The Exynos UFS controller only supports scatter/gather list elements that
are aligned on a 4 KiB boundary. Fix DMA alignment in case PAGE_SIZE !=
4096. Rename UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE into
UFSHCD_QUIRK_4KB_DMA_ALIGNMENT.
Cc: Kiwoong Kim <kwmad.kim@samsung.com> Fixes: 2b2bfc8aa519 ("scsi: ufs: Introduce a quirk to allow only page-aligned sg entries") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
v2.5.0 support was originally added for SC7280, but this hw is also
present on SM8350, which has one more DSI host. Bump up the dsi count
and fill in the register of the secondary host to allow it to probe.
This should not have any adverse effects on SC7280, as the secondary
CTRL will only be touched if it's defined, anyway.
Fixes: 65c391b31994 ("drm/msm/dsi: Add DSI support for SC7280") Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519513/ Link: https://lore.kernel.org/r/20230120210101.2146852-1-konrad.dybcio@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MIPI DCS specification demands that brightness values are sent in
big endian byte order. It also states that one parameter (i.e. one byte)
shall be sent/received for 8 bit wide values, and two parameters shall
be used for values that are between 9 and 16 bits wide.
Add new functions to properly handle 16-bit brightness in big endian,
since the two 8- and 16-bit cases are distinct from each other.
[richard: use separate functions instead of switch/case]
[richard: split into 16-bit component]
Instead of having several fixed values for the pcr register, calculate
it before programming. This allows the bridge to support most of the
display modes.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-6-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver will reset the bridge in the atomic_pre_enable(). However
this will also drop the HPD interrupt state. Instead of resetting the
bridge, properly wake it up. This fixes the HPD interrupt delivery after
the disable/enable cycle.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-3-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
On atomic_post_disable the bridge goes to the low power state. However
the code disables too much of the chip, so the HPD event is not being
detected and delivered to the host. Reduce the power saving in order to
get the HPD event.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-2-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
In the event that the topology requests resources that have not been
created by the system (because they are typically not represented in
dpu_mdss_cfg ^1), the resource(s) in global_state (in this case DSC
blocks, until their allocation/assignment is being sanity-checked in
"drm/msm/dpu: Reject topologies for which no DSC blocks are available")
remain NULL but will still be returned out of
dpu_rm_get_assigned_resources, where the caller expects to get an array
containing num_blks valid pointers (but instead gets these NULLs).
To prevent this from happening, where null-pointer dereferences
typically result in a hard-to-debug platform lockup, num_blks shouldn't
increase past NULL blocks and will print an error and break instead.
After all, max_blks represents the static size of the maximum number of
blocks whereas the actual amount varies per platform.
^1: which can happen after a git rebase ended up moving additions to
_dpu_cfg to a different struct which has the same patch context.
Fixes: 4624459c84d7 ("drm/amdgpu: add gang submit frontend v6") Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current CLRSIPO count is still marginal and does not work with high
DSI clock rates in burst mode. Increase it further to allow the DSI link
to work at up to 1Gbps lane speed. This returns the counts to defaults
as provided by datasheet.
Initialize is_dsp_mode flag in the beginning of function
fsl_sai_set_dai_fmt_tr().
When the DAIFMT is DAIFMT_DSP_B the first time, is_dsp_mode is
true, then the second time DAIFMT is DAIFMT_I2S, is_dsp_mode
still true, which is a wrong state. So need to initialize
is_dsp_mode flag every time.
Fixes: a3f7dcc9cc03 ("ASoC: fsl-sai: Add SND_SOC_DAIFMT_DSP_A/B support.") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com> Link: https://lore.kernel.org/r/1673852874-32200-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/qla2xxx/qla_edif_bsg.h:93:12: warning: field remote_pid
within 'struct app_pinfo_req' is less aligned than 'port_id_t' and is
usually due to 'struct app_pinfo_req' being packed, which can lead to
unaligned accesses [-Wunaligned-access]
port_id_t remote_pid;
^
2 warnings generated.
Remove u32 field in remote_pid to silence warning.
In large environment, it is possible to experience command timeout and
escalation of path recovery. Currently the driver does not track the number
of exchanges/commands sent to FW. If there is a delay for commands at the
head of the queue, then this will create back pressure for commands at the
back of the queue.
Check for exchange availability before command submission.
Fixes: 0f9fa5f58c78 ("drm/panel-edp: add IVO M133NW4J-R3 panel entry") Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Steev Klimaszewski <steev@kali.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221231142721.338643-1-abel.vesa@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If worker creation fails, nullify the event_thread->worker, so that
msm_drm_uninit() doesn't try accessing invalid memory location. While we
are at it, remove duplicate assignment to the ret variable.
The back porch timings were correct, only the sync offset was wrong.
Correct timing is now reported for 1080i and 576i, but the h offset is
incorrect for 480i for non-obvious reasons.
Fixes: fb10dc451c0f ("drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-14-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same as the xRGB8888 formats, HVS5 has managed to swap the colour
channels for the xRGB1555 formats as well. Add the relevant
config for pixel_order_hvs5.
The bit used for SCALER_DISPBKGND_AUTOHS in SCALER_DISPBKGNDX
has been repurposed on HVS5 to configure whether a display can
win back-to-back arbitration wins for the COB.
This is not desirable, therefore only select this bit on HVS4,
and explicitly clear it on HVS5.
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Add check for the return value of alloc_ordered_workqueue as it may return
NULL pointer and cause NULL pointer dereference in `hdmi_hdcp.c` and
`hdmi_hpd.c`.
A user complained that the ftsteutates driver was displaying
bogus values since its introduction. This happens because the
sensor measurements need to be scaled in order to produce
meaningful results:
- the fan speed needs to be multiplied by 60 since its in RPS
- the temperature is in degrees celsius and needs an offset of 64
- the voltage is in 1/256 of 3.3V
The offical datasheet says the voltage needs to be divided by 256,
but this is likely an off-by-one-error, since even the BIOS
devides by 255 (otherwise 3.3V could not be measured).
The voltage channels additionally need a board-specific multiplier,
however this can be done by the driver since its board-specific.
The reason the missing scaling of measurements is the way Fujitsu
used this driver when it was still out-of-tree. Back then, all
scaling was done in userspace by libsensors, even the generic one.
If vc4_hdmi_reset_link() returns -EDEADLK, it means that a deadlock
happened in the locking context. This situation should be addressed by
dropping all currently held locks and block until the contended lock
becomes available. Currently, vc4 is not dealing with the deadlock
properly, producing the following output when PROVE_LOCKING is enabled:
There was a long-standing bug from a typo that created 2 ARGB1555 and
ABGR1555 pixel format entries. Weston 10 has a sanity check that alerted
me to this issue.
According to the Supported Pixel Data formats table we have the later
entries should have been for Alpha-X instead.
Signed-off-by: Randolph Sapp <rs@ti.com> Fixes: 32a1795f57eecc ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com> Acked-by: Andrew Davis <afd@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221202001803.1765805-1-rs@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason is that an OOM happened which triggers the destroy of the
workqueue, however, the workqueue is alloced in the later process,
thus a null-ptr-deref happened. A simple call graph is shown as below:
vkms_init()
vkms_create()
devm_drm_dev_alloc()
__devm_drm_dev_alloc()
devm_drm_dev_init()
devm_add_action_or_reset()
devm_add_action() # an error happened
devm_drm_dev_init_release()
drm_dev_put()
kref_put()
drm_dev_release()
vkms_release()
destroy_workqueue() # null-ptr-deref happened
vkms_modeset_init()
vkms_output_init()
vkms_crtc_init() # where the workqueue get allocated
Fix this by checking if composer_workq is NULL before passing it to
the destroy_workqueue() in vkms_release().
The reason is that the vkms_init() returns without checking the return
value of vkms_create(), and if the vkms_create() failed, the config
allocated at the beginning of vkms_init() is leaked.
vkms_init()
config = kmalloc(...) # config allocated
...
return vkms_create() # vkms_create failed and config is leaked
Fix this problem by checking return value of vkms_create() and free the
config if error happened.
A problem about insmod megachips-stdpxxxx-ge-b850v3-fw.ko failed is
triggered with the following log given:
[ 4497.981497] Error: Driver 'stdp4028-ge-b850v3-fw' is already registered, aborting...
insmod: ERROR: could not insert module megachips-stdpxxxx-ge-b850v3-fw.ko: Device or resource busy
The reason is that stdpxxxx_ge_b850v3_init() returns i2c_add_driver()
directly without checking its return value, if i2c_add_driver() failed,
it returns without calling i2c_del_driver() on the previous i2c driver,
resulting the megachips-stdpxxxx-ge-b850v3-fw can never be installed
later.
A simple call graph is shown as below:
Fix by calling i2c_del_driver() on stdp4028_ge_b850v3_fw_driver when
i2c_add_driver() returns error.
Fixes: fcfa0ddc18ed ("drm/bridge: Drivers for megachips-stdpxxxx-ge-b850v3-fw (LVDS-DP++)") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com> Tested-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221108091226.114524-1-yuancan@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Freescale/NXP i.MX LCDIF and eLCDIF LCD controllers are only present on
Freescale/NXP i.MX SoCs. Hence add a dependency on ARCH_MXS ||
ARCH_MXC, to prevent asking the user about this driver when configuring
a kernel without Freescale/NXP i.MX support.
The Freescale/NXP i.MX LCDIFv3 LCD controller is only present on
Freescale/NXP i.MX SoCs. Hence add a dependency on ARCH_MXC, to prevent
asking the user about this driver when configuring a kernel without
Freescale/NXP i.MX support.
The datasheet specifies a delay of 10 milliseconds, but the current
driver only waits for 1 ms. Fix this to make sure the initialization
sequence meets the spec.
Fixes: ceb515ba29ba ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221122081219.20143-1-frieder@fris.de Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit eae06120f1974e1a ("drm: refuse ADDFB2 ioctl for broken
bigendian drivers"), drivers must set the
quirk_addfb_prefer_host_byte_order quirk to make the drm_mode_addfb()
compat code work correctly on big-endian machines.
While that works fine for big-endian XRGB8888 and ARGB8888, which are
mapped to the existing little-endian BGRX8888 and BGRA8888 formats, it
does not work for big-endian XRGB1555 and RGB565, as the latter are not
listed in the format database.
Fix this by adding the missing formats. Limit this to big-endian
platforms, as there is currently no need to support these formats on
little-endian platforms.
drmm_mode_config_init() will call drm_mode_create_standard_properties()
and won't check the ret value. When drm_mode_create_standard_properties()
failed due to alloc, property will be a NULL pointer and may causes the
null-ptr-deref. Fix the null-ptr-deref by adding the ret value check.
Found null-ptr-deref while testing insert module bochs:
general protection fault, probably for non-canonical address
0xdffffc000000000c: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067]
CPU: 3 PID: 249 Comm: modprobe Not tainted 6.1.0-rc1+ #364
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
RIP: 0010:drm_object_attach_property+0x73/0x3c0 [drm]
Call Trace:
<TASK>
__drm_connector_init+0xb6c/0x1100 [drm]
bochs_pci_probe.cold.11+0x4cb/0x7fe [bochs]
pci_device_probe+0x17d/0x340
really_probe+0x1db/0x5d0
__driver_probe_device+0x1e7/0x250
driver_probe_device+0x4a/0x120
__driver_attach+0xcd/0x2c0
bus_for_each_dev+0x11a/0x1b0
bus_add_driver+0x3d7/0x500
driver_register+0x18e/0x320
do_one_initcall+0xc4/0x3e0
do_init_module+0x1b4/0x630
load_module+0x5dca/0x7230
__do_sys_finit_module+0x100/0x170
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7ff65af9f839
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com> Fixes: b74c37fd35a2 ("selftests: netdevsim: add tests for devlink reload with resources") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Usage of `set -e` before executing a command causes immediate exit
on failure, without cleanup up the resources allocated at setup.
This can affect the next tests that use the same resources,
leading to a chain of failures.
A simple fix is to always call cleanup function when the script exists.
This approach is already used by other existing tests.
Fixes: 1056691b2680 ("selftests: fib_tests: Make test results more verbose") Signed-off-by: Roxana Nicolescu <roxana.nicolescu@canonical.com> Link: https://lore.kernel.org/r/20230220110400.26737-2-roxana.nicolescu@canonical.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call "skb_copy_from_linear_data(skb, inl + 1, spc)" triggers a FORTIFY
memcpy() warning on ppc64 platform:
In function ‘fortify_memcpy_chk’,
inlined from ‘skb_copy_from_linear_data’ at ./include/linux/skbuff.h:4029:2,
inlined from ‘build_inline_wqe’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:722:4,
inlined from ‘mlx4_en_xmit’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:1066:3:
./include/linux/fortify-string.h:513:25: error: call to ‘__write_overflow_field’ declared with
attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()?
[-Werror=attribute-warning]
513 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Same behaviour on x86 you can get if you use "__always_inline" instead of
"inline" for skb_copy_from_linear_data() in skbuff.h
The call here copies data into inlined tx destricptor, which has 104
bytes (MAX_INLINE) space for data payload. In this case "spc" is known
in compile-time but the destination is used with hidden knowledge
(real structure of destination is different from that the compiler
can see). That cause the fortify warning because compiler can check
bounds, but the real bounds are different. "spc" can't be bigger than
64 bytes (MLX4_INLINE_ALIGN), so the data can always fit into inlined
tx descriptor. The fact that "inl" points into inlined tx descriptor is
determined earlier in mlx4_en_xmit().
Avoid confusing the compiler with "inl + 1" constructions to get to past
the inl header by introducing a flexible array "data" to the struct so
that the compiler can see that we are not dealing with an array of inl
structs, but rather, arbitrary data following the structure. There are
no changes to the structure layout reported by pahole, and the resulting
machine code is actually smaller.
When doing timestamping in lan966x and having PROVE_LOCKING
enabled the following warning is shown.
========================================================
WARNING: possible irq lock inversion dependency detected 6.2.0-rc7-01749-gc54e1f7f7e36 #2786 Tainted: G N
--------------------------------------------------------
swapper/0/0 just changed the state of lock: c2609f50 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x16c/0x2e8
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&lan966x->ptp_ts_id_lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G N 6.2.0-rc7-01749-gc54e1f7f7e36 #2786
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from mark_lock.part.0+0x59c/0x93c
mark_lock.part.0 from __lock_acquire+0x978/0x2978
__lock_acquire from lock_acquire.part.0+0xb0/0x248
lock_acquire.part.0 from _raw_spin_lock+0x38/0x48
_raw_spin_lock from sch_direct_xmit+0x16c/0x2e8
sch_direct_xmit from __dev_queue_xmit+0x41c/0x1224
__dev_queue_xmit from ip6_finish_output2+0x5f4/0xc64
ip6_finish_output2 from ndisc_send_skb+0x4cc/0x81c
ndisc_send_skb from addrconf_rs_timer+0xb0/0x2f8
addrconf_rs_timer from call_timer_fn+0xb4/0x33c
call_timer_fn from expire_timers+0xb4/0x10c
expire_timers from run_timer_softirq+0xf8/0x2a8
run_timer_softirq from __do_softirq+0xd4/0x5fc
__do_softirq from __irq_exit_rcu+0x138/0x17c
__irq_exit_rcu from irq_exit+0x8/0x28
irq_exit from __irq_svc+0x90/0xbc
Exception stack(0xc1001f20 to 0xc1001f68)
1f20: ffffffffffffffff00000001c011f840c100e000c100e000c1009314c1009370
1f40: c10f0c1ac0d5e564c0f5da8c0000000000000000c1001f70c010f0bcc010f0c0
1f60: 600f0013ffffffff
__irq_svc from arch_cpu_idle+0x30/0x3c
arch_cpu_idle from default_idle_call+0x44/0xac
default_idle_call from do_idle+0xc8/0x138
do_idle from cpu_startup_entry+0x18/0x1c
cpu_startup_entry from rest_init+0xcc/0x168
rest_init from arch_post_acpi_subsys_init+0x0/0x8
Fix this by using spin_lock_irqsave/spin_lock_irqrestore also
inside lan966x_ptp_irq_handler.
When the bcmgenet_mii_config() code was refactored it was missed
that the LED control for the MoCA interface got overwritten by
the port_ctrl value. Its previous programming is restored here.
Fixes: 4f8d81b77e66 ("net: bcmgenet: Refactor register access in bcmgenet_mii_config") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a file descriptor of pppol2tp socket is passed as file descriptor
of UDP socket, a recursive deadlock occurs in l2tp_tunnel_register().
This situation is reproduced by the following program:
int main(void)
{
int sock;
struct sockaddr_pppol2tp addr;
This patch fixes the issue by getting/creating the tunnel before
locking the pppol2tp socket.
Fixes: 0b2c59720e65 ("l2tp: close all race conditions in l2tp_tunnel_register()") Cc: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This will cause the data received by a victim connection to be cleared,
thus triggering an HTTP 400 error in the server.
This patch exchange the order between clear used and memset, add
barrier to ensure memory consistency.
Fixes: 1c5526968e27 ("net/smc: Clear memory when release and reuse buffer") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason here is that when the server tries to create a second link,
smc_llc_srv_add_link() has no protection and may add a new link to
link group. This breaks the security environment protected by
llc_conf_mutex.
Fixes: 2d2209f20189 ("net/smc: first part of add link processing as SMC server") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for the interrupt controller was added with a5042de2688d,
we forgot to update the flags to be set to contain IRQ_LEVEL. While the
flow handler is correct, the output from /proc/interrupts does not show
such interrupts as being level triggered when they are, correct that.
When support for the level triggered interrupt controller flavor was
added with c0ca7262088e, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: c0ca7262088e ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
KPROBE program's user-facing context type is defined as typedef
bpf_user_pt_regs_t. This leads to a problem when trying to passing
kprobe/uprobe/usdt context argument into global subprog, as kernel
always strip away mods and typedefs of user-supplied type, but takes
expected type from bpf_ctx_convert as is, which causes mismatch.
Current way to work around this is to define a fake struct with the same
name as expected typedef:
This patch fixes the issue by resolving expected type, if it's not
a struct. It still leaves the above work-around working for backwards
compatibility.
This patch fixes the following issue of function calls in JIT, like:
[ 29.346981] multi-func JIT bug 105 != 103
The issus can be reproduced by running the "inline simple bpf_loop call"
verifier test.
This is because we are emiting 2-4 instructions for 64-bit immediate moves.
During the first pass of JIT, the placeholder address is zero, emiting two
instructions for it. In the extra pass, the function address is in XKVRANGE,
emiting four instructions for it. This change the instruction index in
JIT context. Let's always use 4 instructions for function address in JIT.
So that the instruction sequences don't change between the first pass and
the extra pass for function calls.
Xsk Tx can be triggered via either sendmsg() or poll() syscalls. These
two paths share a call to common function xsk_xmit() which has two
sanity checks within. A pseudo code example to show the two paths:
__xsk_sendmsg() : xsk_poll():
if (unlikely(!xsk_is_bound(xs))) if (unlikely(!xsk_is_bound(xs)))
return -ENXIO; return mask;
if (unlikely(need_wait)) (...)
return -EOPNOTSUPP; xsk_xmit()
mark napi id
(...)
xsk_xmit()
xsk_xmit():
if (unlikely(!(xs->dev->flags & IFF_UP)))
return -ENETDOWN;
if (unlikely(!xs->tx))
return -ENOBUFS;
As it can be observed above, in sendmsg() napi id can be marked on
interface that was not brought up and this causes a NULL ptr
dereference:
To fix this, let's make xsk_xmit a function that will be responsible for
generic Tx, where RCU is handled accordingly and pull out sanity checks
and xs->zc handling. Populate sanity checks to __xsk_sendmsg() and
xsk_poll().
Fixes: ca2e1a627035 ("xsk: Mark napi_id on sendmsg()") Fixes: 18b1ab7aa76b ("xsk: Fix race at socket teardown") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20230215143309.13145-1-maciej.fijalkowski@intel.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Start a rework initiated by Vincents remarks "You should not report
the greatest of txerr and rxerr but the one which actually increased."
[1] and "As far as I understand, those flags should be set only when
the threshold is reached" [2] .
Therefore make use of can_change_state() to (among others) set the
flags CAN_ERR_CRTL_[RT]X_WARNING and CAN_ERR_CRTL_[RT]X_PASSIVE,
maintain CAN statistic counters for error_warning, error_passive and
bus_off.
Relocate testing alloc_can_err_skb() for NULL to the end of
esd_usb_rx_event(), to have things like can_bus_off(),
can_change_state() working even in out of memory conditions.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: [1] https://lore.kernel.org/all/CAMZ6RqKGBWe15aMkf8-QLf-cOQg99GQBebSm+1wEzTqHgvmNuw@mail.gmail.com/
Link: [2] https://lore.kernel.org/all/CAMZ6Rq+QBO1yTX_o6GV0yhdBj-RzZSRGWDZBS0fs7zbSTy4hmA@mail.gmail.com/ Link: https://lore.kernel.org/all/20230216190450.3901254-3-frank.jungclaus@esd.eu Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu> Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
s390x cache line size is 256 bytes, so skb_shared_info must be aligned
on a much larger boundary than for x86. This makes the maximum packet
size smaller.
Currently the freed element in bpf memory allocator may be immediately
reused, for htab map the reuse will reinitialize special fields in map
value (e.g., bpf_spin_lock), but lookup procedure may still access
these special fields, and it may lead to hard-lockup as shown below:
NMI backtrace for cpu 16
CPU: 16 PID: 2574 Comm: htab.bin Tainted: G L 6.1.0+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
RIP: 0010:queued_spin_lock_slowpath+0x283/0x2c0
......
Call Trace:
<TASK>
copy_map_value_locked+0xb7/0x170
bpf_map_copy_value+0x113/0x3c0
__sys_bpf+0x1c67/0x2780
__x64_sys_bpf+0x1c/0x20
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
......
</TASK>
For htab map, just like the preallocated case, these is no need to
initialize these special fields in map value again once these fields
have been initialized. For preallocated htab map, these fields are
initialized through __GFP_ZERO in bpf_map_area_alloc(), so do the
similar thing for non-preallocated htab in bpf memory allocator. And
there is no need to use __GFP_ZERO for per-cpu bpf memory allocator,
because __alloc_percpu_gfp() does it implicitly.
There's at least one case in ieee80211_rx_for_interface()
where we might pass &((struct sta_info *)NULL)->sta to it
only to then do container_of(), and then checking the
result for NULL, but checking the result of container_of()
for NULL looks really odd.
Fix this by just passing the struct sta_info * instead.
Fixes: e66b7920aa5a ("wifi: mac80211: fix initialization of rx->link and rx->link_sta") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The compiler is optimizing out majority of unref_ptr read/writes, so the test
wasn't testing much. For example, one could delete '__kptr' tag from
'struct prog_test_ref_kfunc __kptr *unref_ptr;' and the test would still "pass".
Convert it to volatile stores. Confirmed by comparing bpf asm before/after.
Fixes: 2cbc469a6fc3 ("selftests/bpf: Add C tests for kptr") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Stanislav Fomichev <sdf@google.com> Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20230214235051.22938-1-alexei.starovoitov@gmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 74c8e6bffbe1 ("driver core: Add __alloc_size hint to devm
allocators") exposes a panic "BRK handler: Fatal exception" on the
hi3660_thermal_probe funciton.
This is because the function allocates memory for only one
sensors array entry, but tries to fill up a second one.
The convention for find_first_bit() is 0-based, while ffs()
is 1-based, so this is now off-by-one. I cannot reproduce the
gcc-9 problem, but since the -1 is now removed, I'm hoping it
will still avoid the original issue.
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com> Fixes: 1d8d4af43474 ("wifi: mac80211: avoid u32_encode_bits() warning") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-9 triggers a false-postive warning in ieee80211_mlo_multicast_tx()
for u32_encode_bits(ffs(links) - 1, ...), since ffs() can return zero
on an empty bitmask, and the negative argument to u32_encode_bits()
is then out of range:
In file included from include/linux/ieee80211.h:21,
from include/net/cfg80211.h:23,
from net/mac80211/tx.c:23:
In function 'u32_encode_bits',
inlined from 'ieee80211_mlo_multicast_tx' at net/mac80211/tx.c:4437:17,
inlined from 'ieee80211_subif_start_xmit' at net/mac80211/tx.c:4485:3:
include/linux/bitfield.h:177:3: error: call to '__field_overflow' declared with attribute error: value doesn't fit into mask
177 | __field_overflow(); \
| ^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:197:2: note: in expansion of macro '____MAKE_OP'
197 | ____MAKE_OP(u##size,u##size,,)
| ^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro '__MAKE_OP'
200 | __MAKE_OP(32)
| ^~~~~~~~~
Newer compiler versions do not cause problems with the zero argument
because they do not consider this a __builtin_constant_p().
It's also harmless since the hweight16() check already guarantees
that this cannot be 0.
Replace the ffs() with an equivalent find_first_bit() check that
matches the later for_each_set_bit() style and avoids the warning.
MLD address translation should be done only for individually addressed
frames. Otherwise, AAD calculation would be wrong and the decryption
would fail.
Fixes: e66b7920aa5ac ("wifi: mac80211: fix initialization of rx->link and rx->link_sta") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Link: https://lore.kernel.org/r/20230214101048.792414-1-andrei.otcheretianski@intel.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Non-MLO station frames are dropped in Rx path due to the condition
check in ieee80211_rx_is_valid_sta_link_id(). In multi-link AP scenario,
non-MLO stations try to connect in any of the valid links in the ML AP,
where the station valid_links and link_id params are valid in the
ieee80211_sta object. But ieee80211_rx_is_valid_sta_link_id() always
return false for the non-MLO stations by the assumption taken is
valid_links and link_id are not valid in non-MLO stations object
(ieee80211_sta), this assumption is wrong. Due to this assumption,
non-MLO station frames are dropped which leads to failure in association.
Fix it by removing the condition check and allow the link validation
check for the non-MLO stations.
Fixes: e66b7920aa5a ("wifi: mac80211: fix initialization of rx->link and rx->link_sta") Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Link: https://lore.kernel.org/r/20230206160330.1613-1-quic_periyasa@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
Move color collision report in a dedicated delayed work and do not run
it in interrupt context in order to rate-limit the number of events
reported to userspace. Moreover grab wdev mutex in
ieee80211_color_collision_detection_work routine since it is required
by cfg80211_obss_color_collision_notify().
Tested-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Fixes: 5f9404abdf2a ("mac80211: add support for BSS color change") Link: https://lore.kernel.org/r/3f6cf60c892ad40c1cca4a55d62b1224ef1c6ce9.1674644379.git.lorenzo@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In crypto4xx_cipher_done, we should be unmapping the dst page, not
mapping it.
This was flagged by a sparse warning about the unused addr variable.
While we're at it, also fix a sparse warning regarding the unused
ctx variable in crypto4xx_ahash_done (by actually using it).
Fixes: 049359d65527 ("crypto: amcc - Add crypt4xx driver") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
cn10k_cpt.o, otx2_cptlf.o and otx2_cpt_mbox_common.o are linked
into both rvu_cptpf and rvu_cptvf modules:
> scripts/Makefile.build:252: ./drivers/crypto/marvell/octeontx2/Makefile:
> cn10k_cpt.o is added to multiple modules: rvu_cptpf rvu_cptvf
> scripts/Makefile.build:252: ./drivers/crypto/marvell/octeontx2/Makefile:
> otx2_cptlf.o is added to multiple modules: rvu_cptpf rvu_cptvf
> scripts/Makefile.build:252: ./drivers/crypto/marvell/octeontx2/Makefile:
> otx2_cpt_mbox_common.o is added to multiple modules: rvu_cptpf rvu_cptvf
Despite they're build under the same Kconfig option
(CONFIG_CRYPTO_DEV_OCTEONTX2_CPT), it's better do link the common
code into a standalone module and export the shared functions. Under
certain circumstances, this can lead to the same situation as fixed
by commit 637a642f5ca5 ("zstd: Fixing mixed module-builtin objects").
Plus, those three common object files are relatively big to duplicate
them several times.
Introduce the new module, rvu_cptcommon, to provide the common
functions to both modules.
Fixes: 19d8e8c7be15 ("crypto: octeontx2 - add virtual function driver support") Suggested-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Alexander Lobakin <alobakin@pm.me> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Apply commit 7592b79ba4a9 ("ACPI: resource: do IRQ override on XMG Core 15")
override for all vendors using this mainboard.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Fixes: 9946e39fe8d0 ("ACPI: resource: skip IRQ override on AMD Zen platforms") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a regression introduced by commit 9946e39fe8d0 ("ACPI: resource: skip
IRQ override on AMD Zen platforms") on MAINGEAR Vector Pro 2 systems, which
causes the built-in keyboard to not work. This restores the functionality
by adding an IRQ override.
No other IRQs were being overridden before, so this should be all that is
needed for these systems. I have personally tested this on the 15" model
(MG-VCP2-15A3070T), and I have confirmation that the issue is present on
the 17" model (MG-VCP2-17A3070T).
Fixes: 9946e39fe8d0 ("ACPI: resource: skip IRQ override on AMD Zen platforms") Signed-off-by: Adam Niederer <adam.niederer@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
make: *** No rule to make target '/linux-build//ima_setup.sh', needed by 'ima_setup.sh'. Stop.
The culprit is the rule that defines convenient shorthands like
"make test_progs", which builds $(OUTPUT)/test_progs. These shorthands
make sense only for binaries that are built though; scripts that live
in the source tree do not end up in $(OUTPUT).
Therefore drop $(TEST_PROGS) and $(TEST_PROGS_EXTENDED) from the rule.
The issue exists for a while, but it became a problem only after commit d68ae4982cb7 ("selftests/bpf: Install all required files to run selftests"),
which added dependencies on these scripts.
A static key is used to select between SBI and Sstc timer usage in
riscv_clock_next_event(), but currently the direction is resolved
after cpuhp_setup_state() is called (which sets the next event). The
first event will therefore fall through the sbi_set_timer() path; this
breaks Sstc-only systems. So, apply the jump patching before first
use.
Similarly to commit 022eb8ae8b5e ("ARM: 8938/1: kernel: initialize
broadcast hrtimer based clock event device"), RISC-V needs to initiate
hrtimer based broadcast clock event device before C3STOP can be used.
Otherwise, the introduction of C3STOP for the RISC-V arch timer in
commit 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped
during CPU suspend") leaves us without any broadcast timer registered.
This prevents the kernel from entering oneshot mode, which breaks timer
behaviour, for example clock_nanosleep().
A test app that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250
& C3STOP enabled, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/ Fixes: 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped during CPU suspend") Suggested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Anup Patel <apatel@ventanamicro.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Link: https://lore.kernel.org/r/20230103141102.772228-2-apatel@ventanamicro.com Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_PROC_FS is not set, there is a build error for an unused
function. Make PROC_HARDWARE depend on PROC_FS to prevent this error.
In file included from ../arch/m68k/kernel/setup.c:3:
../arch/m68k/kernel/setup_mm.c:477:12: error: 'hardware_proc_show' defined but not used [-Werror=unused-function]
477 | static int hardware_proc_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~~
Use the akcipher_request_complete helper instead of calling the
completion function directly. In fact the previous code was buggy
in that EINPROGRESS was never passed back to the original caller.
rds_rm_zerocopy_callback() uses list_add_tail() with swapped
arguments. This links the list head with the new entry, losing
the references to the remaining part of the list.
Fixes: 9426bbc6de99 ("rds: use list structure to track information for zerocopy completion notification") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update stub IOMMU driver (which main purpose is to reuse generic
IOMMU device-tree bindings by Xen grant DMA-mapping layer on Arm)
according to the recent changes done in the following
commit 57365a04c921 ("iommu: Move bus setup to IOMMU device registration").
With probe_device() callback being called during IOMMU device registration,
the uninitialized callback just leads to the "kernel NULL pointer
dereference" issue during boot. Fix that by adding a dummy callback.
Looks like the release_device() callback is not mandatory to be
implemented as IOMMU framework makes sure that callback is initialized
before dereferencing.
The code assumes that everything that comes after nlmsgerr are nlattrs.
When calculating their size, it does not account for the initial
nlmsghdr. This may lead to accessing uninitialized memory.
Since commit 159491f3b509 ("s390/ap: rework assembler functions to use
unions for in/out register variables") the function ap_qact() tries to
grab the status from the wrong part of the register. Thus we always end
up with zeros. Which is wrong, among others, because we detect failures
via status.response_code.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Harald Freudenberger <freude@linux.ibm.com> Fixes: 159491f3b509 ("s390/ap: rework assembler functions to use unions for in/out register variables") Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There function ap_aqic() tries to grab the status from the
wrong part of the register. Thus we always end up with
zeros. Which is wrong, among others, because we detect
failures via status.response_code.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Janosch Frank <frankja@linux.ibm.com> Fixes: 159491f3b509 ("s390/ap: rework assembler functions to use unions for in/out register variables") Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting at IPA v4.11, the GSI_GENERIC_COMMAND GSI register got a
new PARAMS field. The code that encodes a value into that field
sets it unconditionally, which is wrong.
We currently only provide 0 as the field's value, so this error has
no real effect. Still, it's a bug, so let's fix it.
Fix an (unrelated) incorrect comment as well. Fields in the
ERROR_LOG GSI register actually *are* defined for IPA versions
prior to v3.5.1.
Fixes: fe68c43ce388 ("net: ipa: support enhanced channel flow control") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bluetooth controller attached via the UART is handled by the serdev driver.
Get the wakeup status from the device handle through serdev, instead of the
parent path.
This fixes all instances of which requires to allocate a buffer calling
alloc_skb which may release the chan lock and reacquire later which
makes it possible that the chan is disconnected in the meantime.
Fixes: a6a5568c03c4 ("Bluetooth: Lock the L2CAP channel when sending") Reported-by: Alexander Coffin <alex.coffin@matician.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The compiler thinks "conn" might be NULL after a call to hci_bind_bis(),
which cannot happen. Avoid any confusion by just making it not return a
value since it cannot fail. Fixes the warnings seen with GCC 13:
In function 'arch_atomic_dec_and_test',
inlined from 'atomic_dec_and_test' at ../include/linux/atomic/atomic-instrumented.h:576:9,
inlined from 'hci_conn_drop' at ../include/net/bluetooth/hci_core.h:1391:6,
inlined from 'hci_connect_bis' at ../net/bluetooth/hci_conn.c:2124:3:
../arch/x86/include/asm/rmwcc.h:37:9: warning: array subscript 0 is outside array bounds of 'atomic_t[0]' [-Warray-bounds=]
37 | asm volatile (fullop CC_SET(cc) \
| ^~~
...
In function 'hci_connect_bis':
cc1: note: source object is likely at address zero
Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections") Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The remove function first frees the clks and only then calls
cpufreq_unregister_driver(). If one of the cpufreq callbacks is called
just before cpufreq_unregister_driver() is run, the freed clks might be
used.
Fixes: 6601b8030de3 ("davinci: add generic CPUFreq driver for DaVinci") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit ff9fb72bc077 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
projects / users / jedix / linux-maple.git / log