We've found Samsung USBC Headset (AKG) (VID: 0x04e8, PID: 0xa051)
need a tiny delay after each class compliant request.
Otherwise the device might not be able to be recognized each times.
fix error "clock source 41 is not valid, cannot use"
[] New USB device found, idVendor=154e, idProduct=1002, bcdDevice= 1.00
[] New USB device strings: Mfr=1, Product=2, SerialNumber=0
[] Product: DCD-1500RE
[] Manufacturer: D & M Holdings Inc.
[]
[] clock source 41 is not valid, cannot use
[] usbcore: registered new interface driver snd-usb-audio
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ehci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
When runtime suspend was enabled, runtime suspend might happen
when xhci is removing hcd. This might cause kernel panic when hcd
has been freed but runtime pm suspend related handle need to
reference it.
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c19997 ("USB: ehci: add workaround for Synopsys HC bug")
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3bb9 ("usb: dwc2: Move gadget probe function into platform code") Reported-by: kbuild test robot <lkp@intel.com> Tested-by: Marek Vasut <marex@denx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binder driver makes the assumption proc->context pointer is invariant after
initialization (as documented in the kerneldoc header for struct proc).
However, in commit f0fe2c0f050d ("binder: prevent UAF for binderfs devices II")
proc->context is set to NULL during binder_deferred_release().
Another proc was in the middle of setting up a transaction to the dying
process and crashed on a NULL pointer deref on "context" which is a local
set to &proc->context:
The fix is to move the kfree of the binder_device to binder_free_proc()
so the binder_device is freed when we know there are no references
remaining on the binder_proc.
With the recent full-duplex support of implicit feedback streams, an
endpoint can be still running after closing the capture stream as long
as the playback stream with the sync-endpoint is running. In such a
state, the URBs are still be handled and they may call retire_data_urb
callback, which tries to transfer the data from the PCM buffer. Since
the PCM stream gets closed, this may lead to use-after-free.
This patch adds the proper clearance of the callback at stopping the
capture stream for addressing the possible UAF above.
Fixes: 10ce77e4817f ("ALSA: usb-audio: Add duplex sound support for USB devices using implicit feedback") Link: https://lore.kernel.org/r/20200616120921.12249-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the quiesce/activate rework, __netdev_watchdog_up() is directly
called in the ucc_geth driver.
Unfortunately, this function is not available for modules and thus
ucc_geth cannot be built as a module anymore. Fix it by exporting
__netdev_watchdog_up().
Since the commit introducing the regression was backported to stable
branches, this one should ideally be as well.
Fixes: 79dde73cf9bc ("net/ethernet/freescale: rework quiesce/activate for ucc_geth") Signed-off-by: Valentin Longchamp <valentin@longchamp.me> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a block group, if we fail to delete the block group's item
from the extent tree, we jump to the 'out' label and end up decrementing
the block group's reference count once only (by 1), resulting in a counter
leak because the block group at that point was already removed from the
block group cache rbtree - so we have to decrement the reference count
twice, once for the rbtree and once for our lookup at the start of the
function.
There is a second bug where if removing the free space tree entries (the
call to remove_block_group_free_space()) fails we end up jumping to the
'out_put_group' label but end up decrementing the reference count only
once, when we should have done it twice, since we have already removed
the block group from the block group cache rbtree. This happens because
the reference count decrement for the rbtree reference happens after
attempting to remove the free space tree entries, which is far away from
the place where we remove the block group from the rbtree.
To make things less error prone, decrement the reference count for the
rbtree immediately after removing the block group from it. This also
eleminates the need for two different exit labels on error, renaming
'out_put_label' to just 'out' and removing the old 'out'.
Fixes: f6033c5e333238 ("btrfs: fix block group leak when removing fails") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's not safe to use pm_runtime_force_{suspend,resume}(), especially
during the noirq phase of suspend. See also the guidance provided in
commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM
and system sleep (v2)").
Mirja Kuehlewind reported a bug in Linux TCP CUBIC Hystart, where
Hystart HYSTART_DELAY mechanism can exit Slow Start spuriously on an
ACK when the minimum rtt of a connection goes down. From inspection it
is clear from the existing code that this could happen in an example
like the following:
o The first 8 RTT samples in a round trip are 150ms, resulting in a
curr_rtt of 150ms and a delay_min of 150ms.
o The 9th RTT sample is 100ms. The curr_rtt does not change after the
first 8 samples, so curr_rtt remains 150ms. But delay_min can be
lowered at any time, so delay_min falls to 100ms. The code executes
the HYSTART_DELAY comparison between curr_rtt of 150ms and delay_min
of 100ms, and the curr_rtt is declared far enough above delay_min to
force a (spurious) exit of Slow start.
The fix here is simple: allow every RTT sample in a round trip to
lower the curr_rtt.
Fixes: ae27e98a5152 ("[TCP] CUBIC v2.3") Reported-by: Mirja Kuehlewind <mirja.kuehlewind@ericsson.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I spotted a few nits when comparing the in-tree version of sch_cake with
the out-of-tree one: A redundant error variable declaration shadowing an
outer declaration, and an indentation alignment issue. Fix both of these.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a further optimisation of the diffserv parsing codepath, we can skip it
entirely if CAKE is configured to neither use diffserv-based
classification, nor to zero out the diffserv bits.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cake_handle_diffserv() tries to linearize mac and network header parts of
skb and to make it writable unconditionally. In some cases it leads to full
skb reallocation, which reduces throughput and increases CPU load. Some
measurements of IPv4 forward + NAPT on MIPS router with 580 MHz single-core
CPU was conducted. It appears that on kernel 4.9 skb_try_make_writable()
reallocates skb, if skb was allocated in ethernet driver via so-called
'build skb' method from page cache (it was discovered by strange increase
of kmalloc-2048 slab at first).
Obtain DSCP value via read-only skb_header_pointer() call, and leave
linearization only for DSCP bleaching or ECN CE setting. And, as an
additional optimisation, skip diffserv parsing entirely if it is not needed
by the current configuration.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits") Signed-off-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
[ fix a few style issues, reflow commit message ] Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the datapath, the ip_tunnel_lookup() is used and it internally uses
fallback tunnel device pointer, which is fb_tunnel_dev.
This pointer variable should be set to NULL when a fb interface is deleted.
But there is no routine to set fb_tunnel_dev pointer to NULL.
So, this pointer will be still used after interface is deleted and
it eventually results in the use-after-free problem.
Test commands:
ip netns add A
ip netns add B
ip link add eth0 type veth peer name eth1
ip link set eth0 netns A
ip link set eth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set eth0 up
ip netns exec A ip link add gre1 type gre local 10.0.0.1 \
remote 10.0.0.2
ip netns exec A ip link set gre1 up
ip netns exec A ip a a 10.0.100.1/24 dev gre1
ip netns exec A ip a a 10.0.0.1/24 dev eth0
ip netns exec B ip link set lo up
ip netns exec B ip link set eth1 up
ip netns exec B ip link add gre1 type gre local 10.0.0.2 \
remote 10.0.0.1
ip netns exec B ip link set gre1 up
ip netns exec B ip a a 10.0.100.2/24 dev gre1
ip netns exec B ip a a 10.0.0.2/24 dev eth1
ip netns exec A hping3 10.0.100.2 -2 --flood -d 60000 &
ip netns del B
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 02a6efcab675 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.
In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).
The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.
Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.
Fixes: 02a6efcab675 ("net: phy: allow scanning busses with missing phys") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the datapath, the ip6gre_tunnel_lookup() is used and it internally uses
fallback tunnel device pointer, which is fb_tunnel_dev.
This pointer variable should be set to NULL when a fb interface is deleted.
But there is no routine to set fb_tunnel_dev pointer to NULL.
So, this pointer will be still used after interface is deleted and
it eventually results in the use-after-free problem.
Test commands:
ip netns add A
ip netns add B
ip link add eth0 type veth peer name eth1
ip link set eth0 netns A
ip link set eth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set eth0 up
ip netns exec A ip link add ip6gre1 type ip6gre local fc:0::1 \
remote fc:0::2
ip netns exec A ip -6 a a fc:100::1/64 dev ip6gre1
ip netns exec A ip link set ip6gre1 up
ip netns exec A ip -6 a a fc:0::1/64 dev eth0
ip netns exec A ip link set ip6gre0 up
ip netns exec B ip link set lo up
ip netns exec B ip link set eth1 up
ip netns exec B ip link add ip6gre1 type ip6gre local fc:0::2 \
remote fc:0::1
ip netns exec B ip -6 a a fc:100::2/64 dev ip6gre1
ip netns exec B ip link set ip6gre1 up
ip netns exec B ip -6 a a fc:0::2/64 dev eth1
ip netns exec B ip link set ip6gre0 up
ip netns exec A ping fc:100::2 -s 60000 &
ip netns del B
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver function tg3_io_error_detected() calls napi_disable twice,
without an intervening napi_enable, when the number of EEH errors exceeds
eeh_max_freezes, resulting in an indefinite sleep while holding rtnl_lock.
Add check for pcierr_recovery which skips code already executed for the
"Frozen" state.
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2013, we made a change that broke fast retransmit
for non SACK flows.
Indeed, for these flows, a sender needs to receive three duplicate
ACK before starting fast retransmit. Sending ACK with different
receive window do not count.
Even if enabling SACK is strongly recommended these days,
there still are some cases where it has to be disabled.
Not increasing the window seems better than having to
rely on RTO.
// Pure ACK received
+0.01 <[noecn] W. 14001:14001(0) ack 2001 win 65535
// Since CWR was sent, this packet should NOT have ECE set
+0.1 write(3, ..., 1000) = 1000
+0.0 >[ect0] P. 2001:3001(1000) ack 14001
// but Linux will still keep ECE latched here, with packetdrill
// flagging a missing ECE flag, expecting
// >[ect0] PE. 2001:3001(1000) ack 14001
// in the script
In the situation above we will continue to send ECN ECHO packets
and trigger the peer to reduce the congestion window. To avoid that
we can check CWR on pure ACKs received.
v3:
- Add a sequence check to avoid sending an ACK to an ACK
v2:
- Adjusted the comment
- move CWR check before checking for unacknowledged packets
Signed-off-by: Denis Kirjanov <denis.kirjanov@suse.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a socket is set ipv6only, it will still send IPv4 addresses in the
INIT and INIT_ACK packets. This potentially misleads the peer into using
them, which then would cause association termination.
The fix is to not add IPv4 addresses to ipv6only sockets.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Tested-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When preallocated service calls are being discarded, they're passed to
->discard_new_call() to have the caller clean up any attached higher-layer
preallocated pieces before being marked completed. However, the act of
marking them completed now invokes the call's notification function - which
causes a problem because that function might assume that the previously
freed pieces of memory are still there.
Fix this by setting a dummy notification function on the socket after
calling ->discard_new_call().
This results in the following kasan message when the kafs module is
removed.
==================================================================
BUG: KASAN: use-after-free in afs_wake_up_async_call+0x6aa/0x770 fs/afs/rxrpc.c:707
Write of size 1 at addr ffff8880946c39e4 by task kworker/u4:1/21
In rocker_dma_rings_init, the goto blocks in case of errors
caused by the functions rocker_dma_cmd_ring_waits_alloc() and
rocker_dma_ring_create() are incorrect. The patch fixes the
order consistent with cleanup in rocker_dma_rings_fini().
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ovs connection tracking module performs de-fragmentation on incoming
fragmented traffic. Take info account if traffic has been de-fragmented
in execute_check_pkt_len action otherwise we will perform the wrong
nested action considering the original packet size. This issue typically
occurs if ovs-vswitchd adds a rule in the pipeline that requires connection
tracking (e.g. OVN stateful ACLs) before execute_check_pkt_len action.
Moreover take into account GSO fragment size for GSO packet in
execute_check_pkt_len routine
Fixes: 4d5ec89fc8d14 ("net: openvswitch: Add a new action check_pkt_len") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in commit f60e5990d9c1 ("ipv6: protect skb->sk accesses
from recursive dereference inside the stack") Hannes added code
so that IPv6 stack would not trust skb->sk for typical cases
where packet goes through 'standard' xmit path (__dev_queue_xmit())
Alas af_packet had a dev_direct_xmit() path that was not
dealing yet with xmit_recursion level.
Also change sk_mc_loop() to dump a stack once only.
f60e5990d9c1 ("ipv6: protect skb->sk accesses from recursive dereference inside the stack") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arp request address is error, this is because fib_table_lookup in
fib_check_nh lookup the destnation 9.9.9.9 nexthop, the scope of
the fib result is RT_SCOPE_LINK,the correct scope is RT_SCOPE_HOST.
Here I add a check of whether this is RT_TABLE_MAIN to solve this problem.
Fixes: 3bfd847203c6 ("net: Use passed in table for nexthop lookups") Signed-off-by: guodeqing <geffrey.guo@huawei.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If call_netdevice_notifiers() failed, then rollback_registered()
calls netdev_unregister_kobject() which holds the kobject. The
reference cannot be put because the netdev won't be add to todo
list, so it will leads a memleak, we need put the reference to
avoid memleak.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing the sock TX queue in sk_set_socket() might cause unexpected
out-of-order transmit when called from sock_orphan(), as outstanding
packets can pick a different TX queue and bypass the ones already queued.
This is undesired in general. More specifically, it breaks the in-order
scheduling property guarantee for device-offloaded TLS sockets.
Remove the call to sk_tx_queue_clear() in sk_set_socket(), and add it
explicitly only where needed.
Fixes: e022f0b4a03f ("net: Introduce sk_tx_queue_mapping") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, ->ndo_start_xmit() can be executed recursively only
10 times because of stack memory.
But, in the case of the vxlan, 10 recursion limit value results in
a stack overflow.
In the current code, the nested interface is limited by 8 depth.
There is no critical reason that the recursion limitation value should
be 10.
So, it would be good to be the same value with the limitation value of
nesting interface depth.
Test commands:
ip link add vxlan10 type vxlan vni 10 dstport 4789 srcport 4789 4789
ip link set vxlan10 up
ip a a 192.168.10.1/24 dev vxlan10
ip n a 192.168.10.2 dev vxlan10 lladdr fc:22:33:44:55:66 nud permanent
for i in {9..0}
do
let A=$i+1
ip link add vxlan$i type vxlan vni $i dstport 4789 srcport 4789 4789
ip link set vxlan$i up
ip a a 192.168.$i.1/24 dev vxlan$i
ip n a 192.168.$i.2 dev vxlan$i lladdr fc:22:33:44:55:66 nud permanent
bridge fdb add fc:22:33:44:55:66 dev vxlan$A dst 192.168.$i.2 self
done
hping3 192.168.10.2 -2 -d 60000
The eth_addr member is passed to ether_addr functions that require
2-byte alignment, therefore the member must be properly aligned
to avoid unaligned accesses.
Fixes: 6db6f0eae605 ("bridge: multicast to unicast") Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Felix Fietkau <nbd@nbd.name> Cc: stable@vger.kernel.org Signed-off-by: Thomas Martitz <t.martitz@avm.de> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ethtool rx and tx queue statistics are reporting wrong values.
Fix reading out the correct ones.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a84d01647989 ("mld: fix memory leak in mld_del_delrec()") fixed
the memory leak of MLD, but missing the ipv6_mc_destroy_dev() path, in
which mca_sources are leaked after ma_put().
Using ip6_mc_clear_src() to take care of the missing free.
Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when set link down") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max MTU limit defined for ibmveth is not accounting for
virtual ethernet buffer overhead, which is twenty-two additional
bytes set aside for the ethernet header and eight additional bytes
of an opaque handle reserved for use by the hypervisor. Update the
max MTU to reflect this overhead.
Fixes: d894be57ca92 ("ethernet: use net core MTU range checking in more drivers") Fixes: 110447f8269a ("ethernet: fix min/max MTU typos") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, trying to change the DF parameter of a geneve device does
nothing:
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
# ip link set geneve1 type geneve id 1 df unset
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
We just need to update the value in geneve_changelink.
Fixes: a025fb5f49ad ("geneve: Allow configuration of DF behaviour") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rings bitmap of an interrupt vector encodes
which of the device's rings were assigned to that
interrupt vector.
Hence the iteration range of the tx rings bitmap
(for_each_set_bit()) should be the total number of
Tx rings of that netdevice instead of the number of
rings assigned to the interrupt vector.
Since there are 2 cores, and one interrupt vector for
each core, the number of rings asigned to an interrupt
vector is half the number of available rings.
The impact of this error is that the upper half of the
tx rings could still generate interrupts during napi
polling.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7bf90e5afe3 ("block/bio-integrity: fix a memory leak bug") added
a kfree() for 'buf' if bio_integrity_add_page() returns '0'. However,
the object will be freed in bio_integrity_free() since 'bio->bi_opf' and
'bio->bi_integrity' were set previousy in bio_integrity_alloc().
Fixes: commit e7bf90e5afe3 ("block/bio-integrity: fix a memory leak bug") Signed-off-by: yu kuai <yukuai3@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bob Liu <bob.liu@oracle.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sequence counters write paths are critical sections that must never be
preempted, and blocking, even for CONFIG_PREEMPTION=n, is not allowed.
Commit 5dbe7c178d3f ("net: fix kernel deadlock with interface rename and
netdev name retrieval.") handled a deadlock, observed with
CONFIG_PREEMPTION=n, where the devnet_rename seqcount read side was
infinitely spinning: it got scheduled after the seqcount write side
blocked inside its own critical section.
To fix that deadlock, among other issues, the commit added a
cond_resched() inside the read side section. While this will get the
non-preemptible kernel eventually unstuck, the seqcount reader is fully
exhausting its slice just spinning -- until TIF_NEED_RESCHED is set.
The fix is also still broken: if the seqcount reader belongs to a
real-time scheduling policy, it can spin forever and the kernel will
livelock.
Disabling preemption over the seqcount write side critical section will
not work: inside it are a number of GFP_KERNEL allocations and mutex
locking through the drivers/base/ :: device_rename() call chain.
>From all the above, replace the seqcount with a rwsem.
Fixes: 5dbe7c178d3f (net: fix kernel deadlock with interface rename and netdev name retrieval.) Fixes: 30e6c9fa93cf (net: devnet_rename_seq should be a seqcount) Fixes: c91f6df2db49 (sockopt: Change getsockopt() of SO_BINDTODEVICE to return an interface name) Cc: <stable@vger.kernel.org> Reported-by: kbuild test robot <lkp@intel.com> [ v1 missing up_read() on error exit ] Reported-by: Dan Carpenter <dan.carpenter@oracle.com> [ v1 missing up_read() on error exit ] Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Update the comment to use CONFIG_PREEMPTION.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: netdev@vger.kernel.org Link: https://lore.kernel.org/r/20191015191821.11479-22-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calculating the hardware value for the duty from the hardware value of
the period resulted in a precision loss versus calculating it from the
clock rate directly.
(Also remove a cast that doesn't really need to be here)
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9ed ("MIPS: remove mips_swiotlb_ops") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled
The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.
This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver") Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Chen Yu <yu.c.chen@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
where _raw_spin_lock_irqsave triggers the kretprobe and installs
kretprobe_trampoline handler on _raw_spin_lock_irqsave return.
The kretprobe_trampoline handler is then executed with already
locked kretprobe_table_locks, and first thing it does is to
lock kretprobe_table_locks ;-) the whole lockup path like:
Post parse_probe_arg(), the FETCH_OP_DATA operation type is overwritten
to FETCH_OP_ST_STRING, as a result memory is never freed since
traceprobe_free_probe_arg() iterates only over SYMBOL and DATA op types
Setup fetch string operation correctly after fetch_op_data operation.
When a crypto template needs to be instantiated, CRYPTO_MSG_ALG_REQUEST
is sent to crypto_chain. cryptomgr_schedule_probe() handles this by
starting a thread to instantiate the template, then waiting for this
thread to complete via crypto_larval::completion.
This can deadlock because instantiating the template may require loading
modules, and this (apparently depending on userspace) may need to wait
for the crc-t10dif module (lib/crc-t10dif.c) to be loaded. But
crc-t10dif's module_init function uses crypto_register_notifier() and
therefore takes crypto_chain.rwsem for write. That can't proceed until
the notifier callback has finished, as it holds this semaphore for read.
Fix this by removing the wait on crypto_larval::completion from within
cryptomgr_schedule_probe(). It's actually unnecessary because
crypto_alg_mod_lookup() calls crypto_larval_wait() itself after sending
CRYPTO_MSG_ALG_REQUEST.
This only actually became a problem in v4.20 due to commit b76377543b73
("crc-t10dif: Pick better transform if one becomes available"), but the
unnecessary wait was much older.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207159 Reported-by: Mike Gerow <gerow@google.com> Fixes: 398710379f51 ("crypto: algapi - Move larval completion into algboss") Cc: <stable@vger.kernel.org> # v3.6+ Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reported-by: Kai Lüke <kai@kinvolk.io> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somewhere along the line the cap on the SG list length for receive
was lost. This patch restores it and removes the subsequent test
which is now redundant.
Fixes: 2d97591ef43d ("crypto: af_alg - consolidation of...") Cc: <stable@vger.kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm connector notifies userspace on hotplug event prematurely before
late_register and mode_object register completes. This leads to a race
between userspace and kernel on updating the IDR list. So, move the
notification to end of connector register.
Our __sgt_iter assumes that the scattergather list has at least one
element. But during construction we may fail in allocating the first
page, and so mark the first element as the terminator. This is
unexpected!
Writing to the devfreq sysfs nodes while the GPU is powered down can
result in a system crash (on a5xx) or a nasty GMU error (on a6xx):
$ /sys/class/devfreq/5000000.gpu# echo 500000000 > min_freq
[ 104.841625] platform 506a000.gmu: [drm:a6xx_gmu_set_oob]
*ERROR* Timeout waiting for GMU OOB set GPU_DCVS: 0x0
Despite the fact that we carefully try to suspend the devfreq device when
the hardware is powered down there are lots of holes in the governors that
don't check for the suspend state and blindly call into the devfreq
callbacks that end up triggering hardware reads in the GPU driver.
Call pm_runtime_get_if_in_use() in the gpu_busy() and gpu_set_freq()
callbacks to skip the hardware access if it isn't active.
v3: Only check pm_runtime_get_if_in_use() for == 0 per Eric Anholt
v2: Use pm_runtime_get_if_in_use() per Eric Anholt
Cc: stable@vger.kernel.org Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e2262663 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
If both the tracer and the tracee are compat processes, and gprs[2]
is assigned a value by __poke_user_compat, then the higher 32 bits
of gprs[2] are cleared, IS_ERR_VALUE() always returns false, and
syscall_get_error() always returns 0.
Fix the implementation by sign-extending the value for compat processes
the same way as x86 implementation does.
The bug was exposed to user space by commit 201766a20e30f ("ptrace: add
PTRACE_GET_SYSCALL_INFO request") and detected by strace test suite.
This change fixes strace syscall tampering on s390.
If the dentry name passed to ->d_compare() fits in dentry::d_iname, then
it may be concurrently modified by a rename. This can cause undefined
behavior (possibly out-of-bounds memory accesses or crashes) in
utf8_strncasecmp(), since fs/unicode/ isn't written to handle strings
that may be concurrently modified.
Fix this by first copying the filename to a stack buffer if needed.
This way we get a stable snapshot of the filename.
Fixes: 2c2eb7a300cd ("f2fs: Support case-insensitive file name lookups") Cc: <stable@vger.kernel.org> # v5.4+ Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Daniel Rosenberg <drosen@google.com> Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sharing f2fs_ci_compare() between comparing cached dentries
(f2fs_d_compare()) and comparing on-disk dentries (f2fs_match_name())
doesn't work as well as intended, as these actions fundamentally differ
in several ways (e.g. whether the task may sleep, whether the directory
is stable, whether the casefolded name was precomputed, whether the
dentry will need to be decrypted once we allow casefold+encrypt, etc.)
Just make f2fs_d_compare() implement what it needs directly, and rework
f2fs_ci_compare() to be specialized for f2fs_match_name().
Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For optimized block readers not holding a mutex, the "number of sectors"
64-bit value is protected from tearing on 32-bit architectures by a
sequence counter.
Disable preemption before entering that sequence counter's write side
critical section. Otherwise, the read side can preempt the write side
section and spin for the entire scheduler tick. If the reader belongs to
a real-time scheduling class, it can spin forever and the kernel will
livelock.
Fixes: c83f6bf98dc1 ("block: add partition resize function to blkpg ioctl") Cc: <stable@vger.kernel.org> Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The final build stage of the x86 kernel captures some symbol
addresses from the decompressor binary and copies them into zoffset.h.
It uses sed with a regular expression that matches the address, symbol
type and symbol name, and mangles the captured addresses and the names
of symbols of interest into #define directives that are added to
zoffset.h
The symbol type is indicated by a single letter, which we match
strictly: only letters in the set 'ABCDGRSTVW' are matched, even
though the actual symbol type is relevant and therefore ignored.
Commit bc7c9d620 ("efi/libstub/x86: Force 'hidden' visibility for
extern declarations") made a change to the way external symbol
references are classified, resulting in 'startup_32' now being
emitted as a hidden symbol. This prevents the use of GOT entries to
refer to this symbol via its absolute address, which recent toolchains
(including Clang based ones) already avoid by default, making this
change a no-op in the majority of cases.
However, as it turns out, the LLVM linker classifies such hidden
symbols as symbols with static linkage in fully linked ELF binaries,
causing tools such as NM to output a lowercase 't' rather than an upper
case 'T' for the type of such symbols. Since our sed expression only
matches upper case letters for the symbol type, the line describing
startup_32 is disregarded, resulting in a build error like the following
arch/x86/boot/header.S:568:18: error: symbol 'ZO_startup_32' can not be
undefined in a subtraction expression
init_size: .long (0x00000000008fd000 - ZO_startup_32 +
(((0x0000000001f6361c + ((0x0000000001f6361c >> 8) + 65536)
- 0x00000000008c32e5) + 4095) & ~4095)) # kernel initialization size
Given that we are only interested in the value of the symbol, let's match
any character in the set 'a-zA-Z' instead.
Currently we only poll for an ACT up to 30 times, with a busy-wait delay
of 100µs between each attempt - giving us a timeout of 2900µs. While
this might seem sensible, it would appear that in certain scenarios it
can take dramatically longer then that for us to receive an ACT. On one
of the EVGA MST hubs that I have available, I observed said hub
sometimes taking longer then a second before signalling the ACT. These
delays mostly seem to occur when previous sideband messages we've sent
are NAKd by the hub, however it wouldn't be particularly surprising if
it's possible to reproduce times like this simply by introducing branch
devices with large LCTs since payload allocations have to take effect on
every downstream device up to the payload's target.
So, instead of just retrying 30 times we poll for the ACT for up to 3ms,
and additionally use usleep_range() to avoid a very long and rude
busy-wait. Note that the previous retry count of 30 appears to have been
arbitrarily chosen, as I can't find any mention of a recommended timeout
or retry count for ACTs in the DisplayPort 2.0 specification. This also
goes for the range we were previously using for udelay(), although I
suspect that was just copied from the recommended delay for link
training on SST devices.
Changes since v1:
* Use readx_poll_timeout() instead of open-coding timeout loop - Sean
Paul
Changes since v2:
* Increase poll interval to 200us - Sean Paul
* Print status in hex when we timeout waiting for ACT - Sean Paul
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)") Cc: Sean Paul <sean@poorly.run> Cc: <stable@vger.kernel.org> # v3.17+ Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200406221253.1307209-4-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to change dax mount options when remounting could allow mount
options to be enabled for a small amount of time, and then the mount
option change would be reverted.
In the case of "mount -o remount,dax", this can cause a race where
files would temporarily treated as DAX --- and then not.
__jbd2_journal_abort_hard() is no longer used, so now we can merge
__jbd2_journal_abort_hard() and __journal_abort_soft() these two
functions into jbd2_journal_abort() and remove them.
Clang's static analysis tool reports these double free memory errors.
security/selinux/ss/services.c:2987:4: warning: Attempt to free released memory [unix.Malloc]
kfree(bnames[i]);
^~~~~~~~~~~~~~~~
security/selinux/ss/services.c:2990:2: warning: Attempt to free released memory [unix.Malloc]
kfree(bvalues);
^~~~~~~~~~~~~~
So improve the security_get_bools error handling by freeing these variables
and setting their return pointers to NULL and the return len to 0
Cc: stable@vger.kernel.org Signed-off-by: Tom Rix <trix@redhat.com> Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializes Powertune data for a specific Hawaii card by fixing what
looks like a typo in the code. The device ID 66B1 is not a supported
device ID for this driver, and is not mentioned elsewhere. 67B1 is a
valid device ID, and is a Hawaii Pro GPU.
I have tested on my R9 390 which has device ID 67B1, and it works
fine without problems.
The command ring and cursor ring use different notify port addresses
definition: QXL_IO_NOTIFY_CMD and QXL_IO_NOTIFY_CURSOR. However, in
qxl_device_init() we use QXL_IO_NOTIFY_CMD to create both command ring
and cursor ring. This doesn't cause any problems now, because QEMU's
behaviors on QXL_IO_NOTIFY_CMD and QXL_IO_NOTIFY_CURSOR are the same.
However, QEMU's behavior may be change in future, so let's fix it.
P.S.: In the X.org QXL driver, the notify port address of cursor ring
is correct.
Just add a bit more line wrapping, get rid of some extraneous
whitespace, remove an unneeded goto label, and move around some variable
declarations. No functional changes here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
[this isn't a fix, but it's needed for the fix that comes after this] Fixes: ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)") Cc: Sean Paul <sean@poorly.run> Cc: <stable@vger.kernel.org> # v3.17+ Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200406221253.1307209-3-lyude@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the dentry name passed to ->d_compare() fits in dentry::d_iname, then
it may be concurrently modified by a rename. This can cause undefined
behavior (possibly out-of-bounds memory accesses or crashes) in
utf8_strncasecmp(), since fs/unicode/ isn't written to handle strings
that may be concurrently modified.
Fix this by first copying the filename to a stack buffer if needed.
This way we get a stable snapshot of the filename.
Fixes: b886ee3e778e ("ext4: Support case-insensitive file name lookups") Cc: <stable@vger.kernel.org> # v5.2+ Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Daniel Rosenberg <drosen@google.com> Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Link: https://lore.kernel.org/r/20200601200543.59417-1-ebiggers@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the bug when calculating the physical block number of the first
block in the split extent.
This bug will cause xfstests shared/298 failure on ext4 with bigalloc
enabled occasionally. Ext4 error messages indicate that previously freed
blocks are being freed again, and the following fsck will fail due to
the inconsistency of block bitmap and bg descriptor.
The following is an example case:
1. First, Initialize a ext4 filesystem with cluster size '16K', block size
'4K', in which case, one cluster contains four blocks.
2. Create one file (e.g., xxx.img) on this ext4 filesystem. Now the extent
tree of this file is like:
3. Then execute PUNCH_HOLE fallocate on this file. The hole range is
like:
..
ext4_ext_remove_space: dev 254,16 ino 12 since 49506 end 49506 depth 1
ext4_ext_remove_space: dev 254,16 ino 12 since 49544 end 49546 depth 1
ext4_ext_remove_space: dev 254,16 ino 12 since 49605 end 49607 depth 1
...
4. Then the extent tree of this file after punching is like
...
49507:[0]37:158047
49547:[0]58:158087
...
5. Detailed procedure of punching hole [49544, 49546]
5.3. The ftrace output when punching hole [49544, 49546]:
- ext4_ext_remove_space (start 49544, end 49546)
- ext4_ext_rm_leaf (start 49544, end 49546, last_extent [49507(158047), 40], partial [pclu 39522 lblk 0 state 2])
- ext4_remove_blocks (extent [49507(158047), 40], from 49544 to 49546, partial [pclu 39522 lblk 0 state 2]
- ext4_free_blocks: (block 158084 count 4)
- ext4_mballoc_free (extent 1/6753/1)
5.4. Ext4 error message in dmesg:
EXT4-fs error (device vdb): mb_free_blocks:1457: group 1, block 158084:freeing already freed block (bit 6753); block bitmap corrupt.
EXT4-fs error (device vdb): ext4_mb_generate_buddy:747: group 1, block bitmap and bg descriptor inconsistent: 19550 vs 19551 free clusters
In this case, the whole cluster 39521 is freed mistakenly when freeing
pblock 158084~158086 (i.e., the first three blocks of this cluster),
although pblock 158087 (the last remaining block of this cluster) has
not been freed yet.
The root cause of this isuue is that, the pclu of the partial cluster is
calculated mistakenly in ext4_ext_remove_space(). The correct
partial_cluster.pclu (i.e., the cluster number of the first block in the
next extent, that is, lblock 49597 (pblock 158086)) should be 39521 rather
than 39522.
Commit 130f4caf145c ("libata: Ensure ata_port probe has completed before
detach") may cause system freeze during suspend.
Using async_synchronize_full() in PM callbacks is wrong, since async
callbacks that are already scheduled may wait for not-yet-scheduled
callbacks, causes a circular dependency.
Instead of using big hammer like async_synchronize_full(), use async
cookie to make sure port probe are synced, without affecting other
scheduled PM callbacks.
Fixes: 130f4caf145c ("libata: Ensure ata_port probe has completed before detach") Suggested-by: John Garry <john.garry@huawei.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: John Garry <john.garry@huawei.com> BugLink: https://bugs.launchpad.net/bugs/1867983 Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. STTR) at EL1 can cause EL0 watchpoints to fire
unexpectedly if kernel debugging is enabled. In such cases, the
hw_breakpoint logic will invoke the user overflow handler which will
typically raise a SIGTRAP back to the current task. This is futile when
returning back to the kernel because (a) the signal won't have been
delivered and (b) userspace can't handle the thing anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
(Fixes tag identifies the introduction of unprivileged memory accesses,
which exposed this latent bug in the hw_breakpoint code)
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: James Morse <james.morse@arm.com> Fixes: 57f4959bad0a ("arm64: kernel: Add support for User Access Override") Reported-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The remove function does not destroy all
BM Pools when per cpu pool is active.
When reloading the mvpp2 as a module the BM Pools
are still active in hardware and due to the bug
have twice the size now old + new.
This eventually leads to a kernel crash.
v2:
* add Fixes tag
Fixes: 7d04b0b13b11 ("mvpp2: percpu buffers") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In blkdev_get() we call __blkdev_get() to do some internal jobs and if
there is some errors in __blkdev_get(), the bdput() is called which
means we have released the refcount of the bdev (actually the refcount of
the bdev inode). This means we cannot access bdev after that point. But
acctually bdev is still accessed in blkdev_get() after calling
__blkdev_get(). This results in use-after-free if the refcount is the
last one we released in __blkdev_get(). Let's take a look at the
following scenerio:
CPU0 CPU1 CPU2
blkdev_open blkdev_open Remove disk
bd_acquire
blkdev_get
__blkdev_get del_gendisk
bdev_unhash_inode
bd_acquire bdev_get_gendisk
bd_forget failed because of unhashed
bdput
bdput (the last one)
bdev_evict_inode
Fix this by delaying bdput() to the end of blkdev_get() which means we
have finished accessing bdev.
Fixes: 77ea887e433a ("implement in-kernel gendisk events handling") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Ming Lei <ming.lei@redhat.com> Cc: Jan Kara <jack@suse.cz> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ufs_bsg_alloc_desc_buffer() returns an error code, a pairing runtime
PM usage counter decrement is needed to keep the counter balanced.
Link: https://lore.kernel.org/r/20200522045932.31795-1-dinghao.liu@zju.edu.cn Fixes: 74e5e468b664 (scsi: ufs-bsg: Wake the device before sending raw upiu commands) Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Abort code UAEOVERFLOW is returned when we try and set a time that's out of
range, but it's currently mapped to EREMOTEIO by the default case.
Fix UAEOVERFLOW to map instead to EOVERFLOW.
Found with the generic/258 xfstest. Note that the test is wrong as it
assumes that the filesystem will support a pre-UNIX-epoch date.
Fixes: 1eda8bab70ca ("afs: Add support for the UAE error table") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set a flag in the call struct to indicate an unmarshalling error rather
than return and handle an error from the decoding of file statuses. This
flag is checked on a successful return from the delivery function.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a lookup is done in an AFS directory, the filesystem will speculate
and fetch up to 49 other statuses for files in the same directory and fetch
those as well, turning them into inodes or updating inodes that already
exist.
However, occasionally, a callback break might go missing due to NAT timing
out, but the afs filesystem doesn't then realise that the directory is not
up to date.
Alleviate this by using one of the status slots to check the directory in
which the lookup is being done.
Reported-by: Dave Botsch <botsch@cnf.cornell.edu> Suggested-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing a partial writeback, afs_write_back_from_locked_page() may
generate an FS.StoreData RPC request that writes out part of a file when a
file has been constructed from pieces by doing seek, write, seek, write,
... as is done by ld.
The FS.StoreData RPC is given the current i_size as the file length, but
the server basically ignores it unless the data length is 0 (in which case
it's just a truncate operation). The revised file length returned in the
result of the RPC may then not reflect what we suggested - and this leads
to i_size getting moved backwards - which causes issues later.
Fix the client to take account of this by ignoring the returned file size
unless the data version number jumped unexpectedly - in which case we're
going to have to clear the pagecache and reload anyway.
This can be observed when doing a kernel build on an AFS mount. The
following pair of commands produce the issue:
Fix afs_write_end() to change i_size under vnode->cb_lock rather than
->wb_lock so that it doesn't race with afs_vnode_commit_status() and
afs_getattr().
The ->wb_lock is only meant to guard access to ->wb_keys which isn't
accessed by that piece of code.
Fixes: 4343d00872e1 ("afs: Get rid of the afs_writeback record") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mtime on an inode needs to be updated when a write is made into an
mmap'ed section. There are three ways in which this could be done: update
it when page_mkwrite is called, update it when a page is changed from dirty
to writeback or leave it to the server and fix the mtime up from the reply
to the StoreData RPC.
With CONFIG_DEBUG_VIRTUAL=y, we can hit a BUG() if we take a hard
lockup watchdog interrupt when in OPAL mode.
This happens in show_instructions() if the kernel takes the watchdog
NMI IPI, or any other interrupt, with MSR_IR == 0. show_instructions()
updates the variable pc in the loop and the second iteration will
result in BUG().
coccicheck reports:
drivers/md//bcache/btree.c:1538:1-7: preceding lock on line 1417
In btree_gc_coalesce func, if the coalescing process fails, we will goto
to out_nocoalesce tag directly without releasing new_nodes[i]->write_lock.
Then, it will cause a deadlock when trying to acquire new_nodes[i]->
write_lock for freeing new_nodes[i] before return.
btree_gc_coalesce func details as follows:
if alloc new_nodes[i] fails:
goto out_nocoalesce;
// obtain new_nodes[i]->write_lock
mutex_lock(&new_nodes[i]->write_lock)
// main coalescing process
for (i = nodes - 1; i > 0; --i)
[snipped]
if coalescing process fails:
// Here, directly goto out_nocoalesce
// tag will cause a deadlock
goto out_nocoalesce;
[snipped]
// release new_nodes[i]->write_lock
mutex_unlock(&new_nodes[i]->write_lock)
// coalesing succ, return
return;
out_nocoalesce:
btree_node_free(new_nodes[i]) // free new_nodes[i]
// obtain new_nodes[i]->write_lock
mutex_lock(&new_nodes[i]->write_lock);
// set flag for reuse
clear_bit(BTREE_NODE_dirty, &ew_nodes[i]->flags);
// release new_nodes[i]->write_lock
mutex_unlock(&new_nodes[i]->write_lock);
To fix the problem, we add a new tag 'out_unlock_nocoalesce' for
releasing new_nodes[i]->write_lock before out_nocoalesce tag. If
coalescing process fails, we will go to out_unlock_nocoalesce tag
for releasing new_nodes[i]->write_lock before free new_nodes[i] in
out_nocoalesce tag.
Now the errcode from ext4_commit_super will overwrite EROFS exists in
ext4_setup_super. Actually, no need to call ext4_commit_super since we
will return EROFS. Fix it by goto done directly.
Fixes: c89128a00838 ("ext4: handle errors on ext4_commit_super") Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200601073404.3712492-1-yangerkun@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
If config->aggr_map is NULL and config->aggr_get_id is not NULL,
the function print_aggr() will still calling arrg_update_shadow(),
which can result in accessing the invalid pointer.
Fixes: 088519f318be ("perf stat: Move the display functions to stat-display.c") Signed-off-by: Hongbo Yao <yaohongbo@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wei Li <liwei391@huawei.com> Link: https://lore.kernel.org/lkml/20200608163625.GC3073@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
projects / users / dwmw2 / linux.git / log