The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b1206122069a ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem.
The problem was in wrong place for percpu_init_rwsem() call.
hci_uart_proto::open() may register a timer whose callback may call
hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device()
thread won't be fast enough to call percpu_init_rwsem().
Fix it my moving percpu_init_rwsem() call before p->open().
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9
...
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:951 [inline]
register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263
__lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906
lock_acquire kernel/locking/lockdep.c:5637 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602
percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline]
hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124
h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188
call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421
Syzbot has reported GPF in sg_alloc_append_table_from_pages(). The
problem was in ubuf->pages == ZERO_PTR.
ubuf->pagecount is calculated from arguments passed from user-space. If
user creates udmabuf with list.size == 0 then ubuf->pagecount will be
also equal to zero; it causes kmalloc_array() to return ZERO_PTR.
Fix it by validating ubuf->pagecount before passing it to
kmalloc_array().
When I checked the code in skeleton header file generated with my own
bpf prog, I found there may be possible NULL pointer dereference when
destroying skeleton. Then I checked the in-tree bpf progs, finding that is
a common issue. Let's take the generated samples/bpf/xdp_redirect_cpu.skel.h
for example. Below is the generated code in
xdp_redirect_cpu__create_skeleton():
xdp_redirect_cpu__create_skeleton
struct bpf_object_skeleton *s;
s = (struct bpf_object_skeleton *)calloc(1, sizeof(*s));
if (!s)
goto error;
...
error:
bpf_object__destroy_skeleton(s);
return -ENOMEM;
After goto error, the NULL 's' will be deferenced in
bpf_object__destroy_skeleton().
We can simply fix this issue by just adding a NULL check in
bpf_object__destroy_skeleton().
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
In function ath10k_wow_convert_8023_to_80211(), it will do memcpy for
the new->pattern, and currently the new->pattern and new->mask is same
with the old, then the memcpy of new->pattern will also overwrite the
old->pattern, because the header format of new->pattern is 802.11,
its length is larger than the old->pattern which is 802.3. Then the
operation of "Copy frame body" will copy a mistake value because the
body memory has been overwrite when memcpy the new->pattern.
Assign another empty value to new_pattern to avoid the overwrite issue.
Fixes: fa3440fa2fa1 ("ath10k: convert wow pattern from 802.3 to 802.11") Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211222031347.25463-1-quic_wgong@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: 44cfc6233447 ("drm/bridge: Add NWL MIPI DSI host controller support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220105104826.1418-1-linmq006@gmail.com Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rc_dev is allocated by rc_allocate_device(), and doesn't assigned to
ctx->rc_dev before calling rc_free_device(ctx->rc_dev).
So it should call rc_free_device(rc_dev);
Fixes: e25f1f7c94e1 ("drm/bridge/sii8620: add remote control support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211227092522.21755-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 06b93644f4d1 ("media: Kconfig: add an option to filter in/out
platform drivers") introduced CONFIG_MEDIA_PLATFORM_SUPPORT, to allow
more fine grained control over the inclusion of certain Kconfig files.
multi_v5_defconfig was selecting some drivers described in
drivers/media/platform/Kconfig, which now wasn't included anymore.
Explicitly set the new symbol in multi_v5_defconfig to bring those
drivers back.
This enables some new V4L2 and VIDEOBUF2 features, but as modules only.
Fixes: 06b93644f4d1 ("media: Kconfig: add an option to filter in/out platform drivers") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Link: https://lore.kernel.org/r/20220317183043.948432-3-andre.przywara@arm.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
This is similar to commit 64b92de9603f
("ASoC: wcd9335: fix a leaked reference by adding missing of_node_put")
Fixes: a61f3b4f476e ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220316083631.14103-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call , as already done in the remove function.
Fixes: de66b3455023 ("ASoC: codecs: msm8916-wcd-analog: add MBHC support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220316041924.17560-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TX clock source may be changed in next case, need to
disable it when stop, otherwise the TX may not work after
changing the clock source, error log is:
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error paths.
For example, when codec_np is NULL, saif_np[0] and saif_np[1]
are not NULL, it will cause leaks.
of_node_put() will check if the node pointer is NULL, so we can
call it directly to release the refcount of regular pointers.
Fixes: e968194b45c4 ("ASoC: mxs: add device tree support for mxs-sgtl5000") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220308020146.26496-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VIDIOC_G_FBUF and related overlay ioctls no longer worked (-ENOTTY was
returned).
The root cause was the introduction of the caps field in ivtv-driver.h.
While loading the ivtvfb module would update the video_device device_caps
field with V4L2_CAP_VIDEO_OUTPUT_OVERLAY it would not update that caps
field, and that's what the overlay ioctls would look at.
It's a bad idea to keep information in two places, so drop the caps field
and only use vdev.device_caps.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de> Fixes: 2161536516ed (media: media/pci: set device_caps in struct video_device) Signed-off-by: Sasha Levin <sashal@kernel.org>
'dev' will *always* be set by list_for_each_entry().
It is incorrect to assume that the iterator value will be NULL if the
list is empty.
Instead of checking the pointer it should be checked if
the list is empty.
Fixes: 79dd0c69f05f ("V4L: 925: saa7134 alsa is now a standalone module") Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid the same code.
Fixes: a6ba2b2dabb5 ("ASoC: Implement WM8350 headphone jack detection") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220304023821.391936-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the possible failure of the vzalloc(), e->encoder_buf might be NULL.
Therefore, it should be better to check it in order
to guarantee the success of the initialization.
If fails, we need to free not only 'e' but also 'e->name'.
Also, if the allocation for ctx fails, we need to free 'e->encoder_buf'
else.
If the callback 'start_streaming' fails, then all
queued buffers in the driver should be returned with
state 'VB2_BUF_STATE_QUEUED'. Currently, they are
returned with 'VB2_BUF_STATE_ERROR' which is wrong.
Fix this. This also fixes the warning:
When CONFIG_MCF_EDMA is set (due to COMPILE_TEST, not due to
CONFIG_M5441x), coldfire/device.c has compile errors due to
missing MCFEDMA_* symbols. In the .config file that was provided,
CONFIG_M5206=y, not CONFIG_M5441x, so <asm/m5441xsim.h> is not
included in coldfire/device.c.
Only build the MCF_EDMA code in coldfire/device.c if the MCFEDMA_*
hardware macros are defined.
Fixes these build errors:
../arch/m68k/coldfire/device.c:512:35: error: 'MCFEDMA_BASE' undeclared here (not in a function); did you mean 'MCFDMA_BASE1'?
512 | .start = MCFEDMA_BASE,
../arch/m68k/coldfire/device.c:513:50: error: 'MCFEDMA_SIZE' undeclared here (not in a function)
513 | .end = MCFEDMA_BASE + MCFEDMA_SIZE - 1,
../arch/m68k/coldfire/device.c:517:35: error: 'MCFEDMA_IRQ_INTR0' undeclared here (not in a function)
517 | .start = MCFEDMA_IRQ_INTR0,
../arch/m68k/coldfire/device.c:523:35: error: 'MCFEDMA_IRQ_INTR16' undeclared here (not in a function)
523 | .start = MCFEDMA_IRQ_INTR16,
../arch/m68k/coldfire/device.c:529:35: error: 'MCFEDMA_IRQ_INTR56' undeclared here (not in a function)
529 | .start = MCFEDMA_IRQ_INTR56,
../arch/m68k/coldfire/device.c:535:35: error: 'MCFEDMA_IRQ_ERR' undeclared here (not in a function)
535 | .start = MCFEDMA_IRQ_ERR,
AV/C deferred transaction was supported at a commit 00a7bb81c20f ("ALSA:
firewire-lib: Add support for deferred transaction") while 'deferrable'
flag can be uninitialized for non-control/notify AV/C transactions.
UBSAN reports it:
This commit fixes the bug. The bug has no disadvantage for the non-
control/notify AV/C transactions since the flag has an effect for AV/C
response with INTERIM (0x0f) status which is not used for the transactions
in AV/C general specification.
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value of the
setup_interrupts() and return error if fails.
Fixes: 68b4aee35d1f ("memory: emif: add interrupt and temperature handling") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20220224025444.3256530-1-jiasheng@iscas.ac.cn Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is one call trace that snd_soc_register_card()
->snd_soc_bind_card()->soc_init_pcm_runtime()
->snd_soc_dai_compress_new()->snd_soc_new_compress().
In the trace the 'codec_dai' transfers from card->dai_link,
and we can see from the snd_soc_add_pcm_runtime() in
snd_soc_bind_card() that, if value of card->dai_link->num_codecs
is 0, then 'codec_dai' could be null pointer caused
by index out of bound in 'asoc_rtd_to_codec(rtd, 0)'.
And snd_soc_register_card() is called by various platforms.
Therefore, it is better to add the check in the case of misusing.
And because 'cpu_dai' has already checked in soc_init_pcm_runtime(),
there is no need to check again.
Adding the check as follow, then if 'codec_dai' is null,
snd_soc_new_compress() will not pass through the check
'if (playback + capture != 1)', avoiding the leftover use of
'codec_dai'.
Fixes: 467fece ("ASoC: soc-dai: move snd_soc_dai_stream_valid() to soc-dai.c") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/1634285633-529368-1-git-send-email-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it, as same as clk_prepare_enable().
Fixes: c9afc1834e81 ("ASoC: dwc: Disallow building designware_pcm as a module") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20220301084742.3751939-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it, like mxs_saif_trigger().
Fixes: d0ba4c014934 ("ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20220301081717.3727190-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an invalid option value is used with "printk.devkmsg=<value>",
it is silently ignored.
If a valid option value is used, it is honored but the wrong return
value (0) is used, indicating that the command line option had an
error and was not handled. This string is not added to init's
environment strings due to init/main.c::unknown_bootoption()
checking for a '.' in the boot option string and then considering
that string to be an "Unused module parameter".
Print a warning message if a bad option string is used.
Always return 1 from the __setup handler to indicate that the command
line option has been handled.
Fixes: 750afe7babd1 ("printk: add kernel parameter to control writes to /dev/kmsg") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Borislav Petkov <bp@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: John Ogness <john.ogness@linutronix.de> Reviewed-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20220228220556.23484-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Broadcom ns2 platform has spi-cpol and spi-cpho properties set
incorrectly. As per spi-slave-peripheral-prop.yaml, these properties are
of flag or boolean type and not integer type. Fix the values.
Fixes: d69dbd9f41a7c (arm64: dts: Add ARM PL022 SPI DT nodes for NS2) Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com> CC: Ray Jui <rjui@broadcom.com> CC: Scott Branden <sbranden@broadcom.com> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: 5f9a50c3e55e ("ASoC: Davinci: McBSP: add device tree support for McBSP") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com> Link: https://lore.kernel.org/r/20220228031540.3571959-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function devm_kzalloc() in rt5663_parse_dp() can fail, so its return
value should be checked.
Fixes: 457c25efc592 ("ASoC: rt5663: Add the function of impedance sensing") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Link: https://lore.kernel.org/r/20220225131030.27248-1-baijiaju1990@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to BSP library source, H264 neighbour info buffer size needs
to be 32 kiB for H6. This is similar to H265 decoding, which also needs
double buffer size in comparison to older Cedrus core generations.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Issue was discovered using iommu and cross checked with BSP library
source.
Neighbour info buffer size needs to be 794 kiB in H6. This is actually
already indirectly mentioned in the comment, but smaller size is used
nevertheless.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Bug was discovered using iommu, which reported access error when trying
to play H265 video.
Call i2c_unregister_device(audio) on this error path.
Fixes: d3b2ccd9e307 ("[media] s2250: convert to the control framework") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 47677e51e2a4("[media] em28xx: Only deallocate struct
em28xx after finishing all extensions") adds kref_get to many init
functions (e.g., em28xx_audio_init). However, kref_init is called too
late in em28xx_usb_probe, since em28xx_init_dev before will invoke
those init functions and call kref_get function. Then refcount bug
occurs in my local syzkaller instance.
Fix it by moving kref_init before em28xx_init_dev. This issue occurs
not only in dev but also dev->dev_next.
Fixes: 47677e51e2a4 ("[media] em28xx: Only deallocate struct em28xx after finishing all extensions") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling hdmi_infoframe_unpack() with static sizeof(buffer) skips all
the size checking done later in hdmi_infoframe_unpack(). A better
value is the amount of data read into buffer.
Fixes: 480b8b3e42c3 ("video/hdmi: Pass buffer size to infoframe unpack functions") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The M53Menlo display unit uses an LVDS-to-DPI bridge, TI DS90CF364A.
Describe this bridge in DT, otherwise the DT incorrectly describes
DPI panel attached directly to LVDS source.
replace millivolt with correct microvolt and adjust value to
the minimal value allowed by documentation.
Found with `make qcom/sdm845-oneplus-fajita.dtb`.
Fixes:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias2-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias3-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias4-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-millivolt', 'qcom,micbias2-millivolt', 'qcom,micbias3-millivolt', 'qcom,micbias4-millivolt' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'
Quoting the header comments, IRQF_ONESHOT is "Used by threaded interrupts
which need to keep the irq line disabled until the threaded handler has
been run.". When applied to an interrupt that doesn't request a threaded
irq then IRQF_ONESHOT has a lesser known (undocumented?) side effect,
which it to disable the forced threading of the irq. For "normal" kernels
(without forced threading) then, if there is no thread_fn, then
IRQF_ONESHOT is a nop.
In this case disabling forced threading is not appropriate for this driver
because it calls wake_up_all() and this API cannot be called from
no-thread interrupt handlers on PREEMPT_RT systems (deadlock risk, triggers
sleeping-while-atomic warnings).
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Because of the possible failure of the allocation, data->domains might
be NULL pointer and will cause the dereference of the NULL pointer
later.
Therefore, it might be better to check it and directly return -ENOMEM
without releasing data manually if fails, because the comment of the
devm_kmalloc() says "Memory allocated with this function is
automatically freed on driver detach.".
Fixes: bbe3a66c3f5a ("soc: qcom: rpmpd: Add a Power domain driver to model corners") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20211231094419.1941054-1-jiasheng@iscas.ac.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
Member assignments to qcom_scm_desc were moved into struct initializers
in 57d3b816718c ("firmware: qcom_scm: Remove thin wrappers") including
the case in qcom_scm_iommu_secure_ptbl_init, except that the - now
duplicate - assignment to desc was left in place. While not harmful,
remove this unnecessary extra reassignment.
Fixes: 57d3b816718c ("firmware: qcom_scm: Remove thin wrappers") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20211208083423.22037-2-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This code has two bugs:
1) "cnt" is 255 but the size of the buffer is 256 so the last byte is
not used.
2) If we try to print more than 255 characters then "cnt" will be
negative and that will trigger a WARN() in snprintf(). The fix for
this is to use scnprintf() instead of snprintf().
We can re-write this code to be cleaner:
1) Rename "offset" to "off" because that's shorter.
2) Get rid of the "cnt" variable and just use "size - off" directly.
3) Get rid of the "read" variable and just increment "off" directly.
Fixes: 96fe6a2109db ("fbdev: Add VESA Coordinated Video Timings (CVT) support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If fb_alloc_cmap() fails in ufx_usb_probe(), fb_destroy_modelist() will
be called to destroy modelist in the error handling path. But modelist
has not been initialized yet, so it will result in null-ptr-deref.
Initialize modelist before calling fb_alloc_cmap() to fix this bug.
Fixes: 3c8a63e22a08 ("Add support for SMSC UFX6000/7000 USB display adapters") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In file included from ./arch/powerpc/include/asm/pgtable.h:20:0,
from ./include/linux/pgtable.h:6,
from ./include/linux/mm.h:33,
from drivers/video/fbdev/controlfb.c:37:
./arch/powerpc/include/asm/nohash/pgtable.h:243:0: note: this is the location of the previous definition
#define pgprot_cached_wthru(prot) (__pgprot((pgprot_val(prot) & ~_PAGE_CACHE_CTL) | \
The controlfb driver has a number of dummy defines for IO operations.
They were introduced in commit a07a63b0e24d
("video: fbdev: controlfb: add COMPILE_TEST support").
The write variants did not use their value parameter in the
dummy versions, resulting in set but not used warnings.
Fix this by adding "(void)val" to silence the compiler.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Link: https://patchwork.freedesktop.org/patch/msgid/20201206190247.1861316-13-sam@ravnborg.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Start from commit 11be60bd66d54 "matroxfb: add Matrox MGA-G200eW board
support", when maxvram is 0x800000, monitor become black w/ error message
said: "The current input timing is not supported by the monitor display.
Please change your input timing to 1920x1080@60Hz ...".
Fixes: 11be60bd66d5 ("matroxfb: add Matrox MGA-G200eW board support") Signed-off-by: Z. Liu <liuzx@knownsec.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Hantro H1 hardware can crop off pixels from the right and bottom of
the source frame. These are controlled with the H1_REG_IN_IMG_CTRL_OVRFLB
and H1_REG_IN_IMG_CTRL_OVRFLR in the H1_REG_IN_IMG_CTRL register.
The ChromeOS kernel driver that this was based on incorrectly added the
_D4 suffix H1_REG_IN_IMG_CTRL_OVRFLB. This field crops the bottom of the
input frame, and the number is _not_ divided by 4. [1]
Correct the name to avoid confusion when crop support with the selection
API is added.
As the possible failure of the kzalloc(), the 'new_ts' could be NULL
pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, the caller esparser_queue() needs to deal with the return value of
the amvdec_add_ts().
Fixes: 876f123b8956 ("media: meson: vdec: bring up to compliance") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Fixes: e7f3c5481035 ("[media] coda: use VDOA for un-tiling custom macroblock format") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver did not set the MM2S Fs Multiplier Register to the proper
value for playback streams. This needs to be set to the sample rate to
MCLK multiplier, or random stream underflows can occur on the downstream
I2S transmitter.
Store the sysclk value provided via the set_sysclk callback and use that
in conjunction with the sample rate in the hw_params callback to calculate
the proper value to set for this register.
Fixes: 6f6c3c36f091 ("ASoC: xlnx: add pcm formatter platform driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220120195832.1742271-2-robert.hancock@calian.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2161536516ed ("media: media/pci: set device_caps in struct video_device")
introduced a regression: V4L2_CAP_TUNER is always present in device_caps,
even when the device has no tuner.
This causes a warning:
WARNING: CPU: 0 PID: 249 at drivers/media/v4l2-core/v4l2-ioctl.c:1102 v4l_querycap+0xa0/0xb0 [videodev]
Fixes: 2161536516ed ("media: media/pci: set device_caps in struct video_device") Signed-off-by: Ondrej Zary <linux@zary.sk> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DST_QUEUE_OFF_BASE is applied to offset/mem_offset on MMAP capture buffers
only for the VIDIOC_QUERYBUF ioctl, while the userspace fields (including
offset/mem_offset) are filled in for VIDIOC_{QUERY,PREPARE,Q,DQ}BUF
ioctls. This leads to differences in the values presented to userspace.
If userspace attempts to mmap the capture buffer directly using values
from DQBUF, it will fail.
Move the code that applies the magic offset into a helper, and call
that helper from all four ioctl entry points.
[hverkuil: drop unnecessary '= 0' in v4l2_m2m_querybuf() for ret]
Fixes: 7f98639def42 ("V4L/DVB: add memory-to-memory device helper framework for videobuf") Fixes: 908a0d7c588e ("[media] v4l: mem2mem: port to videobuf2") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
vb2_dma_contig_set_max_seg_size need to have a size in parameter and not
a DMA_BIT_MASK().
While fixing this issue, also fix error handling of all DMA size
setting.
Reported-by: kernel test robot <lkp@intel.com> Fixes: d4ae3689226e5 ("media: zoran: device support only 32bit DMA address") Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function kunit_test_timeout, it is declared "300 * MSEC_PER_SEC"
represent 5min. However, it is wrong when dealing with arm64 whose
default HZ = 250, or some other situations. Use msecs_to_jiffies to fix
this, and kunit_test_timeout will work as desired.
Link: https://lkml.kernel.org/r/20220309083753.1561921-3-liupeng256@huawei.com Fixes: 5f3e06208920 ("kunit: test: add support for test abort") Signed-off-by: Peng Liu <liupeng256@huawei.com> Reviewed-by: Marco Elver <elver@google.com> Reviewed-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Tested-by: Brendan Higgins <brendanhiggins@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Wang Kefeng <wangkefeng.wang@huawei.com> Cc: David Gow <davidgow@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The $(CC) variable used in Makefiles could contain several arguments
such as "ccache gcc". These need to be passed as a single string to
check_cc.sh, otherwise only the first argument will be used as the
compiler command. Without quotes, the $(CC) variable is passed as
distinct arguments which causes the script to fail to build trivial
programs.
Fix this by adding quotes around $(CC) when calling check_cc.sh to pass
the whole string as a single argument to the script even if it has
several words such as "ccache gcc".
When compressed file has blocks, f2fs_ioc_start_atomic_write will succeed,
but compressed flag will be remained in inode. If write partial compreseed
cluster and commit atomic write will cause data corruption.
This is the reproduction process:
Step 1:
create a compressed file ,write 64K data , call fsync(), then the blocks
are write as compressed cluster.
Step2:
iotcl(F2FS_IOC_START_ATOMIC_WRITE) --- this should be fail, but not.
write page 0 and page 3.
iotcl(F2FS_IOC_COMMIT_ATOMIC_WRITE) -- page 0 and 3 write as normal file,
Step3:
drop cache.
read page 0-4 -- Since page 0 has a valid block address, read as
non-compressed cluster, page 1 and 2 will be filled with compressed data
or zero.
The root cause is, after commit 7eab7a696827 ("f2fs: compress: remove
unneeded read when rewrite whole cluster"), in step 2, f2fs_write_begin()
only set target page dirty, and in f2fs_commit_inmem_pages(), we will write
partial raw pages into compressed cluster, result in corrupting compressed
cluster layout.
Fixes: 4c8ff7095bef ("f2fs: support data compression") Fixes: 7eab7a696827 ("f2fs: compress: remove unneeded read when rewrite whole cluster") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Fengnan Chang <changfengnan@vivo.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
when we overwrite the whole page in cluster, we don't need read original
data before write, because after write_end(), writepages() can help to
load left data in that cluster.
When reflinking an inline extent, we assert that its file offset is 0 and
that its uncompressed length is not greater than the sector size. We then
return an error if one of those conditions is not satisfied. However we
use a return statement, which results in returning from btrfs_clone()
without freeing the path and buffer that were allocated before, as well as
not clearing the flag BTRFS_INODE_NO_DELALLOC_FLUSH for the destination
inode.
Fix that by jumping to the 'out' label instead, and also add a WARN_ON()
for each condition so that in case assertions are disabled, we get to
known which of the unexpected conditions triggered the error.
Fixes: a61e1e0df9f321 ("Btrfs: simplify inline extent handling when doing reflinks") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Quoted from Jing Xia's report, there is a potential deadlock may happen
between kworker and checkpoint as below:
[T:writeback] [T:checkpoint]
- wb_writeback
- blk_start_plug
bio contains NodeA was plugged in writeback threads
- do_writepages -- sync write inodeB, inc wb_sync_req[DATA]
- f2fs_write_data_pages
- f2fs_write_single_data_page -- write last dirty page
- f2fs_do_write_data_page
- set_page_writeback -- clear page dirty flag and
PAGECACHE_TAG_DIRTY tag in radix tree
- f2fs_outplace_write_data
- f2fs_update_data_blkaddr
- f2fs_wait_on_page_writeback -- wait NodeA to writeback here
- inode_dec_dirty_pages
- writeback_sb_inodes
- writeback_single_inode
- do_writepages
- f2fs_write_data_pages -- skip writepages due to wb_sync_req[DATA]
- wbc->pages_skipped += get_dirty_pages() -- PAGECACHE_TAG_DIRTY is not set but get_dirty_pages() returns one
- requeue_inode -- requeue inode to wb->b_dirty queue due to non-zero.pages_skipped
- blk_finish_plug
Let's try to avoid deadlock condition by forcing unplugging previous bio via
blk_finish_plug(current->plug) once we'v skipped writeback in writepages()
due to valid sbi->wb_sync_req[DATA/NODE].
Fixes: 687de7f1010c ("f2fs: avoid IO split due to mixed WB_SYNC_ALL and WB_SYNC_NONE") Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Signed-off-by: Jing Xia <jing.xia@unisoc.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nfsd file cache table can be pretty large and its allocation
may require as many as 80 contigious pages.
Employ the same fix that was employed for similar issue that was
reported for the reply cache hash table allocation several years ago
by commit 8f97514b423a ("nfsd: more robust allocation failure handling
in nfsd_reply_cache_init").
Fixes: 65294c1f2c5e ("nfsd: add a new struct file caching facility to nfsd") Link: https://lore.kernel.org/linux-nfs/e3cdaeec85a6cfec980e87fc294327c0381c1778.camel@kernel.org/ Suggested-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change from shifting 'unsigned long' to 'u64' to prevent the config bits
being lost on a 32-bit kernel.
Fixes: eadf48cab4b6b0 ("perf/x86/intel/pt: Add support for address range filtering in PT") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20220131072453.2839535-5-adrian.hunter@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The rseq rseq_cs.ptr.{ptr32,padding} uapi endianness handling is
entirely wrong on 32-bit little endian: a preprocessor logic mistake
wrongly uses the big endian field layout on 32-bit little endian
architectures.
Fortunately, those ptr32 accessors were never used within the kernel,
and only meant as a convenience for user-space.
Remove those and replace the whole rseq_cs union by a __u64 type, as
this is the only thing really needed to express the ABI. Document how
32-bit architectures are meant to interact with this field.
Fixes: ec9c82e03a74 ("rseq: uapi: Declare rseq_cs field as union, update includes") Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20220127152720.25898-1-mathieu.desnoyers@efficios.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The older format of /proc/pid/sched printed home node info which
required the mempolicy and task lock around mpol_get(). However
the format has changed since then and there is no need for
sched_show_numa() any more to have mempolicy argument,
asssociated mpol_get/put and task_lock/unlock. Remove them.
Fixes: 397f2378f1361 ("sched/numa: Fix numa balancing stats in /proc/pid/sched") Signed-off-by: Bharata B Rao <bharata@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Mel Gorman <mgorman@suse.de> Link: https://lore.kernel.org/r/20220118050515.2973-1-bharata@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log