Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664b7 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34f7 ("iio: Add support for creating IIO devices via configfs") Reported-by: Miguel Robles <miguel.robles@farole.net> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: Dave Penkler <dpenkler@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt") Reported-by: Alexandre Bailon <abailon@baylibre.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Alexandre Bailon <abailon@baylibre.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.
Devices identified as E7="73 03 28" use slightly modified version of V8
protocol, with lower count per electrode, different offsets, and different
feature bits in OTP data.
Fixes: aeaa881f9b17 ("Input: ALPS - set DualPoint flag for 74 03 28 devices") Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Acked-by: Pali Rohar <pali.rohar@gmail.com> Tested-by: Paul Donohue <linux-kernel@PaulSD.com> Tested-by: Nick Fletcher <nick.m.fletcher@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca2a ("net: filter: simplify socket charging") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by: Doug Berger <opendmb@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c34 ("sock: enable timestamping using control messages") Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f881e ("net: vrf: ipv6 support for local traffic to
local addresses") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
Added a case for OVS_TUNNEL_KEY_ATTR_PAD to the switch statement
in ip_tun_from_nlattr in order to prevent the default case
returning an error.
Fixes: b46f6ded906e ("libnl: nla_put_be64(): align on a 64-bit area") Signed-off-by: Kris Murphy <kriskend@linux.vnet.ibm.com> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I mistakenly added the code to release sk->sk_frag in
sk_common_release() instead of sk_destruct()
TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call
sk_common_release() at close time, thus leaking one (order-3) page.
iSCSI is using such sockets.
Fixes: 5640f7685831 ("net: use a per task frag allocator") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dealing with ipv6 source tunnel key address attribute
(OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel
dst ip, fix that.
Fixes: 6b26ba3a7d95 ('openvswitch: netlink attributes for IPv6 tunneling') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OLAND 0x1002:0x6604 0x1028:0x066F 0x00 seems to have problems
with higher sclks.
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pids_can_fork() is special in that the css association is guaranteed
to be stable throughout the function and thus doesn't need RCU
protection around task_css access. When determining the css to charge
the pid, task_css_check() is used to override the RCU sanity check.
While adding a warning message on fork rejection from pids limit, 135b8b37bd91 ("cgroup: Add pids controller event when fork fails
because of pid limit") incorrectly added a task_css access which is
neither RCU protected or explicitly annotated. This triggers the
following suspicious RCU usage warning when RCU debugging is enabled.
There's no reason to dereference task_css again here when the
associated css is already available. Fix it by replacing the
task_cgroup() call with css->cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Galbraith <efault@gmx.de> Fixes: 135b8b37bd91 ("cgroup: Add pids controller event when fork fails because of pid limit") Cc: Kenny Yu <kennyyu@fb.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update to pcpu_nr_empty_pop_pages in pcpu_alloc() is currently done
without holding pcpu_lock. This can lead to bad updates to the variable.
Add missing lock calls.
Commit 88ffbf3e03 switches to using rhashtables for glocks, hashing over
the entire struct lm_lockname instead of its individual fields. On some
architectures, struct lm_lockname contains a hole of uninitialized
memory due to alignment rules, which now leads to incorrect hash values.
Get rid of that hole.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: cf7776dc05b8 ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection") Cc: Hansjoerg Lipp <hjlipp@web.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Max, the Windows 2008 R2 chkdsk utility expects
VERIFY_16 to be supported, and does not handle the returned
CHECK_CONDITION properly, resulting in an infinite loop.
There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"
Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)). When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock. That leads to linked list
corruption and eventually a panicked system.
Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.
Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue. This patch has been
tested there successfully.
Signed-off-by: Chris Leech <cleech@redhat.com> Fixes: 659743b02c41 ("[SCSI] libiscsi: Reduce locking contention in fast path") Reported-by: Prashantha Subbarao <psubbara@us.ibm.com> Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following fixes a divide by zero OOPs with TYPE_TAPE
due to pscsi_tape_read_blocksize() failing causing a zero
sd->sector_size being propigated up via dev_attrib.hw_block_size.
It also fixes another long-standing bug where TYPE_TAPE and
TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(),
which does not call scsi_device_get() to take the device
reference. Instead, rename pscsi_create_type_rom() to
pscsi_create_type_nondisk() and use it for all cases.
Finally, also drop a dump_stack() in pscsi_get_blocks() for
non TYPE_DISK, which in modern target-core can get invoked
via target_sense_desc_format() during CHECK_CONDITION.
Neil Brown pointed out a potential deadlock in raid 10 code with
bio_split/chain. The raid1 code could have the same issue, but recent
barrier rework makes it less likely to happen. The deadlock happens in
below sequence:
1. generic_make_request(bio), this will set current->bio_list
2. raid10_make_request will split bio to bio1 and bio2
3. __make_request(bio1), wait_barrer, add underlayer disk bio to
current->bio_list
4. __make_request(bio2), wait_barrer
If raise_barrier happens between 3 & 4, since wait_barrier runs at 3,
raise_barrier waits for IO completion from 3. And since raise_barrier
sets barrier, 4 waits for raise_barrier. But IO from 3 can't be
dispatched because raid10_make_request() doesn't finished yet.
The solution is to adjust the IO ordering. Quotes from Neil:
"
It is much safer to:
if (need to split) {
split = bio_split(bio, ...)
bio_chain(...)
make_request_fn(split);
generic_make_request(bio);
} else
make_request_fn(mddev, bio);
This way we first process the initial section of the bio (in 'split')
which will queue some requests to the underlying devices. These
requests will be queued in generic_make_request.
Then we queue the remainder of the bio, which will be added to the end
of the generic_make_request queue.
Then we return.
generic_make_request() will pop the lower-level device requests off the
queue and handle them first. Then it will process the remainder
of the original bio once the first section has been fully processed.
"
Note, this only happens in read path. In write path, the bio is flushed to
underlaying disks either by blk flush (from schedule) or offladed to raid1/10d.
It's queued in current->bio_list.
Cc: Coly Li <colyli@suse.de> Suggested-by: NeilBrown <neilb@suse.com> Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent toolchains force the TOC to be 256 byte aligned. We need to
enforce this alignment in the zImage linker script, otherwise pointers
to our TOC variables (__toc_start) could be incorrect. If the actual
start of the TOC and __toc_start don't have the same value we crash
early in the zImage wrapper.
Suggested-by: Alan Modra <amodra@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since rpc_task is async, the release function should be called which
will free the impl_id, scope, and owner.
Trond pointed at 2 more problems:
-- use of client pointer after free in the nfs4_exchangeid_release() function
-- cl_count mismatch if rpc_run_task() isn't run
Fixes: 8d89bd70bc9 ("NFS setup async exchange_id") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I can't reproduce this running sparse here. Likewise, "make W=1
net/sunrpc/xprtrdma/verbs.o" never indicated any issue.
A little poking suggests that because the range of its values is
small, gcc can make the actual width of RPCRDMA_MAX_SEND_SGES
smaller than the width of an unsigned integer.
Fixes: 16f906d66cd7 ("xprtrdma: Reduce required number of send SGEs") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While hunting for clues to a use-after-free, Oleg spotted that
perf_event_init_context() can loose an error value with the result
that fork() can succeed even though we did not fully inherit the perf
event context.
Spotted-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: oleg@redhat.com Fixes: 889ff0150661 ("perf/core: Split context's event group list into pinned and non-pinned lists") Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch closes the hole by making perf_event_free_task() destroy the
task <-> ctx relation such that perf_event_release_kernel() will no longer
observe the now dead task.
On those parisc machines which don't provide a software power off
function, the system currently kills the init process at the end of a
shutdown and unexpectedly restarts insteads of halting.
Fix it by adding a loop which will not return.
The previously submitted patch did not resolve the random segmentation
faults observed on the phantom buildd system. There are still
unresolved problems with the Debian 4.8 and 4.9 kernels on C8000.
The attached patch removes the flush of the offset map pages and does a
whole data cache flush for large ranges. No other arch flushes the
offset map in these routines as far as I can tell.
I have not observed any random segmentation faults on rp3440 in two
weeks of testing with 4.10.0 and 4.10.1.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
gcc-7 has an "optimization" pass that completely screws up, and
generates the code expansion for the (impossible) case of calling
ilog2() with a zero constant, even when the code gcc compiles does not
actually have a zero constant.
And we try to generate a compile-time error for anybody doing ilog2() on
a constant where that doesn't make sense (be it zero or negative). So
now gcc7 will fail the build due to our sanity checking, because it
created that constant-zero case that didn't actually exist in the source
code.
There's a whole long discussion on the kernel mailing about how to work
around this gcc bug. The gcc people themselevs have discussed their
"feature" in
but it's all water under the bridge, because while it looked at one
point like it would be solved by the time gcc7 was released, that was
not to be.
So now we have to deal with this compiler braindamage.
And the only simple approach seems to be to just delete the code that
tries to warn about bad uses of ilog2().
So now "ilog2()" will just return 0 not just for the value 1, but for
any non-positive value too.
It's not like I can recall anybody having ever actually tried to use
this function on any invalid value, but maybe the sanity check just
meant that such code never made it out in public.
Reported-by: Laura Abbott <labbott@redhat.com> Cc: John Stultz <john.stultz@linaro.org>, Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_put() we were using immediately released power on the
device, which meant that we were generally turning the device off and
on once per frame. In many profiles I've looked at, that added up to
about 1% of CPU time, but this could get worse in the case of frequent
rendering and readback (as may happen in X rendering). By keeping the
device on until we've been idle for a couple of frames, we drop the
overhead of runtime PM down to sub-.1%.
Signed-off-by: Eric Anholt <eric@anholt.net> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop is scanning until the original max_ip (size of the BO), but
we want to not examine any code after the PROG_END's delay slots.
There was a block trying to do that, except that we had some early
continue statements if the signal wasn't a PROG_END or a BRANCH.
The failure mode would be that a valid shader is rejected because some
undefined memory after the PROG_END slots is parsed as a branch and
the rest of its setup is illegal. I haven't seen this in the wild,
but valgrind was complaining when about this up in the userland
simulator mode.
Signed-off-by: Eric Anholt <eric@anholt.net> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hang if SIGKILL has been sent, but the task is stuck in down_read()
(after do_exit()), even though no task is doing down_write() on the
rwsem in question:
INFO: task libupnp:21868 blocked for more than 120 seconds.
libupnp D 0 21868 1 0x08100008
...
Call Trace:
__schedule()
schedule()
__down_read()
do_exit()
do_group_exit()
__wake_up_parent()
This bug has already been fixed for CONFIG_RWSEM_XCHGADD_ALGORITHM=y in
the following commit:
If one thread mmaps a perf event while another thread in the same mm
is in some context where active_mm != mm (which can happen in the
scheduler, for example), refresh_pce() would write the wrong value
to CR4.PCE. This broke some PAPI tests.
Reported-and-tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bpetkov@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 7911d3f7af14 ("perf/x86: Only allow rdpmc if a perf_event is mapped") Link: http://lkml.kernel.org/r/0c5b38a76ea50e405f9abe07a13dfaef87c173a1.1489694270.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doesn't boot with both PROFILE_ANNOTATED_BRANCHES=y and KASAN=y
options selected. With branch profiling enabled we end up calling
ftrace_likely_update() before kasan_early_init(). ftrace_likely_update() is
built with KASAN instrumentation, so calling it before kasan has been
initialized leads to crash.
Use DISABLE_BRANCH_PROFILING define to make sure that we don't call
ftrace_likely_update() from early code before kasan_early_init().
Subhransu reported that convert_art_to_tsc() isn't working for him.
The ART to TSC relation is only set up for systems which use the refined
TSC calibration. Systems with known TSC frequency (available via CPUID 15)
are not using the refined calibration and therefor the ART to TSC relation
is never established.
Add the setup to the known frequency init path which skips ART
calibration. The init code needs to be duplicated as for systems which use
refined calibration the ART setup must be delayed until calibration has
been done.
The problem has been there since the ART support was introdduced, but only
detected now because Subhransu tested the first time on hardware which has
TSC frequency enumerated via CPUID 15.
Note for stable: The conditional has changed from TSC_RELIABLE to
TSC_KNOWN_FREQUENCY.
[ tglx: Rewrote changelog and identified the proper 'Fixes' commit ]
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
When invalidating guest TLBs, special care must be taken to
actually shoot the guest TLBs and not the host ones if we're
running on a VHE system. This is controlled by the HCR_EL2.TGE
bit, which we forget to clear before invalidating TLBs.
Address the issue by introducing two wrappers (__tlb_switch_to_guest
and __tlb_switch_to_host) that take care of both the VTTBR_EL2
and HCR_EL2.TGE switching.
Reported-by: Tomasz Nowicki <tnowicki@caviumnetworks.com> Tested-by: Tomasz Nowicki <tnowicki@caviumnetworks.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PV_CONTROL_CLK_SELECT_VEC is actually 2 and not 0. Fix the definition and
rework the vc4_set_crtc_possible_masks() to cover the full range of the
PV_CONTROL_CLK_SELECT field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Eric Anholt <eric@anholt.net> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a small window where a userspace program could submit
a pageflip after receiving a pageflip completion event yet still
receive EBUSY.
Signed-off-by: Derek Foreman <derekf@osg.samsung.com> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Daniel Stone <daniels@collabora.com> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the build breaks if CMA=n and SPAPR_TCE_IOMMU=y:
arch/powerpc/mm/mmu_context_iommu.c: In function ‘mm_iommu_get’:
arch/powerpc/mm/mmu_context_iommu.c:193:42: error: ‘MIGRATE_CMA’ undeclared (first use in this function)
if (get_pageblock_migratetype(page) == MIGRATE_CMA) {
^~~~~~~~~~~
Fix it by using the existing is_migrate_cma_page(), which evaulates to
false when CMA=n.
Fixes: 2e5bbb5461f1 ("KVM: PPC: Book3S HV: Migrate pinned pages out of CMA") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bbe097f092b0 ("usb: gadget: udc: atmel: fix endpoint name")
introduced a memory leak when unbinding the driver. The endpoint names
would not be freed. Solve that by including the name as a string in struct
usba_ep so it is freed when the endpoint is.
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
synchronize_sched() is a heavy operation and calling it per each cache
owned by a memory cgroup being destroyed may take quite some time. What
is worse, it's currently called under the slab_mutex, stalling all works
doing cache creation/destruction.
Actually, there isn't much point in calling synchronize_sched() for each
cache - it's enough to call it just once - after setting cpu_partial for
all caches and before shrinking them. This way, we can also move it out
of the slab_mutex, which we have to hold for iterating over the slab
cache list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=172991 Link: http://lkml.kernel.org/r/0a10d71ecae3db00fb4421bcd3f82bcc911f4be4.1475329751.git.vdavydov.dev@gmail.com Signed-off-by: Vladimir Davydov <vdavydov.dev@gmail.com> Reported-by: Doug Smythies <dsmythies@telus.net> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have invalid baSourceID references, causing uvc_scan_chain()
to fail, but if we just take the entities we can find and put them
together in the most sensible chain we can think of, turns out they do
work anyway. Note: This heuristic assumes there is a single chain.
At the time of writing, devices known to have such a broken chain are
- Acer Integrated Camera (5986:055a)
- Realtek rtl157a7 (0bda:57a7)
The WRITE_SAME commands are not present in the blk_default_cmd_filter
write_ok list, and thus are failed with -EPERM when the SG_IO ioctl()
is executed without CAP_SYS_RAWIO capability (e.g., unprivileged users).
[ sg_io() -> blk_fill_sghdr_rq() > blk_verify_command() -> -EPERM ]
The problem can be reproduced with the sg_write_same command
# sg_write_same --num 1 --xferlen 512 /dev/sda
#
# capsh --drop=cap_sys_rawio -- -c \
'sg_write_same --num 1 --xferlen 512 /dev/sda'
Write same: pass through os error: Operation not permitted
#
For comparison, the WRITE_VERIFY command does not observe this problem,
since it is in that list:
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2]),
which employs the SG_IO ioctl() and runs as an unprivileged user (libvirt-qemu).
In that scenario, when a filesystem (e.g., ext4) performs its zero-out calls,
which are translated to write-same calls in the guest kernel, and then into
SG_IO ioctls to the host kernel, SCSI I/O errors may be observed in the guest:
projects / users / dwmw2 / linux.git / log