David Galiffi [Mon, 24 Jun 2019 14:34:13 +0000 (10:34 -0400)]
drm/amd/display: Synchronous DisplayPort Link Training
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Improve sharing of HUBBUB register lists
Add DCN20 common register list that contains registers shared
between DCN20 generations.
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bayan Zabihiyan [Wed, 10 Jul 2019 20:00:53 +0000 (16:00 -0400)]
drm/amd/display: Fix frames_to_insert math
[Why]
The math on deciding on how many
"frames to insert" sometimes sent us over the max refresh rate.
Also integer overflow can occur if we have high refresh rates.
[How]
Instead of clipping the frame duration such that it doesn’t go below the min,
just remove a frame from the number of frames to insert. +
Use unsigned long long for intermediate calculations to prevent
integer overflow.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Fri, 12 Jul 2019 14:52:54 +0000 (10:52 -0400)]
drm/amd/display: fix issue where 252-255 values are clipped
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Wed, 10 Jul 2019 22:35:18 +0000 (18:35 -0400)]
drm/amd/display: reset hdmi tmds rate and data scramble on pipe reset
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Wed, 10 Jul 2019 22:31:38 +0000 (18:31 -0400)]
drm/amd/display: reset drr programming on pipe reset
[why]
drr is still enabled after driver is unloaded causing black screen
[how]
disable drr during pipe reset.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Tue, 25 Jun 2019 23:08:50 +0000 (19:08 -0400)]
drm/amd/display: Add DFS reference clock field
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Sat, 22 Jun 2019 22:52:41 +0000 (18:52 -0400)]
drm/amd/display: Add PIXEL_RATE control regs for more instances
For use by future ASICs
Signed-off-by: Sung Lee <sung.lee@amd.com> Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 9 Aug 2019 15:27:21 +0000 (17:27 +0200)]
drm/scheduler: use job count instead of peek
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Monk.liu@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 08:52:04 +0000 (16:52 +0800)]
drm/amdgpu: use exiting amdgpu_ctx_total_num_entities function
simplify driver code.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 08:48:28 +0000 (16:48 +0800)]
drm/amdgpu: fix typo error amdgput -> amdgpu
fix typo error:
change function name from "amdgput_ctx_total_num_entities" to
"amdgpu_ctx_total_num_entities".
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 02:25:25 +0000 (10:25 +0800)]
drm/amd/powerplay: fix message of SetHardMinByFreq failed when feature is disabled
the direct send message to smc to set hard clokc will failed
when smc clock dpm feature is disabled.
so use function of smu_set_hard_freq_range to replace it.
the function will check feature enablement.
eg: when uclk (mclk) dpm feature is disabled on navi10
[ 300.675901] amdgpu: [powerplay] failed send message: SetHardMinByFreq(28)
param: 0x00020064 response 0xfffffffb
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chengming Gui [Mon, 12 Aug 2019 02:06:34 +0000 (10:06 +0800)]
drm/amd/powerplay: remove redundancy debug log about smu unsupported features
remove redundancy debug log about smu unsupported features
Signed-off-by: Chengming Gui <Jack.Gui@amd.com> Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christoph Hellwig [Thu, 15 Aug 2019 07:27:03 +0000 (09:27 +0200)]
drm/amdgpu: simplify and cleanup setting the dma mask
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christoph Hellwig [Thu, 15 Aug 2019 07:27:02 +0000 (09:27 +0200)]
drm/radeon: simplify and cleanup setting the dma mask
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christoph Hellwig [Thu, 15 Aug 2019 07:27:01 +0000 (09:27 +0200)]
drm/amdgpu: handle PCIe root ports with addressing limitations
amdgpu uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christoph Hellwig [Thu, 15 Aug 2019 07:27:00 +0000 (09:27 +0200)]
drm/radeon: handle PCIe root ports with addressing limitations
radeon uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com> Reported-by: Atish Patra <Atish.Patra@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 13:21:57 +0000 (09:21 -0400)]
drm/amdgpu: add VCN2.0 to Renoir IP blocks
Thus enable VCN2.0 for Renoir
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 14:14:17 +0000 (10:14 -0400)]
drm/amdgpu: enable Doorbell support for Renoir (v2)
Add VCN range aperture to NBIO 7.0
v2: rebase (Alex)
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 13:01:51 +0000 (09:01 -0400)]
drm/amdgpu: enable Renoir VCN firmware loading
By adding new Renoir VCN firmware
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aaron Liu [Wed, 24 Jul 2019 18:53:17 +0000 (13:53 -0500)]
drm/amdgpu: fix no interrupt issue for renoir emu
In renoir's ih model, there's a change in mmIH_CHICKEN
register, that limits IH to use physical address directly.
Those chicken bits need to be programmed first.
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Aaron Liu <aaron.liu@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The check on ret is duplicated in two places, it is redundant code.
Remove it.
Addresses-Coverity: ("Logically dead code") Fixes: b94afb61cdae ("drm/amd/powerplay: honor hw limit on fetching metrics data for navi10") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pierre-Eric Pelloux-Prayer [Tue, 6 Aug 2019 16:27:26 +0000 (18:27 +0200)]
drm/amdgpu: fix gfx9 soft recovery
The SOC15_REG_OFFSET() macro wasn't used, making the soft recovery fail.
v2: use WREG32_SOC15 instead of WREG32 + SOC15_REG_OFFSET
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Le Ma [Thu, 8 Aug 2019 06:54:12 +0000 (14:54 +0800)]
drm/amdgpu: split athub clock gating from mmhub
Untie the bind of get/set athub CG state from mmhub, for cosmetic fix and Asic
not using mmhub 1.0. Besides, also fix wrong athub CG state in amdgpu_pm_info.
Signed-off-by: Le Ma <le.ma@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Wed, 24 Jul 2019 15:56:28 +0000 (17:56 +0200)]
drm/amdgpu: Update pitch on page flips without DC as well
DC already handles this correctly since amdgpu minor version 31. Bump
the minor version again so that xf86-video-amdgpu can take advantage of
this working without DC as well now.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Francis [Wed, 7 Aug 2019 14:25:48 +0000 (10:25 -0400)]
drm/amd/display: Remove drm_dsc_dc.c
This file was accidentally added to the driver during
Navi promotion
Nothing includes it. No makefile attempts to compile it, and
it would fail compilation if they tried
Remove it
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com>w Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Mon, 12 Aug 2019 04:20:21 +0000 (14:20 +1000)]
Merge tag 'drm-next-5.4-2019-08-09' of git://people.freedesktop.org/~agd5f/linux into drm-next
drm-next-5.4-2019-08-09:
Same as drm-next-5.4-2019-08-06, but with the
readq/writeq stuff fixed and 5.3-rc3 backmerged.
amdgpu:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- Enable mclk DPM for Navi
- Misc DC display fixes
- Add perfmon support for DF
- Add scatter/gather display support for Raven
- Improve SMU handling for GPU reset
- RAS support for GFX
- Drop last of drmP.h
- Add support for wiping memory on buffer release
- Allow cursor async updates for fb swaps
- Misc fixes and cleanups
amdkfd:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- CWSR trap handlers updates for gfx9, 10
- Drop last of drmP.h
- Update MAINTAINERS
radeon:
- Misc fixes and cleanups
- Make kexec more reliable by tearing down the GPU
ttm:
- Add release_notify callback
uapi:
- Add wipe memory on release flag for buffer creation
Tao Zhou [Fri, 9 Aug 2019 07:57:51 +0000 (15:57 +0800)]
drm/amdgpu: remove RREG64/WREG64
atomic 64 bits REG operations are useless currently
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tao Zhou [Fri, 9 Aug 2019 07:57:50 +0000 (15:57 +0800)]
drm/amdgpu: implement UMC 64 bits REG operations
implement 64 bits operations via 32 bits interface
v2: make use of lower_32_bits() and upper_32_bits() macros
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tao Zhou [Wed, 7 Aug 2019 02:28:54 +0000 (10:28 +0800)]
drm/amdgpu: replace readq/writeq with atomic64 operations
what we really want is a read or write that is guaranteed to be 64 bits
at a time, atomic64 operations are supported on all architectures
Signed-off-by: Tao Zhou <tao.zhou1@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Fri, 9 Aug 2019 06:04:15 +0000 (16:04 +1000)]
Merge tag 'drm-misc-next-2019-08-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
John Keeping [Wed, 3 Jul 2019 09:51:11 +0000 (10:51 +0100)]
drm/rockchip: fix VOP_WIN_GET macro
Commit 9a61c54b9bff ("drm/rockchip: vop: group vop registers") seems to
have unintentionally changed the defintion of this macro. Since it is
unused, this was not spotted but any attempt to use it results in
compilation errors.
Emil Velikov [Mon, 27 May 2019 08:17:35 +0000 (09:17 +0100)]
drm/msm: drop DRM_AUTH usage from the driver
The authentication can be circumvented, by design, by using the render
node.
From the driver POV there is no distinction between primary and render
nodes, thus we can drop the token.
Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: freedreno@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Emil Velikov <emil.velikov@collabora.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190527081741.14235-7-emil.l.velikov@gmail.com
projects / users / willy / xarray.git / log