Arnd Bergmann [Thu, 16 Jan 2025 13:43:26 +0000 (14:43 +0100)]
Merge tag 'sti-dt-for-v6.14-round1' of https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
Add and enable MALI400 support for STiH410-b2260
* tag 'sti-dt-for-v6.14-round1' of https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: st: enable the MALI gpu on the stih410-b2260
ARM: dts: st: add node for the MALI gpu on stih410.dtsi
dt-bindings: gpu: mali-utgard: Add st,stih410-mali compatible
Arnd Bergmann [Thu, 16 Jan 2025 13:41:30 +0000 (14:41 +0100)]
Merge tag 'imx-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm64 device tree change for 6.14:
- Add simple-framebuffer support for imx8mn-bsh-smm-s2/pro board
(Dario Binacchi)
- Add LVDS compatible string for imx8mm-phg board (Fabio Estevam)
- Add P3T1085 temperature sensor support for imx93-9x9-qsb board (Frank Li)
- Add support for i.MX8MP based aristainetos3 boards from ABB
(Heiko Schocher)
- Add PCA9452 system PMIC support for imx93-14x14-evk board (Joy Zou)
- Support NXP LVDS to HDMI adapter cards for imx8mp-evk board with DT
overlays (Liu Ying)
- A couple of changes from Markus Niebel to enable Open Drain for MDIO
on imx93-tqma9352 boards
- A series from Peng Fan to enable wdog3 fsl,ext-reset-output support
for NXP i.MX93 boards
- A couple changes from Wei Fang to add NETC support for i.MX95
* tag 'imx-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx93-9x9-qsb: enable fsl,ext-reset-output for wdog3
arm64: dts: freescale: imx93-14x14-evk: enable fsl,ext-reset-output for wdog3
arm64: dts: freescale: imx93-11x11-evk: enable fsl,ext-reset-output for wdog3
arm64: dts: imx95-19x19-evk: add ENETC 0 support
arm64: dts: imx95: add NETC related nodes
arm64: dts: imx8mm-phg: Add LVDS compatible string
arm64: dts: imx93: add pca9452 support
arm64: dts: imx8mn-bsh-smm-s2/pro: add simple-framebuffer
arm64: dts: imx93-tqma9352-mba93xxla: enable Open Drain for MDIO
arm64: dts: imx93-tqma9352-mba93xxca: enable Open Drain for MDIO
arm64: dts: imx93-9x9-qsb: add temp-sensor nxp,p3t1085
arm64: dts: imx8mp-evk: Add NXP LVDS to HDMI adapter cards
arm64: dts: imx8mp-skov-revb-mi1010ait-1cp1: Set "media_disp2_pix" clock rate to 70MHz
arm64: dts: imx8mp: add aristainetos3 board support
arm64: dts: imx8mq-zii-ultra: remove #address-cells of eeprom@a4
arm64: dts: imx: Switch to simple-audio-card,hp-det-gpios
Arnd Bergmann [Thu, 16 Jan 2025 13:40:29 +0000 (14:40 +0100)]
Merge tag 'imx-dt-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.14:
- Clean up TQMa7x device trees (Alexander Stein)
- Correct node name pattern for mdio-gpio devices (Fabio Estevam)
- Update deprecated GPIO properties for Generic ASoC Sound Card device
(Geert Uytterhoeven)
- Set USB dr_mode property to OTG explicitly for imx6qdl-sabresd based
boards (Hui Wang)
- Update MAINTAINERS entry for DH electronics DHSOM boards (Marek Vasut)
- A series from Stefan Kerkmann to add phy-3p0-supply for usb phys
* tag 'imx-dt-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Use the correct mdio pattern
ARM: dts: imx6qdl-sabresd: add dr_mode to usbotg
ARM: dts: imx6qdl-apalis: Change to "adi,force-bt656-4"
ARM: dts: imx6sx: add phy-3p0-supply to usb phys
ARM: dts: imx6sl: add phy-3p0-supply to usb phys
ARM: dts: imx6qdl: add phy-3p0-supply to usb phys
MAINTAINERS: Update entry for DH electronics DHSOM SoMs and boards
ARM: dts: imx7[d]-mba7: add Ethernet PHY IRQ support
ARM: dts: imx7-mba7: Remove duplicated power supply
ARM: dts: imx7-mba7: Fix SD card vmmc-supply
ARM: dts: imx7-mba7: Add 3.3V and 5.0V regulators
ARM: dts: imx7-tqma7: add missing vs-supply for LM75A (rev. 01xxx)
ARM: dts: imx7-tqma7: Remove superfluous status="okay" property
ARM: dts: imx7-mba7: remove LVDS transmitter regulator
ARM: dts: imx: Switch to {hp,mic}-det-gpios
Arnd Bergmann [Thu, 16 Jan 2025 13:39:10 +0000 (14:39 +0100)]
Merge tag 'socfpga_dts_updates_v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt
SoCFPGA DTS updates for v6.14
- Remove unused and undocumented property "snps,max-mtu"
- Add gpio and spi node for Agilex5
- Add VGIC maintenance interrupt for Agilex
- Use correct reset name of "stmmaceth-ocp" instead of "ahb"
- Drop unused #address-cells/#size-cells in the cyclone5-mcvevk
* tag 'socfpga_dts_updates_v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: altera: Remove unused and undocumented "snps,max-mtu" property
arm64: dts: socfpga: agilex5: Add gpio0 node and spi dma handshake id
arm64: dts: socfpga: agilex: Add VGIC maintenance interrupt
arm: dts: socfpga: use reset-name "stmmaceth-ocp" instead of "ahb"
ARM: dts: socfpga_cyclone5_mcvevk: Drop unused #address-cells/#size-cells
Arnd Bergmann [Thu, 16 Jan 2025 13:38:22 +0000 (14:38 +0100)]
Merge tag 'hisi-arm64-dt-for-6.14' of https://github.com/hisilicon/linux-hisi into soc/dt
ARM64: DT: HiSilicon ARM64 DT updates for v6.14
- Remove "enable-dma" and "bus-id" properties from the spi node on hi6220
* tag 'hisi-arm64-dt-for-6.14' of https://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Remove unused and undocumented "enable-dma" and "bus-id" properties
Arnd Bergmann [Thu, 16 Jan 2025 13:37:20 +0000 (14:37 +0100)]
Merge tag 'dt-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.14
1. Marvell: Use un-deprecated hp-det-gpios (no ABI impact expected).
2. SoCFPGA: Drop spidev devices which are not properly described in DTS,
but are using some other compatibles. This was part of wider tree
effort to fix such incorrect hardware descriptions.
Important: Dropping this device node will have user-visible impact:
spidev device will not register.
* tag 'dt-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: socfpga: remove non-existent DAC from CycloneV devkit
ARM: dts: marvell: mmp2-olpc-xo-1-75: Switch to {hp,mic}-det-gpios
Arnd Bergmann [Thu, 16 Jan 2025 12:39:42 +0000 (13:39 +0100)]
Merge tag 'dt64-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM64 DTS for v6.14
1. Spreadtrum:
- Correct few issues pointed out by DT schema around properties and
node names.
- Move fuel-gauge from DTSI to DTS, because it belongs to the board.
- Use undeprecated properties, like battery-detect-gpios, already
supported by Linux.
2. Uniphier: Use un-deprecated hp-det-gpios (no ABI impact expected).
Arnd Bergmann [Wed, 15 Jan 2025 17:51:13 +0000 (18:51 +0100)]
Merge tag 'samsung-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.14
1. Exynos8895: Add UART nodes, PMU (performance) for the M2 cluster and
I2C controllers in the camera block (HSI2C in CAM0-3).
2. Exynos990: Add Power Management Unit (Samsung block), PMU
(performance) for M5 cluster and two clock controllers.
3. ExynosAutov920: Add watchdog and DMA controllers.
4. Google GS101: Minor fixes for phy and USB. Add USB Type-C.
5. Exynos850-e850-96 board: Drop gap in memory layout.
6. New SoC: Exynos9810.
7. New boards, all mobile phones:
- Exynos9810:
Samsung Galaxy S9 (SM-G960F)
- Exynos990:
Samsung Galaxy S20 FE (SM-G780F)
Samsung Galaxy S20 5G (SM-G980F)
* tag 'samsung-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (23 commits)
arm64: dts: exynos8895: Add camera hsi2c nodes
arm64: dts: exynos990: Add clock management unit nodes
arm64: dts: exynos: gs101-oriole: add pd-disable and typec-power-opmode
arm64: dts: exynos: gs101-oriole: enable Maxim max77759 TCPCi
arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F)
arm64: dts: exynos: Add Exynos9810 SoC support
arm64: dts: exynos850-e850-96: Specify reserved secure memory explicitly
arm64: dts: exynos990: Add a PMU node for the third cluster
arm64: dts: exynosautov920: Add DMA nodes
arm64: dts: exynos8895: Add a PMU node for the second cluster
dt-bindings: clock: samsung: Add Exynos990 SoC CMU bindings
arm64: dts: exynosautov920: add watchdog DT node
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 (x1slte)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 5G (x1s)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 Series boards (x1s-common)
dt-bindings: arm: samsung: samsung-boards: Add bindings for SM-G981B and SM-G980F board
arm64: dts: exynos: gs101: allow stable USB phy Vbus detection
arm64: dts: exynos: gs101: phy region for exynos5-usbdrd is larger
MAINTAINERS: add myself and Tudor as reviewers for Google Tensor SoC
arm64: dts: exynos990: Add pmu and syscon-reboot nodes
...
Wei Fang [Thu, 19 Dec 2024 06:13:40 +0000 (14:13 +0800)]
arm64: dts: imx95-19x19-evk: add ENETC 0 support
Add ENETC 0 (1G ethernet port) support for i.MX95-19x19-EVK board. In
addition, because all ENETC instances share MDIO bus, so enable EMDIO
at the same time.
Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hui Wang [Mon, 16 Dec 2024 04:07:22 +0000 (12:07 +0800)]
ARM: dts: imx6qdl-sabresd: add dr_mode to usbotg
Currently there are 3 type of boards (imx6q|imx6qp|imx6dl-sabresd)
based on imx6qdl-sabresd.dtsi, they all do not set the dr_mode for
usbotg device node. The chipidea usb driver will configure it to otg
mode by default if the dr_mode is not set, but some testcases need to
parse the dr_mode from DT and decide the follow-up test strategy, here
set the dr_mode to otg explicitly for these 3 imx6qdl-sabresd based
boards.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mm-phg board has an AUO G084SN05 V9 8.4" 800x600 LVDS panel.
Improve the devicetree description by passing the LVDS compatible
string to fix the following dt-schema warning:
imx8mm-phg.dtb: panel: compatible:0: 'panel-lvds' is not one of
['admatec,9904379', 'auo,b101ew05', 'auo,g084sn05',
'chunghwa,claa070wp03xg','edt,etml0700z9ndha', 'hannstar,hsd101pww2',
'hydis,hv070wx2-1e0', 'jenson,bl-jt60050-01a', 'tbs,a711-panel']
...
Markus Niebel [Thu, 5 Dec 2024 15:07:29 +0000 (16:07 +0100)]
arm64: dts: imx93-tqma9352-mba93xxla: enable Open Drain for MDIO
The board has a pull-up resistor for MDIO pin per PHY design guide.
When MDIO is idle, it needs to be high and open drain is better
to be used here for power saving.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Markus Niebel [Thu, 5 Dec 2024 15:07:28 +0000 (16:07 +0100)]
arm64: dts: imx93-tqma9352-mba93xxca: enable Open Drain for MDIO
The board has a pull-up resistor for MDIO pin per PHY design guide.
When MDIO is idle, it needs to be high and open drain is better
to be used here for power saving.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Kerkmann [Tue, 26 Nov 2024 09:22:15 +0000 (10:22 +0100)]
ARM: dts: imx6sx: add phy-3p0-supply to usb phys
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The regulator handling was introduced by commit `966d73152078 (usb: phy:
mxs: enable regulator phy-3p0 to improve signal qualilty, 2024-07-26)`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Kerkmann [Tue, 26 Nov 2024 09:22:14 +0000 (10:22 +0100)]
ARM: dts: imx6sl: add phy-3p0-supply to usb phys
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d73152078 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Kerkmann [Tue, 26 Nov 2024 09:22:13 +0000 (10:22 +0100)]
ARM: dts: imx6qdl: add phy-3p0-supply to usb phys
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d73152078 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Artur Weber [Fri, 16 Aug 2024 07:51:02 +0000 (09:51 +0200)]
ARM: dts: samsung: exynos4212-tab3: Drop interrupt from WM1811 codec
This was initially copied from the Midas DTSI, but there is no
proof that the same interrupt is also used on the Tab 3. The pin
listed as the interrupt here is GPIO_HDMI_CEC on the Midas,
but for the Tab 3 it is the headset button GPIO - GPIO_EAR_SEND_END.
Drop the interrupt, since there is no proof that it is used.
In the schematics, the MCLK2 pin is shown as connected to CODEC_CLK32K,
which is derived from the same 32KHZ_PMIC clock as Bluetooth/WiFi and
GPS clocks. 32KHZ_PMIC is connected to the BTCLK pin, represented in
mainline as S2MPS11_CLK_BT.
Add the MCLK2 clock to the WM1811 codec clock property to properly
describe the hardware.
ARM: dts: socfpga: remove non-existent DAC from CycloneV devkit
There is no Rohm DAC on the CycloneV devkit according to the online
documentation for it that I could find, and it definitely does not have
a dh2228fv as this device does not actually exist! Remove the DAC node
from the devicetree as it is not acceptable to pretend to have a device
on a board in order to bind the spidev driver in Linux.
André Draszik [Tue, 3 Dec 2024 12:40:28 +0000 (12:40 +0000)]
arm64: dts: exynos: gs101-oriole: add pd-disable and typec-power-opmode
When the serial console is enabled, we need to disable power delivery
since serial uses the SBU1/2 pins and appears to confuse the TCPCI,
resulting in endless interrupts.
For now, change the DT such that the serial console continues working.
Note1: We can not have both typec-power-opmode and
new-source-frs-typec-current active at the same time, as otherwise DT
binding checks complain.
Note2: When using a downstream DT, the Pixel boot-loader will modify
the DT accordingly before boot, but for this upstream DT it doesn't
know where to find the TCPCI node. The intention is for this commit to
be reverted once an updated Pixel boot-loader becomes available.
On Pixel 6 (and Pro), a max77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
* top (including GPIO)
* charger
* fuel gauge
* TCPCi
While in the same package, TCPCi and Fuel Gauge have separate I2C
addresses, interrupt lines and interrupt status registers and can be
treated independently.
The TCPCi is required to detect and handle connector orientation in
Pixel's USB PHY driver, and to configure the USB controller's role
(host vs device).
This change adds the TCPCi part as it can be independent and doesn't
need a top-level MFD.
Markuss Broks [Sat, 14 Dec 2024 14:56:47 +0000 (16:56 +0200)]
arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F)
Samsung Galaxy S9 (SM-G960F), codenamed starlte, is a mobile phone
released in 2017. It has 4GB of RAM, 64GB of UFS storage, Exynos9810
SoC and 1440x2960 Super AMOLED display.
This initial device tree enables the framebuffer pre-initialised
by bootloader and physical buttons of the device, with more support
to come in the future.
Markuss Broks [Sat, 14 Dec 2024 14:56:46 +0000 (16:56 +0200)]
arm64: dts: exynos: Add Exynos9810 SoC support
Exynos 9810 is an ARMv8 mobile SoC found in various Samsung devices,
such as Samsung Galaxy S9 (starlte), S9 Plus (star2lte),
Note 9 (crownlte) and perhaps others.
Add minimal support for this SoC, including basic stuff like:
- PSCI for bringing up secondary cores
- ARMv8 generic timer
- GPIO and pinctrl.
The firmware coming with the devices based on this SoC is buggy
and doesn't configure CNTFRQ_EL0, as required by spec, so it's
needed to hardcode the frequency in the timer node.
Co-developed-by: Maksym Holovach <nergzd@nergzd723.xyz> Signed-off-by: Maksym Holovach <nergzd@nergzd723.xyz> Signed-off-by: Markuss Broks <markuss.broks@gmail.com> Link: https://lore.kernel.org/r/20241214-exynos9810-v4-1-4e91fbbc2133@gmail.com
[krzysztof: Rename and move PMU nodes to proper sorting position] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Instead of carving out the secure area in 'memory' node, let's describe
it in 'reserved-memory'. That makes it easier to understand both RAM
regions and particular secure world memory region. Originally the device
tree was created in a way to make sure it was well aligned with the way
LittleKernel bootloader modified it. But later it was found the
LittleKernel works fine with properly described reserved regions, so
it's possible now to define those in a cleaner way.
Arnd Bergmann [Fri, 20 Dec 2024 16:45:12 +0000 (17:45 +0100)]
Merge tag 'renesas-dts-for-v6.14-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.14
- Add more serial (SCIF), power monitor, ADC, and sound support for
the RZ/G3S SoC and the RZ/G3S SMARC SoM and development board,
- Add support for the R-Car V4H ES3.0 (R8A779G3) SoC on the White Hawk
Single development board,
- Add display support for the R-Car V4M SoC and the Gray Hawk Single
development board,
- Add video capture support for the Gray Hawk Single development
board,
- Add initial support for the RZ/G3E (R9A09G047) SoC and the RZ/G3E
SMARC SoM and Carrier-II EVK development board,
- Add support for 5-port MATEnet on the Falcon Ethernet sub-board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.14-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (33 commits)
arm64: dts: renesas: r9a09g047: Add I2C nodes
arm64: dts: renesas: rzg3s-smarc: Add sound card
arm64: dts: renesas: rzg3s-smarc: Enable SSI3
arm64: dts: renesas: Add da7212 audio codec node
arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node
arm64: dts: renesas: r9a08g045: Add SSI nodes
arm64: dts: renesas: rzg3s-smarc-som: Enable ADC
arm64: dts: renesas: r9a08g045: Add ADC node
arm64: dts: renesas: Add initial device tree for RZ/G3E SMARC EVK board
arm64: dts: renesas: Add initial support for RZ/G3E SMARC SoM
arm64: dts: renesas: r9a09g047: Add OPP table
arm64: dts: renesas: Add initial DTSI for RZ/G3E SoC
arm64: dts: renesas: falcon-ethernet: Describe PHYs connected on the breakout board
arm64: dts: renesas: r8a779a0: Remove address- and size-cells from AVB[1-5]
dt-bindings: clock: renesas: Document RZ/G3E SoC CPG
dt-bindings: soc: renesas: Document RZ/G3E SMARC SoM and Carrier-II EVK
dt-bindings: soc: renesas: Document Renesas RZ/G3E SoC variants
arm64: dts: renesas: gray-hawk-single: Add video capture support
arm64: dts: renesas: gray-hawk-single: Add DisplayPort support
arm64: dts: renesas: r8a779h0: Add display support
...
Arnd Bergmann [Fri, 20 Dec 2024 16:40:06 +0000 (17:40 +0100)]
Merge tag 'stm32-dt-for-v6.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.14, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp135f-dk.
- DH core: increase CPU voltage to fit with STM32MP135F datasheet.
- STMP32MP15:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp15 EV1 and DK boards.
- OCTAVO:
- LXA-TAC (gen1/2): disable RTC, update aliases and
adjust USB gadget.
- Add LXA-TAC gen3 based on OSD32MP153x SIP:
STMP32MP153, RAM, PMIC.
- DH: minor fixes.
- STM32MP25:
- Enable imx335/CSI/DCMIPP pipeline on stm32mp257f-ev1.
- Add I2S, SAI, SPDIFRX supports.
- Add and enable COMBOPHY on stm32mp257f-ev1. Combophy is used
by PCIe and USB3.
* tag 'stm32-dt-for-v6.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (23 commits)
arm64: dts: st: enable imx335/csi/dcmipp pipeline on stm32mp257f-ev1
arm64: dts: st: add csi & dcmipp node in stm32mp25
ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM
ARM: dts: stm32: add counter subnodes on stm32mp157 dk boards
ARM: dts: stm32: add counter subnodes on stm32mp157c-ev1
ARM: dts: stm32: add counter subnodes on stm32mp135f-dk
ARM: dts: stm32: populate all timer counter nodes on stm32mp15
ARM: dts: stm32: populate all timer counter nodes on stm32mp13
ARM: dts: stm32: lxa-tac: Add support for generation 3 devices
ARM: dts: stm32: lxa-tac: move adc and gpio{e,g} to gen{1,2} boards
dt-bindings: arm: stm32: add compatible strings for Linux Automation LXA TAC gen 3
ARM: dts: stm32: lxa-tac: adjust USB gadget fifo sizes for multi function
ARM: dts: stm32: lxa-tac: extend the alias table
ARM: dts: stm32: lxa-tac: disable the real time clock
ARM: dts: stm32: Fix IPCC EXTI declaration on stm32mp151
ARM: dts: stm32: Sort M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT
ARM: dts: stm32: Increase CPU core voltage on STM32MP13xx DHCOR SoM
ARM: dts: stm32: Deduplicate serial aliases and chosen node for STM32MP15xx DHCOM SoM
arm64: dts: st: Enable COMBOPHY on the stm32mp257f-ev1 board
arm64: dts: st: Add combophy node on stm32mp251
...
Marek Vasut [Fri, 13 Dec 2024 22:36:25 +0000 (23:36 +0100)]
ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabrice Gasnier [Mon, 16 Dec 2024 15:39:05 +0000 (16:39 +0100)]
ARM: dts: stm32: populate all timer counter nodes on stm32mp15
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
Fabrice Gasnier [Mon, 16 Dec 2024 15:39:04 +0000 (16:39 +0100)]
ARM: dts: stm32: populate all timer counter nodes on stm32mp13
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
Mamta Shukla [Mon, 28 Oct 2024 14:59:07 +0000 (15:59 +0100)]
arm: dts: socfpga: use reset-name "stmmaceth-ocp" instead of "ahb"
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html Fixes: 331085a423b ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb") Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Faraz Ata [Thu, 12 Dec 2024 11:57:05 +0000 (17:27 +0530)]
arm64: dts: exynosautov920: Add DMA nodes
ExynosAutov920 SoC has 7 DMA controllers. Two secure DMAC
(SPDMA0 & SPDMA1) and five non-secure DMAC (PDMA0 to PDMA4).
Add the required dt nodes for the same.
Add dt-schema documentation for the Exynos990 SoC CMU.
This clock management unit has a topmost block (CMU_TOP)
that generates top clocks for other blocks. Currently the
only other block implemented is CMU_HSI0, which provides
clocks for the USB part of the SoC.
Also, device-tree binding definitions added for these blocks:
- CMU_TOP
- CMU_HSI0
Claudiu Beznea [Tue, 10 Dec 2024 17:09:49 +0000 (19:09 +0200)]
arm64: dts: renesas: r9a08g045: Add SSI nodes
Add DT nodes for the SSI IPs available on the Renesas RZ/G3S SoC. Along
with it external audio clocks were added. Board device tree could use it
and update the frequencies.
Biju Das [Tue, 3 Dec 2024 10:49:36 +0000 (10:49 +0000)]
arm64: dts: renesas: Add initial DTSI for RZ/G3E SoC
Add the initial DTSI for the RZ/G3E SoC.
The files in this commit have the following meaning:
- r9a09g047.dtsi: RZ/G3E family SoC common parts
- r9a09g047e57.dtsi: RZ/G3E R0A09G047E{4,5}{7,8} SoC specific parts
- r9a09g047e37.dtsi: RZ/G3E R0A09G047E{2,3}{7,8} SoC specific parts
Niklas Söderlund [Wed, 23 Oct 2024 15:46:42 +0000 (17:46 +0200)]
arm64: dts: renesas: r8a779a0: Remove address- and size-cells from AVB[1-5]
When describing the PHYs on the Falcon Ethernet breakout board mdio
nodes will be needed to describe the connections, and each mdio node
will need to contain these two properties instead. This will make the
address-cells and size-cells described in the base SoC include file
redundant and they will produce warnings, remove them.
Biju Das [Tue, 3 Dec 2024 10:49:30 +0000 (10:49 +0000)]
dt-bindings: soc: renesas: Document RZ/G3E SMARC SoM and Carrier-II EVK
Document the Renesas RZ/G3E SMARC Carrier-II EVK board which is based
on the Renesas RZ/G3E SMARC SoM. The RZ/G3E SMARC Carrier-II EVK
consists of an RZ/G3E SoM module and a SMARC Carrier-II carrier board.
The SoM module sits on top of the carrier board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Acked-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20241203105005.103927-4-biju.das.jz@bp.renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Niklas Söderlund [Mon, 9 Dec 2024 12:55:04 +0000 (13:55 +0100)]
arm64: dts: renesas: gray-hawk-single: Add video capture support
The Gray-Hawk single board contains two MAX96724 connected to the using
I2C and CSI-2, record the connections. Also enable all nodes (VIN, CSI-2
and ISP) that are part of the downstream video capture pipeline.
Geert Uytterhoeven [Thu, 5 Dec 2024 12:53:49 +0000 (13:53 +0100)]
arm64: dts: renesas: white-hawk-single: Add R-Car Sound support
White Hawk Single boards can use the same ARD-AUDIO-DA7212 external
audio board as the White Hawk board stack. Add support for building
DTBs for them, and document the small differences in connector labels.
Geert Uytterhoeven [Thu, 5 Dec 2024 12:53:48 +0000 (13:53 +0100)]
arm64: dts: renesas: white-hawk-ard-audio: Drop SoC part
The White Hawk with ARD-AUDIO-DA7212 external audio board stack is not
specific to R8A779G0. Hence rename its DTS file name to drop the
"r8a779g0-" prefix.
Claudiu Beznea [Fri, 15 Nov 2024 13:43:58 +0000 (15:43 +0200)]
arm64: dts: renesas: rzg3s-smarc: Fix the debug serial alias
The debug serial of the RZ/G3S is SCIF0 which is routed on the Renesas
RZ SMARC Carrier II board on the SER3_UART. Use serial3 alias for it for
better hardware description. Along with it, the chosen properties were
moved to the device tree corresponding to the RZ SMARC Carrier II board.
Fixes: adb4f0c5699c ("arm64: dts: renesas: Add initial support for RZ/G3S SMARC SoM") Fixes: d1ae4200bb26 ("arm64: dts: renesas: Add initial device tree for RZ SMARC Carrier-II Board") Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20241115134401.3893008-6-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
projects / users / jedix / linux-maple.git / log