Wolfram Sang [Tue, 9 May 2023 07:48:17 +0000 (09:48 +0200)]
drm: rcar-du: remove R-Car H3 ES1.* workarounds
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC and prevent booting it. Public users only have ES2 onwards.
Dave Airlie [Sun, 28 May 2023 20:21:50 +0000 (06:21 +1000)]
Merge tag 'drm-intel-gt-next-2023-05-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
- New getparam for querying PXP support and load status
Cross-subsystem Changes:
- GSC/MEI proxy driver
Driver Changes:
Fixes/improvements/new stuff:
- Avoid clearing pre-allocated framebuffers with the TTM backend (Nirmoy Das)
- Implement framebuffer mmap support (Nirmoy Das)
- Disable sampler indirect state in bindless heap (Lionel Landwerlin)
- Avoid out-of-bounds access when loading HuC (Lucas De Marchi)
- Actually return an error if GuC version range check fails (John Harrison)
- Get mutex and rpm ref just once in hwm_power_max_write (Ashutosh Dixit)
- Disable PL1 power limit when loading GuC firmware (Ashutosh Dixit)
- Block in hwmon while waiting for GuC reset to complete (Ashutosh Dixit)
- Provide sysfs for SLPC efficient freq (Vinay Belgaumkar)
- Add support for total context runtime for GuC back-end (Umesh Nerlige Ramappa)
- Enable fdinfo for GuC backends (Umesh Nerlige Ramappa)
- Don't capture Gen8 regs on Xe devices (John Harrison)
- Fix error capture for virtual engines (John Harrison)
- Track patch level versions on reduced version firmware files (John Harrison)
- Decode another GuC load failure case (John Harrison)
- GuC loading and firmware table handling fixes (John Harrison)
- Fix confused register capture list creation (John Harrison)
- Dump error capture to kernel log (John Harrison)
- Dump error capture to dmesg on CTB error (John Harrison)
- Disable rps_boost debugfs when SLPC is used (Vinay Belgaumkar)
Future platform enablement:
- Disable stolen memory backed FB for A0 [mtl] (Nirmoy Das)
- Various refactors for multi-tile enablement (Andi Shyti, Tejas Upadhyay)
- Extend Wa_22011802037 to MTL A-step (Madhumitha Tolakanahalli Pradeep)
- WA to clear RDOP clock gating [mtl] (Haridhar Kalvala)
- Set has_llc=0 [mtl] (Fei Yang)
- Define MOCS and PAT tables for MTL (Madhumitha Tolakanahalli Pradeep)
- Add PTE encode function [mtl] (Fei Yang)
- fix mocs selftest [mtl] (Fei Yang)
- Workaround coherency issue for Media [mtl] (Fei Yang)
- Add workaround 14018778641 [mtl] (Tejas Upadhyay)
- Implement Wa_14019141245 [mtl] (Radhakrishna Sripada)
- Fix the wa number for Wa_22016670082 [mtl] (Radhakrishna Sripada)
- Use correct huge page manager for MTL (Jonathan Cavitt)
- GSC/MEI support for Meteorlake (Alexander Usyskin, Daniele Ceraolo Spurio)
- Define GuC firmware version for MTL (John Harrison)
- Drop FLAT CCS check [mtl] (Pallavi Mishra)
- Add MTL for remapping CCS FBs [mtl] (Clint Taylor)
- Meteorlake PXP enablement (Alan Previn)
- Do not enable render power-gating on MTL (Andrzej Hajda)
- Add MTL performance tuning changes (Radhakrishna Sripada)
- Extend Wa_16014892111 to MTL A-step (Radhakrishna Sripada)
- PMU multi-tile support (Tvrtko Ursulin)
- End support for set caching ioctl [mtl] (Fei Yang)
Driver refactors:
- Use i915 instead of dev_priv insied the file_priv structure (Andi Shyti)
- Use proper parameter naming in for_each_engine() (Andi Shyti)
- Use gt_err for GT info (Tejas Upadhyay)
- Consolidate duplicated capture list code (John Harrison)
- Capture list naming clean up (John Harrison)
- Use kernel-doc -Werror when CONFIG_DRM_I915_WERROR=y (Jani Nikula)
- Preparation for using PAT index (Fei Yang)
- Use pat_index instead of cache_level (Fei Yang)
Miscellaneous:
- Fix memory leaks in i915 selftests (Cong Liu)
- Record GT error for gt failure (Tejas Upadhyay)
- Migrate platform-dependent mock hugepage selftests to live (Jonathan Cavitt)
- Update the SLPC selftest (Vinay Belgaumkar)
- Throw out set() wrapper (Jani Nikula)
- Large driver kernel doc cleanup (Jani Nikula)
- Fix probe injection CI failures after recent change (John Harrison)
- Make unexpected firmware versions an error in debug builds (John Harrison)
- Silence UBSAN uninitialized bool variable warning (Ashutosh Dixit)
- Fix memory leaks in function live_nop_switch (Cong Liu)
Merges:
- Merge drm/drm-next into drm-intel-gt-next (Joonas Lahtinen)
Geert Uytterhoeven [Tue, 23 May 2023 15:31:37 +0000 (17:31 +0200)]
drm: shmobile: Make DRM_SHMOBILE visible on Renesas SoC platforms
The LCD Controller supported by the drm-shmob driver is present
on SuperH SH-Mobile SoCs, and on Renesas ARM SH/R-Mobile SoCs.
Unfortunately its config option is not visible on either, so the user
can never enable the support.
Fix this by dropping the dependency on ARM (for SuperH), and by widening
the dependency range to ARCH_RENESAS (for ARM).
Geert Uytterhoeven [Tue, 23 May 2023 15:31:35 +0000 (17:31 +0200)]
drm: shmobile: Switch to drm_crtc_init_with_planes()
The SH-Mobile DRM driver uses the legacy drm_crtc_init(), which
advertizes only the formats in safe_modeset_formats[] (XR24 and AR24) as
being supported.
Switch to drm_crtc_init_with_planes(), and advertize all supported
(A)RGB modes, so we can use RGB565 as the default mode for the console.
Azeem Shaikh [Tue, 23 May 2023 02:19:43 +0000 (02:19 +0000)]
dma-buf/sw_sync: Replace all non-returning strlcpy with strscpy
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
Artur Weber [Wed, 24 May 2023 08:43:24 +0000 (10:43 +0200)]
drm/panel: samsung-s6d7aa0: use pointer for drm_mode in panel desc struct
Fixes compilation issues with older GCC versions and Clang after
changes introduced in commit 6810bb390282 ("drm/panel: Add Samsung
S6D7AA0 panel controller driver"). Tested with GCC 13.1.1, GCC 6.4.0
and Clang 16.0.3.
Fixes the following errors with Clang:
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_lsl080al02_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_lsl080al03_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_ltl101at01_mode,
^~~~~~~~~~~~~~~~~~~~~~~
3 errors generated.
Fixes the following errors with GCC:
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: error: initializer element is not constant
.drm_mode = s6d7aa0_lsl080al02_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: note: (near initialization for 's6d7aa0_lsl080al02_desc.drm_mode')
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: error: initializer element is not constant
.drm_mode = s6d7aa0_lsl080al03_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: note: (near initialization for 's6d7aa0_lsl080al03_desc.drm_mode')
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: error: initializer element is not constant
.drm_mode = s6d7aa0_ltl101at01_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: note: (near initialization for 's6d7aa0_ltl101at01_desc.drm_mode')
Azeem Shaikh [Mon, 22 May 2023 15:52:10 +0000 (15:52 +0000)]
drm/bridge: dw-hdmi: Replace all non-returning strlcpy with strscpy
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
Nícolas F. R. A. Prado [Thu, 18 May 2023 19:39:02 +0000 (15:39 -0400)]
drm/bridge: anx7625: Prevent endless probe loop
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel") Fixes: 269332997a16 ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found") Reported-by: "kernelci.org bot" <bot@kernelci.org> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Fei Yang [Fri, 19 May 2023 05:11:02 +0000 (22:11 -0700)]
drm/i915/mtl: end support for set caching ioctl
The design is to keep Buffer Object's caching policy immutable through
out its life cycle. This patch ends the support for set caching ioctl
from MTL onward. While doing that we also set BO's to be 1-way coherent
at creation time because GPU is no longer automatically snooping CPU
cache. For userspace components needing to fine tune the caching policy
for BO's, a follow up patch will extend the GEM_CREATE uAPI to allow
them specify caching mode at BO creation time.
Tvrtko Ursulin [Fri, 19 May 2023 15:49:44 +0000 (08:49 -0700)]
drm/i915/pmu: Add reference counting to the sampling timer
We do not want to have timers per tile and waste CPU cycles and energy via
multiple wake-up sources, for a relatively un-important task of PMU
sampling, so keeping a single timer works well. But we also do not want
the first GT which goes idle to turn off the timer.
Add some reference counting, via a mask of unparked GTs, to solve this.
v2: Drop the check for unparked in i915_sample (Ashutosh)
v3: Revert v2 (Tvrtko)
Marek Vasut [Sun, 14 May 2023 11:46:25 +0000 (08:46 -0300)]
drm: bridge: samsung-dsim: Implement support for clock/data polarity swap
Implement support for DSI clock and data lane DN/DP polarity swap by
means of decoding 'lane-polarities' DT property. The controller does
support DN/DP swap of clock lane and all data lanes, the controller
does not support polarity swap of individual data lane bundles, add
a check which verifies all data lanes have the same polarity.
This has been validated on an imx8mm board that actually has the MIPI DSI
clock lanes inverted.
The Samsung DSIM IP block allows the inversion of the clock and
data lanes.
Add an optional property called 'lane-polarities' that describes the
polarities of the MIPI DSI clock and data lanes.
This property is useful for properly describing the hardware when the
board designer decided to switch the polarities of the MIPI DSI
clock and/or data lanes.
Add bindings for the S6D7AA0 LCD panel controller, including the
S6D7AA0-LSL080AL02 panel used in the Samsung Galaxy Tab 3 8.0 family
of tablets, and the S6D7AA0-LSL080AL03 and S6D7AA0-LTL101AT01 panels
used in the Samsung Galaxy Tab A 8.0 and 9.7 2015.
Luben Tuikov [Wed, 17 May 2023 23:35:50 +0000 (19:35 -0400)]
drm/sched: Rename to drm_sched_wakeup_if_can_queue()
Rename drm_sched_wakeup() to drm_sched_wakeup_if_canqueue() since the former
is misleading, as it wakes up the GPU scheduler _only if_ more jobs can be
queued to the underlying hardware.
This distinction is important to make, since the wake conditional in the GPU
scheduler thread wakes up when other conditions are also true, e.g. when there
are jobs to be cleaned. For instance, a user might want to wake up the
scheduler only because there are more jobs to clean, but whether we can queue
more jobs is irrelevant.
Luben Tuikov [Wed, 17 May 2023 23:35:49 +0000 (19:35 -0400)]
drm/sched: Rename to drm_sched_can_queue()
Rename drm_sched_ready() to drm_sched_can_queue(). "ready" can mean many
things and is thus meaningless in this context. Instead, rename to a name
which precisely conveys what is being checked.
Radhakrishna Sripada [Wed, 17 May 2023 23:31:11 +0000 (16:31 -0700)]
drm/i915/mtl: Extend Wa_16014892111 to MTL A-step
Like DG2, MTL a-step hardware is subject to Wa_16014892111 which
requires that any changes made to the DRAW_WATERMARK register be
done via an INDIRECT_CTX batch buffer rather than through a regular
context workaround.
The bspec gives the same non-default recommended tuning value
for DRAW_WATERMARK as DG2, so we can re-use the INDIRECT_CTX code
to apply that tuning setting on A-step hardware.
Application of the tuning setting on B-step and later does not
need INDIRECT_CTX handling and is already done in
mtl_ctx_workarounds_init() as usual.
v2: Limit the WA for A-step
v3: Update the commit message.
v4: Reorder platform checks and update commit message.
Radhakrishna Sripada [Wed, 17 May 2023 23:31:10 +0000 (16:31 -0700)]
drm/i915/mtl: Add MTL performance tuning changes
MTL reuses the tuning parameters for DG2. Extend the dg2
performance tuning parameters to MTL.
v2: Add DRAW_WATERMARK tuning parameter.
v3: Limit DRAW_WATERMARK tuning to non A0 step.
v4: Reorder platform checks.
Restrict Blend fill caching optimization to Render GT.
v5: Move mtl tuning params to its own function
Andrzej Hajda [Thu, 18 May 2023 14:50:52 +0000 (16:50 +0200)]
drm/i915/mtl: do not enable render power-gating on MTL
Multiple CI tests fails with forcewake ack timeouts if render
power gating is enabled.
BSpec 52698 states it should be 0 for MTL, but apparently
this info is outdated. Anyway since the patch makes MTL pass basic
tests added FIXME tag informing this is temporary workaround.
Thomas Zimmermann [Fri, 12 May 2023 10:24:44 +0000 (12:24 +0200)]
fbdev: Rename fb_mem*() helpers
Update the names of the fb_mem*() helpers to be consistent with their
regular counterparts. Hence, fb_memset() now becomes fb_memset_io(),
fb_memcpy_fromfb() now becomes fb_memcpy_fromio() and fb_memcpy_tofb()
becomes fb_memcpy_toio(). No functional changes.
Thomas Zimmermann [Fri, 12 May 2023 10:24:43 +0000 (12:24 +0200)]
fbdev: Move framebuffer I/O helpers into <asm/fb.h>
Implement framebuffer I/O helpers, such as fb_read*() and fb_write*(),
in the architecture's <asm/fb.h> header file or the generic one.
The common case has been the use of regular I/O functions, such as
__raw_readb() or memset_io(). A few architectures used plain system-
memory reads and writes. Sparc used helpers for its SBus.
The architectures that used special cases provide the same code in
their __raw_*() I/O helpers. So the patch replaces this code with the
__raw_*() functions and moves it to <asm-generic/fb.h> for all
architectures.
v8:
* remove garbage after commit-message tags
v6:
* fix fb_readq()/fb_writeq() on 64-bit mips (kernel test robot)
v5:
* include <linux/io.h> in <asm-generic/fb>; fix s390 build
v4:
* ia64, loongarch, sparc64: add fb_mem*() to arch headers
to keep current semantics (Arnd)
v3:
* implement all architectures with generic helpers
* support reordering and native byte order (Geert, Arnd)
Thomas Zimmermann [Fri, 12 May 2023 10:24:42 +0000 (12:24 +0200)]
fbdev: Include <linux/fb.h> instead of <asm/fb.h>
Replace include statements for <asm/fb.h> with <linux/fb.h>. Fixes
the coding style: if a header is available in asm/ and linux/, it
is preferable to include the header from linux/. This only affects
a few source files, most of which already include <linux/fb.h>.
Thomas Zimmermann [Fri, 12 May 2023 10:24:38 +0000 (12:24 +0200)]
fbdev/hitfb: Cast I/O offset to address
Cast I/O offsets to pointers to use them with I/O functions. The I/O
functions expect pointers of type 'volatile void __iomem *', but the
offsets are plain integers. Build warnings are
../drivers/video/fbdev/hitfb.c: In function 'hitfb_accel_wait':
../arch/x86/include/asm/hd64461.h:18:33: warning: passing argument 1 of 'fb_readw' makes pointer from integer without a cast [-Wint-conversion]
18 | #define HD64461_IO_OFFSET(x) (HD64461_IOBASE + (x))
| ^~~~~~~~~~~~~~~~~~~~~~
| |
| unsigned int
../arch/x86/include/asm/hd64461.h:93:33: note: in expansion of macro 'HD64461_IO_OFFSET'
93 | #define HD64461_GRCFGR HD64461_IO_OFFSET(0x1044) /* Accelerator Configuration Register */
| ^~~~~~~~~~~~~~~~~
../drivers/video/fbdev/hitfb.c:47:25: note: in expansion of macro 'HD64461_GRCFGR'
47 | while (fb_readw(HD64461_GRCFGR) & HD64461_GRCFGR_ACCSTATUS) ;
| ^~~~~~~~~~~~~~
In file included from ../arch/x86/include/asm/fb.h:15,
from ../include/linux/fb.h:19,
from ../drivers/video/fbdev/hitfb.c:22:
../include/asm-generic/fb.h:52:57: note: expected 'const volatile void *' but argument is of type 'unsigned int'
52 | static inline u16 fb_readw(const volatile void __iomem *addr)
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
This patch only fixes the build warnings. It's not clear if the I/O
offsets can legally be passed to the I/O helpers. It was apparently
broken in 2007 when custom inw()/outw() helpers got removed by
commit 34a780a0afeb ("sh: hp6xx pata_platform support."). Fixing the
driver would require setting the I/O base address.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202305102136.eMjTSPwH-lkp@intel.com/ Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Cc: Artur Rojek <contact@artur-rojek.eu> Acked-by: Helge Deller <deller@gmx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-2-tzimmermann@suse.de
Vinay Belgaumkar [Tue, 16 May 2023 15:49:05 +0000 (08:49 -0700)]
drm/i915/guc/slpc: Disable rps_boost debugfs
rps_boost debugfs shows host turbo related info. This is not valid
when SLPC is enabled. guc_slpc_info already shows the number of boosts.
Add num_waiters there as well and disable rps_boost when SLPC is
enabled.
v2: Replace Bug with Link to resolve checkpatch warning
John Harrison [Tue, 18 Apr 2023 18:17:44 +0000 (11:17 -0700)]
drm/i915/guc: Dump error capture to dmesg on CTB error
In the past, There have been sporadic CTB failures which proved hard
to reproduce manually. The most effective solution was to dump the GuC
log at the point of failure and let the CI system do the repro. It is
preferable not to dump the GuC log via dmesg for all issues as it is
not always necessary and is not helpful for end users. But rather than
trying to re-invent the code to do this each time it is wanted, commit
the code but for DEBUG_GUC builds only.
John Harrison [Tue, 18 Apr 2023 18:17:43 +0000 (11:17 -0700)]
drm/i915: Dump error capture to kernel log
This is useful for getting debug information out in certain
situations, such as failing kernel selftests and CI runs that don't
log error captures. It is especially useful for things like retrieving
GuC logs as GuC operation can't be tracked by adding printk or ftrace
entries.
v2: Add CONFIG_DRM_I915_DEBUG_GEM wrapper (review feedback by Rodrigo).
There is a problem of screen shake on the old panel. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code mainly
modifles the following.
a)adjusted for GOP timing. When Display sleep in, raise all GOP signals
to VGHO and then drop to GND.
b)Increased the Vertical back Porch and Vertical pulse width, so need to
update vsync_end and vtotal and CLK in drm_display_mode.
Anup Sharma [Sat, 13 May 2023 10:12:17 +0000 (15:42 +0530)]
gpu: drm: bridge: No need to set device_driver owner
There is no need to exclusively set the .owner member of the struct
device_driver when defining the platform_driver struct. The Linux core
takes care of setting the .owner member as part of the call to
module_platform_driver() helper function.
Issue identified using the platform_no_drv_owner.cocci Coccinelle
semantic patch as:
drivers/gpu/drm/bridge/samsung-dsim.c:1957:6-11: No need to set .owner here.
The core will do it.
The TC358867/TC9595 devices are compatible with the predecessor TC358767.
Document compatible strings for the new devices, so they can be discerned
in board DTs. Update the title to match description in the process.
Maíra Canal [Fri, 12 May 2023 10:40:45 +0000 (07:40 -0300)]
drm/vkms: Fix RGB565 pixel conversion
Currently, the pixel conversion isn't rounding the fixed-point values
before assigning it to the RGB coefficients, which is causing the IGT
pixel-format tests to fail. So, use the drm_fixp2int_round() fixed-point
helper to round the values when assigning it to the RGB coefficients.
Tested with igt@kms_plane@pixel-format and igt@kms_plane@pixel-format-source-clamping.
[v2]:
* Use drm_fixp2int_round() to fix the pixel conversion instead of
casting the values to s32 (Melissa Wen).
Shuijing Li [Mon, 15 May 2023 09:49:55 +0000 (17:49 +0800)]
drm/panel: boe-tv101wum-nl6: Fine tune the panel power sequence
For "boe,tv105wum-nw0" this special panel, it is stipulated in
the panel spec that MIPI needs to keep the LP11 state before
the lcm_reset pin is pulled high.
Shuijing Li [Mon, 15 May 2023 09:49:54 +0000 (17:49 +0800)]
drm/panel: boe-tv101wum-nl6: Remove extra delay
Reduce the delay after LCM reset by removing an extra delay in the
initialization commands array. The required delay of at least 6ms after
reset is guaranteed by boe_panel_prepare().
drivers/firmware: Move sysfb_init() from device_initcall to subsys_initcall_sync
Consider a configuration like this:
1, efifb (or simpledrm) is built-in;
2, a native display driver (such as radeon) is also built-in.
As Javier said, this is not a common configuration (the native display
driver is usually built as a module), but it can happen and cause some
trouble.
In this case, since efifb, radeon and sysfb are all in device_initcall()
level, the order in practise is like this:
efifb registered at first, but no "efi-framebuffer" device yet. radeon
registered later, and /dev/fb0 created. sysfb_init() comes at last, it
registers "efi-framebuffer" and then causes an error message "efifb: a
framebuffer is already registered". Make sysfb_init() to be subsys_
initcall_sync() can avoid this. And Javier Martinez Canillas is trying
to make a more general solution in commit 873eb3b11860 ("fbdev: Disable
sysfb device registration when removing conflicting FBs").
However, this patch still makes sense because it can make the screen
display as early as possible (We cannot move to subsys_initcall, since
sysfb_init() should be executed after PCI enumeration).
Loading i915 on UBSAN enabled kernels (CONFIG_UBSAN/CONFIG_UBSAN_BOOL)
causes the following warning:
UBSAN: invalid-load in drivers/gpu/drm/i915/gt/uc/intel_uc.c:558:2
load of value 255 is not a valid value for type '_Bool'
Call Trace:
dump_stack_lvl+0x57/0x7d
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value.cold+0x43/0x48
__uc_init_hw+0x76a/0x903 [i915]
...
i915_driver_probe+0xfb1/0x1eb0 [i915]
i915_pci_probe+0xbe/0x2d0 [i915]
The warning happens because during probe i915_hwmon is still not available
which results in the output boolean variable *old remaining
uninitialized. Silence the warning by initializing the variable to an
arbitrary value.
v2: Move variable initialization to the declaration (Andi)
Linus Torvalds [Sun, 14 May 2023 19:32:34 +0000 (12:32 -0700)]
Merge tag 'cxl-fixes-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull compute express link fixes from Dan Williams:
- Fix a compilation issue with DEFINE_STATIC_SRCU() in the unit tests
- Fix leaking kernel memory to a root-only sysfs attribute
* tag 'cxl-fixes-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl: Add missing return to cdat read error path
tools/testing/cxl: Use DEFINE_STATIC_SRCU()
Linus Torvalds [Sun, 14 May 2023 16:54:38 +0000 (09:54 -0700)]
Merge tag 'parisc-for-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
- Include reboot.h to avoid gcc-12 compiler warning
* tag 'parisc-for-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
parisc: kexec: include reboot.h
Linus Torvalds [Sun, 14 May 2023 15:00:46 +0000 (08:00 -0700)]
Merge tag 'locking_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Borislav Petkov:
- Make sure __down_read_common() is always inlined so that the callers'
names land in traceevents output and thus the blocked function can be
identified
* tag 'locking_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Add __always_inline annotation to __down_read_common() and inlined callers
Linus Torvalds [Sun, 14 May 2023 14:56:51 +0000 (07:56 -0700)]
Merge tag 'perf_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Make sure the PEBS buffer is flushed before reprogramming the
hardware so that the correct record sizes are used
- Update the sample size for AMD BRS events
- Fix a confusion with using the same on-stack struct with different
events in the event processing path
* tag 'perf_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG
perf/x86: Fix missing sample size update on AMD BRS
perf/core: Fix perf_sample_data not properly initialized for different swevents in perf_tp_event()
Linus Torvalds [Sun, 14 May 2023 14:44:48 +0000 (07:44 -0700)]
Merge tag 'x86_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
- Add the required PCI IDs so that the generic SMN accesses provided by
amd_nb.c work for drivers which switch to them. Add a PCI device ID
to k10temp's table so that latter is loaded on such systems too
* tag 'x86_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hwmon: (k10temp) Add PCI ID for family 19, model 78h
x86/amd_nb: Add PCI ID for family 19h model 78h
Linus Torvalds [Sun, 14 May 2023 14:39:15 +0000 (07:39 -0700)]
Merge tag 'timers_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Prevent CPU state corruption when an active clockevent broadcast
device is replaced while the system is already in oneshot mode
* tag 'timers_urgent_for_v6.4_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Make broadcast device replacement work correctly
Linus Torvalds [Sun, 14 May 2023 00:45:39 +0000 (17:45 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some ext4 bug fixes (mostly to address Syzbot reports)"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: bail out of ext4_xattr_ibody_get() fails for any reason
ext4: add bounds checking in get_max_inline_xattr_value_size()
ext4: add indication of ro vs r/w mounts in the mount message
ext4: fix deadlock when converting an inline directory in nojournal mode
ext4: improve error recovery code paths in __ext4_remount()
ext4: improve error handling from ext4_dirhash()
ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled
ext4: check iomap type only if ext4_iomap_begin() does not fail
ext4: avoid a potential slab-out-of-bounds in ext4_group_desc_csum
ext4: fix data races when using cached status extents
ext4: avoid deadlock in fs reclaim with page writeback
ext4: fix invalid free tracking in ext4_xattr_move_to_block()
ext4: remove a BUG_ON in ext4_mb_release_group_pa()
ext4: allow ext4_get_group_info() to fail
ext4: fix lockdep warning when enabling MMP
ext4: fix WARNING in mb_find_extent
Linus Torvalds [Sun, 14 May 2023 00:37:32 +0000 (17:37 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single small fix for the UFS driver to fix a power management
failure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix I/O hang that occurs when BKOPS fails in W-LUN suspend
Helge Deller [Sat, 13 May 2023 20:30:06 +0000 (22:30 +0200)]
parisc: Fix encoding of swp_entry due to added SWP_EXCLUSIVE flag
Fix the __swp_offset() and __swp_entry() macros due to commit 6d239fc78c0b
("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE") which introduced the
SWP_EXCLUSIVE flag by reusing the _PAGE_ACCESSED flag.
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Tested-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Helge Deller <deller@gmx.de> Fixes: 6d239fc78c0b ("parisc/mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE") Cc: <stable@vger.kernel.org> # v6.3+
Theodore Ts'o [Fri, 12 May 2023 19:16:27 +0000 (15:16 -0400)]
ext4: bail out of ext4_xattr_ibody_get() fails for any reason
In ext4_update_inline_data(), if ext4_xattr_ibody_get() fails for any
reason, it's best if we just fail as opposed to stumbling on,
especially if the failure is EFSCORRUPTED.
Theodore Ts'o [Fri, 12 May 2023 19:11:02 +0000 (15:11 -0400)]
ext4: add bounds checking in get_max_inline_xattr_value_size()
Normally the extended attributes in the inode body would have been
checked when the inode is first opened, but if someone is writing to
the block device while the file system is mounted, it's possible for
the inode table to get corrupted. Add bounds checking to avoid
reading beyond the end of allocated memory if this happens.
Theodore Ts'o [Fri, 12 May 2023 18:49:57 +0000 (14:49 -0400)]
ext4: add indication of ro vs r/w mounts in the mount message
Whether the file system is mounted read-only or read/write is more
important than the quota mode, which we are already printing. Add the
ro vs r/w indication since this can be helpful in debugging problems
from the console log.
Theodore Ts'o [Sun, 7 May 2023 01:04:01 +0000 (21:04 -0400)]
ext4: fix deadlock when converting an inline directory in nojournal mode
In no journal mode, ext4_finish_convert_inline_dir() can self-deadlock
by calling ext4_handle_dirty_dirblock() when it already has taken the
directory lock. There is a similar self-deadlock in
ext4_incvert_inline_data_nolock() for data files which we'll fix at
the same time.
Theodore Ts'o [Sat, 6 May 2023 02:20:29 +0000 (22:20 -0400)]
ext4: improve error recovery code paths in __ext4_remount()
If there are failures while changing the mount options in
__ext4_remount(), we need to restore the old mount options.
This commit fixes two problem. The first is there is a chance that we
will free the old quota file names before a potential failure leading
to a use-after-free. The second problem addressed in this commit is
if there is a failed read/write to read-only transition, if the quota
has already been suspended, we need to renable quota handling.
Theodore Ts'o [Sat, 6 May 2023 15:59:13 +0000 (11:59 -0400)]
ext4: improve error handling from ext4_dirhash()
The ext4_dirhash() will *almost* never fail, especially when the hash
tree feature was first introduced. However, with the addition of
support of encrypted, casefolded file names, that function can most
certainly fail today.
So make sure the callers of ext4_dirhash() properly check for
failures, and reflect the errors back up to their callers.
Theodore Ts'o [Sat, 6 May 2023 01:02:30 +0000 (21:02 -0400)]
ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled
When a file system currently mounted read/only is remounted
read/write, if we clear the SB_RDONLY flag too early, before the quota
is initialized, and there is another process/thread constantly
attempting to create a directory, it's possible to trigger the
WARN_ON_ONCE(dquot_initialize_needed(inode));
in ext4_xattr_block_set(), with the following stack trace:
Baokun Li [Fri, 5 May 2023 13:24:29 +0000 (21:24 +0800)]
ext4: check iomap type only if ext4_iomap_begin() does not fail
When ext4_iomap_overwrite_begin() calls ext4_iomap_begin() map blocks may
fail for some reason (e.g. memory allocation failure, bare disk write), and
later because "iomap->type ! = IOMAP_MAPPED" triggers WARN_ON(). When ext4
iomap_begin() returns an error, it is normal that the type of iomap->type
may not match the expectation. Therefore, we only determine if iomap->type
is as expected when ext4_iomap_begin() is executed successfully.
Replace
le16_to_cpu(sbi->s_es->s_desc_size)
with
sbi->s_desc_size
It reduces ext4's compiled text size, and makes the code more efficient
(we remove an extra indirect reference and a potential byte
swap on big endian systems), and there is no downside. It also avoids the
potential KASAN / syzkaller failure, as a bonus.
Jan Kara [Thu, 4 May 2023 12:55:24 +0000 (14:55 +0200)]
ext4: fix data races when using cached status extents
When using cached extent stored in extent status tree in tree->cache_es
another process holding ei->i_es_lock for reading can be racing with us
setting new value of tree->cache_es. If the compiler would decide to
refetch tree->cache_es at an unfortunate moment, it could result in a
bogus in_range() check. Fix the possible race by using READ_ONCE() when
using tree->cache_es only under ei->i_es_lock for reading.
Jan Kara [Thu, 4 May 2023 12:47:23 +0000 (14:47 +0200)]
ext4: avoid deadlock in fs reclaim with page writeback
Ext4 has a filesystem wide lock protecting ext4_writepages() calls to
avoid races with switching of journalled data flag or inode format. This
lock can however cause a deadlock like:
CPU0 CPU1
ext4_writepages()
percpu_down_read(sbi->s_writepages_rwsem);
ext4_change_inode_journal_flag()
percpu_down_write(sbi->s_writepages_rwsem);
- blocks, all readers block from now on
ext4_do_writepages()
ext4_init_io_end()
kmem_cache_zalloc(io_end_cachep, GFP_KERNEL)
fs_reclaim frees dentry...
dentry_unlink_inode()
iput() - last ref =>
iput_final() - inode dirty =>
write_inode_now()...
ext4_writepages() tries to acquire sbi->s_writepages_rwsem
and blocks forever
Make sure we cannot recurse into filesystem reclaim from writeback code
to avoid the deadlock.
ext4: fix invalid free tracking in ext4_xattr_move_to_block()
In ext4_xattr_move_to_block(), the value of the extended attribute
which we need to move to an external block may be allocated by
kvmalloc() if the value is stored in an external inode. So at the end
of the function the code tried to check if this was the case by
testing entry->e_value_inum.
However, at this point, the pointer to the xattr entry is no longer
valid, because it was removed from the original location where it had
been stored. So we could end up calling kvfree() on a pointer which
was not allocated by kvmalloc(); or we could also potentially leak
memory by not freeing the buffer when it should be freed. Fix this by
storing whether it should be freed in a separate variable.
ext4: remove a BUG_ON in ext4_mb_release_group_pa()
If a malicious fuzzer overwrites the ext4 superblock while it is
mounted such that the s_first_data_block is set to a very large
number, the calculation of the block group can underflow, and trigger
a BUG_ON check. Change this to be an ext4_warning so that we don't
crash the kernel.
Previously, ext4_get_group_info() would treat an invalid group number
as BUG(), since in theory it should never happen. However, if a
malicious attaker (or fuzzer) modifies the superblock via the block
device while it is the file system is mounted, it is possible for
s_first_data_block to get set to a very large number. In that case,
when calculating the block group of some block number (such as the
starting block of a preallocation region), could result in an
underflow and very large block group number. Then the BUG_ON check in
ext4_get_group_info() would fire, resutling in a denial of service
attack that can be triggered by root or someone with write access to
the block device.
For a quality of implementation perspective, it's best that even if
the system administrator does something that they shouldn't, that it
will not trigger a BUG. So instead of BUG'ing, ext4_get_group_info()
will call ext4_error and return NULL. We also add fallback code in
all of the callers of ext4_get_group_info() that it might NULL.
Also, since ext4_get_group_info() was already borderline to be an
inline function, un-inline it. The results in a next reduction of the
compiled text size of ext4 by roughly 2k.
Linus Torvalds [Sat, 13 May 2023 14:51:03 +0000 (09:51 -0500)]
Merge tag 'block-6.4-2023-05-13' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Just a few minor fixes for drivers, and a deletion of a file that is
woefully out-of-date these days"
* tag 'block-6.4-2023-05-13' of git://git.kernel.dk/linux:
Documentation/block: drop the request.rst file
ublk: fix command op code check
block/rnbd: replace REQ_OP_FLUSH with REQ_OP_WRITE
nbd: Fix debugfs_create_dir error checking
Linus Torvalds [Fri, 12 May 2023 22:10:32 +0000 (17:10 -0500)]
Merge tag 'for-6.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs fixes from David Sterba:
- fix incorrect number of bitmap entries for space cache if loading is
interrupted by some error
- fix backref walking, this breaks a mode of LOGICAL_INO_V2 ioctl that
is used in deduplication tools
- zoned mode fixes:
- properly finish zone reserved for relocation
- correctly calculate super block zone end on ZNS
- properly initialize new extent buffer for redirty
- make mount option clear_cache work with block-group-tree, to rebuild
free-space-tree instead of temporarily disabling it that would lead
to a forced read-only mount
- fix alignment check for offset when printing extent item
* tag 'for-6.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: make clear_cache mount option to rebuild FST without disabling it
btrfs: zero the buffer before marking it dirty in btrfs_redirty_list_add
btrfs: zoned: fix full zone super block reading on ZNS
btrfs: zoned: zone finish data relocation BG with last IO
btrfs: fix backref walking not returning all inode refs
btrfs: fix space cache inconsistency after error loading it from disk
btrfs: print-tree: parent bytenr must be aligned to sector size
Linus Torvalds [Fri, 12 May 2023 22:01:36 +0000 (17:01 -0500)]
Merge tag '6.4-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
- fix for copy_file_range bug for very large files that are multiples
of rsize
- do not ignore "isolated transport" flag if set on share
- set rasize default better
- three fixes related to shutdown and freezing (fixes 4 xfstests, and
closes deferred handles faster in some places that were missed)
* tag '6.4-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: release leases for deferred close handles when freezing
smb3: fix problem remounting a share after shutdown
SMB3: force unmount was failing to close deferred close files
smb3: improve parallel reads of large files
do not reuse connection if share marked as isolated
cifs: fix pcchunk length type in smb2_copychunk_range
Linus Torvalds [Fri, 12 May 2023 21:56:09 +0000 (16:56 -0500)]
Merge tag 'vfs/v6.4-rc1/pipe' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fix from Christian Brauner:
"During the pipe nonblock rework the check for both O_NONBLOCK and
IOCB_NOWAIT was dropped. Both checks need to be performed to ensure
that files without O_NONBLOCK but IOCB_NOWAIT don't block when writing
to or reading from a pipe.
This just contains the fix adding the check for IOCB_NOWAIT back in"
* tag 'vfs/v6.4-rc1/pipe' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
pipe: check for IOCB_NOWAIT alongside O_NONBLOCK
Linus Torvalds [Fri, 12 May 2023 21:39:05 +0000 (16:39 -0500)]
Merge tag 'io_uring-6.4-2023-05-12' of git://git.kernel.dk/linux
Pull io_uring fix from Jens Axboe:
"Just a single fix making io_uring_sqe_cmd() available regardless of
CONFIG_IO_URING, fixing a regression introduced during the merge
window if nvme was selected but io_uring was not"
* tag 'io_uring-6.4-2023-05-12' of git://git.kernel.dk/linux:
io_uring: make io_uring_sqe_cmd() unconditionally available
Linus Torvalds [Fri, 12 May 2023 21:31:55 +0000 (16:31 -0500)]
Merge tag 'riscv-for-linus-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Palmer Dabbelt:
"Just a single fix this week for a build issue. That'd usually be a
good sign, but we've started to get some reports of boot failures on
some hardware/bootloader configurations. Nothing concrete yet, but
I've got a funny feeling that's where much of the bug hunting is going
right now.
Nothing's reproducing on my end, though, and this fixes some pretty
concrete issues so I figured there's no reason to delay it:
- a fix to the linker script to avoid orpahaned sections in
kernel/pi"
* tag 'riscv-for-linus-6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix orphan section warnings caused by kernel/pi
John Harrison [Fri, 12 May 2023 01:35:44 +0000 (18:35 -0700)]
drm/i915/guc: Fix confused register capture list creation
The GuC has a completely separate engine class enum when referring to
register capture lists, which combines render and compute. The driver
was using the 'normal' GuC specific engine class enum instead. That
meant that it thought it was defining a capture list for compute
engines, the list was actually being applied to the GSC engine. And if
a platform didn't have a render engine, then it would get no compute
register captures at all.
John Harrison [Wed, 10 May 2023 20:55:56 +0000 (13:55 -0700)]
drm/i1915/guc: Fix probe injection CI failures after recent change
A recent change bumped a 'notice' message up to 'error' level for
debug builds to help trap incorrect configurations in CI systems.
Unfortunately, the error condition in question is triggered by the
error injection probe test. So change the message again to be 'probe
error' level instead.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Fixes: 760133d42f0a ("drm/i915/uc: Make unexpected firmware versions an error in debug builds") Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Alan Previn <alan.previn.teres.alexis@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230510205556.312999-1-John.C.Harrison@Intel.com
projects / users / jedix / linux-maple.git / log