domains from the 'power-domains' list correspond to VFE power
domains, and, if the number of power domains is greater than number of
non-lite VFEs, then the last power domain from the list is the TITAN_TOP
power domain.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vladimir Zapolskiy [Mon, 4 Jul 2022 22:15:47 +0000 (23:15 +0100)]
media: camss: Collect information about a number of lite VFEs
VFE lite IPs are found on CAMSS with TITAN_TOP power domains, and in
some aspects these types of VFEs are different, in particular there
is no need to enable VFE power domains to operate over VFE lite IPs.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vladimir Zapolskiy [Mon, 4 Jul 2022 22:08:14 +0000 (23:08 +0100)]
media: camss: Do not attach an already attached power domain on MSM8916 platform
The change to dynamically allocated power domains neglected a case of
CAMSS on MSM8916 platform, where a single VFE power domain is neither
attached, linked or managed in runtime in any way explicitly.
This is a special case and it shall be kept as is, because the power
domain management is done outside of the driver, and it's very different
in comparison to all other platforms supported by CAMSS.
Fixes: 6b1814e26989 ("media: camss: Allocate power domain resources dynamically") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vladimir Zapolskiy [Mon, 4 Jul 2022 09:44:37 +0000 (10:44 +0100)]
media: camss: Clean up received buffers on failed start of streaming
It is required to return the received buffers, if streaming can not be
started. For instance media_pipeline_start() may fail with EPIPE, if
a link validation between entities is not passed, and in such a case
a user gets a kernel warning:
The fix is to correct the error path in video_start_streaming() of camss.
Fixes: 0ac2586c410f ("media: camss: Add files which handle the video device nodes") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Linus Torvalds [Sun, 6 Nov 2022 21:09:52 +0000 (13:09 -0800)]
Merge tag 'cxl-fixes-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"Several fixes for CXL region creation crashes, leaks and failures.
This is mainly fallout from the original implementation of dynamic CXL
region creation (instantiate new physical memory pools) that arrived
in v6.0-rc1.
Given the theme of "failures in the presence of pass-through decoders"
this also includes new regression test infrastructure for that case.
Summary:
- Fix region creation crash with pass-through decoders
- Fix region creation crash when no decoder allocation fails
- Fix region creation crash when scanning regions to enforce the
increasing physical address order constraint that CXL mandates
- Fix a memory leak for cxl_pmem_region objects, track 1:N instead of
1:1 memory-device-to-region associations.
- Fix a memory leak for cxl_region objects when regions with active
targets are deleted
- Fix assignment of NUMA nodes to CXL regions by CFMWS (CXL Window)
emulated proximity domains.
- Fix region creation failure for switch attached devices downstream
of a single-port host-bridge
- Fix false positive memory leak of cxl_region objects by recycling
recently used region ids rather than freeing them
- Add regression test infrastructure for a pass-through decoder
configuration
- Fix some mailbox payload handling corner cases"
* tag 'cxl-fixes-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/region: Recycle region ids
cxl/region: Fix 'distance' calculation with passthrough ports
tools/testing/cxl: Add a single-port host-bridge regression config
tools/testing/cxl: Fix some error exits
cxl/pmem: Fix cxl_pmem_region and cxl_memdev leak
cxl/region: Fix cxl_region leak, cleanup targets at region delete
cxl/region: Fix region HPA ordering validation
cxl/pmem: Use size_add() against integer overflow
cxl/region: Fix decoder allocation crash
ACPI: NUMA: Add CXL CFMWS 'nodes' to the possible nodes set
cxl/pmem: Fix failure to account for 8 byte header for writes to the device LSA.
cxl/region: Fix null pointer dereference due to pass through decoder commit
cxl/mbox: Add a check on input payload size
Linus Torvalds [Sun, 6 Nov 2022 20:59:12 +0000 (12:59 -0800)]
Merge tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix two regressions:
- Commit 54cc3dbfc10d ("hwmon: (pmbus) Add regulator supply into
macro") resulted in regulator undercount when disabling regulators.
Revert it.
- The thermal subsystem rework caused the scmi driver to no longer
register with the thermal subsystem because index values no longer
match. To fix the problem, the scmi driver now directly registers
with the thermal subsystem, no longer through the hwmon core"
* tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
Revert "hwmon: (pmbus) Add regulator supply into macro"
hwmon: (scmi) Register explicitly with Thermal Framework
Linus Torvalds [Sun, 6 Nov 2022 20:41:32 +0000 (12:41 -0800)]
Merge tag 'perf_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Add Cooper Lake's stepping to the PEBS guest/host events isolation
fixed microcode revisions checking quirk
- Update Icelake and Sapphire Rapids events constraints
- Use the standard energy unit for Sapphire Rapids in RAPL
- Fix the hw_breakpoint test to fail more graciously on !SMP configs
* tag 'perf_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
perf/x86/intel: Fix pebs event constraints for SPR
perf/x86/intel: Fix pebs event constraints for ICL
perf/x86/rapl: Use standard Energy Unit for SPR Dram RAPL domain
perf/hw_breakpoint: test: Skip the test if dependencies unmet
Linus Torvalds [Sun, 6 Nov 2022 20:36:47 +0000 (12:36 -0800)]
Merge tag 'x86_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add new Intel CPU models
- Enforce that TDX guests are successfully loaded only on TDX hardware
where virtualization exception (#VE) delivery on kernel memory is
disabled because handling those in all possible cases is "essentially
impossible"
- Add the proper include to the syscall wrappers so that BTF can see
the real pt_regs definition and not only the forward declaration
* tag 'x86_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add several Intel server CPU model numbers
x86/tdx: Panic on bad configs that #VE on "private" memory access
x86/tdx: Prepare for using "INFO" call for a second purpose
x86/syscall: Include asm/ptrace.h in syscall_wrapper header
Linus Torvalds [Sun, 6 Nov 2022 20:23:10 +0000 (12:23 -0800)]
Merge tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Use POSIX-compatible grep options
- Document git-related tips for reproducible builds
- Fix a typo in the modpost rule
- Suppress SIGPIPE error message from gcc-ar and llvm-ar
- Fix segmentation fault in the menuconfig search
* tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: fix segmentation fault in menuconfig search
kbuild: fix SIGPIPE error message for AR=gcc-ar and AR=llvm-ar
kbuild: fix typo in modpost
Documentation: kbuild: Add description of git for reproducible builds
kbuild: use POSIX-compatible grep option
Linus Torvalds [Sun, 6 Nov 2022 18:46:59 +0000 (10:46 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix the pKVM stage-1 walker erronously using the stage-2 accessor
- Correctly convert vcpu->kvm to a hyp pointer when generating an
exception in a nVHE+MTE configuration
- Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them
- Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
- Document the boot requirements for FGT when entering the kernel at
EL1
x86:
- Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
- Make argument order consistent for kvcalloc()
- Userspace API fixes for DEBUGCTL and LBRs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix a typo about the usage of kvcalloc()
KVM: x86: Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
KVM: VMX: Ignore guest CPUID for host userspace writes to DEBUGCTL
KVM: VMX: Fold vmx_supported_debugctl() into vcpu_supported_debugctl()
KVM: VMX: Advertise PMU LBRs if and only if perf supports LBRs
arm64: booting: Document our requirements for fine grained traps with SME
KVM: arm64: Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
KVM: Check KVM_CAP_DIRTY_LOG_{RING, RING_ACQ_REL} prior to enabling them
KVM: arm64: Fix bad dereference on MTE-enabled systems
KVM: arm64: Use correct accessor to parse stage-1 PTEs
Linus Torvalds [Sun, 6 Nov 2022 18:42:29 +0000 (10:42 -0800)]
Merge tag 'for-linus-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"One fix for silencing a smatch warning, and a small cleanup patch"
* tag 'for-linus-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: simplify sysenter and syscall setup
x86/xen: silence smatch warning in pmu_msr_chk_emulated()
Linus Torvalds [Sun, 6 Nov 2022 18:30:29 +0000 (10:30 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a number of bugs, including some regressions, the most serious of
which was one which would cause online resizes to fail with file
systems with metadata checksums enabled.
Also fix a warning caused by the newly added fortify string checker,
plus some bugs that were found using fuzzed file systems"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix fortify warning in fs/ext4/fast_commit.c:1551
ext4: fix wrong return err in ext4_load_and_init_journal()
ext4: fix warning in 'ext4_da_release_space'
ext4: fix BUG_ON() when directory entry has invalid rec_len
ext4: update the backup superblock's at the end of the online resize
Linus Torvalds [Sun, 6 Nov 2022 18:19:39 +0000 (10:19 -0800)]
Merge tag '6.1-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One symlink handling fix and two fixes foir multichannel issues with
iterating channels, including for oplock breaks when leases are
disabled"
* tag '6.1-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix use-after-free on the link name
cifs: avoid unnecessary iteration of tcp sessions
cifs: always iterate smb sessions using primary channel
Linus Torvalds [Sun, 6 Nov 2022 17:57:38 +0000 (09:57 -0800)]
Merge tag 'trace-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull `lTracing fixes for 6.1-rc3:
- Fixed NULL pointer dereference in the ring buffer wait-waiters code
for machines that have less CPUs than what nr_cpu_ids returns.
The buffer array is of size nr_cpu_ids, but only the online CPUs get
initialized.
- Fixed use after free call in ftrace_shutdown.
- Fix accounting of if a kprobe is enabled
- Fix NULL pointer dereference on error path of fprobe rethook_alloc().
- Fix unregistering of fprobe_kprobe_handler
- Fix memory leak in kprobe test module
* tag 'trace-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
tracing/fprobe: Fix to check whether fprobe is registered correctly
fprobe: Check rethook_alloc() return in rethook initialization
kprobe: reverse kp->flags when arm_kprobe failed
ftrace: Fix use-after-free for dynamic ftrace_ops
ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()
Jason Yan [Tue, 25 Oct 2022 04:02:06 +0000 (12:02 +0800)]
ext4: fix wrong return err in ext4_load_and_init_journal()
The return value is wrong in ext4_load_and_init_journal(). The local
variable 'err' need to be initialized before goto out. The original code
in __ext4_fill_super() is fine because it has two return values 'ret'
and 'err' and 'ret' is initialized as -EINVAL. After we factor out
ext4_load_and_init_journal(), this code is broken. So fix it by directly
returning -EINVAL in the error handler path.
Cc: stable@kernel.org Fixes: 9c1dd22d7422 ("ext4: factor out ext4_load_and_init_journal()") Signed-off-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20221025040206.3134773-1-yanaijie@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Above issue may happens as follows:
ext4_da_write_begin
ext4_create_inline_data
ext4_clear_inode_flag(inode, EXT4_INODE_EXTENTS);
ext4_set_inode_flag(inode, EXT4_INODE_INLINE_DATA);
__ext4_ioctl
ext4_ext_migrate -> will lead to eh->eh_entries not zero, and set extent flag
ext4_da_write_begin
ext4_da_convert_inline_data_to_extent
ext4_da_write_inline_data_begin
ext4_da_map_blocks
ext4_insert_delayed_block
if (!ext4_es_scan_clu(inode, &ext4_es_is_delonly, lblk))
if (!ext4_es_scan_clu(inode, &ext4_es_is_mapped, lblk))
ext4_clu_mapped(inode, EXT4_B2C(sbi, lblk)); -> will return 1
allocated = true;
ext4_es_insert_delayed_block(inode, lblk, allocated);
ext4_writepages
mpage_map_and_submit_extent(handle, &mpd, &give_up_on_write); -> return -ENOSPC
mpage_release_unused_pages(&mpd, give_up_on_write); -> give_up_on_write == 1
ext4_es_remove_extent
ext4_da_release_space(inode, reserved);
if (unlikely(to_free > ei->i_reserved_data_blocks))
-> to_free == 1 but ei->i_reserved_data_blocks == 0
-> then trigger warning as above
To solve above issue, forbid inode do migrate which has inline data.
Cc: stable@kernel.org Reported-by: syzbot+c740bb18df70ad00952e@syzkaller.appspotmail.com Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20221018022701.683489-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Luís Henriques [Wed, 12 Oct 2022 13:13:30 +0000 (14:13 +0100)]
ext4: fix BUG_ON() when directory entry has invalid rec_len
The rec_len field in the directory entry has to be a multiple of 4. A
corrupted filesystem image can be used to hit a BUG() in
ext4_rec_len_to_disk(), called from make_indexed_dir().
Linus Torvalds [Sat, 5 Nov 2022 19:10:25 +0000 (12:10 -0700)]
Merge tag 'acpi-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Add StorageD3Enable quirk for Dell Inspiron 16 5625 (Mario
Limonciello)"
* tag 'acpi-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: x86: Add another system to quirk list for forcing StorageD3Enable
- Explicitly clear the last request in a chain when the plug is
flushed, as it may have already been issued (Al)
* tag 'block-6.1-2022-11-05' of git://git.kernel.dk/linux:
block: blk_add_rq_to_plug(): clear stale 'last' after flush
blk-mq: Fix kmemleak in blk_mq_init_allocated_queue
block: Fix possible memory leak for rq_wb on add_disk failure
ublk_drv: add ublk_queue_cmd() for cleanup
ublk_drv: avoid to touch io_uring cmd in blk_mq io path
ublk_drv: comment on ublk_driver entry of Kconfig
ublk_drv: return flag of UBLK_F_URING_CMD_COMP_IN_TASK in case of module
When opened a symlink, link name is from 'inode->i_link', but it may be
reset to a new value when revalidate the dentry. If some processes get the
link name on the race scenario, then UAF will happen on link name.
Fix this by implementing 'get_link' interface to duplicate the link name.
Fixes: 76894f3e2f71 ("cifs: improve symlink handling for smb2+") Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
Shyam Prasad N [Fri, 28 Oct 2022 10:01:45 +0000 (10:01 +0000)]
cifs: avoid unnecessary iteration of tcp sessions
In a few places, we do unnecessary iterations of
tcp sessions, even when the server struct is provided.
The change avoids it and uses the server struct provided.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
Shyam Prasad N [Fri, 28 Oct 2022 09:52:26 +0000 (09:52 +0000)]
cifs: always iterate smb sessions using primary channel
smb sessions and tcons currently hang off primary channel only.
Secondary channels have the lists as empty. Whenever there's a
need to iterate sessions or tcons, we should use the list in the
corresponding primary channel.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
Linus Torvalds [Sat, 5 Nov 2022 02:52:24 +0000 (19:52 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Avoid kprobe recursion when cortex_a76_erratum_1463225_debug_handler()
is not inlined (change to __always_inline).
- Fix the visibility of compat hwcaps, broken by recent changes to
consolidate the visibility of hwcaps and the user-space view of the
ID registers.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpufeature: Fix the visibility of compat hwcaps
arm64: entry: avoid kprobe recursion
Zev Weiss reports that the reverted patch may cause a regulator
undercount. Here is his report:
... having regulator-dummy set as a supply on my PMBus regulators
(instead of having them as their own top-level regulators without
an upstream supply) leads to enable-count underflow errors when
disabling them:
# echo 0 > /sys/bus/platform/devices/efuse01/state
[ 906.094477] regulator-dummy: Underflow of regulator enable count
[ 906.100563] Failed to disable vout: -EINVAL
[ 136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22
Zev reports that reverting the patch fixes the problem. So let's do that
for now.
Cristian Marussi [Mon, 31 Oct 2022 11:40:18 +0000 (11:40 +0000)]
hwmon: (scmi) Register explicitly with Thermal Framework
Available sensors are enumerated and reported by the SCMI platform server
using a 16bit identification number; not all such sensors are of a type
supported by hwmon subsystem and, among the supported ones, only a subset
could be temperature sensors that have to be registered with the Thermal
Framework.
Potential clashes between hwmon channels indexes and the underlying real
sensors IDs do not play well with the hwmon<-->thermal bridge automatic
registration routines and could need a sensible number of fake dummy
sensors to be made up in order to keep indexes and IDs in sync.
Avoid to use the hwmon<-->thermal bridge dropping the HWMON_C_REGISTER_TZ
attribute and instead explicit register temperature sensors directly with
the Thermal Framework.
Dan Williams [Fri, 4 Nov 2022 00:31:00 +0000 (17:31 -0700)]
cxl/region: Recycle region ids
At region creation time the next region-id is atomically cached so that
there is predictability of region device names. If that region is
destroyed and then a new one is created the region id increments. That
ends up looking like a memory leak, or is otherwise surprising that
identifiers roll forward even after destroying all previously created
regions.
Try to reuse rather than free old region ids at region release time.
While this fixes a cosmetic issue, the needlessly advancing memory
region-id gives the appearance of a memory leak, hence the "Fixes" tag,
but no "Cc: stable" tag.
Cc: Ben Widawsky <bwidawsk@kernel.org> Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com> Fixes: 779dd20cfb56 ("cxl/region: Add region creation support") Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Link: https://lore.kernel.org/r/166752186062.947915.13200195701224993317.stgit@dwillia2-xfh.jf.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 4 Nov 2022 00:30:54 +0000 (17:30 -0700)]
cxl/region: Fix 'distance' calculation with passthrough ports
When programming port decode targets, the algorithm wants to ensure that
two devices are compatible to be programmed as peers beneath a given
port. A compatible peer is a target that shares the same dport, and
where that target's interleave position also routes it to the same
dport. Compatibility is determined by the device's interleave position
being >= to distance. For example, if a given dport can only map every
Nth position then positions less than N away from the last target
programmed are incompatible.
The @distance for the host-bridge's cxl_port in a simple dual-ported
host-bridge configuration with 2 direct-attached devices is 1, i.e. An
x2 region divided by 2 dports to reach 2 region targets.
An x4 region under an x2 host-bridge would need 2 intervening switches
where the @distance at the host bridge level is 2 (x4 region divided by
2 switches to reach 4 devices).
However, the distance between peers underneath a single ported
host-bridge is always zero because there is no limit to the number of
devices that can be mapped. In other words, there are no decoders to
program in a passthrough, all descendants are mapped and distance only
starts matters for the intervening descendant ports of the passthrough
port.
Add tracking for the number of dports mapped to a port, and use that to
detect the passthrough case for calculating @distance.
Dan Williams [Fri, 4 Nov 2022 00:30:48 +0000 (17:30 -0700)]
tools/testing/cxl: Add a single-port host-bridge regression config
Jonathan reports that region creation fails when a single-port
host-bridge connects to a multi-port switch. Mock up that configuration
so a fix can be tested and regression tested going forward.
Dan Williams [Fri, 4 Nov 2022 00:30:36 +0000 (17:30 -0700)]
cxl/pmem: Fix cxl_pmem_region and cxl_memdev leak
When a cxl_nvdimm object goes through a ->remove() event (device
physically removed, nvdimm-bridge disabled, or nvdimm device disabled),
then any associated regions must also be disabled. As highlighted by the
cxl-create-region.sh test [1], a single device may host multiple
regions, but the driver was only tracking one region at a time. This
leads to a situation where only the last enabled region per nvdimm
device is cleaned up properly. Other regions are leaked, and this also
causes cxl_memdev reference leaks.
Fix the tracking by allowing cxl_nvdimm objects to track multiple region
associations.
Dan Williams [Fri, 4 Nov 2022 00:30:30 +0000 (17:30 -0700)]
cxl/region: Fix cxl_region leak, cleanup targets at region delete
When a region is deleted any targets that have been previously assigned
to that region hold references to it. Trigger those references to
drop by detaching all targets at unregister_region() time.
Otherwise that region object will leak as userspace has lost the ability
to detach targets once region sysfs is torn down.
store_targetN+0x655/0x1740:
alloc_region_ref at drivers/cxl/core/region.c:676
(inlined by) cxl_port_attach_region at drivers/cxl/core/region.c:850
(inlined by) cxl_region_attach at drivers/cxl/core/region.c:1290
(inlined by) attach_target at drivers/cxl/core/region.c:1410
(inlined by) store_targetN at drivers/cxl/core/region.c:1453
Linus Torvalds [Fri, 4 Nov 2022 22:05:42 +0000 (15:05 -0700)]
Merge tag 'xfs-6.1-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Dave and I had thought that this would be a very quiet cycle, but we
thought wrong.
At first there were the usual trickle of minor bugfixes, but then
Zorro pulled -rc1 and noticed complaints about the stronger memcpy
checks w.r.t. flex arrays.
Analyzing how to fix that revealed a bunch of validation gaps in
validating ondisk log items during recovery, and then a customer hit
an infinite loop in the refcounting code on a corrupt filesystem.
So. This largeish batch of fixes addresses all those problems, I hope.
Summary:
- Fix a UAF bug during log recovery
- Fix memory leaks when mount fails
- Detect corrupt bestfree information in a directory block
- Fix incorrect return value type for the dax page fault handlers
- Fix fortify complaints about memcpy of xfs log item objects
- Strengthen inadequate validation of recovered log items
- Fix infinite loop problems in the refcount code if the refcount
btree node block keys are corrupt
- Fix infinite loop problems in the refcount code if the refcount
btree records suffer MSB bitflips
- Add more sanity checking to continued defer ops to prevent
overflows from one AG to the next or off EOFS"
* tag 'xfs-6.1-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (28 commits)
xfs: rename XFS_REFC_COW_START to _COWFLAG
xfs: fix uninitialized list head in struct xfs_refcount_recovery
xfs: fix agblocks check in the cow leftover recovery function
xfs: check record domain when accessing refcount records
xfs: remove XFS_FIND_RCEXT_SHARED and _COW
xfs: refactor domain and refcount checking
xfs: report refcount domain in tracepoints
xfs: track cow/shared record domains explicitly in xfs_refcount_irec
xfs: refactor refcount record usage in xchk_refcountbt_rec
xfs: dump corrupt recovered log intent items to dmesg consistently
xfs: move _irec structs to xfs_types.h
xfs: actually abort log recovery on corrupt intent-done log items
xfs: check deferred refcount op continuation parameters
xfs: refactor all the EFI/EFD log item sizeof logic
xfs: create a predicate to verify per-AG extents
xfs: fix memcpy fortify errors in EFI log format copying
xfs: make sure aglen never goes negative in xfs_refcount_adjust_extents
xfs: fix memcpy fortify errors in RUI log format copying
xfs: fix memcpy fortify errors in CUI log format copying
xfs: fix memcpy fortify errors in BUI log format copying
...
Linus Torvalds [Fri, 4 Nov 2022 21:37:25 +0000 (14:37 -0700)]
Merge tag 'efi-fixes-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- A pair of tweaks to the EFI random seed code so that externally
provided version of this config table are handled more robustly
- Another fix for the v6.0 EFI variable refactor that turned out to
break Apple machines which don't provide QueryVariableInfo()
- Add some guard rails to the EFI runtime service call wrapper so we
can recover from synchronous exceptions caused by firmware
* tag 'efi-fixes-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
arm64: efi: Recover from synchronous exceptions occurring in firmware
efi: efivars: Fix variable writes with unsupported query_variable_store()
efi: random: Use 'ACPI reclaim' memory for random seed
efi: random: reduce seed size to 32 bytes
efi/tpm: Pass correct address to memblock_reserve
Linus Torvalds [Fri, 4 Nov 2022 21:13:12 +0000 (14:13 -0700)]
Merge tag 'soc-fixes-6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are not a lot of important fixes for the soc tree yet this time,
but it's time to upstream what I got so far:
- DT Fixes for Arm Juno and ST-Ericsson Ux500 to add missing critical
temperature points
- A number of fixes for the Arm SCMI firmware, addressing correctness
issues in the code, in particular error handling and resource
leaks.
- One error handling fix for the new i.MX93 power domain driver
- Several devicetree fixes for NXP i.MX6/8/9 and Layerscape chips,
fixing incorrect or missing DT properties for MDIO controller
nodes, CPLD, USB and regulators for various boards, as well as some
fixes for DT schema checks.
- MAINTAINERS file updates for HiSilicon LPC Bus and Broadcom git
URLs"
* tag 'soc-fixes-6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
arm64: dts: juno: Add thermal critical trip points
firmware: arm_scmi: Fix deferred_tx_wq release on error paths
firmware: arm_scmi: Fix devres allocation device in virtio transport
firmware: arm_scmi: Make Rx chan_setup fail on memory errors
firmware: arm_scmi: Make tx_prepare time out eventually
firmware: arm_scmi: Suppress the driver's bind attributes
firmware: arm_scmi: Cleanup the core driver removal callback
MAINTAINERS: Update HiSilicon LPC BUS Driver maintainer
ARM: dts: ux500: Add trips to battery thermal zones
arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
soc: imx: imx93-pd: Fix the error handling path of imx93_pd_probe()
arm64: dts: imx93: correct gpio-ranges
arm64: dts: imx93: correct s4mu interrupt names
dt-bindings: power: gpcv2: add power-domains property
arm64: dts: imx8: correct clock order
ARM: dts: imx6dl-yapp4: Do not allow PM to switch PU regulator off on Q/QP
ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
arm64: dts: imx8mn: Correct the usb power domain
...
Tony Luck [Thu, 3 Nov 2022 20:33:10 +0000 (13:33 -0700)]
x86/cpu: Add several Intel server CPU model numbers
These servers are all on the public versions of the roadmap. The model
numbers for Grand Ridge, Granite Rapids, and Sierra Forest were included
in the September 2022 edition of the Instruction Set Extensions document.
Linus Torvalds [Fri, 4 Nov 2022 18:31:41 +0000 (11:31 -0700)]
Merge tag 'drm-fixes-2022-11-04-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This is the weekly fixes for rc4. Misc fixes across rockchip, imx,
amdgpu and i915.
The biggest change is for amdkfd where the trap handler needs an
updated fw from a header which makes it a bit larger. I hadn't noticed
this particular file before so I'm going to figure out what the magic
is for, but the fix should be fine for now.
* tag 'drm-fixes-2022-11-04-1' of git://anongit.freedesktop.org/drm/drm: (35 commits)
drm/amdkfd: update GFX11 CWSR trap handler
drm/amd/display: Investigate tool reported FCLK P-state deviations
drm/amd/display: Add DSC delay factor workaround
drm/amd/display: Round up DST_after_scaler to nearest int
drm/amd/display: Use forced DSC bpp in DML
drm/amd/display: Fix DCN32 DSC delay calculation
drm/amdgpu: Disable GPU reset on SRIOV before remove pci.
drm/amdgpu: disable GFXOFF during compute for GFX11
drm/amd: Fail the suspend if resources can't be evicted
drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()
drm/amdgpu: correct MES debugfs versions
drm/amdgpu: set fb_modifiers_not_supported in vkms
drm/amd/display: cursor update command incomplete
drm/amd/display: Enable timing sync on DCN32
drm/amd/display: Set memclk levels to be at least 1 for dcn32
drm/amd/display: Update latencies on DCN321
drm/amd/display: Limit dcn32 to 1950Mhz display clock
drm/amd/display: Ignore Cable ID Feature
drm/amd/display: Update DSC capabilitie for DCN314
drm/imx: imx-tve: Fix return type of imx_tve_connector_mode_valid
...
Linus Torvalds [Fri, 4 Nov 2022 18:22:44 +0000 (11:22 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Fixes in clk drivers and some clk rate range fixes in the core as
well:
- Make sure the struct clk_rate_request is more sane
- Remove a WARN_ON that was triggering for clks with no parents that
can change frequency
- Fix bad i2c bus transactions on Renesas rs9
- Actually return an error in clk_mt8195_topck_probe() on an error
path
- Keep the GPU memories powered while the clk isn't enabled on
Qualcomm's sc7280 SoC
- Fix the parent clk for HSCIF modules on Renesas' R-Car V4H SoC"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: Update the force mem core bit for GPU clocks
clk: Initialize max_rate in struct clk_rate_request
clk: Initialize the clk_rate_request even if clk_core is NULL
clk: Remove WARN_ON NULL parent in clk_core_init_rate_req()
clk: renesas: r8a779g0: Fix HSCIF parent clocks
clk: renesas: r8a779g0: Add SASYNCPER clocks
clk: mediatek: clk-mt8195-topckgen: Fix error return code in clk_mt8195_topck_probe()
clk: sifive: select by default if SOC_SIFIVE
clk: rs9: Fix I2C accessors
Laurent Pinchart [Sun, 9 Oct 2022 21:35:09 +0000 (00:35 +0300)]
media: Documentation: Drop deprecated bytesused == 0
The V4L2 API historically allowed buffers to be queued with bytesused
set to 0 on output devices, in which case the driver would use the
buffer length. This behaviour is deprecated, and videobuf2 prints a
warning message in the kernel log. Drop it from the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Yang Yingliang [Mon, 24 Oct 2022 13:46:50 +0000 (21:46 +0800)]
media: platform: exynos4-is: fix return value check in fimc_md_probe()
devm_pinctrl_get() may return ERR_PTR(-EPROBE_DEFER), add a minus sign
to fix it.
Fixes: 4163851f7b99 ("[media] s5p-fimc: Use pinctrl API for camera ports configuration") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
projects / users / jedix / linux-maple.git / log