Recently AMT mode was enabled (somewhat unexpectedly) on the Lenovo
Z13 platform. The FW is advertising it is available and the driver tries
to use it - unfortunately it reports the profile mode incorrectly.
Note, there is also some extra work needed to enable the dynamic aspect
of AMT support that I will be following up with; but more testing is
needed first. This patch just fixes things so the profiles are reported
correctly.
acpi_get_and_request_gpiod() does not take a gpio_lookup_flags argument
specifying that the pins direction should be initialized to a specific
value.
This means that in some cases the pins might be left in input mode, causing
the gpiod_set() calls made to enable the clk / regulator to not work.
One example of this problem is the clk-enable GPIO for the ov01a1s sensor
on a Dell Latitude 9420 being left in input mode causing the clk to
never get enabled.
Explicitly set the direction of the pins to output to fix this.
Fixes: 5de691bffe57 ("platform/x86: Add intel_skl_int3472 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Reviewed-by: Daniel Scally <djrscally@gmail.com> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Link: https://lore.kernel.org/r/20230111201426.947853-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that we (the host/kernel driver) receive command messages
that are not intended for us. Ignore those for now.
The whole story is a bit more complicated: It is possible to enable
debug output on SAM, which is sent via SSH command messages. By default
this output is sent to a debug connector, with its own target ID
(TID=0x03). It is possible to override the target of the debug output
and set it to the host/kernel driver. This, however, does not change the
original target ID of the message. Meaning, we receive messages with
TID=0x03 (debug) but expect to only receive messages with TID=0x00
(host).
The problem is that the different target ID also comes with a different
scope of request IDs. In particular, these do not follow the standard
event rules (i.e. do not fall into a set of small reserved values).
Therefore, current message handling interprets them as responses to
pending requests and tries to match them up via the request ID. However,
these debug output messages are not in fact responses, and therefore
this will at best fail to find the request and at worst pass on the
wrong data as response for a request.
Therefore ignore any command messages not intended for us (host) for
now. We can implement support for the debug messages once we have a
better understanding of them.
Note that this may also provide a bit more stability and avoid some
driver confusion in case any other targets want to talk to us in the
future, since we don't yet know what to do with those as well. A warning
for the dropped messages should suffice for now and also give us a
chance of discovering new targets if they come along without any
potential for bugs/instabilities.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20221202223327.690880-2-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike keys where userspace only reacts to keypresses, userspace may act
on switches in both (0 and 1) of their positions.
For example if a SW_TABLET_MODE switch is registered then GNOME will not
automatically show the onscreen keyboard when a text field gets focus on
touchscreen devices when SW_TABLET_MODE reports 0 and when SW_TABLET_MODE
reports 1 libinput will block (filter out) builtin keyboard and touchpad
events.
So to avoid unwanted side-effects EV_SW type inputs should only be
registered if they are actually present, only register SW_CAMERA_LENS_COVER
if it is actually there.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20221221220724.119594-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patches adding NVidia-WMI-EC and Apple GMUX backlight detection
support to acpi_video_get_backlight_type(), forgot to update
acpi_video_parse_cmdline() to allow manually selecting these from
the commandline.
Add support for these to acpi_video_parse_cmdline().
Fixes: fe7aebb40d42 ("ACPI: video: Add Nvidia WMI EC brightness control detection (v3)") Fixes: 21245df307cb ("ACPI: video: Add Apple GMUX brightness control detection") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RT9120 uses PM runtime autosuspend to decrease the frequently on/off
spent time. This exists one case, when pcm is closed and dev PM is
waiting for autosuspend time expired to enter runtime suspend state.
At the mean time, system is going to enter suspend, dev PM runtime
suspend won't be called. It makes the rt9120 suspend consumption
current not as expected.
This patch can fix the rt9120 dev PM issue during runtime autosuspend
and system suspend by binding dev PM runtime and ASoC component PM.
Fixes: 80b949f332e3 ("ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic") Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> Link: https://lore.kernel.org/r/1672301033-3675-1-git-send-email-u0084500@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous commit split the hash table for polled requests into two
parts, but didn't get the fdinfo output updated. This means that it's
less useful for debugging, as we may think a given request is not pending
poll.
Fix this up by dumping the locked hash table contents too.
If session setup failed with kerberos auth, we ended up freeing
cifs_ses::auth_key.response twice in SMB2_auth_kerberos() and
sesInfoFree().
Fix this by zeroing out cifs_ses::auth_key.response after freeing it
in SMB2_auth_kerberos().
Fixes: a4e430c8c8ba ("cifs: replace kfree() with kfree_sensitive() for sensitive data") Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cifs_open_file(), @buf must hold a pointer to a cifs_open_info_data
structure which is passed by cifs_nt_open(), so assigning @buf
directly to @fi was obviously wrong.
Fix this by passing a valid FILE_ALL_INFO structure to SMBLegacyOpen()
and CIFS_open(), and then copy the set structure to the corresponding
cifs_open_info_data::fi field with move_cifs_info_to_smb2() helper.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216889 Fixes: 76894f3e2f71 ("cifs: improve symlink handling for smb2+") Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If smb311 posix is enabled, we send the intended mode for file
creation in the posix create context. Instead of using what's there on
the stack, create the mfsymlink file with 0644.
Fixes: ce558b0e17f8a ("smb3: Add posix create context for smb3.11 posix mounts") Cc: stable@vger.kernel.org Signed-off-by: Volker Lendecke <vl@samba.org> Reviewed-by: Tom Talpey <tom@talpey.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original commit 16fb4dca95daa ("drm/amdgpu: getting fan speed pwm for vega10 properly")
was reverted in commit 4545ae2ed3f2 ("drm/amdgpu: Revert "drm/amdgpu: getting fan speed pwm for vega10 properly"").
but the test that resulted in the revert was wrong and was fixed so the
revert was reverted in commit 30b8e7b8ee3b ("Revert "drm/amdgpu: Revert "drm/amdgpu: getting fan speed pwm for vega10 properly""").
That should have been the end of it, but then Sasha picked up the
original revert again and it was committed as 9ccd11718d76. So drop
that commit so we get back to where we need to be.
pipes[pipe_cnt].pipe.src.dcc_fraction_of_zs_req_luma = 0;
pipes[pipe_cnt].pipe.src.dcc_fraction_of_zs_req_chroma = 0;
these two operations in dcn32/dcn32_resource.c still need to use FPU,
This will cause compilation to fail on ARM64 platforms because
-mgeneral-regs-only is enabled by default to disable the hardware FPU.
Therefore, imitate the dcn31_zero_pipe_dcc_fraction function in
dml/dcn31/dcn31_fpu.c, declare the dcn32_zero_pipe_dcc_fraction function
in dcn32_fpu.c, and move above two operations into this function.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Ao Zhong <hacc1225@gmail.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the firmware framebuffer from the driver means that even
if the driver doesn't support the IP blocks in a GPU it will no
longer be functional after the driver fails to initialize.
This change will ensure that unsupported IP blocks at least cause
the driver to work with the EFI framebuffer.
Cc: stable@vger.kernel.org Suggested-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gem_context_register() makes the context visible to userspace, and which
point a separate thread can trigger the I915_GEM_CONTEXT_DESTROY ioctl.
So we need to ensure that nothing uses the ctx ptr after this. And we
need to ensure that adding the ctx to the xarray is the *last* thing
that gem_context_register() does with the ctx pointer.
Signed-off-by: Rob Clark <robdclark@chromium.org> Fixes: eb4dedae920a ("drm/i915/gem: Delay tracking the GEM context until it is registered") Fixes: a4c1cdd34e2c ("drm/i915/gem: Delay context creation (v3)") Fixes: 49bd54b390c2 ("drm/i915: Track all user contexts per client") Cc: <stable@vger.kernel.org> # v5.10+ Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
[tursulin: Stable and fixes tags add/tidy.] Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230103234948.1218393-1-robdclark@gmail.com
(cherry picked from commit bed4b455cf5374e68879be56971c1da563bcd90c) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A nested dma_resv_reserve_fences(1) will not reserve slot from the
2nd call onwards and folowing dma_resv_add_fence() might hit the
"BUG_ON(fobj->num_fences >= fobj->max_fences)" check.
I915 hit above nested dma_resv case in ttm_bo_handle_move_mem() with
async unbind:
dma_resv_reserve_fences() from --> ttm_bo_handle_move_mem()
dma_resv_reserve_fences() from --> i915_vma_unbind_async()
dma_resv_add_fence() from --> i915_vma_unbind_async()
dma_resv_add_fence() from -->ttm_bo_move_accel_cleanup()
Resolve this by adding an extra fence in i915_vma_unbind_async().
Suggested-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Fixes: 2f6b90da9192 ("drm/i915: Use vma resources for async unbinding") Cc: <stable@vger.kernel.org> # v5.18+ Signed-off-by: Nirmoy Das <nirmoy.das@intel.com> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221223092011.11657-1-nirmoy.das@intel.com
(cherry picked from commit 4f0755c2faf7388616109717facc5bbde6850e60) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After applying an engine reset, on some platforms like Jasperlake, we
occasionally detect that the engine state is not cleared until shortly
after the resume. As we try to resume the engine with volatile internal
state, the first request fails with a spurious CS event (it looks like
it reports a lite-restore to the hung context, instead of the expected
idle->active context switch).
We are observing performance drop in many usecases which include
games, 3D benchmark applications,etc.. To solve this problem, We
are strictly not allowing top down flag enabled allocations to
steal the memory space from cpu visible region.
The idea is, we are sorting each order list entries in
ascending order and compare the last entry of each order
list in the freelist and return the max block.
This patch improves the 3D benchmark scores and solves
fragmentation issues.
All drm buddy selftests are verfied.
drm_buddy: pass:6 fail:0 skip:0 total:6
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230112120027.3072-1-Arunpravin.PaneerSelvam@amd.com Signed-off-by: Christian König <christian.koenig@amd.com> CC: Cc: stable@vger.kernel.org # 5.18+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can guess the handle value and try to race GEM object creation
with handle close, resulting in a use-after-free if we dereference the
object after dropping the handle's reference. For that reason, dropping
the handle's reference must be done *after* we are done dereferencing
the object.
Make sure that *ptr__ within arch_this_cpu_to_op_simple() is only
dereferenced once by using READ_ONCE(). Otherwise the compiler could
generate incorrect code.
The current cmpxchg_double() loops within the perf hw sampling code do not
have READ_ONCE() semantics to read the old value from memory. This allows
the compiler to generate code which reads the "old" value several times
from memory, which again allows for inconsistencies.
The compiler could generate code where te->flags used within the
cmpxchg_double() call may be refetched from memory and which is not
necessarily identical to the previous read version which was used to
generate te_flags. Which in turn means that an incorrect update could
happen.
Fix this by adding READ_ONCE() semantics to all cmpxchg_double()
loops. Given that READ_ONCE() cannot generate code on s390 which atomically
reads 16 bytes, use a private compare-and-swap-double implementation to
achieve that.
Also replace cmpxchg_double() with the private implementation to be able to
re-use the old value within the loops.
As a side effect this converts the whole code to only use bit fields
to read and modify bits within the hws trailer header.
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.ibm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/linux-s390/Y71QJBhNTIatvxUT@osiris/T/#ma14e2a5f7aa8ed4b94b6f9576799b3ad9c60f333 Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the amd_pstate_adjust_perf(), there is one cpufreq_cpu_get() call to
increase increments the kobject reference count of policy and make it as
busy. Therefore, a corresponding call to cpufreq_cpu_put() is needed to
decrement the kobject reference count back, it will resolve the kernel
hang issue when unregistering the amd-pstate driver and register the
`amd_pstate_epp` driver instance.
Fixes: 1d215f0319 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State") Acked-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Wyes Karny <wyes.karny@amd.com> Signed-off-by: Perry Yuan <perry.yuan@amd.com> Cc: 5.17+ <stable@vger.kernel.org> # 5.17+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A subsequent fix for arm64 will use this parameter to parse the vma
information from the snapshot created by dump_vma_snapshot() rather than
traversing the vma list without the mmap_lock.
Fixes: 6dd8b1a0b6cb ("arm64: mte: Dump the MTE tags in the core file") Cc: <stable@vger.kernel.org> # 5.18.x Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Seth Jenkins <sethjenkins@google.com> Suggested-by: Seth Jenkins <sethjenkins@google.com> Cc: Will Deacon <will@kernel.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20221222181251.1345752-3-catalin.marinas@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These indices should reference the ID placed within the dai_driver
array, not the indices of the array itself.
This fixes commit 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD
lines configurable"), which among others, broke IPQ8064 audio
(sound/soc/qcom/lpass-ipq806x.c) because it uses ID 4 but we'd stop
initializing the mi2s_playback_sd_mode and mi2s_capture_sd_mode arrays
at ID 0.
Fixes: 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD lines configurable") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20221231061545.2110253-1-computersforpeace@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The introduction of support for Apple board types inadvertently changed
the precedence order, causing hybrid SMBIOS+DT platforms to look up the
firmware using the DMI information instead of the device tree compatible
to generate the board type. Revert back to the old behavior,
as affected platforms use firmwares named after the DT compatible.
Fixes: 7682de8b3351 ("wifi: brcmfmac: of: Fetch Apple properties")
[1] https://bugzilla.opensuse.org/show_bug.cgi?id=1206697#c13
Cc: stable@vger.kernel.org Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Reviewed-by: Hector Martin <marcan@marcan.st> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses the following erroneous situation with file-based
kdump executed on a system with a valid IPL report.
On s390, a kdump kernel, its initrd and IPL report if present are loaded
into a special and reserved on boot memory region - crashkernel. When
a system crashes and kdump was activated before, the purgatory code
is entered first which swaps the crashkernel and [0 - crashkernel size]
memory regions. Only after that the kdump kernel is entered. For this
reason, the pointer to an IPL report in lowcore must point to the IPL report
after the swap and not to the address of the IPL report that was located in
crashkernel memory region before the swap. Failing to do so, makes the
kdump's decompressor try to read memory from the crashkernel memory region
which already contains the production's kernel memory.
The situation described above caused spontaneous kdump failures/hangs
on systems where the Secure IPL is activated because on such systems
an IPL report is always present. In that case kdump's decompressor tried
to parse an IPL report which frequently lead to illegal memory accesses
because an IPL report contains addresses to various data.
Cc: <stable@vger.kernel.org> Fixes: 99feaa717e55 ("s390/kexec_file: Create ipl report and pass to next kernel") Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
$ gcc -Wall -Wextra -o test file1.c file2.c
$ perf record -e intel_pt//u --filter 'filter func @ ./test' -- ./test
Multiple symbols with name 'func'
#1 0x1149 l func
which is near main
#2 0x1179 l func
which is near other
Disambiguate symbol name by inserting #n after the name e.g. func #2
Or select a global symbol by inserting #0 or #g or #G
Failed to parse address filter: 'filter func @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
Failed to parse address filter: 'filter func #2 @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
Add timeout polling wait for auxiliary timestamps snapshot FIFO clear bit
(ATSFC) to clear. This is to ensure no residue fifo value is being read
erroneously.
Fixes: f4da56529da6 ("net: stmmac: Add support for external trigger timestamping") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com> Link: https://lore.kernel.org/r/20230111050200.2130-1-noor.azura.ahmad.tarmizi@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Latitude E6430 both with and without the optional NVidia dGPU
has a bug in its ACPI tables which is causing Linux to assign the wrong
ACPI fwnode / companion to the pci_device for the i915 iGPU.
Specifically under the PCI root bridge there are these 2 ACPI Device()s :
The non-functional GFX0 ACPI device is a problem, because this gets
returned as ACPI companion-device by acpi_find_child_device() for the iGPU.
This is a long standing problem and the i915 driver does use the ACPI
companion for some things, but works fine without it.
However since commit 63f534b8bad9 ("ACPI: PCI: Rework acpi_get_pci_dev()")
acpi_get_pci_dev() relies on the physical-node pointer in the acpi_device
and that is set on the wrong acpi_device because of the wrong
acpi_find_child_device() return. This breaks the ACPI video code,
leading to non working backlight control in some cases.
Add a type.backlight flag, mark ACPI video bus devices with this and make
find_child_checks() return a higher score for children with this flag set,
so that it picks the right companion-device.
Fixes: 63f534b8bad9 ("ACPI: PCI: Rework acpi_get_pci_dev()") Co-developed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: 6.1+ <stable@vger.kernel.org> # 6.1+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline assembly for arm64's cmpxchg_double*() implementations use a
+Q constraint to hazard against other accesses to the memory location
being exchanged. However, the pointer passed to the constraint is a
pointer to unsigned long, and thus the hazard only applies to the first
8 bytes of the location.
GCC can take advantage of this, assuming that other portions of the
location are unchanged, leading to a number of potential problems.
This is similar to what we fixed back in commit:
fee960bed5e857eb ("arm64: xchg: hazard against entire exchange variable")
... but we forgot to adjust cmpxchg_double*() similarly at the same
time.
The same problem applies, as demonstrated with the following test:
Notice that at the lines with "BANG" comments, GCC has assumed that the
higher 8 bytes are unchanged by the cmpxchg_double() call, and that
`hi_old ^ hi_new` can be reduced to a constant zero, for both LSE and
LL/SC versions of cmpxchg_double().
This patch fixes the issue by passing a pointer to __uint128_t into the
+Q constraint, ensuring that the compiler hazards against the entire 16
bytes being modified.
With this change, GCC 12.1.0 compiles the above test as:
... sampling the high 8 bytes before and after the cmpxchg, and
performing an EOR, as we'd expect.
For backporting, I've tested this atop linux-4.9.y with GCC 5.5.0. Note
that linux-4.9.y is oldest currently supported stable release, and
mandates GCC 5.1+. Unfortunately I couldn't get a GCC 5.1 binary to run
on my machines due to library incompatibilities.
I've also used a standalone test to check that we can use a __uint128_t
pointer in a +Q constraint at least as far back as GCC 4.8.5 and LLVM
3.9.1.
The MTE coredump code in arch/arm64/kernel/elfcore.c iterates over the
vma list without the mmap_lock held. This can race with another process
or userfaultfd concurrently modifying the vma list. Change the
for_each_mte_vma macro and its callers to instead use the vma snapshot
taken by dump_vma_snapshot() and stored in the cprm object.
Fixes: 6dd8b1a0b6cb ("arm64: mte: Dump the MTE tags in the core file") Cc: <stable@vger.kernel.org> # 5.18.x Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Seth Jenkins <sethjenkins@google.com> Suggested-by: Seth Jenkins <sethjenkins@google.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20221222181251.1345752-4-catalin.marinas@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 16decce22efa ("arm64: mte: Fix the stack frame size warning in
mte_dump_tag_range()") moved the temporary tag storage array from the
stack to slab but it also introduced an error in double freeing this
object. Remove the in-loop freeing.
Fixes: 16decce22efa ("arm64: mte: Fix the stack frame size warning in mte_dump_tag_range()") Cc: <stable@vger.kernel.org> # 5.18.x Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Seth Jenkins <sethjenkins@google.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20221222181251.1345752-2-catalin.marinas@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sphinx 6.0 removed the execfile_() function, which we use as part of the
configuration process. They *did* warn us... Just open-code the
functionality as is done in Sphinx itself.
Tested (using SPHINX_CONF, since this code is only executed with an
alternative config file) on various Sphinx versions from 2.5 through 6.0.
Reported-by: Martin Liška <mliska@suse.cz> Cc: stable@vger.kernel.org Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan reports that recent kernels built with LTO will crash when doing
EFI boot using Fedora's GRUB and SHIM. The culprit turns out to be a
misaligned load from the TPM event log, which is annotated with
READ_ONCE(), and under LTO, this gets translated into a LDAR instruction
which does not tolerate misaligned accesses.
Interestingly, this does not happen when booting the same kernel
straight from the UEFI shell, and so the fact that the event log may
appear misaligned in memory may be caused by a bug in GRUB or SHIM.
However, using READ_ONCE() to access firmware tables is slightly unusual
in any case, and here, we only need to ensure that 'event' is not
dereferenced again after it gets unmapped, but this is already taken
care of by the implicit barrier() semantics of the early_memunmap()
call.
Cc: <stable@vger.kernel.org> Cc: Peter Jones <pjones@redhat.com> Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Reported-by: Nathan Chancellor <nathan@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Link: https://github.com/ClangBuiltLinux/linux/issues/1782 Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After [1][2], if we catch exceptions due to EFI runtime service, we will
clear EFI_RUNTIME_SERVICES bit to disable EFI runtime service, then the
subsequent routine which invoke the EFI runtime service should fail.
But the userspace cat efivars through /sys/firmware/efi/efivars/ will stuck
and infinite loop calling read() due to efivarfs_file_read() return -EINTR.
The -EINTR is converted from EFI_ABORTED by efi_status_to_err(), and is
an improper return value in this situation, so let virt_efi_xxx() return
EFI_DEVICE_ERROR and converted to -EIO to invoker.
A recent development on the EFI front has resulted in guests having
their page tables baked in the firmware binary, and mapped into the
IPA space as part of a read-only memslot. Not only is this legitimate,
but it also results in added security, so thumbs up.
It is possible to take an S1PTW translation fault if the S1 PTs are
unmapped at stage-2. However, KVM unconditionally treats S1PTW as a
write to correctly handle hardware AF/DB updates to the S1 PTs.
Furthermore, KVM injects an exception into the guest for S1PTW writes.
In the aforementioned case this results in the guest taking an abort
it won't recover from, as the S1 PTs mapping the vectors suffer from
the same problem.
So clearly our handling is... wrong.
Instead, switch to a two-pronged approach:
- On S1PTW translation fault, handle the fault as a read
- On S1PTW permission fault, handle the fault as a write
This is of no consequence to SW that *writes* to its PTs (the write
will trigger a non-S1PTW fault), and SW that uses RO PTs will not
use HW-assisted AF/DB anyway, as that'd be wrong.
Only in the case described in c4ad98e4b72c ("KVM: arm64: Assume write
fault on S1PTW permission fault on instruction fetch") do we end-up
with two back-to-back faults (page being evicted and faulted back).
I don't think this is a case worth optimising for.
Fixes: c4ad98e4b72c ("KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch") Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Regression-tested-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing the host topology to the guest is almost certainly wrong
and will confuse the scheduler. In addition, several fields of
these CPUID leaves vary on each processor; it is simply impossible to
return the right values from KVM_GET_SUPPORTED_CPUID in such a way that
they can be passed to KVM_SET_CPUID2.
The values that will most likely prevent confusion are all zeroes.
Userspace will have to override it anyway if it wishes to present a
specific topology to the guest.
Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HP Spectre x360 13-aw0xxx devices use the ALC285 codec with GPIO 0x04
controlling the micmute LED and COEF 0x0b index 8 controlling the mute LED.
A quirk was added to make these work as well as a fixup.
The commit caused a regression on Behringer UMC404HD (and likely
others). As the change was meant only as a minor optimization, it's
better to revert it to address the regression.
If the offset + length goes over the ethernet + vlan header, then the
length is adjusted to copy the bytes that are within the boundaries of
the vlan_ethhdr scratchpad area. The remaining bytes beyond ethernet +
vlan header are copied directly from the skbuff data area.
Fix incorrect arithmetic operator: subtract, not add, the size of the
vlan header in case of double-tagged packets to adjust the length
accordingly to address CVE-2023-0179.
The runtime PM core checks with runtime_idle callback whether it can
goes to the runtime suspend or not, and we can put the boost type
check there instead of runtime_suspend and _resume calls. This will
reduce the unnecessary runtime_suspend() calls.
There is another Dell Latitude laptop (1028:0c03) with Realtek
codec ALC3254 which needs the ALC269_FIXUP_DELL4_MIC_NO_PRESENCE
instead of the default matched ALC269_FIXUP_DELL1_MIC_NO_PRESENCE.
Apply correct fixup for this particular model to enable headset mic.
The recent commit to support the system suspend for CS35L41 caused a
regression on the models with CS35L41_EXT_BOOST_NO_VSPK_SWITC boost
type, as the suspend/resume callbacks just return -EINVAL. This is
eventually handled as a fatal error and blocks the whole system
suspend/resume.
For avoiding the problem, this patch corrects the return code from
cs35l41_system_suspend() and _resume() to 0, and replace dev_err()
with dev_err_once() for stop spamming too much.
Takes rwsem lock inside snd_ctl_elem_read instead of snd_ctl_elem_read_user
like it was done for write in commit 1fa4445f9adf1 ("ALSA: control - introduce
snd_ctl_notify_one() helper"). Doing this way we are also fixing the following
locking issue happening in the compat path which can be easily triggered and
turned into an use-after-free.
While experimenting with applying noqueue to a classful queue discipline,
we discovered a NULL pointer dereference in the __dev_queue_xmit()
path that generates a kernel OOPS:
Previously in commit d66d6c3152e8 ("net: sched: register noqueue
qdisc"), NULL was set for the noqueue discipline on noqueue init
so that __dev_queue_xmit() falls through for the noqueue case. This
also sets a bypass of the enqueue NULL check in the
register_qdisc() function for the struct noqueue_disc_ops.
Classful queue disciplines make it past the NULL check in
__dev_queue_xmit() because the discipline is set to htb (in this case),
and then in the call to __dev_xmit_skb(), it calls into htb_enqueue()
which grabs a leaf node for a class and then calls qdisc_enqueue() by
passing in a queue discipline which assumes ->enqueue() is not set to NULL.
Fix this by not allowing classes to be assigned to the noqueue
discipline. Linux TC Notes states that classes cannot be set to
the noqueue discipline. [1] Let's enforce that here.
We had already disabled this warning for gcc-12 due to bugs in the value
range analysis, but it turns out we end up having some similar problems
with gcc-11.3 too, so let's disable it there too.
Older gcc versions end up being increasingly less relevant, and
hopefully clang and newer version of gcc (ie gcc-13) end up working
reliably enough that we still get the build coverage even when we
disable this for some versions.
The premise that "Once an svc thread is scheduled and executing an
RPC, no other processes will touch svc_rqst::rq_flags" is false.
svc_xprt_enqueue() examines the RQ_BUSY flag in scheduled nfsd
threads when determining which thread to wake up next.
Found via KCSAN.
Fixes: 28df0988815f ("SUNRPC: Use RMW bitops in single-threaded hot paths") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware XRSTOR instruction resets the PKRU register to its hardware
init value (namely 0) if the PKRU bit is not set in the xfeatures mask.
Emulating that here restores the pre-5.14 behavior for PTRACE_SET_REGSET
with NT_X86_XSTATE, and makes sigreturn (which still uses XRSTOR) and
ptrace behave identically. KVM has never used XRSTOR and never had this
behavior, so KVM opts-out of this emulation by passing a NULL pkru pointer
to copy_uabi_to_xstate().
Fixes: e84ba47e313d ("x86/fpu: Hook up PKRU into ptrace()") Signed-off-by: Kyle Huey <me@kylehuey.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lore.kernel.org/all/20221115230932.7126-6-khuey%40kylehuey.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move KVM's PKRU handling code in fpu_copy_uabi_to_guest_fpstate() to
copy_uabi_to_xstate() so that it is shared with other APIs that write the
XSTATE such as PTRACE_SETREGSET with NT_X86_XSTATE.
This restores the pre-5.14 behavior of ptrace. The regression can be seen
by running gdb and executing `p $pkru`, `set $pkru = 42`, and `p $pkru`.
On affected kernels (5.14+) the write to the PKRU register (which gdb
performs through ptrace) is ignored.
[ dhansen: removed stable@ tag for now. The ABI was broken for long
enough that this is not urgent material. Let's let it stew
in tip for a few weeks before it's submitted to stable
because there are so many ABIs potentially affected. ]
Fixes: e84ba47e313d ("x86/fpu: Hook up PKRU into ptrace()") Signed-off-by: Kyle Huey <me@kylehuey.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lore.kernel.org/all/20221115230932.7126-5-khuey%40kylehuey.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for moving PKRU handling code out of
fpu_copy_uabi_to_guest_fpstate() and into copy_uabi_to_xstate(), add an
argument that copy_uabi_from_kernel_to_xstate() can use to pass the
canonical location of the PKRU value. For
copy_sigframe_from_user_to_xstate() the kernel will actually restore the
PKRU value from the fpstate, but pass in the thread_struct's pkru location
anyways for consistency.
Both KVM (through KVM_SET_XSTATE) and ptrace (through PTRACE_SETREGSET
with NT_X86_XSTATE) ultimately call copy_uabi_from_kernel_to_xstate(),
but the canonical locations for the current PKRU value for KVM guests
and processes in a ptrace stop are different (in the kvm_vcpu_arch and
the thread_state structs respectively).
In preparation for eventually handling PKRU in
copy_uabi_to_xstate, pass in a pointer to the PKRU location.
Adjust some MADV_XXX constants to be in sync what their values are on
all other platforms. There is currently no reason to have an own
numbering on parisc, but it requires workarounds in many userspace
sources (e.g. glibc, qemu, ...) - which are often forgotten and thus
introduce bugs and different behaviour on parisc.
A wrapper avoids an ABI breakage for existing userspace applications by
translating any old values to the new ones, so this change allows us to
move over all programs to the new ABI over time.
Instead of blindly creating the EFI random seed configuration table if
the RNG protocol is implemented and works, check whether such a EFI
configuration table was provided by an earlier boot stage and if so,
concatenate the existing and the new seeds, leaving it up to the core
code to mix it in and credit it the way it sees fit.
This can be used for, e.g., systemd-boot, to pass an additional seed to
Linux in a way that can be consumed by the kernel very early. In that
case, the following definitions should be used to pass the seed to the
EFI stub:
struct linux_efi_random_seed {
u32 size; // of the 'seed' array in bytes
u8 seed[];
};
The memory for the struct must be allocated as EFI_ACPI_RECLAIM_MEMORY
pool memory, and the address of the struct in memory should be installed
as a EFI configuration table using the following GUID:
Note that doing so is safe even on kernels that were built without this
patch applied, but the seed will simply be overwritten with a seed
derived from the EFI RNG protocol, if available. The recommended seed
size is 32 bytes, and seeds larger than 512 bytes are considered
corrupted and ignored entirely.
In order to preserve forward secrecy, seeds from previous bootloaders
are memzero'd out, and in order to preserve memory, those older seeds
are also freed from memory. Freeing from memory without first memzeroing
is not safe to do, as it's possible that nothing else will ever
overwrite those pages used by EFI.
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
[ardb: incorporate Jason's followup changes to extend the maximum seed
size on the consumer end, memzero() it and drop a needless printk] Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from ICL, the default for MIPI GPIO sequences seems to be using
native GPIOs i.e. GPIOs available in the GPU. These native GPIOs reuse
many pins that quite frankly seem scary to poke based on the VBT
sequences. We pretty much have to trust that the board is configured
such that the relevant HPD, PP_CONTROL and GPIO bits aren't used for
anything else.
MIPI sequence v4 also adds a flag to fall back to non-native sequences.
v5:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock() in icp_irq_handler()
too (Ville)
- References instead of Closes issue 6131 because this does not fix everything
v4:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock_irq() (Ville)
v3:
- Fix -Wbitwise-conditional-parentheses (kernel test robot <lkp@intel.com>)
v2:
- Fix HPD pin output set (impacts GPIOs 0 and 5)
- Fix GPIO data output direction set (impacts GPIOs 4 and 9)
- Reduce register accesses to single intel_de_rwm()
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6131 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221219105955.4014451-1-jani.nikula@intel.com
(cherry picked from commit f087cfe6fcff58044f7aa3b284965af47f472fb0) Cc: stable@vger.kernel.org # 6.1 Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"nt_len - CIFS_ENCPWD_SIZE" is passed directly from
ksmbd_decode_ntlmssp_auth_blob to ksmbd_auth_ntlmv2. Malicious requests
can set nt_len to less than CIFS_ENCPWD_SIZE, which results in a negative
number (or large unsigned value) used for a subsequent memcpy in
ksmbd_auth_ntlvm2 and can cause a panic.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Cc: stable@vger.kernel.org Signed-off-by: William Liu <will@willsroot.io> Signed-off-by: Hrvoje Mišetić <misetichrvoje@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, smb2_tree_connect doesn't send an error response packet on
error.
This causes libsmb2 to skip the specific error code and fail with the
following:
smb2_service failed with : Failed to parse fixed part of command
payload. Unexpected size of Error reply. Expected 9, got 8
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kernel_recvmsg() return -EAGAIN in ksmbd_tcp_readv() and go round
again, It will cause infinite loop issue. And all threads from next
connections would be doing that. This patch add max retry count(2) to
avoid it. kernel_recvmsg() will wait during 7sec timeout and try to
retry two time if -EAGAIN is returned. And add flags of kvmalloc to
__GFP_NOWARN and __GFP_NORETRY to disconnect immediately without
retrying on memory alloation failure.
Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18259 Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
There is a bug report that a BUG_ON() in btrfs_repair_io_failure()
(originally repair_io_failure() in v6.0 kernel) got triggered when
replacing a unreliable disk:
Before the BUG_ON(), we got some read errors from the replace target
first, note the mirror number (3, which is beyond RAID1 duplication,
thus it's read from the replace target device).
Then at the BUG_ON() location, we are trying to writeback the repaired
sectors back the failed device.
The check looks like this:
ret = btrfs_map_block(fs_info, BTRFS_MAP_WRITE, logical,
&map_length, &bioc, mirror_num);
if (ret)
goto out_counter_dec;
BUG_ON(mirror_num != bioc->mirror_num);
But inside btrfs_map_block(), we can modify bioc->mirror_num especially
for dev-replace:
Thus if we're repairing the replace target device, we're going to
trigger that BUG_ON().
But in reality, the read failure from the replace target device may be
that, our replace hasn't reached the range we're reading, thus we're
reading garbage, but with replace running, the range would be properly
filled later.
Thus in that case, we don't need to do anything but let the replace
routine to handle it.
[FIX]
Instead of a BUG_ON(), just skip the repair if we're repairing the
device replace target device.
[WHY?]
Some configurations are constructed with very marginal DET buffers relative to
the worst possible time required to fetch a swath.
[HOW?]
Add a check to see that the DET buffer allocated for each pipe can hide the
latency for all pipes to fetch at least one swath.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Brian Chang <Brian.Chang@amd.com> Signed-off-by: Dillon Varone <Dillon.Varone@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: f3c23bea598a ("drm/amd/display: Uninitialized variables causing 4k60 UCLK to stay at DPM1 and not DPM0") Signed-off-by: Sasha Levin <sashal@kernel.org>
The virtblk_map_data() function returns negative error codes, however, the
'nents' field of vbr->sg_table is an unsigned int, which causes the error
handling not to work correctly.
Cc: stable@vger.kernel.org Fixes: 0e9911fa768f ("virtio-blk: support mq_ops->queue_rqs()") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Message-Id: <20221021204126.927603-1-rafaelmendsr@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Suwan Kim <suwan.kim027@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check carefully on root debugfs available when destroying vgpu,
e.g in remove case drm minor's debugfs root might already be destroyed,
which led to kernel oops like below.
When gvt debug fs is destroyed, need to have a sane check if drm
minor's debugfs root is still available or not, otherwise in case like
device remove through unbinding, drm minor's debugfs directory has
already been removed, then intel_gvt_debugfs_clean() would act upon
dangling pointer like below oops.
If memory has been found early_init_dt_scan_memory now returns 1. If
it hasn't found any memory it will return 0, allowing other memory
setup mechanisms to carry on.
Previously early_init_dt_scan_memory always returned 0 without
distinguishing between any kind of memory setup being done or not. Any
code path after the early_init_dt_scan memory call in the ramips
plat_mem_setup code wouldn't be executed anymore. Making
early_init_dt_scan_memory the only way to initialize the memory.
Some boards, including my mt7621 based Cudy X6 board, depend on memory
initialization being done via the soc_info.mem_detect function
pointer. Those wouldn't be able to obtain memory and panic the kernel
during early bootup with the message "early_init_dt_alloc_memory_arch:
Failed to allocate 12416 bytes align=0x40".
Fixes: 1f012283e936 ("of/fdt: Rework early_init_dt_scan_memory() to call directly") Cc: stable@vger.kernel.org Signed-off-by: Andreas Rammhold <andreas@rammhold.de> Link: https://lore.kernel.org/r/20221223112748.2935235-1-andreas@rammhold.de Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the get_user(x, ptr) has x as a pointer, then the setting
of (x) = 0 is going to produce the following sparse warning,
so fix this by forcing the type of 'x' when access_ok() fails.
fs/aio.c:2073:21: warning: Using plain integer as NULL pointer
While testing in vIOMMU, sometimes Guest will unmap very large memory,
which will cause the crash. To fix this, add a new function
vhost_vdpa_general_unmap(). This function will only unmap the memory
that saved in iotlb.
TPM 1 is sometimes broken across system suspends, due to races or
locking issues or something else that haven't been diagnosed or fixed
yet, most likely having to do with concurrent reads from the TPM's
hardware random number generator driver. These issues prevent the system
from actually suspending, with errors like:
tpm tpm0: A TPM error (28) occurred continue selftest
...
tpm tpm0: A TPM error (28) occurred attempting get random
...
tpm tpm0: Error (28) sending savestate before suspend
tpm_tis 00:08: PM: __pnp_bus_suspend(): tpm_pm_suspend+0x0/0x80 returns 28
tpm_tis 00:08: PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 28
tpm_tis 00:08: PM: failed to suspend: error 28
PM: Some devices failed to suspend, or early wake event detected
This issue was partially fixed by 23393c646142 ("char: tpm: Protect
tpm_pm_suspend with locks"), in a last minute 6.1 commit that Linus took
directly because the TPM maintainers weren't available. However, it
seems like this just addresses the most common cases of the bug, rather
than addressing it entirely. So there are more things to fix still,
apparently.
In lieu of actually fixing the underlying bug, just allow system suspend
to continue, so that laptops still go to sleep fine. Later, this can be
reverted when the real bug is fixed.
Link: https://lore.kernel.org/lkml/7cbe96cf-e0b5-ba63-d1b4-f63d2e826efa@suse.cz/ Cc: stable@vger.kernel.org # 6.1+ Reported-by: Vlastimil Babka <vbabka@suse.cz> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Luigi Semenzato <semenzato@chromium.org> Cc: Peter Huewe <peterhuewe@gmx.de> Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Johannes Altmanninger <aclopte@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiffy to ktime CQ waiting conversion broke how we treat timeouts, in
particular we rearm it anew every time we get into
io_cqring_wait_schedule() without adjusting the timeout. Waiting for 2
CQEs and getting a task_work in the middle may double the timeout value,
or even worse in some cases task may wait indefinitely.
Unlike normal tw, nothing prevents deferred tw to be executed right
after an tw item added to ->work_llist in io_req_local_work_add(). For
instance, the waiting task may get waken up by CQ posting or a normal
tw. Thus we need to pin the ring for the rest of io_req_local_work_add()
If we split a bio marked with REQ_NOWAIT, then we can trigger spurious
EAGAIN if constituent parts of that split bio end up failing request
allocations. Parts will complete just fine, but just a single failure
in one of the chained bios will yield an EAGAIN final result for the
parent bio.
Return EAGAIN early if we end up needing to split such a bio, which
allows for saner recovery handling.
It was discovered that MGMT_DATA2 can contain up to 28 bytes of data
instead of the 12 bytes written in the Documentation by accounting the
limit of 16 bytes declared in Documentation subtracting the first 4 byte
in the packet header.
Update the define with the real world value.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com> Fixes: c2ee8181fddb ("net: dsa: tag_qca: add define for handling mgmt Ethernet packet") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Cc: stable@vger.kernel.org # v5.18+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Tested-by: Ronald Wahl <ronald.wahl@raritan.com> Fixes: 90386223f44e ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Cc: stable@vger.kernel.org # v5.18+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Cc: stable@vger.kernel.org # v5.18+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the scenario where livepatch and kretfunc coexist, the pageattr of
im->image is rox after arch_prepare_bpf_trampoline in
bpf_trampoline_update, and then modify_fentry or register_fentry returns
-EAGAIN from bpf_tramp_ftrace_ops_func, the BPF_TRAMP_F_ORIG_STACK flag
will be configured, and arch_prepare_bpf_trampoline will be re-executed.
At this time, because the pageattr of im->image is rox,
arch_prepare_bpf_trampoline will read and write im->image, which causes
a fault. as follows:
With this patch, when modify_fentry or register_fentry returns -EAGAIN
from bpf_tramp_ftrace_ops_func, the pageattr of im->image will be reset
to nx+rw.
Cc: stable@vger.kernel.org Fixes: 00963a2e75a8 ("bpf: Support bpf_trampoline on functions with IPMODIFY (e.g. livepatch)") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20221224133146.780578-1-nashuiliang@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 62d89a7d49af ("video: fbdev: matroxfb: set maxvram of vbG200eW to
the same as vbG200 to avoid black screen") accidently decreases the
maximum memory size for the Matrox G200eW (102b:0532) from 8 MB to 1 MB
by missing one zero. This caused the driver initialization to fail with
the messages below, as the minimum required VRAM size is 2 MB:
So, add the missing 0 to make it the intended 16 MB. Successfully tested on
the Dell PowerEdge R910/0KYD3D, BIOS 2.10.0 08/29/2013, that the warning is
gone.
While at it, add a leading 0 to the maxdisplayable entry, so it’s aligned
properly. The value could probably also be increased from 8 MB to 16 MB, as
the G200 uses the same values, but I have not checked any datasheet.
Note, matroxfb is obsolete and superseded by the maintained DRM driver
mga200, which is used by default on most systems where both drivers are
available. Therefore, on most systems it was only a cosmetic issue.
Fixes: 62d89a7d49af ("video: fbdev: matroxfb: set maxvram of vbG200eW to the same as vbG200 to avoid black screen") Link: https://lore.kernel.org/linux-fbdev/972999d3-b75d-5680-fcef-6e6905c52ac5@suse.de/T/#mb6953a9995ebd18acc8552f99d6db39787aec775 Cc: it+linux-fbdev@molgen.mpg.de Cc: Z. Liu <liuzx@knownsec.com> Cc: Rich Felker <dalias@libc.org> Cc: stable@vger.kernel.org Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If v4 READDIR operation hits a mountpoint and gets back an error,
then it will include that entry in the reply and set RDATTR_ERROR for it
to the error.
That's fine for "normal" exported filesystems, but on the v4root, we
need to be more careful to only expose the existence of dentries that
lead to exports.
If the mountd upcall times out while checking to see whether a
mountpoint on the v4root is exported, then we have no recourse other
than to fail the whole operation.
Cc: Steve Dickson <steved@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216777 Reported-by: JianHong Yin <yin-jianhong@163.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log