Commit c685af1108d7 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
In stm_heartbeat_init(): return value gets reset after the first
iteration by stm_source_register_device(), so allocation failures
after that will, after a clean up, return success. Fix that.
Fixes: 119291853038 ("stm class: Add heartbeat stm source device") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hui <john.wanghui@huawei.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: https://lore.kernel.org/r/20210115195917.3184-2-alexander.shishkin@linux.intel.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 55567976629e ("genirq/irqdomain: Allow partial trimming of
irq_data hierarchy") the irq_data chain is valided.
The irq_domain_trim_hierarchy() function doesn't consider the irq + ipi
domain hierarchy as valid, since the ipi domain has the irq domain set
as parent, but the parent domain has no chip set. Hence the boot ends in
a kernel panic.
Set the chip for the parent domain as it is done in the mips gic irq
driver, to have a valid irq_data chain.
The power-down mask of the ad5504 is actually a power-up mask. Meaning if
a bit is set the corresponding channel is powered up and if it is not set
the channel is powered down.
The driver currently has this the wrong way around, resulting in the
channel being powered up when requested to be powered down and vice versa.
Fixes: 3bbbf150ffde ("staging:iio:dac:ad5504: Use strtobool for boolean values") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20201209104649.5794-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After calling peak_usb_netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the peak_usb_netif_rx_ni().
Reordering the lines solves the issue.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/r/20210120114137.200019-4-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the canfd_frame cfd which aliases skb memory is accessed
after the netif_rx_ni().
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/r/20210120114137.200019-3-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the netif_rx_ni() in:
stats->rx_bytes += cf->len;
Reordering the lines solves the issue.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface") Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous test added an address with a specified metric and check if
correspond route was created. I somehow added two logs for the same
test. Remove the duplicated one.
Reported-by: Antoine Tenart <atenart@redhat.com> Fixes: 0d29169a708b ("selftests/net/fib_tests: update addr_metric_test for peer route testing") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20210119025930.2810532-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
THe HP Stream x360 Convertible PC 11 DSDT has the following VGBS function:
Method (VGBS, 0, Serialized)
{
If ((^^PCI0.LPCB.EC0.ROLS == Zero))
{
VBDS = Zero
}
Else
{
VBDS = Zero
}
Return (VBDS) /* \_SB_.VGBI.VBDS */
}
Which is obviously wrong, because it always returns 0 independent of the
2-in-1 being in laptop or tablet mode. This causes the intel-vbtn driver
to initially report SW_TABLET_MODE = 1 to userspace, which is known to
cause problems when the 2-in-1 is actually in laptop mode.
During earlier testing this turned out to not be a problem because the
2-in-1 would do a Notify(..., 0xCC) or Notify(..., 0xCD) soon after
the intel-vbtn driver loaded, correcting the SW_TABLET_MODE state.
Further testing however has shown that this Notify() soon after the
intel-vbtn driver loads, does not always happen. When the Notify
does not happen, then intel-vbtn reports SW_TABLET_MODE = 1 resulting in
a non-working touchpad.
IOW the tablet-mode reporting is not reliable on this device, so it
should be dropped from the allow-list, fixing the touchpad sometimes
not working.
Fixes: 8169bd3e6e19 ("platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting") Link: https://lore.kernel.org/r/20210114143432.31750-1-hdegoede@redhat.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Phil Oester reported that a fix for a possible buffer overrun that I sent
caused a regression that manifests in this output:
Event Message: A PCI parity error was detected on a component at bus 0 device 5 function 0.
Severity: Critical
Message ID: PCI1308
The original code tried to handle the sense data pointer differently when
using 32-bit 64-bit DMA addressing, which would lead to a 32-bit dma_addr_t
value of 0x11223344 to get stored
In my patch, I tried to ensure that the same value is used on both 32-bit
and 64-bit kernels, and picked what seemed to be the most sensible
combination, storing 32-bit addresses in the first four bytes (as 32-bit
kernels already did), and 64-bit addresses in eight consecutive bytes (as
64-bit kernels already did), but evidently this was incorrect.
Always storing the dma_addr_t pointer as 64-bit little-endian,
i.e. initializing the second four bytes to zero in case of 32-bit
addressing, apparently solved the problem for Phil, and is consistent with
what all 64-bit little-endian machines did before.
I also checked in the history that in previous versions of the code, the
pointer was always in the first four bytes without padding, and that
previous attempts to fix 64-bit user space, big-endian architectures and
64-bit DMA were clearly flawed and seem to have introduced made this worse.
Link: https://lore.kernel.org/r/20210104234137.438275-1-arnd@kernel.org Fixes: 381d34e376e3 ("scsi: megaraid_sas: Check user-provided offsets") Fixes: 107a60dd71b5 ("scsi: megaraid_sas: Add support for 64bit consistent DMA") Fixes: 94cd65ddf4d7 ("[SCSI] megaraid_sas: addded support for big endian architecture") Fixes: 7b2519afa1ab ("[SCSI] megaraid_sas: fix 64 bit sense pointer truncation") Reported-by: Phil Oester <kernel@linuxace.com> Tested-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue has generally been covered up by the presence of additional
expansion ROMs after the ones we're interested in, with header fetches
of subsequent images loading enough of the ROM to hide the issue.
Noticed on GA102, which lacks a type 0x70 image compared to TU102,.
[ 906.364197] nouveau 0000:09:00.0: bios: 00000000: type 00, 65024 bytes
[ 906.381205] nouveau 0000:09:00.0: bios: 0000fe00: type 03, 91648 bytes
[ 906.405213] nouveau 0000:09:00.0: bios: 00026400: type e0, 22016 bytes
[ 906.410984] nouveau 0000:09:00.0: bios: 0002ba00: type e0, 366080 bytes
vs
[ 22.961901] nouveau 0000:09:00.0: bios: 00000000: type 00, 60416 bytes
[ 22.984174] nouveau 0000:09:00.0: bios: 0000ec00: type 03, 71168 bytes
[ 23.010446] nouveau 0000:09:00.0: bios: 00020200: type e0, 48128 bytes
[ 23.028220] nouveau 0000:09:00.0: bios: 0002be00: type e0, 140800 bytes
[ 23.080196] nouveau 0000:09:00.0: bios: 0004e400: type 70, 7168 bytes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current implementation defaults the hda clocks to clk_m. This causes hda
to run too slow to operate correctly. Fix this by defaulting to pll_p and
setting the frequency to the correct rate.
This matches upstream t124 and downstream t30.
Acked-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Ion Agorria <ion@agorria.com> Acked-by: Sameer Pujar <spujar@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Link: https://lore.kernel.org/r/20210108135913.2421585-2-pgwipeout@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If of_clk_init() is not called in time_init(), clock providers defined
in the system device tree are not initialized, resulting in failures for
other devices to initialize due to missing clocks.
Similarly to other architectures and to the default kernel time_init()
implementation, call of_clk_init() before executing timer_probe() in
time_init().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.
Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.org Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
haswell machine board is missing pm_ops what prevents it from undergoing
suspend-resume procedure successfully. Assign default snd_soc_pm_ops so
this is no longer the case.
This reverts commit 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()")
dm_get_dev_t() is just used to convert an arbitrary 'path' string
into a dev_t. It doesn't presume that the device is present; that
check will be done later, as the only caller is dm_get_device(),
which does a dm_get_table_device() later on, which will properly
open the device.
So if the path string already _is_ in major:minor representation
we can convert it directly, avoiding a recursion into the filesystem
to lookup the block device.
This avoids a hang in multipath_message() when the filesystem is
inaccessible.
Fixes: 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()") Cc: stable@vger.kernel.org Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
If extended CSD was not available, the eMMC driver would incorrectly
set the block size to 0, as the data_sector_size field of ext_csd
was never initialized. This issue was exposed by commit 817046ecddbc
("block: Align max_hw_sectors to logical blocksize") which caused
max_sectors and max_hw_sectors to be set to 0 after setting the block
size to 0, resulting in a kernel panic in bio_split when attempting
to read from the device. Fix it by only reading the block size from
ext_csd if it is available.
Set the acpi_device pointer which acpi_bus_get_device() returns-by-
reference to NULL on errors.
We've recently had 2 cases where callers of acpi_bus_get_device()
did not properly error check the return value, so set the returned-
by-reference acpi_device pointer to NULL, because at least some
callers of acpi_bus_get_device() expect that to be done on errors.
[ rjw: This issue was exposed by commit 71da201f38df ("ACPI: scan:
Defer enumeration of devices with _DEP lists") which caused it to
be much more likely to occur on some systems, but the real defect
had been introduced by an earlier commit. ]
Fixes: 40e7fcb19293 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA") Fixes: bcfcd409d4db ("usb: split code locating ACPI companion into port and device") Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Diagnosed-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: All applicable <stable@vger.kernel.org>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turned out that VIA codecs also mute the sound in the lowest mixer
level. Turn on the dac_min_mute flag to indicate the mute-as-minimum
in TLV like already done in Conexant and IDT codecs.
snd_seq_oss_synth_make_info() didn't check the error code from
snd_seq_oss_midi_make_info(), and this leads to the call of strlcpy()
with the uninitialized string as the source, which may lead to the
access over the limit.
Add the proper error check for avoiding the failure.
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054a4 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This worked before, because we made all callers name their next pointer
"next". But in trying to be more "drop-in" ready, the silliness here is
revealed. This commit fixes the problem by making the macro argument and
the member use different names.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the continual effort to remove direct usage of skb->next and
skb->prev, this patch adds a helper for iterating through the
singly-linked variant of skb lists, which are used for lists of GSO
packet. The name "skb_list_..." has been chosen to match the existing
function, "kfree_skb_list, which also operates on these singly-linked
lists, and the "..._walk_safe" part is the same idiom as elsewhere in
the kernel.
This patch removes the helper from wireguard and puts it into
linux/skbuff.h, while making it a bit more robust for general usage. In
particular, parenthesis are added around the macro argument usage, and it
now accounts for trying to iterate through an already-null skb pointer,
which will simply run the iteration zero times. This latter enhancement
means it can be used to replace both do { ... } while and while (...)
open-coded idioms.
This should take care of these three possible usages, which match all
current methods of iterations.
Gcc appears to generate efficient code for each of these.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ Just the skbuff.h changes for backporting - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer list can have zero skb as following path:
tipc_named_node_up()->tipc_node_xmit()->tipc_link_xmit(), so
we need to check the list before casting an &sk_buff.
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca7d ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()") Reported-by: Tom Rix <trix@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd363 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Greg Thelen <gthelen@google.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit c269a24ce057 ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com Fixes: e2f1f072db8d ("sit: allow to configure 6rd tunnels via netlink") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the original mtu is not used when the mtu is updated,
the mtu is aligned with cache, this will get an incorrect.
For example, if you want to configure the mtu to be 1500,
but mtu 1536 is configured in fact.
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
As it happens, we used READ_ONCE() to read the state a few lines above the
unmarked read in rxrpc_input_data(), so use that value rather than
re-reading it.
In commit 826f328e2b7e ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver") Fixes: 826f328e2b7e ("net: dcb: Validate netlink message in DCB handler") Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1baa ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()") Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packet Processor hardware not connected to MAC flow control unit and
cannot support TX flow control.
This patch disable flow control support.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Stefan Chulski <stefanc@marvell.com> Acked-by: Marcin Wojtas <mw@semihalf.com> Link: https://lore.kernel.org/r/1610306582-16641-1-git-send-email-stefanc@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all PCI functions on the netxen_nic adapter, interrupt
mode (INTx or MSI) configuration is dependent on what has
been configured by the PCI function zero in the shared
interrupt register, as these adapters do not support mixed
mode interrupts among the functions of a given adapter.
Logic for setting MSI/MSI-x interrupt mode in the shared interrupt
register based on PCI function id zero check is not appropriate for
all family of netxen adapters, as for some of the netxen family
adapters PCI function zero is not really meant to be probed/loaded
in the host but rather just act as a management function on the device,
which caused all the other PCI functions on the adapter to always use
legacy interrupt (INTx) mode instead of choosing MSI/MSI-x interrupt mode.
This patch replaces that check with port number so that for all
type of adapters driver attempts for MSI/MSI-x interrupt modes.
reuse->socks[] is modified concurrently by reuseport_add_sock. To
prevent reading values that have not been fully initialized, only read
the array up until the last known safe index instead of incorrectly
re-reading the last index of the array.
Fixes: acdcecc61285f ("udp: correct reuseport selection with connected sockets") Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20210107051110.12247-1-baptiste.lepers@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you export a subdirectory of a filesystem, a READDIRPLUS on the root
of that export will return the filehandle of the parent with the ".."
entry.
The filehandle is optional, so let's just not return the filehandle for
".." if we're at the root of an export.
Note that once the client learns one filehandle outside of the export,
they can trivially access the rest of the export using further lookups.
However, it is also not very difficult to guess filehandles outside of
the export. So exporting a subdirectory of a filesystem should
considered equivalent to providing access to the entire filesystem. To
avoid confusion, we recommend only exporting entire filesystems.
Reported-by: Youjipeng <wangzhibei1999@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With external metadata device, flush requests are not passed down to the
data device.
Fix this by submitting the flush request in dm_integrity_flush_buffers. In
order to not degrade performance, we overlap the data device flush with
the metadata device flush.
GCC versions >= 4.9 and < 5.1 have been shown to emit memory references
beyond the stack pointer, resulting in memory corruption if an interrupt
is taken after the stack pointer has been adjusted but before the
reference has been executed. This leads to subtle, infrequent data
corruption such as the EXT4 problems reported by Russell King at the
link below.
Life is too short for buggy compilers, so raise the minimum GCC version
required by arm64 to 5.1.
Reported-by: Russell King <linux@armlinux.org.uk> Suggested-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@vger.kernel.org> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Florian Weimer <fweimer@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20210105154726.GD1551@shell.armlinux.org.uk Link: https://lore.kernel.org/r/20210112224832.10980-1-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[will: backport to 4.19.y/5.4.y] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'distrust_firmware' module parameter dates from 2004 and the USB
subsystem is a lot more mature and reliable now than it was then.
Alter the default to false now.
The old way of changing the conntrack hashsize runtime was through changing
the module param via file /sys/module/nf_conntrack/parameters/hashsize. This
was extended to sysctl change in commit 3183ab8997a4 ("netfilter: conntrack:
allow increasing bucket size via sysctl too").
The commit introduced second "user" variable nf_conntrack_htable_size_user
which shadow actual variable nf_conntrack_htable_size. When hashsize is
changed via module param this "user" variable isn't updated. This results in
sysctl net/netfilter/nf_conntrack_buckets shows the wrong value when users
update via the old way.
This patch fix the issue by always updating "user" variable when reading the
proc file. This will take care of changes to the actual variable without
sysctl need to be aware.
There wasn't ever a real need to log an error in the kernel log for
ioctls issued with insufficient permissions. Simply return an error
and if an admin/user is sufficiently motivated they can enable DM's
dynamic debugging to see an explanation for why the ioctls were
disallowed.
Reported-by: Nir Soffer <nsoffer@redhat.com> Fixes: e980f62353c6 ("dm: don't allow ioctls to targets that don't map to whole devices") Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acquire_slab() fails if there is contention on the freelist of the page
(probably because some other CPU is concurrently freeing an object from
the page). In that case, it might make sense to look for a different page
(since there might be more remote frees to the page from other CPUs, and
we don't want contention on struct page).
However, the current code accidentally stops looking at the partial list
completely in that case. Especially on kernels without CONFIG_NUMA set,
this means that get_partial() fails and new_slab_objects() falls back to
new_slab(), allocating new pages. This could lead to an unnecessary
increase in memory fragmentation.
Link: https://lkml.kernel.org/r/20201228130853.1871516-1-jannh@google.com Fixes: 7ced37197196 ("slub: Acquire_slab() avoid loop") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the allocation of the fast path blue flame register fails, the driver
should free the regular blue flame register allocated a statement above,
not the one that it just failed to allocate.
Fixes: 16c1975f1032 ("IB/mlx5: Create profile infrastructure to add and remove stages") Link: https://lore.kernel.org/r/20210113121703.559778-6-leon@kernel.org Reported-by: Hans Petter Selasky <hanss@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting password salt in the superblock, we forget to recompute the
superblock checksum so it will not match until the next superblock
modification which recomputes the checksum. Fix it.
CC: Michael Halcrow <mhalcrow@google.com> Reported-by: Andreas Dilger <adilger@dilger.ca> Fixes: 9bd8212f981e ("ext4 crypto: add encryption policy and password salt support") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20201216101844.22917-8-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before referencing the inode, we must ensure that the superblock can be
referenced. Otherwise, we can end up with iput() calling superblock
operations that are no longer valid or accessible.
Fixes: ea7c38fef0b7 ("NFSv4: Ensure we reference the inode for return-on-close in delegreturn") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we exit _lgopen_prepare_attached() without setting a layout, we will
currently leak the plh_outstanding counter.
Fixes: 411ae722d10a ("pNFS: Wait for stale layoutget calls to complete in pnfs_update_layout()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the axg-tdm-interface was introduced, the backend DAI was marked as an
endpoint when DPCM was walking the DAPM graph to find a its BE.
It is no longer the case since this
commit 8dd26dff00c0 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks")
Because of this, when DPCM finds a BE it does everything it needs on the
DAIs but it won't power up the widgets between the FE and the BE if there
is no actual endpoint after the BE.
On meson-axg HWs, the loopback is a special DAI of the tdm-interface BE.
It is only linked to the dummy codec since there no actual HW after it.
>From the DAPM perspective, the DAI has no endpoint. Because of this, the TDM
decoder, which is a widget between the FE and BE is not powered up.
>From the user perspective, everything seems fine but no data is produced.
Connecting the Loopback DAI to a dummy DAPM endpoint solves the problem.
Fixes: 8dd26dff00c0 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks") Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20201217150812.3247405-1-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are not guaranteed the locking environment that would prevent
dentry getting renamed right under us. And it's possible for
old long name to be freed after rename, leading to UAF here.
Commit 6cc7c266e5b4 ("ima: Call ima_calc_boot_aggregate() in
ima_eventdigest_init()") added a call to ima_calc_boot_aggregate() so that
the digest can be recalculated for the boot_aggregate measurement entry if
the 'd' template field has been requested. For the 'd' field, only SHA1 and
MD5 digests are accepted.
Given that ima_eventdigest_init() does not have the __init annotation, all
functions called should not have it. This patch removes __init from
ima_pcrread().
Since commit 1d6cd3929360 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
fs/dax.c uses copy_user_page() but ARC does not provide that interface,
resulting in a build error.
Provide copy_user_page() in <asm/page.h>.
../fs/dax.c: In function 'copy_cow_page_dax':
../fs/dax.c:702:2: error: implicit declaration of function 'copy_user_page'; did you mean 'copy_to_user_page'? [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: linux-snps-arc@lists.infradead.org Cc: Dan Williams <dan.j.williams@intel.com>
#Acked-by: Vineet Gupta <vgupta@synopsys.com> # v1 Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Jan Kara <jack@suse.cz> Cc: linux-fsdevel@vger.kernel.org Cc: linux-nvdimm@lists.01.org
#Reviewed-by: Ira Weiny <ira.weiny@intel.com> # v2 Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BFQ computes number of tags it allows to be allocated for each request type
based on tag bitmap. However it uses 1 << bitmap.shift as number of
available tags which is wrong. 'shift' is just an internal bitmap value
containing logarithm of how many bits bitmap uses in each bitmap word.
Thus number of tags allowed for some request types can be far to low.
Use proper bitmap.depth which has the number of tags instead.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
If we remount a filesystem in RO mode while the qgroup rescan worker is
running, we can end up having it still running after the remount is done,
and at unmount time we may end up with an open transaction that ends up
never getting committed. If that happens we end up with several memory
leaks and can crash when hardware acceleration is unavailable for crc32c.
Possibly it can lead to other nasty surprises too, due to use-after-free
issues.
The following steps explain how the problem happens.
1) We have a filesystem mounted in RW mode and the qgroup rescan worker is
running;
2) We remount the filesystem in RO mode, and never stop/pause the rescan
worker, so after the remount the rescan worker is still running. The
important detail here is that the rescan task is still running after
the remount operation committed any ongoing transaction through its
call to btrfs_commit_super();
3) The rescan is still running, and after the remount completed, the
rescan worker started a transaction, after it finished iterating all
leaves of the extent tree, to update the qgroup status item in the
quotas tree. It does not commit the transaction, it only releases its
handle on the transaction;
4) A filesystem unmount operation starts shortly after;
5) The unmount task, at close_ctree(), stops the transaction kthread,
which had not had a chance to commit the open transaction since it was
sleeping and the commit interval (default of 30 seconds) has not yet
elapsed since the last time it committed a transaction;
6) So after stopping the transaction kthread we still have the transaction
used to update the qgroup status item open. At close_ctree(), when the
filesystem is in RO mode and no transaction abort happened (or the
filesystem is in error mode), we do not expect to have any transaction
open, so we do not call btrfs_commit_super();
7) We then proceed to destroy the work queues, free the roots and block
groups, etc. After that we drop the last reference on the btree inode
by calling iput() on it. Since there are dirty pages for the btree
inode, corresponding to the COWed extent buffer for the quotas btree,
btree_write_cache_pages() is invoked to flush those dirty pages. This
results in creating a bio and submitting it, which makes us end up at
btrfs_submit_metadata_bio();
8) At btrfs_submit_metadata_bio() we end up at the if-then-else branch
that calls btrfs_wq_submit_bio(), because check_async_write() returned
a value of 1. This value of 1 is because we did not have hardware
acceleration available for crc32c, so BTRFS_FS_CSUM_IMPL_FAST was not
set in fs_info->flags;
9) Then at btrfs_wq_submit_bio() we call btrfs_queue_work() against the
workqueue at fs_info->workers, which was already freed before by the
call to btrfs_stop_all_workers() at close_ctree(). This results in an
invalid memory access due to a use-after-free, leading to a crash.
When this happens, before the crash there are several warnings triggered,
since we have reserved metadata space in a block group, the delayed refs
reservation, etc:
Finally when we remove the btrfs module (rmmod btrfs), there are several
warnings about objects that were allocated from our slabs but were never
freed, consequence of the transaction that was never committed and got
leaked:
=============================================================================
BUG btrfs_delayed_ref_head (Tainted: G B W ): Objects remaining in btrfs_delayed_ref_head on __kmem_cache_shutdown()
-----------------------------------------------------------------------------
Fix this issue by having the remount path stop the qgroup rescan worker
when we are remounting RO and teach the rescan worker to stop when a
remount is in progress. If later a remount in RW mode happens, we are
already resuming the qgroup rescan worker through the call to
btrfs_qgroup_rescan_resume(), so we do not need to worry about that.
Tested-by: Fabian Vogt <fvogt@suse.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The top-level boot_targets (uImage and uImage.*) should be phony
targets. They just let Kbuild descend into arch/arc/boot/ and create
files there.
If a file exists in the top directory with the same name, the boot
image will not be created.
You can confirm it by the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig all # vmlinux will be built
$ touch uImage.gz
$ make ARCH=arc uImage.gz
CALL scripts/atomic/check-atomics.sh
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
# arch/arc/boot/uImage.gz is not created
arch/arc/boot/Makefile supports uImage.lzma, but you cannot do
'make uImage.lzma' because the corresponding target is missing
in arch/arc/Makefile. Add it.
I also changed the assignment operator '+=' to ':=' since this is the
only place where we expect this variable to be set.
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make ARCH=arc bindeb-pkg
SORTTAB vmlinux
SYSMAP System.map
MODPOST Module.symvers
make KERNELRELEASE=5.10.0-rc4 ARCH=arc KBUILD_BUILD_VERSION=2 -f ./Makefile intdeb-pkg
sh ./scripts/package/builddeb
cp: cannot stat 'arch/arc/boot/bootpImage': No such file or directory
make[4]: *** [scripts/Makefile.package:87: intdeb-pkg] Error 1
make[3]: *** [Makefile:1527: intdeb-pkg] Error 2
make[2]: *** [debian/rules:13: binary-arch] Error 2
dpkg-buildpackage: error: debian/rules binary subprocess returned exit status 2
make[1]: *** [scripts/Makefile.package:83: bindeb-pkg] Error 2
make: *** [Makefile:1527: bindeb-pkg] Error 2
The reason is obvious; arch/arc/Makefile sets $(boot)/bootpImage as
the default image, but there is no rule to build it.
Remove the meaningless KBUILD_IMAGE assignment so it will fallback
to the default vmlinux. With this change, you can build the deb package.
I removed the 'bootpImage' target as well. At best, it provides
'make bootpImage' as an alias of 'make vmlinux', but I do not see
much sense in doing so.
We got a "deleted inode referenced" warning cross our fsstress test. The
bug can be reproduced easily with following steps:
cd /dev/shm
mkdir test/
fallocate -l 128M img
mkfs.ext4 -b 1024 img
mount img test/
dd if=/dev/zero of=test/foo bs=1M count=128
mkdir test/dir/ && cd test/dir/
for ((i=0;i<1000;i++)); do touch file$i; done # consume all block
cd ~ && renameat2(AT_FDCWD, /dev/shm/test/dir/file1, AT_FDCWD,
/dev/shm/test/dir/dst_file, RENAME_WHITEOUT) # ext4_add_entry in
ext4_rename will return ENOSPC!!
cd /dev/shm/ && umount test/ && mount img test/ && ls -li test/dir/file1
We will get the output:
"ls: cannot access 'test/dir/file1': Structure needs cleaning"
and the dmesg show:
"EXT4-fs error (device loop0): ext4_lookup:1626: inode #2049: comm ls:
deleted inode referenced: 139"
ext4_rename will create a special inode for whiteout and use this 'ino'
to replace the source file's dir entry 'ino'. Once error happens
latter(the error above was the ENOSPC return from ext4_add_entry in
ext4_rename since all space has been consumed), the cleanup do drop the
nlink for whiteout, but forget to restore 'ino' with source file. This
will trigger the bug describle as above.
Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@vger.kernel.org Fixes: cd808deced43 ("ext4: support RENAME_WHITEOUT") Link: https://lore.kernel.org/r/20210105062857.3566-1-yangerkun@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online> Tested-by: Leon Schuermann <leon@is.currently.online> Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the origin device has a volatile write-back cache and the following
events occur:
1: After finishing merge operation of one set of exceptions,
merge_callback() is invoked.
2: Update the metadata in COW device tracking the merge completion.
This update to COW device is flushed cleanly.
3: System crashes and the origin device's cache where the recent
merge was completed has not been flushed.
During the next cycle when we read the metadata from the COW device,
we will skip reading those metadata whose merge was completed in
step (1). This will lead to data loss/corruption.
To address this, flush the origin device post merge IO before
updating the metadata.
This is because of the recent buffer overflow detection in the
commit 6a39e62abbaf ("lib: string.h: detect intra-object overflow in
fortified string functions")
Here acpi_device_bus_id->bus_id can only hold 14 characters, while the
the acpi_device_hid(device) returns a 22-char string
"HYPER_V_GEN_COUNTER_V1".
Per ACPI Spec v6.2, Section 6.1.5 _HID (Hardware ID), if the ID is a
string, it must be of the form AAA#### or NNNN####, i.e. 7 chars or 8
chars.
The field bus_id in struct acpi_device_bus_id was originally defined as
char bus_id[9], and later was enlarged to char bus_id[15] in 2007 in the
commit bb0958544f3c ("ACPI: use more understandable bus_id for ACPI
devices")
Fix the issue by changing the field bus_id to const char *, and use
kstrdup_const() to initialize it.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Tested-By: Jethro Beekman <jethro@fortanix.com>
[ rjw: Subject change, whitespace adjustment ] Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LLVM-built Linux triggered a boot hangup with KASLR enabled.
arch/mips/kernel/relocate.c:get_random_boot() uses linux_banner,
which is a string constant, as a random seed, but accesses it
as an array of unsigned long (in rotate_xor()).
When the address of linux_banner is not aligned to sizeof(long),
such access emits unaligned access exception and hangs the kernel.
Use PTR_ALIGN() to align input address to sizeof(long) and also
align down the input length to prevent possible access-beyond-end.
The compressed payload is not necesarily 4-byte aligned, at least when
compiling with Clang. In that case, the 4-byte value appended to the
compressed payload that corresponds to the uncompressed kernel image
size must be read using get_unaligned_le32().
This fixes Clang-built kernels not booting on MIPS (tested on a Ingenic
JZ4770 board).
Fixes: b8f54f2cde78 ("MIPS: ZBOOT: copy appended dtb to the end of the kernel") Cc: <stable@vger.kernel.org> # v4.7 Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the notrace function check on the architecture which doesn't
support kprobes on ftrace but support dynamic ftrace. This notrace
function check is not only for the kprobes on ftrace but also
sw-breakpoint based kprobes.
Thus there is no reason to limit this check for the arch which
supports kprobes on ftrace.
This also changes the dependency of Kconfig. Because kprobe event
uses the function tracer's address list for identifying notrace
function, if the CONFIG_DYNAMIC_FTRACE=n, it can not check whether
the target function is notrace or not.
We've observed crashes due to an empty cpu mask in
hyperv_flush_tlb_others. Obviously the cpu mask in question is changed
between the cpumask_empty call at the beginning of the function and when
it is actually used later.
One theory is that an interrupt comes in between and a code path ends up
changing the mask. Move the check after interrupt has been disabled to
see if it fixes the issue.
projects / users / dwmw2 / linux.git / log