arm64: dts: imx93: assign usdhc[1..3] root clock to 400MHz
1. Config SDHC1 clock 400MHz to support eMMC HS400ES mode
2. The original usdhc2 and usdhc3 root clock is 200MHz. Then WIFI
on usdhc3 at SDR104 mode can work under 200MHz. But if imx93 work
under Low Drive mode, the usdhc3 pad signal is not good under 200MHz,
SDR104 mode can't work stable. Need to downgrade to 133MHz to let
WIFI work stable. To cover all the cases, for Norminal Drive mode,
keep usdhc root at 400MHz, then card(SD/wifi) can work at SDR104 mode
under 200MHz to get the best performance. For Low Drive mode,
bootloader need override usdhc root clock to 266MHz, and the
card(SD/wifi) work at SDR104 mode under 133MHz, can work stable.
Reviewed-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCI devices should use PCI interrupt binding for their interrupts assuming
they function as standard PCI interrupts. The embedded PCI devices in the
LS1028a are mapping the interrupts directly to the host interrupt
controller. While that works here, it is unusual.
Based on the reference manual, there is not any INTC or INTD to map, so
only INTA and INTB are mapped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marek Vasut [Wed, 17 Apr 2024 11:42:06 +0000 (13:42 +0200)]
arm64: dts: imx8mp: Align both CSI2 pixel clock
Configure both CSI2 clock-frequency and assigned-clock-rates
the same way. There does not seem to be any reason for keeping
the two CSI2 pixel clock set to different frequencies.
This also reduces first CSI2 clock from overdrive mode
frequency which is 500 MHz down below the regular mode
frequency of 400 MHz.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: freescale: imx8m[mp]-verdin: Update audio card name
On the Dahlia and Development carrier boards for the Verdin family
(iMX8MM and iMX8MP), WM8904 and NAU8822 codecs are used. Instead of
module-specific names, switch to more generic names based on the codec
employed on the carrier board itself.
This modification facilitates access to ALSA card names, ensuring
consistency across iMX8MP and iMX8MM, as they share the same carrier
board.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Eichenberger [Fri, 5 Apr 2024 16:07:20 +0000 (18:07 +0200)]
arm64: dts: freescale: imx8mm-verdin-dahlia: support sleep-moci
Previously, we had the sleep-moci pin set to always on. However, the
Dahlia carrier board supports disabling the sleep-moci when the system
is suspended to power down peripherals that support it. This reduces
overall power consumption. This commit adds support for this feature by
disabling the reg_force_sleep_moci regulator and adding two new
regulators for the USB hub and PCIe that can be turned off when the
system is suspended.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Eichenberger [Fri, 5 Apr 2024 16:07:19 +0000 (18:07 +0200)]
arm64: dts: freescale: imx8mm-verdin: replace sleep-moci hog with regulator
The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Eichenberger [Fri, 5 Apr 2024 16:07:18 +0000 (18:07 +0200)]
arm64: dts: freescale: imx8mp-verdin-dahlia: support sleep-moci
Previously, we had the sleep-moci pin set to always on. However, the
Dahlia carrier board supports disabling the sleep-moci when the system
is suspended to power down peripherals that support it. This reduces
overall power consumption. This commit adds support for this feature by
disabling the reg_force_sleep_moci regulator and adding two new
regulators for the USB hub and PCIe that can be turned off when the
system is suspended.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Eichenberger [Fri, 5 Apr 2024 16:07:17 +0000 (18:07 +0200)]
arm64: dts: freescale: imx8mp-verdin: replace sleep-moci hog with regulator
The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: imx8mp-debix-som-a-bmb-08: Remove 'phy-supply' from eqos
Per nxp,dwmac-imx.yaml, it is not valid to pass 'phy-supply'.
Remove it to fix the following dt-schema warning:
ethernet@30bf0000: Unevaluated properties are not allowed ('phy-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml#
The I2C2 bus is used for the CSI and DSI connectors only, no devices are
connected to it on neither the Debix Model A nor its IO board. Disable
the bus in the board's .dts and remove its clock frequency settings, as
the value depends solely on the devices conncted to the CSI and DSI
connectors. Display panel or camera sensor overlays will configure and
enable the bus when necessary.
Add support for Toradex Colibri iMX8DX SoM and Aster, Evaluation Board v3,
Iris and Iris v2 carrier boards the module can be mated in.
This SoM is a variant of the already supported Colibri iMX8QXP, using an
NXP i.MX8DX SoC instead of i.MX8QXP.
Add DTSI for i.MX8DX processor. According to 'i.MX 8DualX Industrial
Applications Processors Data Sheet', the GPU and shader use a clock of
372MHz. Therefore, this dtsi includes the imx8dxp.dtsi and changes the
clock accordingly.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devicetree files can be (re-)used in u-boot now, they are imported
on a regular basis (see OF_UPSTREAM option) there. Up until now, it
didn't matter for linux and there was just a combined devicetree
"-var3-ads2" (with ads2 being the carrier board). But if the devicetree
files are now reused in u-boot, we need to have an individual "-var3"
variant, because the bootloader is just using the bare "varN" devicetree
files. Split the "var3" off of the "-var3-ads2" devicetree.
Signed-off-by: Michael Walle <mwalle@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alice Guo [Tue, 2 Apr 2024 14:41:29 +0000 (10:41 -0400)]
arm64: dts: imx8dxl: add lpuart device in cm40 subsystem
Add lpuart device in cm40 subsystem.
Signed-off-by: Alice Guo <alice.guo@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Wadim Mueller [Sun, 24 Mar 2024 21:43:26 +0000 (22:43 +0100)]
arm64: dts: S32G3: Introduce device tree for S32G-VNP-RDB3
This commit adds device tree support for the NXP S32G3-based
S32G-VNP-RDB3 Board [1].
The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.
The device tree files are derived from the official NXP downstream
Linux tree [2].
This addition encompasses a limited selection of peripherals that
are upstream-supported. Apart from the ARM System Modules
(GIC, Generic Timer, etc.), the following IPs have been validated:
* UART: fsl-linflexuart
* SDHC: fsl-imx-esdhc
Clock settings for the chip rely on ATF Firmware [3].
Pin control integration into the device tree is pending and currently
relies on Firmware/U-Boot settings [4].
These changes were validated using BSP39 Firmware/U-Boot from NXP [5].
The modifications enable booting the official Ubuntu 22.04 from NXP on
the RDB3 with default settings from the SD card and eMMC.
The production PDK3 carrier board rev.200 contains additional GPIO
expander to control power and reset signals for each CSI2 plug
separately. Describe this expander in the carrier board DT. The
label is used by sensor DTOs to reference the expander and its
signals.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warning from a 'make dtbs W=1':
arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx-imx219.dtso:65.10-70.5:
Warning (unit_address_vs_reg): /fragment@3/__overlay__/ports/port@0:
node has a unit name, but no reg or ranges property
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shengjiu Wang [Wed, 28 Feb 2024 03:30:11 +0000 (11:30 +0800)]
arm64: dts: imx8mp: Add AUD2HTX device node
The AUD2HTX is a digital module that provides a bridge between
the Audio Subsystem and the HDMI RTX Subsystem. This
module includes intermediate storage to queue SDMA transactions
prior to being synchronized and passed to the HDMI
RTX Subsystem over the Audio Link.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 24 Mar 2024 20:54:06 +0000 (13:54 -0700)]
Merge tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix panic in kdump kernel
x86/efistub: Don't clear BSS twice in mixed mode
x86/efistub: Call mixed mode boot services on the firmware's stack
efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
Linus Torvalds [Sun, 24 Mar 2024 18:13:56 +0000 (11:13 -0700)]
Merge tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Ensure that the encryption mask at boot is properly propagated on
5-level page tables, otherwise the PGD entry is incorrectly set to
non-encrypted, which causes system crashes during boot.
- Undo the deferred 5-level page table setup as it cannot work with
memory encryption enabled.
- Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
to the default value but the cached variable is not, so subsequent
comparisons might yield the wrong result and as a consequence the
result prevents updating the MSR.
- Register the local APIC address only once in the MPPARSE enumeration
to prevent triggering the related WARN_ONs() in the APIC and topology
code.
- Handle the case where no APIC is found gracefully by registering a
fake APIC in the topology code. That makes all related topology
functions work correctly and does not affect the actual APIC driver
code at all.
- Don't evaluate logical IDs during early boot as the local APIC IDs
are not yet enumerated and the invoked function returns an error
code. Nothing requires the logical IDs before the final CPUID
enumeration takes place, which happens after the enumeration.
- Cure the fallout of the per CPU rework on UP which misplaced the
copying of boot_cpu_data to per CPU data so that the final update to
boot_cpu_data got lost which caused inconsistent state and boot
crashes.
- Use copy_from_kernel_nofault() in the kprobes setup as there is no
guarantee that the address can be safely accessed.
- Reorder struct members in struct saved_context to work around another
kmemleak false positive
- Remove the buggy code which tries to update the E820 kexec table for
setup_data as that is never passed to the kexec kernel.
- Update the resource control documentation to use the proper units.
- Fix a Kconfig warning observed with tinyconfig
* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/64: Move 5-level paging global variable assignments back
x86/boot/64: Apply encryption mask to 5-level pagetable update
x86/cpu: Add model number for another Intel Arrow Lake mobile processor
x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
Documentation/x86: Document that resctrl bandwidth control units are MiB
x86/mpparse: Register APIC address only once
x86/topology: Handle the !APIC case gracefully
x86/topology: Don't evaluate logical IDs during early boot
x86/cpu: Ensure that CPU info updates are propagated on UP
kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
x86/pm: Work around false positive kmemleak report in msr_build_context()
x86/kexec: Do not update E820 kexec table for setup_data
x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'
Linus Torvalds [Sun, 24 Mar 2024 18:11:05 +0000 (11:11 -0700)]
Merge tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler doc clarification from Thomas Gleixner:
"A single update for the documentation of the base_slice_ns tunable to
clarify that any value which is less than the tick slice has no effect
because the scheduler tick is not guaranteed to happen within the set
time slice"
* tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Update documentation for base_slice_ns and CONFIG_HZ relation
Linus Torvalds [Sun, 24 Mar 2024 17:45:31 +0000 (10:45 -0700)]
Merge tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"This has a set of swiotlb alignment fixes for sometimes very long
standing bugs from Will. We've been discussion them for a while and
they should be solid now"
* tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: Reinstate page-alignment for mappings >= PAGE_SIZE
iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
swiotlb: Fix alignment checks when both allocation and DMA masks are present
swiotlb: Honour dma_alloc_coherent() alignment in swiotlb_alloc()
swiotlb: Enforce page alignment in swiotlb_alloc()
swiotlb: Fix double-allocation of slots due to broken alignment handling
Oleksandr Tymoshenko [Sat, 23 Mar 2024 06:33:33 +0000 (06:33 +0000)]
efi: fix panic in kdump kernel
Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.
Tested with QEMU and OVMF firmware.
Fixes: bad267f9e18f ("efi: verify that variable services are supported") Signed-off-by: Oleksandr Tymoshenko <ovt@google.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Ard Biesheuvel [Fri, 22 Mar 2024 16:01:45 +0000 (17:01 +0100)]
x86/efistub: Don't clear BSS twice in mixed mode
Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.
So make the memset() conditional on whether the EFI stub is running in
native mode.
Ard Biesheuvel [Fri, 22 Mar 2024 15:03:58 +0000 (17:03 +0200)]
x86/efistub: Call mixed mode boot services on the firmware's stack
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb0011983b ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.
Tom Lendacky [Fri, 22 Mar 2024 15:41:07 +0000 (10:41 -0500)]
x86/boot/64: Move 5-level paging global variable assignments back
Commit 63bed9660420 ("x86/startup_64: Defer assignment of 5-level paging
global variables") moved assignment of 5-level global variables to later
in the boot in order to avoid having to use RIP relative addressing in
order to set them. However, when running with 5-level paging and SME
active (mem_encrypt=on), the variables are needed as part of the page
table setup needed to encrypt the kernel (using pgd_none(), p4d_offset(),
etc.). Since the variables haven't been set, the page table manipulation
is done as if 4-level paging is active, causing the system to crash on
boot.
While only a subset of the assignments that were moved need to be set
early, move all of the assignments back into check_la57_support() so that
these assignments aren't spread between two locations. Instead of just
reverting the fix, this uses the new RIP_REL_REF() macro when assigning
the variables.
Tom Lendacky [Fri, 22 Mar 2024 15:41:06 +0000 (10:41 -0500)]
x86/boot/64: Apply encryption mask to 5-level pagetable update
When running with 5-level page tables, the kernel mapping PGD entry is
updated to point to the P4D table. The assignment uses _PAGE_TABLE_NOENC,
which, when SME is active (mem_encrypt=on), results in a page table
entry without the encryption mask set, causing the system to crash on
boot.
Change the assignment to use _PAGE_TABLE instead of _PAGE_TABLE_NOENC so
that the encryption mask is set for the PGD entry.
Adamos Ttofari [Fri, 22 Mar 2024 23:04:39 +0000 (16:04 -0700)]
x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
Commit 672365477ae8 ("x86/fpu: Update XFD state where required") and
commit 8bf26758ca96 ("x86/fpu: Add XFD state to fpstate") introduced a
per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in
order to avoid unnecessary writes to the MSR.
On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which
wipes out any stale state. But the per CPU cached xfd value is not
reset, which brings them out of sync.
As a consequence a subsequent xfd_update_state() might fail to update
the MSR which in turn can result in XRSTOR raising a #NM in kernel
space, which crashes the kernel.
To fix this, introduce xfd_set_state() to write xfd_state together
with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD.
Fixes: 672365477ae8 ("x86/fpu: Update XFD state where required") Signed-off-by: Adamos Ttofari <attofari@amazon.de> Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de
Tony Luck [Fri, 22 Mar 2024 18:20:15 +0000 (11:20 -0700)]
Documentation/x86: Document that resctrl bandwidth control units are MiB
The memory bandwidth software controller uses 2^20 units rather than
10^6. See mbm_bw_count() which computes bandwidth using the "SZ_1M"
Linux define for 0x00100000.
Update the documentation to use MiB when describing this feature.
It's too late to fix the mount option "mba_MBps" as that is now an
established user interface.
Linus Torvalds [Sat, 23 Mar 2024 21:49:25 +0000 (14:49 -0700)]
Merge tag 'timers-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two regression fixes for the timer and timer migration code:
- Prevent endless timer requeuing which is caused by two CPUs racing
out of idle. This happens when the last CPU goes idle and therefore
has to ensure to expire the pending global timers and some other
CPU come out of idle at the same time and the other CPU wins the
race and expires the global queue. This causes the last CPU to
chase ghost timers forever and reprogramming it's clockevent device
endlessly.
Cure this by re-evaluating the wakeup time unconditionally.
- The split into local (pinned) and global timers in the timer wheel
caused a regression for NOHZ full as it broke the idle tracking of
global timers. On NOHZ full this prevents an self IPI being sent
which in turn causes the timer to be not programmed and not being
expired on time.
Restore the idle tracking for the global timer base so that the
self IPI condition for NOHZ full is working correctly again"
* tag 'timers-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix removed self-IPI on global timer's enqueue in nohz_full
timers/migration: Fix endless timer requeue after idle interrupts
Linus Torvalds [Sat, 23 Mar 2024 21:42:45 +0000 (14:42 -0700)]
Merge tag 'timers-core-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more clocksource updates from Thomas Gleixner:
"A set of updates for clocksource and clockevent drivers:
- A fix for the prescaler of the ARM global timer where the prescaler
mask define only covered 4 bits while it is actully 8 bits wide.
This obviously restricted the possible range of prescaler
adjustments
- A fix for the RISC-V timer which prevents a timer interrupt being
raised while the timer is initialized
- A set of device tree updates to support new system on chips in
various drivers
- Kernel-doc and other cleanups all over the place"
* tag 'timers-core-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-riscv: Clear timer interrupt on timer initialization
dt-bindings: timer: Add support for cadence TTC PWM
clocksource/drivers/arm_global_timer: Simplify prescaler register access
clocksource/drivers/arm_global_timer: Guard against division by zero
clocksource/drivers/arm_global_timer: Make gt_target_rate unsigned long
dt-bindings: timer: add Ralink SoCs system tick counter
clocksource: arm_global_timer: fix non-kernel-doc comment
clocksource/drivers/arm_global_timer: Remove stray tab
clocksource/drivers/arm_global_timer: Fix maximum prescaler value
clocksource/drivers/imx-sysctr: Add i.MX95 support
clocksource/drivers/imx-sysctr: Drop use global variables
dt-bindings: timer: nxp,sysctr-timer: support i.MX95
dt-bindings: timer: renesas: ostm: Document RZ/Five SoC
dt-bindings: timer: renesas,tmu: Document input capture interrupt
clocksource/drivers/ti-32K: Fix misuse of "/**" comment
clocksource/drivers/stm32: Fix all kernel-doc warnings
dt-bindings: timer: exynos4210-mct: Add google,gs101-mct compatible
clocksource/drivers/imx: Fix -Wunused-but-set-variable warning
Linus Torvalds [Sat, 23 Mar 2024 21:30:38 +0000 (14:30 -0700)]
Merge tag 'irq-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A series of fixes for the Renesas RZG21 interrupt chip driver to
prevent spurious and misrouted interrupts.
- Ensure that posted writes are flushed in the eoi() callback
- Ensure that interrupts are masked at the chip level when the
trigger type is changed
- Clear the interrupt status register when setting up edge type
trigger modes
- Ensure that the trigger type and routing information is set before
the interrupt is enabled"
* tag 'irq-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time
irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type
irqchip/renesas-rzg2l: Rename rzg2l_irq_eoi()
irqchip/renesas-rzg2l: Rename rzg2l_tint_eoi()
irqchip/renesas-rzg2l: Flush posted write in irq_eoi()
Linus Torvalds [Sat, 23 Mar 2024 21:17:37 +0000 (14:17 -0700)]
Merge tag 'core-entry-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core entry fix from Thomas Gleixner:
"A single fix for the generic entry code:
The trace_sys_enter() tracepoint can modify the syscall number via
kprobes or BPF in pt_regs, but that requires that the syscall number
is re-evaluted from pt_regs after the tracepoint.
A seccomp fix in that area removed the re-evaluation so the change
does not take effect as the code just uses the locally cached number.
Restore the original behaviour by re-evaluating the syscall number
after the tracepoint"
* tag 'core-entry-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Respect changes to system call number by trace_sys_enter()
Linus Torvalds [Sat, 23 Mar 2024 16:21:26 +0000 (09:21 -0700)]
Merge tag 'powerpc-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
- Handle errors in mark_rodata_ro() and mark_initmem_nx()
- Make struct crash_mem available without CONFIG_CRASH_DUMP
Thanks to Christophe Leroy and Hari Bathini.
* tag 'powerpc-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kdump: Split KEXEC_CORE and CRASH_DUMP dependency
powerpc/kexec: split CONFIG_KEXEC_FILE and CONFIG_CRASH_DUMP
kexec/kdump: make struct crash_mem available without CONFIG_CRASH_DUMP
powerpc: Handle error in mark_rodata_ro() and mark_initmem_nx()
Linus Torvalds [Sat, 23 Mar 2024 16:17:03 +0000 (09:17 -0700)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a misuse of kernel-doc comment
- use "Call trace:" for backtraces like other architectures
- implement copy_from_kernel_nofault_allowed() to fix a LKDTM test
- add a "cut here" line for prefetch aborts
- remove unnecessary Kconfing entry for FRAME_POINTER
- remove iwmmxy support for PJ4/PJ4B cores
- use bitfield helpers in ptrace to improve readabililty
- check if folio is reserved before flushing
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
ARM: 9354/1: ptrace: Use bitfield helpers
ARM: 9352/1: iwmmxt: Remove support for PJ4/PJ4B cores
ARM: 9353/1: remove unneeded entry for CONFIG_FRAME_POINTER
ARM: 9351/1: fault: Add "cut here" line for prefetch aborts
ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()
ARM: 9349/1: unwind: Add missing "Call trace:" line
ARM: 9334/1: mm: init: remove misuse of kernel-doc comment
Linus Torvalds [Sat, 23 Mar 2024 15:43:21 +0000 (08:43 -0700)]
Merge tag 'hardening-v6.9-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more hardening updates from Kees Cook:
- CONFIG_MEMCPY_SLOW_KUNIT_TEST is no longer needed (Guenter Roeck)
- Fix needless UTF-8 character in arch/Kconfig (Liu Song)
- Improve __counted_by warning message in LKDTM (Nathan Chancellor)
- Refactor DEFINE_FLEX() for default use of __counted_by
- Disable signed integer overflow sanitizer on GCC < 8
* tag 'hardening-v6.9-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lkdtm/bugs: Improve warning message for compilers without counted_by support
overflow: Change DEFINE_FLEX to take __counted_by member
Revert "kunit: memcpy: Split slow memcpy tests into MEMCPY_SLOW_KUNIT_TEST"
arch/Kconfig: eliminate needless UTF-8 character in Kconfig help
ubsan: Disable signed integer overflow sanitizer on GCC < 8
Thomas Gleixner [Fri, 22 Mar 2024 18:56:39 +0000 (19:56 +0100)]
x86/mpparse: Register APIC address only once
The APIC address is registered twice. First during the early detection and
afterwards when actually scanning the table for APIC IDs. The APIC and
topology core warn about the second attempt.
Thomas Gleixner [Fri, 22 Mar 2024 18:56:38 +0000 (19:56 +0100)]
x86/topology: Handle the !APIC case gracefully
If there is no local APIC enumerated and registered then the topology
bitmaps are empty. Therefore, topology_init_possible_cpus() will die with
a division by zero exception.
Prevent this by registering a fake APIC id to populate the topology
bitmap. This also allows to use all topology query interfaces
unconditionally. It does not affect the actual APIC code because either
the local APIC address was not registered or no local APIC could be
detected.
Fixes: f1f758a80516 ("x86/topology: Add a mechanism to track topology via APIC IDs") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20240322185305.242709302@linutronix.de
Thomas Gleixner [Fri, 22 Mar 2024 18:56:35 +0000 (19:56 +0100)]
x86/cpu: Ensure that CPU info updates are propagated on UP
The boot sequence evaluates CPUID information twice:
1) During early boot
2) When finalizing the early setup right before
mitigations are selected and alternatives are patched.
In both cases the evaluation is stored in boot_cpu_data, but on UP the
copying of boot_cpu_data to the per CPU info of the boot CPU happens
between #1 and #2. So any update which happens in #2 is never propagated to
the per CPU info instance.
Consolidate the whole logic and copy boot_cpu_data right before applying
alternatives as that's the point where boot_cpu_data is in it's final
state and not supposed to change anymore.
This also removes the voodoo mb() from smp_prepare_cpus_common() which
had absolutely no purpose.
Fixes: 71eb4893cfaf ("x86/percpu: Cure per CPU madness on UP") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20240322185305.127642785@linutronix.de
Nathan Chancellor [Thu, 21 Mar 2024 20:18:17 +0000 (13:18 -0700)]
lkdtm/bugs: Improve warning message for compilers without counted_by support
The current message for telling the user that their compiler does not
support the counted_by attribute in the FAM_BOUNDS test does not make
much sense either grammatically or semantically. Fix it to make it
correct in both aspects.
Kees Cook [Wed, 6 Mar 2024 23:51:36 +0000 (15:51 -0800)]
overflow: Change DEFINE_FLEX to take __counted_by member
The norm should be flexible array structures with __counted_by
annotations, so DEFINE_FLEX() is updated to expect that. Rename
the non-annotated version to DEFINE_RAW_FLEX(), and update the
few existing users. Additionally add selftests for the macros.
Linus Torvalds [Fri, 22 Mar 2024 20:31:07 +0000 (13:31 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"The vfs has long had a write lifetime hint mechanism that gives the
expected longevity on storage of the data being written. f2fs was the
original consumer of this and used the hint for flash data placement
(mostly to avoid write amplification by placing objects with similar
lifetimes in the same erase block).
More recently the SCSI based UFS (Universal Flash Storage) drivers
have wanted to take advantage of this as well, for the same reasons as
f2fs, necessitating plumbing the write hints through the block layer
and then adding it to the SCSI core.
The vfs write_hints already taken plumbs this as far as block and this
completes the SCSI core enabling based on a recently agreed reuse of
the old write command group number. The additions to the scsi_debug
driver are for emulating this property so we can run tests on it in
the absence of an actual UFS device"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Maintain write statistics per group number
scsi: scsi_debug: Implement GET STREAM STATUS
scsi: scsi_debug: Implement the IO Advice Hints Grouping mode page
scsi: scsi_debug: Allocate the MODE SENSE response from the heap
scsi: scsi_debug: Rework subpage code error handling
scsi: scsi_debug: Rework page code error handling
scsi: scsi_debug: Support the block limits extension VPD page
scsi: scsi_debug: Reduce code duplication
scsi: sd: Translate data lifetime information
scsi: scsi_proto: Add structures and constants related to I/O groups and streams
scsi: core: Query the Block Limits Extension VPD page
Linus Torvalds [Fri, 22 Mar 2024 19:46:07 +0000 (12:46 -0700)]
Merge tag 'block-6.9-20240322' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Make an informative message less ominous (Keith)
- Enhanced trace decoding (Guixin)
- TCP updates (Hannes, Li)
- Fabrics connect deadlock fix (Chunguang)
- Platform API migration update (Uwe)
- A new device quirk (Jiawei)
- Remove dead assignment in fd (Yufeng)
* tag 'block-6.9-20240322' of git://git.kernel.dk/linux:
nvmet-rdma: remove NVMET_RDMA_REQ_INVALIDATE_RKEY flag
nvme: remove redundant BUILD_BUG_ON check
floppy: remove duplicated code in redo_fd_request()
nvme/tcp: Add wq_unbound modparam for nvme_tcp_wq
nvme-tcp: Export the nvme_tcp_wq to sysfs
drivers/nvme: Add quirks for device 126f:2262
nvme: parse format command's lbafu when tracing
nvme: add tracing of reservation commands
nvme: parse zns command's zsa and zrasf to string
nvme: use nvme_disk_is_ns_head helper
nvme: fix reconnection fail due to reserved tag allocation
nvmet: add tracing of zns commands
nvmet: add tracing of authentication commands
nvme-apple: Convert to platform remove callback returning void
nvmet-tcp: do not continue for invalid icreq
nvme: change shutdown timeout setting message
projects / linux.git / log