The QDMA packet scheduler suffers from a performance issue.
Fix this by picking up changes from MediaTek's SDK which change to use
Token Bucket instead of Leaky Bucket and fix the SPEED_1000 configuration.
net: ethernet: mtk_eth_soc: reapply mdc divider on reset
In the current method, the MDC divider was reset to the default setting
of 2.5MHz after the NETSYS SER. Therefore, we need to reapply the MDC
divider configuration function in mtk_hw_init() after reset.
Paolo Abeni [Thu, 17 Apr 2025 13:20:41 +0000 (15:20 +0200)]
Merge tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following batch contains one Netfilter fix for net:
1) conntrack offload bit is erroneously unset in a race scenario,
from Florian Westphal.
netfilter pull request 25-04-17
* tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: fix erronous removal of offload bit
====================
Paolo Abeni [Thu, 17 Apr 2025 11:08:41 +0000 (13:08 +0200)]
Merge tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- l2cap: Process valid commands in too long frame
- vhci: Avoid needless snprintf() calls
* tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: vhci: Avoid needless snprintf() calls
Bluetooth: l2cap: Process valid commands in too long frame
====================
====================
Bug fixes from XDP and perout series
This patch series consists of bug fixes from the XDP series:
1. Fixes a kernel warning that occurs when bringing down the
network interface.
2. Resolves a potential NULL pointer dereference in the
emac_xmit_xdp_frame() function.
3. Resolves a potential NULL pointer dereference in the
icss_iep_perout_enable() function
net: ti: icss-iep: Fix possible NULL pointer dereference for perout request
The ICSS IEP driver tracks perout and pps enable state with flags.
Currently when disabling pps and perout signals during icss_iep_exit(),
results in NULL pointer dereference for perout.
To fix the null pointer dereference issue, the icss_iep_perout_enable_hw
function can be modified to directly clear the IEP CMP registers when
disabling PPS or PEROUT, without referencing the ptp_perout_request
structure, as its contents are irrelevant in this case.
Fixes: 9b115361248d ("net: ti: icssg-prueth: Fix clearing of IEP_CMP_CFG registers during iep_init") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/7b1c7c36-363a-4085-b26c-4f210bee1df6@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-4-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix possible NULL pointer dereference inside emac_xmit_xdp_frame()
There is an error check inside emac_xmit_xdp_frame() function which
is called when the driver wants to transmit XDP frame, to check if
the allocated tx descriptor is NULL, if true to exit and return
ICSSG_XDP_CONSUMED implying failure in transmission.
In this case trying to free a descriptor which is NULL will result
in kernel crash due to NULL pointer dereference. Fix this error handling
and increase netdev tx_dropped stats in the caller of this function
if the function returns ICSSG_XDP_CONSUMED.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/70d8dd76-0c76-42fc-8611-9884937c82f5@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-3-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix kernel warning while bringing down network interface
During network interface initialization, the NIC driver needs to register
its Rx queue with the XDP, to ensure the incoming XDP buffer carries a
pointer reference to this info and is stored inside xdp_rxq_info.
While this struct isn't tied to XDP prog, if there are any changes in
Rx queue, the NIC driver needs to stop the Rx queue by unregistering
with XDP before purging and reallocating memory. Drop page_pool destroy
during Rx channel reset as this is already handled by XDP during
xdp_rxq_info_unreg (Rx queue unregister), failing to do will cause the
following warning:
Fixes: 46eeb90f03e0 ("net: ti: icssg-prueth: Use page_pool API for RX buffer allocation") Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-2-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
netfilter: conntrack: fix erronous removal of offload bit
The blamed commit exposes a possible issue with flow_offload_teardown():
We might remove the offload bit of a conntrack entry that has been
offloaded again.
1. conntrack entry c1 is offloaded via flow f1 (f1->ct == c1).
2. f1 times out and is pushed back to slowpath, c1 offload bit is
removed. Due to bug, f1 is not unlinked from rhashtable right away.
3. a new packet arrives for the flow and re-offload is triggered, i.e.
f2->ct == c1. This is because lookup in flowtable skip entries with
teardown bit set.
4. Next flowtable gc cycle finds f1 again
5. flow_offload_teardown() is called again for f1 and c1 offload bit is
removed again, even though we have f2 referencing the same entry.
This is harmless, but clearly not correct.
Fix the bug that exposes this: set 'teardown = true' to have the gc
callback unlink the flowtable entry from the table right away instead of
the unintentional defer to the next round.
Also prevent flow_offload_teardown() from fixing up the ct state more than
once: We could also be called from the data path or a notifier, not only
from the flowtable gc callback.
NF_FLOW_TEARDOWN can never be unset, so we can use it as synchronization
point: if we observe did not see a 0 -> 1 transition, then another CPU
is already doing the ct state fixups for us.
Jakub Kicinski [Tue, 15 Apr 2025 15:15:52 +0000 (08:15 -0700)]
net: don't try to ops lock uninitialized devs
We need to be careful when operating on dev while in rtnl_create_link().
Some devices (vxlan) initialize netdev_ops in ->newlink, so later on.
Avoid using netdev_lock_ops(), the device isn't registered so we
cannot legally call its ops or generate any notifications for it.
netdev_ops_assert_locked_or_invisible() is safe to use, it checks
registration status first.
Reported-by: syzbot+de1c7d68a10e3f123bdd@syzkaller.appspotmail.com Fixes: 04efcee6ef8d ("net: hold instance lock during NETDEV_CHANGE") Acked-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20250415151552.768373-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ptp: ocp: fix start time alignment in ptp_ocp_signal_set
In ptp_ocp_signal_set, the start time for periodic signals is not
aligned to the next period boundary. The current code rounds up the
start time and divides by the period but fails to multiply back by
the period, causing misaligned signal starts. Fix this by multiplying
the rounded-up value by the period to ensure the start time is the
closest next period.
Fixes: 4bd46bb037f8e ("ptp: ocp: Use DIV64_U64_ROUND_UP for rounding.") Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250415053131.129413-1-maimon.sagi@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 17 Apr 2025 01:14:45 +0000 (18:14 -0700)]
Merge branch 'collection-of-dsa-bug-fixes'
Vladimir Oltean says:
====================
Collection of DSA bug fixes
Prompted by Russell King's 3 DSA bug reports from Friday (linked in
their respective patches: 1, 2 and 3), I am providing fixes to those, as
well as flushing the queue with 2 other bug fixes I had.
1: fix NULL pointer dereference during mv88e6xxx driver unbind, on old
switch models which lack PVT and/or STU. Seen on the ZII dev board
rev B.
2: fix failure to delete bridge port VLANs on old mv88e6xxx chips which
lack STU. Seen on the same board.
3: fix WARN_ON() and resource leak in DSA core on driver unbind. Seen on
the same board but is a much more widespread issue.
4: fix use-after-free during probing of DSA trees with >= 3 switches,
if -EPROBE_DEFER exists. In principle issue also exists for the ZII
board, I reproduced on Turris MOX.
5: fix incorrect use of refcount API in DSA core for those switches
which use tag_8021q (felix, sja1105, vsc73xx). Returning an error
when attempting to delete a tag_8021q VLAN prints a WARN_ON(), which
is harmless but might be problematic with CONFIG_PANIC_ON_OOPS.
====================
Vladimir Oltean [Mon, 14 Apr 2025 21:30:20 +0000 (00:30 +0300)]
net: dsa: avoid refcount warnings when ds->ops->tag_8021q_vlan_del() fails
This is very similar to the problem and solution from commit 232deb3f9567 ("net: dsa: avoid refcount warnings when
->port_{fdb,mdb}_del returns error"), except for the
dsa_port_do_tag_8021q_vlan_del() operation.
Vladimir Oltean [Mon, 14 Apr 2025 21:30:01 +0000 (00:30 +0300)]
net: dsa: free routing table on probe failure
If complete = true in dsa_tree_setup(), it means that we are the last
switch of the tree which is successfully probing, and we should be
setting up all switches from our probe path.
After "complete" becomes true, dsa_tree_setup_cpu_ports() or any
subsequent function may fail. If that happens, the entire tree setup is
in limbo: the first N-1 switches have successfully finished probing
(doing nothing but having allocated persistent memory in the tree's
dst->ports, and maybe dst->rtable), and switch N failed to probe, ending
the tree setup process before anything is tangible from the user's PoV.
If switch N fails to probe, its memory (ports) will be freed and removed
from dst->ports. However, the dst->rtable elements pointing to its ports,
as created by dsa_link_touch(), will remain there, and will lead to
use-after-free if dereferenced.
If dsa_tree_setup_switches() returns -EPROBE_DEFER, which is entirely
possible because that is where ds->ops->setup() is, we get a kasan
report like this:
==================================================================
BUG: KASAN: slab-use-after-free in mv88e6xxx_setup_upstream_port+0x240/0x568
Read of size 8 at addr ffff000004f56020 by task kworker/u8:3/42
The simplest way to fix the bug is to delete the routing table in its
entirety. dsa_tree_setup_routing_table() has no problem in regenerating
it even if we deleted links between ports other than those of switch N,
because dsa_link_touch() first checks whether the port pair already
exists in dst->rtable, allocating if not.
The deletion of the routing table in its entirety already exists in
dsa_tree_teardown(), so refactor that into a function that can also be
called from the tree setup error path.
In my analysis of the commit to blame, it is the one which added
dsa_link elements to dst->rtable. Prior to that, each switch had its own
ds->rtable which is freed when the switch fails to probe. But the tree
is potentially persistent memory.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:30 +0000 (00:29 +0300)]
net: dsa: clean up FDB, MDB, VLAN entries on unbind
As explained in many places such as commit b117e1e8a86d ("net: dsa:
delete dsa_legacy_fdb_add and dsa_legacy_fdb_del"), DSA is written given
the assumption that higher layers have balanced additions/deletions.
As such, it only makes sense to be extremely vocal when those
assumptions are violated and the driver unbinds with entries still
present.
But Ido Schimmel points out a very simple situation where that is wrong:
https://lore.kernel.org/netdev/ZDazSM5UsPPjQuKr@shredder/
(also briefly discussed by me in the aforementioned commit).
Basically, while the bridge bypass operations are not something that DSA
explicitly documents, and for the majority of DSA drivers this API
simply causes them to go to promiscuous mode, that isn't the case for
all drivers. Some have the necessary requirements for bridge bypass
operations to do something useful - see dsa_switch_supports_uc_filtering().
Although in tools/testing/selftests/net/forwarding/local_termination.sh,
we made an effort to popularize better mechanisms to manage address
filters on DSA interfaces from user space - namely macvlan for unicast,
and setsockopt(IP_ADD_MEMBERSHIP) - through mtools - for multicast, the
fact is that 'bridge fdb add ... self static local' also exists as
kernel UAPI, and might be useful to someone, even if only for a quick
hack.
It seems counter-productive to block that path by implementing shim
.ndo_fdb_add and .ndo_fdb_del operations which just return -EOPNOTSUPP
in order to prevent the ndo_dflt_fdb_add() and ndo_dflt_fdb_del() from
running, although we could do that.
Accepting that cleanup is necessary seems to be the only option.
Especially since we appear to be coming back at this from a different
angle as well. Russell King is noticing that the WARN_ON() triggers even
for VLANs:
https://lore.kernel.org/netdev/Z_li8Bj8bD4-BYKQ@shell.armlinux.org.uk/
What happens in the bug report above is that dsa_port_do_vlan_del() fails,
then the VLAN entry lingers on, and then we warn on unbind and leak it.
This is not a straight revert of the blamed commit, but we now add an
informational print to the kernel log (to still have a way to see
that bugs exist), and some extra comments gathered from past years'
experience, to justify the logic.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:13 +0000 (00:29 +0300)]
net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported
Russell King reports that on the ZII dev rev B, deleting a bridge VLAN
from a user port fails with -ENOENT:
https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/
This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(),
which tries to find an MST entry in &chip->msts associated with the SID,
but fails and returns -ENOENT as such.
But we know that this chip does not support MST at all, so that is not
surprising. The question is why does the guard in mv88e6xxx_mst_put()
not exit early:
if (!sid)
return 0;
And the answer seems to be simple: the sid comes from vlan.sid which
supposedly was previously populated by mv88e6xxx_vtu_get().
But some chip->info->ops->vtu_getnext() implementations do not populate
vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case,
later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is
just residual stack memory.
Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge
VLAN mapped to the default MSTI. For some chips, SID 0 is valid and
installed by mv88e6xxx_stu_setup(). A chip which does not support the
STU would implicitly only support mapping all VLANs to the default MSTI,
so although SID 0 is not valid, it would be sufficient, if we were to
zero-initialize the vlan structure, to fix the bug, due to the
coincidence that a test for vlan.sid == 0 already exists and leads to
the same (correct) behavior.
Another option which would be sufficient would be to add a test for
mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one
which already exists in mv88e6xxx_mst_get(). But that placement means
the caller will have to dereference vlan.sid, which means it will access
uninitialized memory, which is not nice even if it ignores it later.
So we end up making both modifications, in order to not rely just on the
sid == 0 coincidence, but also to avoid having uninitialized structure
fields which might get temporarily accessed.
Vladimir Oltean [Mon, 14 Apr 2025 21:28:50 +0000 (00:28 +0300)]
net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered
Russell King reports that a system with mv88e6xxx dereferences a NULL
pointer when unbinding this driver:
https://lore.kernel.org/netdev/Z_lRkMlTJ1KQ0kVX@shell.armlinux.org.uk/
The crash seems to be in devlink_region_destroy(), which is not NULL
tolerant but is given a NULL devlink global region pointer.
At least on some chips, some devlink regions are conditionally registered
since the blamed commit, see mv88e6xxx_setup_devlink_regions_global():
if (cond && !cond(chip))
continue;
These are MV88E6XXX_REGION_STU and MV88E6XXX_REGION_PVT. If the chip
does not have an STU or PVT, it should crash like this.
To fix the issue, avoid unregistering those regions which are NULL, i.e.
were skipped at mv88e6xxx_setup_devlink_regions_global() time.
Fixes: 836021a2d0e0 ("net: dsa: mv88e6xxx: Export cross-chip PVT as devlink region") Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250414212850.2953957-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: txgbe: fix memory leak in txgbe_probe() error path
When txgbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in txgbe_probe() function, the subsequent
error paths after txgbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when txgbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Jonas Gorski [Mon, 14 Apr 2025 20:00:20 +0000 (22:00 +0200)]
net: bridge: switchdev: do not notify new brentries as changed
When adding a bridge vlan that is pvid or untagged after the vlan has
already been added to any other switchdev backed port, the vlan change
will be propagated as changed, since the flags change.
This causes the vlan to not be added to the hardware for DSA switches,
since the DSA handler ignores any vlans for the CPU or DSA ports that
are changed.
E.g. the following order of operations would work:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev swbridge vid 1 pvid untagged self
$ bridge vlan add dev lan1 vid 1 pvid untagged
but this order would break:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev lan1 vid 1 pvid untagged
$ bridge vlan add dev swbridge vid 1 pvid untagged self
Additionally, the vlan on the bridge itself would become undeletable:
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 PVID Egress Untagged
$ bridge vlan del dev swbridge vid 1 self
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 Egress Untagged
since the vlan was never added to DSA's vlan list, so deleting it will
cause an error, causing the bridge code to not remove it.
Fix this by checking if flags changed only for vlans that are already
brentry and pass changed as false for those that become brentries, as
these are a new vlan (member) from the switchdev point of view.
Since *changed is set to true for becomes_brentry = true regardless of
would_change's value, this will not change any rtnetlink notification
delivery, just the value passed on to switchdev in vlan->changed.
Fixes: 8d23a54f5bee ("net: bridge: switchdev: differentiate new VLANs from changed ones") Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250414200020.192715-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Mon, 14 Apr 2025 20:04:34 +0000 (22:04 +0200)]
net: b53: enable BPDU reception for management port
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
====================
ynl: avoid leaks in attr override and spec fixes for C
The C rt-link work revealed more problems in existing codegen
and classic netlink specs.
Patches 1 - 4 fix issues with the codegen. Patches 1 and 2 are
pre-requisites for patch 3. Patch 3 fixes leaking memory if user
tries to override already set attr. Patch 4 validates attrs in case
kernel sends something we don't expect.
Remaining patches fix and align the specs. Patch 5 changes nesting,
the rest are naming adjustments.
====================
Jakub Kicinski [Mon, 14 Apr 2025 21:18:51 +0000 (14:18 -0700)]
netlink: specs: rt-neigh: prefix struct nfmsg members with ndm
Attach ndm- to all members of struct nfmsg. We could possibly
use name-prefix just for C, but I don't think we have any precedent
for using name-prefix on structs, and other rtnetlink sub-specs
give full names for fixed header struct members.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-9-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCTP attribute naming is inconsistent. In C we have:
IFLA_MCTP_NET,
IFLA_MCTP_PHYS_BINDING,
^^^^
but in YAML:
- mctp-net
- phys-binding
^
no "mctp"
It's unclear whether the "mctp" part of the name is supposed
to be a prefix or part of attribute name. Make it a prefix,
seems cleaner, even tho technically phys-binding was added later.
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-8-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some attribute names diverge in very minor ways from the C names.
These are most likely typos, and they prevent the C codegen from
working.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-7-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:48 +0000 (14:18 -0700)]
netlink: specs: rt-link: add an attr layer around alt-ifname
alt-ifname attr is directly placed in requests (as an alternative
to ifname) but in responses its wrapped up in IFLA_PROP_LIST
and only there is may be multi-attr. See rtnl_fill_prop_list().
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:47 +0000 (14:18 -0700)]
tools: ynl-gen: make sure we validate subtype of array-nest
ArrayNest AKA indexed-array support currently skips inner type
validation. We count the attributes and then we parse them,
make sure we call validate, too. Otherwise buggy / unexpected
kernel response may lead to crashes.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-5-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:46 +0000 (14:18 -0700)]
tools: ynl-gen: individually free previous values on double set
When user calls request_attrA_set() multiple times (for the same
attribute), and attrA is of type which allocates memory -
we try to free the previously associated values. For array
types (including multi-attr) we have only freed the array,
but the array may have contained pointers.
Refactor the code generation for free attr and reuse the generated
lines in setters to flush out the previous state. Since setters
are static inlines in the header we need to add forward declarations
for the free helpers of pure nested structs. Track which types get
used by arrays and include the right forwad declarations.
At least ethtool string set and bit set would not be freed without
this. Tho, admittedly, overriding already set attribute twice is likely
a very very rare thing to do.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-4-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:45 +0000 (14:18 -0700)]
tools: ynl-gen: move local vars after the opening bracket
The "function writing helper" tries to put local variables
between prototype and the opening bracket. Clearly wrong,
but up until now nothing actually uses it to write local
vars so it wasn't noticed.
Jakub Kicinski [Mon, 14 Apr 2025 21:18:44 +0000 (14:18 -0700)]
tools: ynl-gen: don't declare loop iterator in place
The codegen tries to follow the "old" C style and declare loop
iterators at the start of the block / function. Only nested
request handling breaks this style, so adjust it.
cxgb4: fix memory leak in cxgb4_init_ethtool_filters() error path
In the for loop used to allocate the loc_array and bmap for each port, a
memory leak is possible when the allocation for loc_array succeeds,
but the allocation for bmap fails. This is because when the control flow
goes to the label free_eth_finfo, only the allocations starting from
(i-1)th iteration are freed.
Fix that by freeing the loc_array in the bmap allocation error path.
Fixes: d915c299f1da ("cxgb4: add skeleton for ethtool n-tuple filters") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414170649.89156-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid double-copying of string literals. Use a "const char *" for each
string instead of copying from .rodata into stack and then into the skb.
We can go directly from .rodata to the skb.
This also works around a Clang bug (that has since been fixed[1]).
Bluetooth: l2cap: Process valid commands in too long frame
This is required for passing PTS test cases:
- L2CAP/COS/CED/BI-14-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Connection Request
- L2CAP/COS/CED/BI-15-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Disconnection Request
The test procedure defined in L2CAP.TS.p39 for both tests is:
1. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 8 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains one L2CAP_ECHO_REQ
packet with Data Length set to 0 with 0 octets of echo data and
one command packet and Data Length set as specified in Table 4.6
and the correct command data.
2. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
3. Perform alternative 3A, 3B, 3C, or 3D depending on the IUTâs
response.
Alternative 3A (IUT terminates the link):
3A.1 The IUT terminates the link.
3A.2 The test ends with a Pass verdict.
Alternative 3B (IUT discards the frame):
3B.1 The IUT does not send a reply to the Lower Tester.
Alternative 3C (IUT rejects PDU):
3C.1 The IUT sends an L2CAP_COMMAND_REJECT_RSP PDU to the
Lower Tester.
Alternative 3D (Any other IUT response):
3D.1 The Upper Tester issues a warning and the test ends.
4. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 4 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains Data Length set to
0 with an L2CAP_ECHO_REQ packet with 0 octets of echo data.
5. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
With expected outcome:
In Steps 2 and 5, the IUT responds with an L2CAP_ECHO_RSP.
In Step 3A.1, the IUT terminates the link.
In Step 3B.1, the IUT does not send a reply to the Lower Tester.
In Step 3C.1, the IUT rejects the PDU.
In Step 3D.1, the IUT sends any valid response.
Currently PTS fails with the following logs:
Failed to receive ECHO RESPONSE.
And HCI logs:
> ACL Data RX: Handle 11 flags 0x02 dlen 20
L2CAP: Information Response (0x0b) ident 2 len 12
Type: Fixed channels supported (0x0003)
Result: Success (0x0000)
Channels: 0x000000000000002e
L2CAP Signaling (BR/EDR)
Connectionless reception
AMP Manager Protocol
L2CAP Signaling (LE)
> ACL Data RX: Handle 11 flags 0x02 dlen 13
frame too long
08 01 00 00 08 02 01 00 aa .........
Cc: stable@vger.kernel.org Signed-off-by: FrĂŠdĂŠric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sven Eckelmann [Mon, 14 Apr 2025 18:05:37 +0000 (20:05 +0200)]
batman-adv: Fix double-hold of meshif when getting enabled
It was originally meant to replace the dev_hold with netdev_hold. But this
was missed in batadv_hardif_enable_interface(). As result, there was an
imbalance and a hang when trying to remove the mesh-interface with
(previously) active hard-interfaces:
unregister_netdevice: waiting for batadv0 to become free. Usage count = 3
Fixes: 00b35530811f ("batman-adv: adopt netdev_hold() / netdev_put()") Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+ff3aa851d46ab82953a3@syzkaller.appspotmail.com Reported-by: syzbot+4036165fc595a74b09b2@syzkaller.appspotmail.com Reported-by: syzbot+c35d73ce910d86c0026e@syzkaller.appspotmail.com Reported-by: syzbot+48c14f61594bdfadb086@syzkaller.appspotmail.com Reported-by: syzbot+f37372d86207b3bb2941@syzkaller.appspotmail.com Signed-off-by: Sven Eckelmann <sven@narfation.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250414-double_hold_fix-v5-1-10e056324cde@narfation.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 40867d74c374 ("net: Add l3mdev index to flow struct and
avoid oif reset for port devices") it was possible to use FIB rules to
match on a L3 domain. This was done by having a FIB rule match on iif /
oif being a L3 master device. It worked because prior to the FIB rule
lookup the iif / oif fields in the flow structure were reset to the
index of the L3 master device to which the input / output device was
enslaved to.
The above scheme made it impossible to match on the original input /
output device. Therefore, cited commit stopped overwriting the iif / oif
fields in the flow structure and instead stored the index of the
enslaving L3 master device in a new field ('flowi_l3mdev') in the flow
structure.
While the change enabled new use cases, it broke the original use case
of matching on a L3 domain. Fix this by interpreting the iif / oif
matching on a L3 master device as a match against the L3 domain. In
other words, if the iif / oif in the FIB rule points to a L3 master
device, compare the provided index against 'flowi_l3mdev' rather than
'flowi_{i,o}if'.
Before cited commit, a FIB rule that matched on 'iif vrf1' would only
match incoming traffic from devices enslaved to 'vrf1'. With the
proposed change (i.e., comparing against 'flowi_l3mdev'), the rule would
also match traffic originating from a socket bound to 'vrf1'. Avoid that
by adding a new flow flag ('FLOWI_FLAG_L3MDEV_OIF') that indicates if
the L3 domain was derived from the output interface or the input
interface (when not set) and take this flag into account when evaluating
the FIB rule against the flow structure.
Avoid unnecessary checks in the data path by detecting that a rule
matches on a L3 master device when the rule is installed and marking it
as such.
ip route add table 100 default dev dummy1
ip route add table 200 default dev dummy1
ip route add table 300 default dev dummy1
ip rule add prio 0 oif vrf1 table 100
ip rule add prio 1 iif vrf1 table 200
ip rule add prio 2 table 300
ip route get 192.0.2.1 oif dummy1 fibmatch
ip route get 192.0.2.1 iif dummy1 from 198.51.100.1 fibmatch
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: hanhuihui <hanhuihui5@huawei.com> Closes: https://lore.kernel.org/netdev/ec671c4f821a4d63904d0da15d604b75@huawei.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250414172022.242991-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 14:32:10 +0000 (07:32 -0700)]
eth: bnxt: fix missing ring index trim on error path
Commit under Fixes converted tx_prod to be free running but missed
masking it on the Tx error path. This crashes on error conditions,
for example when DMA mapping fails.
A reference to the device tree node is stored in a private struct, thus
the reference count has to be incremented. Also, decrement the count on
device removal and in the error path.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Michael Walle <mwalle@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250414083942.4015060-1-mwalle@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: ngbe: fix memory leak in ngbe_probe() error path
When ngbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in ngbe_probe() function, the subsequent
error paths after ngbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when ngbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 02338c484ab6 ("net: ngbe: Initialize sw info and register netdev") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com> Link: https://patch.msgid.link/20250412154927.25908-1-abdun.nihaal@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Mon, 14 Apr 2025 22:58:30 +0000 (15:58 -0700)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
igc: Fix PTM timeout
Christopher S M Hall says:
There have been sporadic reports of PTM timeouts using i225/i226 devices
These timeouts have been root caused to:
1) Manipulating the PTM status register while PTM is enabled
and triggered
2) The hardware retrying too quickly when an inappropriate response
is received from the upstream device
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
The first patch in this series also resolves an issue reported by Corinna
Vinschen relating to kdump:
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not zero, but extremly reduced.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: add lock preventing multiple simultaneous PTM transactions
igc: cleanup PTP module if probe fails
igc: handle the IGC_PTP_ENABLED flag correctly
igc: move ktime snapshot into PTM retry loop
igc: increase wait time before retrying PTM
igc: fix PTM cycle trigger logic
====================
Jakub Kicinski [Wed, 9 Apr 2025 14:55:41 +0000 (07:55 -0700)]
netlink: specs: ovs_vport: align with C codegen capabilities
We started generating C code for OvS a while back, but actually
C codegen only supports fixed headers specified at the family
level right now (schema also allows specifying them per op).
ovs_flow and ovs_datapath already specify the fixed header
at the family level but ovs_vport does it per op.
Move the property, all ops use the same header.
The first dependency is the problem. wiphy mutex should be outside
the instance locks. The problem happens in notifiers (as always)
for CLOSE. We only hold the instance lock for ops locked devices
during CLOSE, and WiFi netdevs are not ops locked. Unfortunately,
when we dev_close_many() during netns dismantle we may be holding
the instance lock of _another_ netdev when issuing a CLOSE for
a WiFi device.
Lockdep's "Possible unsafe locking scenario" only prints 3 locks
and we have 4, plus I think we'd need 3 CPUs, like this:
Tho, I don't think that's possible as CPU1 and CPU2 would
be under rtnl_lock. Even if we have per-netns rtnl_lock and
wiphy can span network namespaces - CPU0 and CPU1 must be
in the same netns to see dev_instance_lock, so CPU0 can't
be installing a socket as CPU1 is tearing the netns down.
Regardless, our expected lock ordering is that wiphy lock
is taken before instance locks, so let's fix this.
Go over the ops locked and non-locked devices separately.
Note that calling dev_close_many() on an empty list is perfectly
fine. All processing (including RCU syncs) are conditional
on the list not being empty, already.
Fixes: 7e4d784f5810 ("net: hold netdev instance lock during rtnetlink operations") Reported-by: syzbot+6f588c78bf765b62b450@syzkaller.appspotmail.com Acked-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250412233011.309762-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After detecting the np_link_fail exception,
the driver attempts to fix the exception by
using phy_stop() and phy_start() in the scheduled task.
However, hbg_fix_np_link_fail() and .ndo_stop()
may be concurrently executed. As a result,
phy_stop() is executed twice, and the following Calltrace occurs:
This patch adds the rtnl_lock to hbg_fix_np_link_fail()
to ensure that other operations are not performed concurrently.
In addition, np_link_fail exception can be fixed
only when the PHY is link.
Fixes: e0306637e85d ("net: hibmcge: Add support for mac link exception handling feature") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-8-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: hibmcge: fix not restore rx pause mac addr after reset issue
The MAC hardware supports receiving two types of
pause frames from link partner.
One is a pause frame with a destination address
of 01:80:C2:00:00:01.
The other is a pause frame whose destination address
is the address of the hibmcge driver.
01:80:C2:00:00:01 is supported by default.
In .ndo_set_mac_address(), the hibmcge driver calls
.hbg_hw_set_rx_pause_mac_addr() to set its mac address as the
destination address of the rx puase frame.
Therefore, pause frames with two types of MAC addresses can be received.
Currently, the rx pause addr does not restored after reset.
As a result, pause frames whose destination address is
the hibmcge driver address cannot be correctly received.
This patch restores the configuration by calling
.hbg_hw_set_rx_pause_mac_addr() after reset is complete.
Fixes: 3f5a61f6d504 ("net: hibmcge: Add reset supported in this module") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-7-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: hibmcge: fix the incorrect np_link fail state issue.
In the debugfs file, the driver displays the np_link fail state
based on the HBG_NIC_STATE_NP_LINK_FAIL.
However, HBG_NIC_STATE_NP_LINK_FAIL is cleared in hbg_service_task()
So, this value of np_link fail is always false.
This patch directly reads the related register to display the real state.
Fixes: e0306637e85d ("net: hibmcge: Add support for mac link exception handling feature") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-6-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A dbg log is generated when the driver modifies the MTU,
which is expected to trace the change of the MTU.
However, the log is recorded after WRITE_ONCE().
At this time, netdev->mtu has been changed to the new value.
As a result, netdev->mtu is the same as new_mtu.
This patch modifies the log location and records logs before WRITE_ONCE().
Fixes: ff4edac6e9bd ("net: hibmcge: Implement some .ndo functions") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-5-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: hibmcge: fix the share of irq statistics among different network ports issue
hbg_irqs is a global array which contains irq statistics.
However, the irq statistics of different network ports
point to the same global array. As a result, the statistics are incorrect.
This patch allocates a statistics array for each network port
to prevent the statistics of different network ports
from affecting each other.
irq statistics are removed from hbg_irq_info. Therefore,
all data in hbg_irq_info remains unchanged. Therefore,
the input parameter of some functions is changed to const.
Fixes: 4d089035fa19 ("net: hibmcge: Add interrupt supported in this module") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-4-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver supports pause frames,
but does not pass pause frames based on rx pause enable configuration,
resulting in incorrect pause frame statistics.
ethtool --include-statistics -a enp132s0f2
Pause parameters for enp132s0f2:
Autonegotiate: on
RX: on
TX: on
RX negotiated: on
TX negotiated: on
Statistics:
tx_pause_frames: 0
rx_pause_frames: 100
Fixes: 3a03763f3876 ("net: hibmcge: Add pauseparam supported in this module") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250410021327.590362-2-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 04efcee6ef8d ("net: hold instance lock during NETDEV_CHANGE")
changed to lockless __linkwatch_sync_dev in ethtool_op_get_link.
All paths except bonding are coming via locked ioctl. Add necessary
locking to bonding.
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Reported-by: syzbot+48c14f61594bdfadb086@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=48c14f61594bdfadb086 Fixes: 04efcee6ef8d ("net: hold instance lock during NETDEV_CHANGE") Signed-off-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250410161117.3519250-1-sdf@fomichev.me Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool: cmis_cdb: use correct rpl size in ethtool_cmis_module_poll()
rpl is passed as a pointer to ethtool_cmis_module_poll(), so the correct
size of rpl is sizeof(*rpl) which should be just 1 byte. Using the
pointer size instead can cause stack corruption:
pds_core: fix memory leak in pdsc_debugfs_add_qcq()
The memory allocated for intr_ctrl_regset, which is passed to
debugfs_create_regset32() may not be cleaned up when the driver is
removed. Fix that by using device managed allocation for it.
Fixes: 45d76f492938 ("pds_core: set up device and adminq") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Link: https://patch.msgid.link/20250409054450.48606-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 11 Apr 2025 23:38:03 +0000 (16:38 -0700)]
Merge tag 'wireless-2025-04-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a handful of fixes, notably
- iwlwifi: various build warning fixes (e.g. PM_SLEEP)
- iwlwifi: fix operation when FW reset handshake times out
- mac80211: drop pending frames on interface down
* tag 'wireless-2025-04-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
Revert "wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()"
wifi: iwlwifi: mld: Restart firmware on iwl_mld_no_wowlan_resume() error
wifi: iwlwifi: pcie: set state to no-FW before reset handshake
wifi: wl1251: fix memory leak in wl1251_tx_work
wifi: brcmfmac: fix memory leak in brcmf_get_module_param
wifi: iwlwifi: mld: silence uninitialized variable warning
wifi: mac80211: Purge vif txq in ieee80211_do_stop()
wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()
wifi: at76c50x: fix use after free access in at76_disconnect
wifi: add wireless list to MAINTAINERS
iwlwifi: mld: fix building with CONFIG_PM_SLEEP disabled
wifi: iwlwifi: mld: fix PM_SLEEP -Wundef warning
wifi: iwlwifi: mld: reduce scope for uninitialized variable
====================
SMC consists of two sockets: smc_sock and kernel TCP socket.
Currently, there are two ways of creating the sockets, and syzbot reported
a lockdep splat [0] for the newer way introduced by commit d25a92ccae6b
("net/smc: Introduce IPPROTO_SMC").
socket(AF_SMC , SOCK_STREAM, SMCPROTO_SMC or SMCPROTO_SMC6)
socket(AF_INET or AF_INET6, SOCK_STREAM, IPPROTO_SMC)
When a socket is allocated, sock_lock_init() sets a lockdep lock class to
sk->sk_lock.slock based on its protocol family. In the IPPROTO_SMC case,
AF_INET or AF_INET6 lock class is assigned to smc_sock.
The repro sets IPV6_JOIN_ANYCAST for IPv6 UDP and SMC socket and exercises
smc_switch_to_fallback() for IPPROTO_SMC.
1. smc_switch_to_fallback() is called under lock_sock() and holds
smc->clcsock_release_lock.
2. Setting IPV6_JOIN_ANYCAST to SMC holds smc->clcsock_release_lock
and calls setsockopt() for the kernel TCP socket, which holds RTNL
and the kernel socket's lock_sock().
Add a mutex around the PTM transaction to prevent multiple transactors
Multiple processes try to initiate a PTM transaction, one or all may
fail. This can be reproduced by running two instances of the
following:
$ sudo phc2sys -O 0 -i tsn0 -m
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
Note: Normally two instance of PHC2SYS will not run, but one process
should not break another.
Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()") Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Christopher S M Hall [Tue, 1 Apr 2025 23:35:33 +0000 (16:35 -0700)]
igc: cleanup PTP module if probe fails
Make sure that the PTP module is cleaned up if the igc_probe() fails by
calling igc_ptp_stop() on exit.
Fixes: d89f88419f99 ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support") Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Christopher S M Hall [Tue, 1 Apr 2025 23:35:32 +0000 (16:35 -0700)]
igc: handle the IGC_PTP_ENABLED flag correctly
All functions in igc_ptp.c called from igc_main.c should check the
IGC_PTP_ENABLED flag. Adding check for this flag to stop and reset
functions.
Fixes: 5f2958052c58 ("igc: Add basic skeleton for PTP") Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Christopher S M Hall [Tue, 1 Apr 2025 23:35:31 +0000 (16:35 -0700)]
igc: move ktime snapshot into PTM retry loop
Move ktime_get_snapshot() into the loop. If a retry does occur, a more
recent snapshot will result in a more accurate cross-timestamp.
Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Tested-by: Avigail Dahan <avigailx.dahan@intel.com> Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Christopher S M Hall [Tue, 1 Apr 2025 23:35:30 +0000 (16:35 -0700)]
igc: increase wait time before retrying PTM
The i225/i226 hardware retries if it receives an inappropriate response
from the upstream device. If the device retries too quickly, the root
port does not respond.
The wait between attempts was reduced from 10us to 1us in commit 6b8aa753a9f9 ("igc: Decrease PTM short interval from 10 us to 1 us"), which
said:
With the 10us interval, we were seeing PTM transactions take around
12us. Hardware team suggested this interval could be lowered to 1us
which was confirmed with PCIe sniffer. With the 1us interval, PTM
dialogs took around 2us.
While a 1us short cycle time was thought to be theoretically sufficient, it
turns out in practice it is not quite long enough. It is unclear if the
problem is in the root port or an issue in i225/i226.
Increase the wait from 1us to 4us. Increasing to 2us appeared to work in
practice on the setups we have available. A value of 4us was chosen due to
the limited hardware available for testing, with a goal of ensuring we wait
long enough without overly penalizing the response time when unnecessary.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
Fixes: 6b8aa753a9f9 ("igc: Decrease PTM short interval from 10 us to 1 us") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Tested-by: Avigail Dahan <avigailx.dahan@intel.com> Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Christopher S M Hall [Tue, 1 Apr 2025 23:35:29 +0000 (16:35 -0700)]
igc: fix PTM cycle trigger logic
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced.
Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Tested-by: Avigail Dahan <avigailx.dahan@intel.com> Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com> Reviewed-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Corinna Vinschen <vinschen@redhat.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since the original bug seems to have been around for years,
but a new issue was report with the fix, revert the fix for
now. We have a couple of weeks to figure it out for this
release, if needed.
Reported-by: Bert Karwatzki <spasswolf@web.de> Closes: https://lore.kernel.org/linux-wireless/20250410215527.3001-1-spasswolf@web.de Fixes: a104042e2bf6 ("wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: iwlwifi: mld: Restart firmware on iwl_mld_no_wowlan_resume() error
Commit 44605365f935 ("iwlwifi: mld: fix building with CONFIG_PM_SLEEP
disabled") sought to fix build breakage, but inadvertently introduced
a new issue:
iwl_mld_mac80211_start() no longer calls iwl_mld_start_fw() after having
called iwl_mld_stop_fw() in the error path of iwl_mld_no_wowlan_resume().
Johannes Berg [Fri, 11 Apr 2025 08:40:54 +0000 (10:40 +0200)]
wifi: iwlwifi: pcie: set state to no-FW before reset handshake
The reset handshake attempts to kill the firmware, and it'll go
into a pretty much dead state once we do that. However, if it
times out, then we'll attempt to dump the firmware to be able
to see why it didn't respond. During this dump, we cannot treat
it as if it was still running, since we just tried to kill it,
otherwise dumping will attempt to send a DBGC stop command. As
this command will time out, we'll go into a reset loop.
For now, fix this by setting the trans->state to say firmware
isn't running before doing the reset handshake. In the longer
term, we should clean up the way this state is handled.
It's not entirely clear but it seems likely that this issue was
introduced by my rework of the error handling, prior to that it
would've been synchronous at that point and (I think) not have
attempted to reset since it was already doing down.
Xin Long [Tue, 8 Apr 2025 17:46:17 +0000 (13:46 -0400)]
ipv6: add exception routes to GC list in rt6_insert_exception
Commit 5eb902b8e719 ("net/ipv6: Remove expired routes with a separated list
of routes.") introduced a separated list for managing route expiration via
the GC timer.
However, it missed adding exception routes (created by ip6_rt_update_pmtu()
and rt6_do_redirect()) to this GC list. As a result, these exceptions were
never considered for expiration and removal, leading to stale entries
persisting in the routing table.
This patch fixes the issue by calling fib6_add_gc_list() in
rt6_insert_exception(), ensuring that exception routes are properly tracked
and garbage collected when expired.
David Wei [Wed, 9 Apr 2025 16:31:53 +0000 (09:31 -0700)]
io_uring/zcrx: enable tcp-data-split in selftest
For bnxt when the agg ring is used then tcp-data-split is automatically
reported to be enabled, but __net_mp_open_rxq() requires tcp-data-split
to be explicitly enabled by the user.
Enable tcp-data-split explicitly in io_uring zc rx selftest.
Fixes: 288c06973daa ("Bluetooth: Enforce key size of 16 bytes on FIPS level") Signed-off-by: FrĂŠdĂŠric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: btnxpuart: Add an error message if FW dump trigger fails
This prints an error message if the FW Dump trigger command fails. This
scenario is mainly observed in legacy chipsets 8987 and 8997 and also
IW416, where this feature is unavailable due to memory constraints.
Fixes: 998e447f443f ("Bluetooth: btnxpuart: Add support for HCI coredump feature") Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: btnxpuart: Revert baudrate change in nxp_shutdown
This reverts the change baudrate logic in nxp_shutdown.
Earlier, when the driver was removed, it restored the controller
baudrate to fw_init_baudrate, so that on re-loading the driver, things
work fine.
However, if the driver was removed while hci0 interface is down, the
change baudrate vendor command could not be sent by the driver. When the
driver was re-loaded, host and controller baudrate would be mismatched
and hci initialization would fail. The only way to recover would be to
reboot the system.
This issue was fixed by moving the restore baudrate logic from
nxp_serdev_remove() to nxp_shutdown().
This fix however caused another issue with the command "hciconfig hci0
reset", which makes hci0 DOWN and UP immediately.
Running "bluetoothctl power off" and "bluetoothctl power on" in a tight
loop works fine.
To maintain support for "hciconfig reset" command, the above mentioned fix
is reverted.
Fixes: 6fca6781d19d ("Bluetooth: btnxpuart: Move vendor specific initialization to .post_init") Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pauli Virtanen [Thu, 3 Apr 2025 16:57:59 +0000 (19:57 +0300)]
Bluetooth: increment TX timestamping tskey always for stream sockets
Documentation/networking/timestamping.rst implies TX timestamping OPT_ID
tskey increments for each sendmsg. In practice: TCP socket increments
it for all sendmsg, timestamping on or off, but UDP only when
timestamping is on. The user-visible counter resets when OPT_ID is
turned on, so difference can be seen only if timestamping is enabled for
some packets only (eg. via SO_TIMESTAMPING CMSG).
Fix BT sockets to work in the same way: stream sockets increment tskey
for all sendmsg (seqpacket already increment for timestamped only).
Fixes: 134f4b39df7b ("Bluetooth: add support for skb TX SND/COMPLETION timestamping") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file. However, if it loaded
a zero length file then the error code is not set correctly. It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference. This was detected by Smatch:
drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'
Fixes: 26503ad25de8 ("Bluetooth: btrtl: split the device initialization into smaller parts") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 1 Apr 2025 17:02:08 +0000 (13:02 -0400)]
Bluetooth: hci_event: Fix sending MGMT_EV_DEVICE_FOUND for invalid address
This fixes sending MGMT_EV_DEVICE_FOUND for invalid address
(00:00:00:00:00:00) which is a regression introduced by a2ec905d1e16 ("Bluetooth: fix kernel oops in store_pending_adv_report")
since in the attempt to skip storing data for extended advertisement it
actually made the code to skip the entire if statement supposed to send
MGMT_EV_DEVICE_FOUND without attempting to use the last_addr_adv which
is garanteed to be invalid for extended advertisement since we never
store anything on it.
* tag 'net-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (38 commits)
ethtool: cmis_cdb: Fix incorrect read / write length extension
selftests: netfilter: add test case for recent mismatch bug
nft_set_pipapo: fix incorrect avx2 match of 5th field octet
net: ppp: Add bound checking for skb data on ppp_sync_txmung
net: Fix null-ptr-deref by sock_lock_init_class_and_name() and rmmod.
ipv6: Align behavior across nexthops during path selection
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
net: phy: move phy_link_change() prior to mdio_bus_phy_may_suspend()
selftests/tc-testing: sfq: check that a derived limit of 1 is rejected
net_sched: sch_sfq: move the limit validation
net_sched: sch_sfq: use a temporary work area for validating configuration
net: libwx: handle page_pool_dev_alloc_pages error
selftests: mptcp: validate MPJoin HMacFailure counters
mptcp: only inc MPJoinAckHMacFailure for HMAC failures
rtnetlink: Fix bad unlock balance in do_setlink().
net: ethtool: Don't call .cleanup_data when prepare_data fails
tc: Ensure we have enough buffer space when sending filter netlink notifications
net: libwx: Fix the wrong Rx descriptor field
octeontx2-pf: qos: fix VF root node parent queue index
selftests: tls: check that disconnect does nothing
...
Merge tag 'for-linus-6.15a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A simple fix adding the module description of the Xenbus frontend
module
- A fix correcting the xen-acpi-processor Kconfig dependency for PVH
Dom0 support
- A fix for the Xen balloon driver when running as Xen Dom0 in PVH mode
- A fix for PVH Dom0 in order to avoid problems with CPU idle and
frequency drivers conflicting with Xen
* tag 'for-linus-6.15a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: disable CPU idle and frequency drivers for PVH dom0
x86/xen: fix balloon target initialization for PVH dom0
xen: Change xen-acpi-processor dom0 dependency
xenbus: add module description
Merge tag 'block-6.15-20250410' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Add a missing ublk selftest script, from test additions added last
week
- Two fixes for ublk error recovery and reissue
- Cleanup of ublk argument passing
* tag 'block-6.15-20250410' of git://git.kernel.dk/linux:
ublk: pass ublksrv_ctrl_cmd * instead of io_uring_cmd *
ublk: don't fail request for recovery & reissue in case of ubq->canceling
ublk: fix handling recovery & reissue in ublk_abort_queue()
selftests: ublk: fix test_stripe_04
Merge tag 'io_uring-6.15-20250410' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Reject zero sized legacy provided buffers upfront. No ill side
effects from this one, only really done to shut up a silly syzbot
test case.
- Fix for a regression in tag posting for registered files or buffers,
where the tag would be posted even when the registration failed.
- two minor zcrx cleanups for code added this merge window.
* tag 'io_uring-6.15-20250410' of git://git.kernel.dk/linux:
io_uring/kbuf: reject zero sized provided buffers
io_uring/zcrx: separate niov number from pages
io_uring/zcrx: put refill data into separate cache line
io_uring: don't post tag CQEs on file/buffer registration failure
Merge tag 'gpio-fixes-for-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix resource handling in gpio-tegra186
- fix wakeup source leaks in gpio-mpc8xxx and gpio-zynq
- fix minor issues with some GPIO OF quirks
- deprecate GPIOD_FLAGS_BIT_NONEXCLUSIVE and devm_gpiod_unhinge()
symbols and add a TODO task to track replacing them with a better
solution
* tag 'gpio-fixes-for-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: of: Move Atmel HSMCI quirk up out of the regulator comment
gpiolib: of: Fix the choice for Ingenic NAND quirk
gpio: zynq: Fix wakeup source leaks on device unbind
gpio: mpc8xxx: Fix wakeup source leaks on device unbind
gpio: TODO: track the removal of regulator-related workarounds
MAINTAINERS: add more keywords for the GPIO subsystem entry
gpio: deprecate devm_gpiod_unhinge()
gpio: deprecate the GPIOD_FLAGS_BIT_NONEXCLUSIVE flag
gpio: tegra186: fix resource handling in ACPI probe path
Merge tag 'mtd/fixes-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"Two important fixes: the build of the SPI NAND layer with old GCC
versions as well as the fix of the Qpic Makefile which was wrong in
the first place.
There are also two smaller fixes about a missing error and status
check"
* tag 'mtd/fixes-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spinand: Fix build with gcc < 7.5
mtd: rawnand: Add status chack in r852_ready()
mtd: inftlcore: Add error check for inftl_read_oob()
mtd: nand: Drop explicit test for built-in CONFIG_SPI_QPIC_SNAND
The 'read_write_len_ext' field in 'struct ethtool_cmis_cdb_cmd_args'
stores the maximum number of bytes that can be read from or written to
the Local Payload (LPL) page in a single multi-byte access.
Cited commit started overwriting this field with the maximum number of
bytes that can be read from or written to the Extended Payload (LPL)
pages in a single multi-byte access. Transceiver modules that support
auto paging can advertise a number larger than 255 which is problematic
as 'read_write_len_ext' is a 'u8', resulting in the number getting
truncated and firmware flashing failing [1].
Fix by ignoring the maximum EPL access size as the kernel does not
currently support auto paging (even if the transceiver module does) and
will not try to read / write more than 128 bytes at once.
[1]
Transceiver module firmware flashing started for device enp177s0np0
Transceiver module firmware flashing in progress for device enp177s0np0
Progress: 0%
Transceiver module firmware flashing encountered an error for device enp177s0np0
Status message: Write FW block EPL command failed, LPL length is longer
than CDB read write length extension allows.
Fixes: 9a3b0d078bd8 ("net: ethtool: Add support for writing firmware blocks using EPL payload") Reported-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Closes: https://lore.kernel.org/netdev/20250402183123.321036-3-michael.chan@broadcom.com/ Tested-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Link: https://patch.msgid.link/20250409112440.365672-1-idosch@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 10 Apr 2025 11:13:35 +0000 (13:13 +0200)]
Merge tag 'nf-25-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains a Netfilter fix and improved test coverage:
1) Fix AVX2 matching in nft_pipapo, from Florian Westphal.
2) Extend existing test to improve coverage for the aforementioned bug,
also from Florian.
netfilter pull request 25-04-10
* tag 'nf-25-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
selftests: netfilter: add test case for recent mismatch bug
nft_set_pipapo: fix incorrect avx2 match of 5th field octet
====================
selftests: netfilter: add test case for recent mismatch bug
Without 'nft_set_pipapo: fix incorrect avx2 match of 5th field octet"
this fails:
TEST: reported issues
Add two elements, flush, re-add 1s [ OK ]
net,mac with reload 0s [ OK ]
net,port,proto 3s [ OK ]
avx2 false match 0s [FAIL]
False match for fe80:dead:01fe:0a02:0b03:6007:8009:a001
Other tests do not detect the kernel bug as they only alter parts in
the /64 netmask.
nft_set_pipapo: fix incorrect avx2 match of 5th field octet
Given a set element like:
icmpv6 . dead:beef:00ff::1
The value of 'ff' is irrelevant, any address will be matched
as long as the other octets are the same.
This is because of too-early register clobbering:
ymm7 is reloaded with new packet data (pkt[9]) but it still holds data
of an earlier load that wasn't processed yet.
The existing tests in nft_concat_range.sh selftests do exercise this code
path, but do not trigger incorrect matching due to the network prefix
limitation.
net: ppp: Add bound checking for skb data on ppp_sync_txmung
Ensure we have enough data in linear buffer from skb before accessing
initial bytes. This prevents potential out-of-bounds accesses
when processing short packets.
When ppp_sync_txmung receives an incoming package with an empty
payload:
(remote) gef⤠p *(struct pppoe_hdr *) (skb->head + skb->network_header)
$18 = {
type = 0x1,
ver = 0x1,
code = 0x0,
sid = 0x2,
length = 0x0,
tag = 0xffff8880371cdb96
}
from the skb struct (trimmed)
tail = 0x16,
end = 0x140,
head = 0xffff88803346f400 "4",
data = 0xffff88803346f416 ":\377",
truesize = 0x380,
len = 0x0,
data_len = 0x0,
mac_len = 0xe,
hdr_len = 0x0,
net: Fix null-ptr-deref by sock_lock_init_class_and_name() and rmmod.
When I ran the repro [0] and waited a few seconds, I observed two
LOCKDEP splats: a warning immediately followed by a null-ptr-deref. [1]
Reproduction Steps:
1) Mount CIFS
2) Add an iptables rule to drop incoming FIN packets for CIFS
3) Unmount CIFS
4) Unload the CIFS module
5) Remove the iptables rule
At step 3), the CIFS module calls sock_release() for the underlying
TCP socket, and it returns quickly. However, the socket remains in
FIN_WAIT_1 because incoming FIN packets are dropped.
At this point, the module's refcnt is 0 while the socket is still
alive, so the following rmmod command succeeds.
# ss -tan
State Recv-Q Send-Q Local Address:Port Peer Address:Port
FIN-WAIT-1 0 477 10.0.2.15:51062 10.0.0.137:445
This highlights a discrepancy between the lifetime of the CIFS module
and the underlying TCP socket. Even after CIFS calls sock_release()
and it returns, the TCP socket does not die immediately in order to
close the connection gracefully.
While this is generally fine, it causes an issue with LOCKDEP because
CIFS assigns a different lock class to the TCP socket's sk->sk_lock
using sock_lock_init_class_and_name().
Once an incoming packet is processed for the socket or a timer fires,
sk->sk_lock is acquired.
Then, LOCKDEP checks the lock context in check_wait_context(), where
hlock_class() is called to retrieve the lock class. However, since
the module has already been unloaded, hlock_class() logs a warning
and returns NULL, triggering the null-ptr-deref.
If LOCKDEP is enabled, we must ensure that a module calling
sock_lock_init_class_and_name() (CIFS, NFS, etc) cannot be unloaded
while such a socket is still alive to prevent this issue.
Let's hold the module reference in sock_lock_init_class_and_name()
and release it when the socket is freed in sk_prot_free().
Note that sock_lock_init() clears sk->sk_owner for svc_create_socket()
that calls sock_lock_init_class_and_name() for a listening socket,
which clones a socket by sk_clone_lock() without GFP_ZERO.
ipv6: Align behavior across nexthops during path selection
A nexthop is only chosen when the calculated multipath hash falls in the
nexthop's hash region (i.e., the hash is smaller than the nexthop's hash
threshold) and when the nexthop is assigned a non-negative score by
rt6_score_route().
Commit 4d0ab3a6885e ("ipv6: Start path selection from the first
nexthop") introduced an unintentional difference between the first
nexthop and the rest when the score is negative.
When the first nexthop matches, but has a negative score, the code will
currently evaluate subsequent nexthops until one is found with a
non-negative score. On the other hand, when a different nexthop matches,
but has a negative score, the code will fallback to the nexthop with
which the selection started ('match').
Align the behavior across all nexthops and fallback to 'match' when the
first nexthop matches, but has a negative score.
Fixes: 3d709f69a3e7 ("ipv6: Use hash-threshold instead of modulo-N") Fixes: 4d0ab3a6885e ("ipv6: Start path selection from the first nexthop") Reported-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Closes: https://lore.kernel.org/netdev/67efef607bc41_1ddca82948c@willemb.c.googlers.com.notmuch/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250408084316.243559-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Mon, 7 Apr 2025 09:40:42 +0000 (12:40 +0300)]
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d16 ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed by the MAC, we will
make the MDIO bus PM ops treat identically the phylink-controlled PHYs
with the phylib-controlled PHYs where an adjust_link() callback is
supplied. In both cases, the MDIO bus PM ops should stop and restart the
PHY state machine.
Vladimir Oltean [Mon, 7 Apr 2025 09:38:59 +0000 (12:38 +0300)]
net: phy: move phy_link_change() prior to mdio_bus_phy_may_suspend()
In an upcoming change, mdio_bus_phy_may_suspend() will need to
distinguish a phylib-based PHY client from a phylink PHY client.
For that, it will need to compare the phydev->phy_link_change() function
pointer with the eponymous phy_link_change() provided by phylib.
To avoid forward function declarations, the default PHY link state
change method should be moved upwards. There is no functional change
associated with this patch, it is only to reduce the noise from a real
bug fix.
Merge tag 'linux_kselftest-fixes-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- Fixes tpm2, futex, and mincore tests
- Create a dedicated .gitignore for tpm2 tests
* tag 'linux_kselftest-fixes-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/mincore: Allow read-ahead pages to reach the end of the file
selftests/futex: futex_waitv wouldblock test should fail
selftests: tpm2: test_smoke: use POSIX-conformant expression operator
selftests: tpm2: create a dedicated .gitignore
ublk: pass ublksrv_ctrl_cmd * instead of io_uring_cmd *
The ublk_ctrl_*() handlers all take struct io_uring_cmd *cmd but only
use it to get struct ublksrv_ctrl_cmd *header from the io_uring SQE.
Since the caller ublk_ctrl_uring_cmd() has already computed header, pass
it instead of cmd.
Ming Lei [Wed, 9 Apr 2025 01:14:42 +0000 (09:14 +0800)]
ublk: don't fail request for recovery & reissue in case of ubq->canceling
ubq->canceling is set with request queue quiesced when io_uring context is
exiting. USER_RECOVERY or !RECOVERY_FAIL_IO requires request to be re-queued
and re-dispatch after device is recovered.
However commit d796cea7b9f3 ("ublk: implement ->queue_rqs()") still may fail
any request in case of ubq->canceling, this way breaks USER_RECOVERY or
!RECOVERY_FAIL_IO.
Fix it by calling __ublk_abort_rq() in case of ubq->canceling.
projects / nvme.git / log