Returning to userspace is tricky: IRET can fail, and ESPFIX can
rearrange the stack prior to IRET.
The NMI nesting fixup relies on a precise stack layout and
atomic IRET. Rather than trying to teach the NMI nesting fixup
to handle ESPFIX and failed IRET, punt: run NMIs that came from
user mode on the normal kernel stack.
This will make some nested NMIs visible to C code, but the C
code is okay with that.
As a side effect, this should speed up perf: it eliminates an
RDMSR when NMIs come from user mode.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit kernels handle nested NMIs in C. Enable the exact same
handling on 64-bit kernels as well. This isn't currently
necessary, but it will become necessary once the asm code starts
allowing limited nesting.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialization firmware does some sort of
memory switch between DRAM and IRAM. If
configuration value for bank switching isn't
correct device crashes during init.
The new value prevents firmware 11.0.0.302 (and
possibly others) for qca61x4 hw2.1 from crashing
during init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
But if bitmap is disabled only the first byte of "file" is initialized
with zero, so it's possible to read some bytes (up to 4095) of kernel
space memory from user space. This is an information leak.
5775 /* bitmap disabled, zero the first byte and copy out */
5776 if (!mddev->bitmap_info.file)
5777 file->pathname[0] = '\0';
if (pm_runtime_suspended(twl->dev))
pm_runtime_get_sync(twl->dev);
is against the spirit of the runtime_pm interface as it
makes the internal refcounting useless.
In this case it is also racy, particularly as 'put_autosuspend'
is used to drop a reference.
When that happens a timer is started and the device is
runtime-suspended after the timeout.
If the above code runs in this window, the device will not be
found to be suspended so no pm_runtime reference is taken.
When the timer expires the device will be suspended, which is
against the intention of the code.
So be more direct is taking and dropping references.
If twl->linkstat is VBUS_VALID or ID_GROUND, then hold a
pm_runtime reference, otherwise don't.
Define "cable_present()" to test for this condition.
Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci_init_driver is used to initialize hcd APIs for each
ehci controller driver, it is designed to be called only one time
and before driver register is called. The current design will
cause ehci_init_driver is called multiple times at probe process,
it will cause hc_driver's initialization affect current running hcd.
We run out NULL pointer dereference problem when one hcd is started
by module_init, and the other is started by otg thread at SMP platform.
The reason for this problem is ehci_init_driver will do memory copy
for current uniform hc_driver, and this memory copy will do memset (as 0)
first, so when the first hcd is running usb_add_hcd, and the second
hcd may clear the uniform hc_driver's space (at ehci_init_driver),
then the first hcd will meet NULL pointer at the same time.
Cc: Jun Li <jun.li@freescale.com> Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in the error pathway of
usb_add_gadget_udc_release() in udc-core.c. If the udc registration
fails, the gadget registration is not fully undone; there's a
put_device(&gadget->dev) call but no device_del().
Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Sierra Wireless AR8550 device with
USB descriptor 0x1199, 0x68AB.
It is common with MC879x modules 1199:683c/683d which
also are composite devices with 7 interfaces (0..6)
and also MDM62xx based as the AR8550.
The major difference are only the interface attributes
02/02/01 on interfaces 3 and 4 on the AR8550. They are
vendor specific ff/ff/ff on MC879x modules.
lsusb reports:
Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1199 Sierra Wireless, Inc.
idProduct 0x68ab
bcdDevice 0.06
iManufacturer 3 Sierra Wireless, Incorporated
iProduct 2 AR8550
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 198
bNumInterfaces 7
bConfigurationValue 1
iConfiguration 1 Sierra Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 6
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x8a EP 10 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x8b EP 11 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x07 EP 7 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Cc: Lars Melin <larsm17@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When xhci_mem_cleanup() is called, it's possible that the command
timer isn't initialized and scheduled. For those cases, to delete
the command timer causes soft-lockup as below stack dump shows.
The patch avoids deleting the command timer if it's not scheduled
with the help of timer_pending().
We need to check that a TRB is part of the current segment
before calculating its DMA address.
Previously a ring segment didn't use a full memory page, and every
new ring segment got a new memory page, so the off by one
error in checking the upper bound was never seen.
Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one
didn't catch the case when a TRB was the first element of the next segment.
This is triggered if the virtual memory pages for a ring segment are
next to each in increasing order where the ring buffer wraps around and
causes errors like:
[ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1
[ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0
The trb-end address is one outside the end-seg address.
When pl330 driver was used during sound playback, after some time or
after a number of plays the sound became choppy or totally noisy. For
example on Odroid XU3 board the first four executions of aplay with
small WAVE worked fine, but fifth was unrecognizable with errors:
$ aplay /usr/share/sounds/alsa/Front_Right.wava
underrun!!! (at least 0.095 ms long)
Issue was caused by wrong residue reported by pl330 driver to
pcm_dmaengine for its cyclic dma transfers.
The pl330_tx_status(), residue reporting function, used a "last" flag in
a descriptor to indicate that there is no more data to send.
The pl330_tx_submit() iterated over descriptors trying to remove this
flag from them and then mark last descriptor as "last". However when
iterating it actually removed the flag not from descriptors but always
from last of it (and then reset it). Thus effectively once some
descriptor was marked as last, then it stayed like this forever causing
residue to be reported too low.
During memcpy operations the residue was always set to an u32 overflowed
value.
In pl330_tx_status() function number of currently transferred bytes was
subtracted from internal "bytes_requested" field. However this
"bytes_requested" was not initialized at start to length of memcpy
buffer so transferred bytes were subtracted from 0 causing overflow.
The l2cap_conn->smp pointer may be NULL for various valid reasons where SMP has
failed to initialize properly. One such scenario is when crypto support is
missing, another when the adapter has been powered on through a legacy method.
The smp_conn_security() function should have the appropriate check for this
situation to avoid NULL pointer dereferences.
Fixes another signed / unsigned array indexing bug in the ipr driver.
Currently, when hrrq_index wraps, it becomes a negative number. We
do the modulo, but still have a negative number, so we end up indexing
backwards in the array. Given where the hrrq array is located in memory,
we probably won't actually reference memory we don't own, but nonetheless
ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as
struct ipr_hrr_queue data, so bad things could certainly happen.
Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new
adapters. Let's take an example:
Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4:
The atomic_add_return will then return -1. We mod this with 3 and get -2, add
one and get -1 for an array index.
On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter
initialization and error interrupts so that we can optimize the other queues
for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the
I/O requests across those HRRQs.
With the default module parameter settings, this bug won't hit, only when
someone sets the ipr.number_of_msix parameter to a value larger than 3 is when
bad things start to happen.
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ipr's internal driver trace was changed to an atomic, a signed/unsigned
bug slipped in which results in us indexing backwards in our memory buffer
writing on memory that does not belong to us. This patch fixes this by removing
the modulo and instead just mask off the low bits.
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes
a crash seen as the __devices list in the scsi host was changing as we were
iterating through it.
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently been in there since forever and fairly easy to hit when
hotplugging really fast. I can do that since my mst hub has a manual
button to flick the hpd line for reprobing. The resulting WARNING spam
isn't pretty.
Cc: Dave Airlie <airlied@gmail.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Always assign audio function pointers even if the display does
not support audio. We need to properly disable the audio stream
when when using a non-audio capable monitor. Fixes purple line
on some hdmi monitors.
2. Check if a pin is in use by another encoder before disabling
it.
v2: make sure we've fetched the edid before checking audio and
look up the encoder before calling audio_detect since
connector->encoder may not be assigned yet. Separate
pin and afmt. They are allocated at different times and
have no dependency on eachother.
v3: fix connector fetching in encoder functions
v4: fix missed dig->pin check in dce6_afmt_write_latency_fields
Since we may conceivably encounter situations where the upper part of the
64bit register changes between reads, for example when a timestamp
counter overflows, change the WARN into a retry loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.
Note that this is a new attempt for the previously merged one,
reverted in
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Add note about previous (failed attempt).] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsnotify_clear_marks_by_group_flags() can race with
fsnotify_destroy_marks() so that when fsnotify_destroy_mark_locked()
drops mark_mutex, a mark from the list iterated by
fsnotify_clear_marks_by_group_flags() can be freed and thus the next
entry pointer we have cached may become stale and we dereference free
memory.
Fix the problem by first moving marks to free to a special private list
and then always free the first entry in the special list. This method
is safe even when entries from the list can disappear once we drop the
lock.
Signed-off-by: Jan Kara <jack@suse.com> Reported-by: Ashish Sangwan <a.sangwan@samsung.com> Reviewed-by: Ashish Sangwan <a.sangwan@samsung.com> Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On MIPS the GLOBAL bit of the PTE must have the same value in any
aligned pair of PTEs. These pairs of PTEs are referred to as
"buddies". In a SMP system is is possible for two CPUs to be calling
set_pte() on adjacent PTEs at the same time. There is a race between
setting the PTE and a different CPU setting the GLOBAL bit in its
buddy PTE.
This race can be observed when multiple CPUs are executing
vmap()/vfree() at the same time.
Make setting the buddy PTE's GLOBAL bit an atomic operation to close
the race condition.
The case of CONFIG_64BIT_PHYS_ADDR && CONFIG_CPU_MIPS32 is *not*
handled.
When EVA is enabled, flush the Return Prediction Stack (RPS) present on
some MIPS cores on entry to the kernel from user mode.
This is important specifically for interAptiv with EVA enabled,
otherwise kernel mode RPS mispredicts may trigger speculative fetches of
user return addresses, which may be sensitive in the kernel address
space due to EVA's overlapping user/kernel address spaces.
This reverts commit 3cf29543413207d3ab1c3f62a88c09bb46f2264e ("MIPS:
BCM63xx: Provide a plat_post_dma_flush hook") since this commit was
found to prevent BCM6358 (early BMIPS4350 cores) and some BCM6368
(BMIPS4380 cores) from booting reliably.
Alvaro was able to track this down to an issue specifically located to
devices that use the second thread (TP1) when booting. Since BCM63xx did
not have a need for plat_post_dma_flush() hook before, let's just keep
things the way they were.
The show_stack() function deals exclusively with kernel contexts, but if
it gets called in user context with EVA enabled, show_stacktrace() will
attempt to access the stack using EVA accesses, which will either read
other user mapped data, or more likely cause an exception which will be
handled by __get_user().
This is easily reproduced using SysRq t to show all task states, which
results in the following stack dump output:
Stack : (Bad stack address)
Fix by setting the current user access mode to kernel around the call to
show_stacktrace(). This causes __get_user() to use normal loads to read
the kernel stack.
If a machine check exception is raised in kernel mode, user context,
with EVA enabled, then the do_mcheck handler will attempt to read the
code around the EPC using EVA load instructions, i.e. as if the reads
were from user mode. This will either read random user data if the
process has anything mapped at the same address, or it will cause an
exception which is handled by __get_user, resulting in this output:
Code: (Bad address in epc)
Fix by setting the current user access mode to kernel if the saved
register context indicates the exception was taken in kernel mode. This
causes __get_user to use normal loads to read the kernel code.
get_c0_perfcount_int is tested from oprofile code. If oprofile is
compiled as module, get_c0_perfcount_int needs to be exported, otherwise
it cannot be resolved.
Fixes: a669efc4a3b4 ("MIPS: Add hook to get C0 performance counter interrupt") Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: linux-mips@linux-mips.org Cc: abrestic@chromium.org
Patchwork: https://patchwork.linux-mips.org/patch/10763/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Malta, since commit a87ea88d8f6c ("MIPS: Malta: initialise the RTC at
boot"), the RTC is reinitialised and forced into binary coded decimal
(BCD) mode during init, even if the bootloader has already initialised
it, and may even have already put it into binary mode (as YAMON does).
This corrupts the current time, can result in the RTC seconds being an
invalid BCD (e.g. 0x1a..0x1f) for up to 6 seconds, as well as confusing
YAMON for a while after reset, enough for it to report timeouts when
attempting to load from TFTP (it actually uses the RTC in that code).
Therefore only initialise the RTC to the extent that is necessary so
that Linux avoids interfering with the bootloader setup, while also
allowing it to estimate the CPU frequency without hanging, without a
bootloader necessarily having done anything with the RTC (for example
when the kernel is loaded via EJTAG).
The divider control is configured for a 32KHZ reference clock if
necessary, and the SET bit of the RTC_CONTROL register is cleared if
necessary without changing any other bits (this bit will be set when
coming out of reset if the battery has been disconnected).
Fixes: a87ea88d8f6c ("MIPS: Malta: initialise the RTC at boot") Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10739/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the assembler errors generated when compiling a MIPS R6 kernel with
CONFIG_KEXEC on, by replacing the offending add and sub instructions with
addiu instructions.
Commit eeb538950367 ("MIPS: unaligned: Prevent EVA instructions on kernel
unaligned accesses") renamed the Load* and Store* defines in unaligned.c
to _Load* and _Store* as part of its fix. One define was missed out which
causes big endian R6 kernels to fail to build.
arch/mips/kernel/unaligned.c:880:35:
error: implicit declaration of function '_StoreDW'
#define StoreDW(addr, value, res) _StoreDW(addr, value, res)
^
When setting yup the symbols library we setup several filter lists,
for dsos, comms, symbols, etc, and there is code that, if there are
filters, do certain operations, like recalculate the number of non
filtered histogram entries in the top/report TUI.
But they were considering just the "Zoom" filters, when they need to
take into account as well the above mentioned filters (perf top --comms,
--dsos, etc).
So store in symbol_conf.has_filter true if any of those filters is in
place.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-f5edfmhq69vfvs1kmikq1wep@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Andre Tomt <lkml@tomt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't log remote attribute contents, and instead write them
synchronously before we commit the block allocation and attribute
tree update transaction. As a result we are writing to the allocated
space before the allcoation has been made permanent.
As a result, we cannot consider this allocation to be a metadata
allocation. Metadata allocation can take blocks from the free list
and so reuse them before the transaction that freed the block is
committed to disk. This behaviour is perfectly fine for journalled
metadata changes as log recovery will ensure the free operation is
replayed before the overwrite, but for remote attribute writes this
is not the case.
Hence we have to consider the remote attribute blocks to contain
data and allocate accordingly. We do this by dropping the
XFS_BMAPI_METADATA flag from the block allocation. This means the
allocation will not use blocks that are on the busy list without
first ensuring that the freeing transaction has been committed to
disk and the blocks removed from the busy list. This ensures we will
never overwrite a freed block without first ensuring that it is
really free.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On examination of the log via xfs_logprint, none of the symlink
buffers in the log had a bad magic number, nor were any other types
of buffer log format headers mis-identified as symlink buffers.
Tracing was used to find the buffer the kernel was tripping over,
and xfs_db identified it's contents as:
This is a remote attribute buffer, which are notable in that they
are not logged but are instead written synchronously by the remote
attribute code so that they exist on disk before the attribute
transactions are committed to the journal.
The above remote attribute block has an invalid LSN in it - cycle
0xd002000, block 0 - which means when log recovery comes along to
determine if the transaction that writes to the underlying block
should be replayed, it sees a block that has a future LSN and so
does not replay the buffer data in the transaction. Instead, it
validates the buffer magic number and attaches the buffer verifier
to it. It is this buffer magic number check that is failing in the
above assert, indicating that we skipped replay due to the LSN of
the underlying buffer.
The problem here is that the remote attribute buffers cannot have a
valid LSN placed into them, because the transaction that contains
the attribute tree pointer changes and the block allocation that the
attribute data is being written to hasn't yet been committed. Hence
the LSN field in the attribute block is completely unwritten,
thereby leaving the underlying contents of the block in the LSN
field. It could have any value, and hence a future overwrite of the
block by log recovery may or may not work correctly.
Fix this by always writing an invalid LSN to the remote attribute
block, as any buffer in log recovery that needs to write over the
remote attribute should occur. We are protected from having old data
written over the attribute by the fact that freeing the block before
the remote attribute is written will result in the buffer being
marked stale in the log and so all changes prior to the buffer stale
transaction will be cancelled by log recovery.
Hence it is safe to ignore the LSN in the case or synchronously
written, unlogged metadata such as remote attribute blocks, and to
ensure we do that correctly, we need to write an invalid LSN to all
remote attribute blocks to trigger immediate recovery of metadata
that is written over the top.
As a further protection for filesystems that may already have remote
attribute blocks with bad LSNs on disk, change the log recovery code
to always trigger immediate recovery of metadata over remote
attribute blocks.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RING_SPACE macro accounts how much space is used up so it's
important to ask it for the right amount. Incorrect accounting of this
can cause page faults down the line as writes are attempted outside of
the ring.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix some issues talking to ESX, this patch modifies the qla2xxx driver
so that it never logs into remote ports. This has the side effect of
getting rid of the "rports" entirely, which means we never log out of
initiators and never tear down sessions when an initiator goes away.
This is mostly OK, except that we can run into trouble if we have
initiator A assigned FC address X:Y:Z by the fabric talking to us, and
then initiator A goes away. Some time (could be a long time) later,
initiator B comes along and also gets FC address X:Y:Z (which is
available again, because initiator A is gone). If initiator B starts
talking to us, then we'll still have the session for initiator A, and
since we look up incoming IO based on the FC address X:Y:Z, initiator B
will end up using ACLs for initiator A.
Fix this by:
1. Handling RSCN events somewhat differently; instead of completely
skipping the processing of fcports, we look through the list, and if
an fcport disappears, we tell the target code the tear down the
session and tell the HBA FW to release the N_Port handle.
2. Handling "port down" events by flushing all of our sessions. The
firmware was already releasing the N_Port handle but we want the
target code to drop all the sessions too.
Request IOCB queue element(s) is reserved during
good path IO. Under error condition such as unable
to allocate IOCB handle condition, the IOCB count
that was reserved is not released.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scaling for Knights Landing is same as the default scaling (100000).
When Knigts Landing support was added to the pstate driver, this
parameter was omitted resulting in a kernel panic during boot.
This patch fixes a regression introduced with the following commit
in v4.0-rc1 code, where an explicit iser-target logout would result
in ->tx_thread_active being incorrectly cleared by the logout post
handler, and subsequent TX kthread leak:
iscsi-target: Convert iscsi_thread_set usage to kthread.h
To address this bug, change iscsit_logout_post_handler_closesession()
and iscsit_logout_post_handler_samecid() to only cmpxchg() on
->tx_thread_active for traditional iscsi/tcp connections.
This is required because iscsi/tcp connections are invoking logout
post handler logic directly from TX kthread context, while iser
connections are invoking logout post handler logic from a seperate
workqueue context.
This patch fixes a regression introduced with the following commit
in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers
a NULL pointer dereference OOPs:
iscsi-target: Convert iscsi_thread_set usage to kthread.h
To address this bug, move iscsit_start_kthreads() immediately
preceeding the transmit of last login response, before signaling
a successful transition into full-feature-phase within existing
iscsi_target_do_tx_login_io() logic.
This ensures that no target-side resource allocation failures can
occur after the final login response has been successfully sent.
Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread
to sleep to prevent other socket related failures until the final
iscsi_post_login_handler() call is able to complete.
This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg()
where se_portal_group->session_lock was incorrectly released/re-acquired
while walking the active se_portal_group->tpg_sess_list.
The can result in a NULL pointer dereference when iscsit_close_session()
shutdown happens in the normal path asynchronously to this code, causing
a bogus dereference of an already freed list entry to occur.
To address this bug, walk the session list checking for the same state
as before, but move entries to a local list to avoid dropping the lock
while walking the active list.
As before, signal using iscsi_session->session_restatement=1 for those
list entries to be released locally by iscsit_free_session() code.
If the above is turned off then ipoib_cm_dev_init unconditionally
returns ENOSYS, and the newly added error handling in
0b3957 prevents ipoib from coming up at all:
kernel: mlx4_0: ipoib_transport_dev_init failed
kernel: mlx4_0: failed to initialize port 1 (ret = -12)
Fixes: 0b39578bcde4 (IB/ipoib: Use dedicated workqueues per interface) Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function exits early, then we must put those requests that were
not processed back onto the &mirror->pg_list so they can be cleaned up
by nfs_pgio_error().
Fixes: a7d42ddb30997 ("nfs: add mirroring support to pgio layer") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we've ensured that the size and the change attribute are both correct,
then there is no point in marking those attributes as needing revalidation
again. Only do so if we know the size is incorrect and was not updated.
The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".
Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vikas Shivappa <vikas.shivappa@intel.com> Cc: Kanaka Juvva <kanaka.d.juvva@intel.com> Cc: Will Auld <will.auld@intel.com> Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c86c7ca7606
Author: Namhyung Kim <namhyung@kernel.org>
Date: Mon Mar 17 18:18:54 2014 -0300
perf report: Merge al->filtered with hist_entry->filtered
We stopped dropping samples for things filtered via the --comms, --dsos,
--symbols, etc, i.e. things marked as filtered in the symbol resolution
routines (thread__find_addr_map(), perf_event__preprocess_sample(),
etc).
perf top/tui: Update nr_entries properly after a filter is applied
We don't take into account entries that were filtered in
perf_event__preprocess_sample() and friends, which leads to
inconsistency in the browser seek routines, that expects the number of
hist_entry->filtered entries to match what it thinks is the number of
unfiltered, browsable entries.
So, for instance, when we do:
perf top --symbols ___non_existent_symbol___
the hist_browser__nr_entries() routine thinks there are no filters in
place, uses the hists->nr_entries but all entries are filtered, leading
to a segfault.
Tested with:
perf top --symbols malloc,free --percentage=relative
Freezing, by pressing 'f', at any time and doing the math on the
percentages ends up with 100%, ditto for:
perf top --dsos libpthread-2.20.so,libxul.so --percentage=relative
Both were segfaulting, all fixed now.
More work needed to do away with checking if filters are in place, we
should just use the nr_non_filtered_samples counter, no need to
conditionally use it or hists.nr_filter, as what the browser does is
just show unfiltered stuff. An audit of how it is being accounted is
needed, this is the minimal fix.
Reported-by: Michael Petlan <mpetlan@redhat.com> Fixes: 268397cb2a47 ("perf top/tui: Update nr_entries properly after a filter is applied") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-6w01d5q97qk0d64kuojme5in@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reasonable to set default timeout of request as 30 seconds instead of
30000 ticks, which may be 300 seconds if HZ is 100, for example, some arm64
based systems may choose 100 HZ.
Signed-off-by: Ming Lei <ming.lei@canonical.com> Fixes: c76cbbcf4044 ("blk-mq: put blk_queue_rq_timeout together in blk_mq_init_queue()" Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...") Fixes: commit d2b6f44779d3 ("n_tty: Fix signal handling flushes") Reported-by: Filipe Brandenburger <filbranden@google.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 3e0249f9c05c ("RDS/IB: add refcount tracking to struct rds_ib_device")
There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr
failed(mr pool running out). this lead to the refcount overflow.
A complain in line 117(see following) is seen. From vmcore:
s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448.
That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely
to return ERR_PTR(-EAGAIN).
ARCompact/ARCv2 ISA provide that any instructions which deals with
bitpos/count operand ASL, LSL, BSET, BCLR, BMSK .... will only consider
lower 5 bits. i.e. auto-clamp the pos to 0-31.
ARC Linux bitops exploited this fact by NOT explicitly masking out upper
bits for @nr operand in general, saving a bunch of AND/BMSK instructions
in generated code around bitops.
While this micro-optimization has worked well over years it is NOT safe
as shifting a number with a value, greater than native size is
"undefined" per "C" spec.
So as it turns outm EZChip ran into this eventually, in their massive
muti-core SMP build with 64 cpus. There was a test_bit() inside a loop
from 63 to 0 and gcc was weirdly optimizing away the first iteration
(so it was really adhering to standard by implementing undefined behaviour
vs. removing all the iterations which were phony i.e. (1 << [63..32])
| for i = 63 to 0
| X = ( 1 << i )
| if X == 0
| continue
So fix the code to do the explicit masking at the expense of generating
additional instructions. Fortunately, this can be mitigated to a large
extent as gcc has SHIFT_COUNT_TRUNCATED which allows combiner to fold
masking into shift operation itself. It is currently not enabled in ARC
gcc backend, but could be done after a bit of testing.
Fixes STAR 9000866918 ("unsafe "undefined behavior" code in kernel")
Even though it is documented how to specifiy efi parameters, it is
possible to cause a kernel panic due to a dereference of a NULL pointer when
parsing such parameters if "efi" alone is given:
This panic is not reproducible with "efi=" as this will result in a non-NULL
zero-length string.
Thus, verify that the pointer to the parameter string is not NULL. This is
consistent with other parameter-parsing functions which check for NULL pointers.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At boot, the UTF-16 UEFI vendor string is copied from the system
table into a char array with a size of 100 bytes. However, this
size of 100 bytes is also used for memremapping() the source,
which may not be sufficient if the vendor string exceeds 50
UTF-16 characters, and the placement of the vendor string inside
a 4 KB page happens to leave the end unmapped.
So use the correct '100 * sizeof(efi_char16_t)' for the size of
the mapping.
The memory error record structure includes as its first field a
bitmask of which subsequent fields are valid. The allows new fields
to be added to the structure while keeping compatibility with older
software that parses these records. This mechanism was used between
versions 2.2 and 2.3 to add four new fields, growing the size of the
structure from 73 bytes to 80. But Linux just added all the new
fields so this test:
if (gdata->error_data_length >= sizeof(*mem_err))
cper_print_mem(newpfx, mem_err);
else
goto err_section_too_small;
now make Linux complain about old format records being too short.
Add a definition for the old format of the structure and use that
for the minimum size check. Pass the actual size to cper_print_mem()
so it can sanity check the validation_bits field to ensure that if
a BIOS using the old format sets bits as if it were new, we won't
access fields beyond the end of the structure.
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_tlb_info->flush_start/end are both normal virtual
addresses. When calculating 'nr_pages' (only used for the
tracepoint), I neglected to put parenthesis in.
Thanks to David Koufaty for pointing this out.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dave@sr71.net Link: http://lkml.kernel.org/r/20150720230153.9E834081@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chrdev_open() increases reference counter on cdev->owner. Instead of
assigning the owner to mei subsystem, the owner has to be set to the
underlaying HW module (mei_me or mei_txe), so once the device is opened
the HW module cannot be unloaded.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port link change with port in resume state should not be
reported to usbcore, as this is an internal state to be
handled by xhci driver. Reporting PLC to usbcore may
cause usbcore clearing PLC first and port change event irq
won't be generated.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the link is just waken, it's in Resume state, and driver sets PLS to
U0. This refers to Phase 1. Phase 2 refers to when the link has completed
the transition from Resume state to U0.
With the fix of xhci: report U3 when link is in resume state, it also
exposes an issue that usb3 roothub and controller can suspend right
after phase 1, and this causes a hard hang in controller.
To fix the issue, we need to prevent usb3 bus suspend if any port is
resuming in phase 1.
[merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_hub_report_usb3_link_state() returns pls as U0 when the link
is in resume state, and this causes usb core to think the link is in
U0 while actually it's in resume state. When usb core transfers
control request on the link, it fails with TRB error as the link
is not ready for transfer.
To fix the issue, report U3 when the link is in resume state, thus
usb core knows the link it's not ready for transfer.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.
This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking. For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.
The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e758910832d ("serial: core: Flush ldisc after dropping port
mutex in uart_close()") Reported-by: Robert Elliott <elliott@hp.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device automatically switches itself to another mode (0x1405)
unless the specific access pattern of Windows is followed in its
initial mode. That makes a dirty unmount of the internal storage
devices inevitable if they are mounted. So the card reader of
such a device should be ignored, lest an unclean removal become
inevitable.
This replaces an earlier patch that ignored all LUNs of this device.
That patch was overly broad.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Status of enabling suspend mode for regulator was stored in bitmap-like
long integer.
However since adding support for S2MPU02 the number of regulators
exceeded 32 so on devices with more than 32 regulators (S2MPU02 and
S2MPS13) overflow happens when shifting the bit. This could lead to
enabling suspend mode for completely different regulator than intended
or to switching different regulator to other mode (e.g. from always
enabled to controlled by PWRHOLD pin). Both cases could result in larger
energy usage and issues when suspending to RAM.
Fixes: 00e2573d2c10 ("regulator: s2mps11: Add support S2MPU02 regulator device") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a blkcg configuration is targeted to a partition rather than a
whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it
forgets to put the gendisk ref in that case. Fix it.
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the Same Edge bit indicates to the spfi block to receive and
transmit data on the same edge of the spfi clock, which in turn
doubles the operating frequency of spfi.
The maximum supported frequency is limited to 1/4th of the spfi input
clock, but without this bit set the maximum would be 1/8th of the
input clock.
The current driver calculates the divisor with maximum speed at 1/4th
of the input clock, this would fail if the requested frequency is
higher than 1/8 of the input clock. Any requests for 1/8th of the
input clock would still pass.
Fixes: 8543d0e72d43 ("spi: img-spfi: Limit bit clock to 1/4th of input clock") Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054c95b ("md/raid1: clean up read_balance.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For 8000 series, we need to access the device to know what
firmware to load. Before we do so, we need to prepare the
device otherwise we might not be able to access the
hardware.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.
When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181
Current implementation of cp2112_raw_event() only accepts one data report at a
time. If last received data report is not fully handled yet, a new incoming
data report will overwrite it. In such case we don't guaranteed to propagate
the correct incoming data.
The trivial fix implemented here forces a single report at a time by requesting
in cp2112_read() no more than 61 byte of data, which is the payload size of a
single data report.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
This continues the attempt to fix commit fb170fb4c548 ("iommu/vt-d:
Introduce helper functions to make code symmetric for readability").
The previous attempt in commit 71684406905f ("iommu/vt-d: Detach
domain *only* from attached iommus") overlooked the fact that
dmar_domain.iommu_bmp gets cleared for VM domains when devices are
detached:
The domain is detached from the iommu, but the iommu is still attached
to the domain, for whatever reason. Thus when we get to domain_exit(),
we can't rely on iommu_bmp for VM domains to find the active iommus,
we must check them all. Without that, the corresponding bit in
intel_iommu.domain_ids doesn't get cleared and repeated VM domain
creation and destruction will run out of domain IDs. Meanwhile we
still can't call iommu_detach_domain() on arbitrary non-VM domains or
we risk clearing in-use domain IDs, as 71684406905f attempted to
address.
It's tempting to modify iommu_detach_domain() to test the domain
iommu_bmp, but the call ordering from domain_remove_one_dev_info()
prevents it being able to work as fb170fb4c548 seems to have intended.
Caching of unused VM domains on the iommu object seems to be the root
of the problem, but this code is far too fragile for that kind of
rework to be proposed for stable, so we simply revert this chunk to
its state prior to fb170fb4c548.
Fixes: fb170fb4c548 ("iommu/vt-d: Introduce helper functions to make
code symmetric for readability") Fixes: 71684406905f ("iommu/vt-d: Detach domain *only* from attached
iommus") Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4104d326b670 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.
Add back the proper hooks to have pid filtering working once again.
Reported-by: Matt Fleming <matt@console-pimps.org> Reported-by: Richard Weinberger <richard.weinberger@gmail.com> Tested-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handling of in detach_mounts of unmounted but connected mounts is
buggy and can lead to an infinite loop.
Correct the handling of unmounted mounts in detach_mount. When the
mountpoint of an unmounted but connected mount is connected to a
dentry, and that dentry is deleted we need to disconnect that mount
from the parent mount and the deleted dentry.
Nothing changes for the unmounted and connected children. They can be
safely ignored.
Fixes: ce07d891a0891d3c0d0c2d73d577490486b809e1 mnt: Honor MNT_LOCKED when detaching mounts Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rmdir mntpoint will result in an infinite loop when there is
a mount locked on the mountpoint in another mount namespace.
This is because the logic to test to see if a mount should
be disconnected in umount_tree is buggy.
Move the logic to decide if a mount should remain connected to
it's mountpoint into it's own function disconnect_mount so that
clarity of expression instead of terseness of expression becomes
a virtue.
When the conditions where it is invalid to leave a mount connected
are first ruled out, the logic for deciding if a mount should
be disconnected becomes much clearer and simpler.
Fixes: e0c9c0afd2fc958ffa34b697972721d81df8a56f mnt: Update detach_mounts to leave mounts connected Fixes: ce07d891a0891d3c0d0c2d73d577490486b809e1 mnt: Honor MNT_LOCKED when detaching mounts Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log