Russell King [Fri, 22 Feb 2019 11:31:41 +0000 (11:31 +0000)]
net: phylink: update mac_config() documentation
A detail for mac_config() had been missed in the documentation for the
method - it is expected that the method will update the MAC to the
settings, rather than completely reprogram the MAC on each call.
Update the documentation for this method for this detail.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 22 Feb 2019 07:23:04 +0000 (08:23 +0100)]
net: phy: let genphy_c45_read_abilities also check aneg capability
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Feb 2019 17:47:07 +0000 (09:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Roopa Prabhu [Sun, 24 Feb 2019 06:25:12 +0000 (22:25 -0800)]
trace: events: neigh_update: print new state in string format
Also, extend neigh_state_str to include neigh dummy states
noarp and permanent
Fixes: 9c03b282badb ("trace: events: add a few neigh tracepoints") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Sun, 24 Feb 2019 00:11:15 +0000 (01:11 +0100)]
net: phy: realtek: Dummy IRQ calls for RTL8366RB
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Feb 2019 21:24:59 +0000 (13:24 -0800)]
net/x25: fix a race in x25_bind()
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
Fixes: 90c27297a9bf ("X.25 remove bkl in bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 22 Feb 2019 13:22:32 +0000 (21:22 +0800)]
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0") Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thadeu Lima de Souza Cascardo [Fri, 22 Feb 2019 10:27:41 +0000 (07:27 -0300)]
selftests: fib_tests: sleep after changing carrier. again.
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 22 Feb 2019 22:50:49 +0000 (23:50 +0100)]
net: phy: don't change modes we don't care about in genphy_c45_read_lpa
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 22 Feb 2019 22:49:54 +0000 (23:49 +0100)]
net: phy: aquantia: add support for auto-negotiation configuration
Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 22 Feb 2019 22:48:14 +0000 (23:48 +0100)]
net: phy: aquantia: remove false 5G and 10G speed ability for AQCS109
AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: Add support for new port types and speeds for Spectrum-2
Shalom says:
This patchset adds support for new port types and speeds for Spectrum-2.
Patch #1 + #2 removes an unsupported PTYS field and a duplicate link
mode entry.
Patch #3 queries port's connector type from firmware instead of deriving
it from port admin state.
Patch #4 renames functions which relate to port type-speed to be
Spectrum-1 specific.
Patch #5 defines port type-speed operations and applies it for
Spectrum-1.
Patch #6 + #7 are small renaming and cosmetic changes.
Patch #8 adds new port type-speed fields for PTYS register. These new
fields extend the existing ones in order to support more types and
speeds.
Patch #9 adds Spectrum-2 support for port type-speed operations.
Patch #10 adds Spectrum-2 new port types and speeds.
For Spectrum-2, the user must configure all the types per speed if he /
she wants a specific speed to be advertised. For example, if the user
wants to advertise 100Gbps 4-lanes speed, the following ethtool bits
should be advertised:
Supported ethtool bits for 100Gbps 4-lanes:
0x1000000000 100000baseKR4 Full
0x2000000000 100000baseSR4 Full
0x4000000000 100000baseCR4 Full
0x8000000000 100000baseLR4_ER4 Full
Shalom Toledo [Fri, 22 Feb 2019 13:56:45 +0000 (13:56 +0000)]
mlxsw: spectrum: Add Spectrum-2 ASIC port type-speed operations
Add Spectrum-2 ASIC port type-speed operations.
Since multiple ethtool link modes are represented using a single bit in the
ASIC, the driver forces the user to configure all types per a specific
speed. For example, if the user wants to advertise 100Gbps 4-lanes speed,
he should advertise all the types of 100Gbps 4-lanes speed that are
supported by the ASIC as shown below:
Supported ethtool bits for 100Gbps 4-lanes:
0x1000000000 100000baseKR4 Full
0x2000000000 100000baseSR4 Full
0x4000000000 100000baseCR4 Full
0x8000000000 100000baseLR4_ER4 Full
Command for advertising 100Gbps 4-lanes:
ethtool -s enp3s0np1 advertise 0xF000000000
Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Fri, 22 Feb 2019 13:56:44 +0000 (13:56 +0000)]
mlxsw: reg: Add new port type-speed fields for PTYS register
PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Fri, 22 Feb 2019 06:57:23 +0000 (14:57 +0800)]
net: set static variable an initial value in atl2_probe()
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Feb 2019 21:44:58 +0000 (13:44 -0800)]
Merge branch 'net-Wformat-fixes'
Florian Fainelli says:
====================
-Wformat fixes
This is a collection of some -Wformat fixes found during build, nothing
critical, but nice to have for people turning on more warnings with
their builds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 22 Feb 2019 04:09:29 +0000 (20:09 -0800)]
veth: Fix -Wformat-truncation
Provide a precision hint to snprintf() in order to eliminate a
-Wformat-truncation warning provided below. A maximum of 11 characters
is allowed to reach a maximum of 32 - 1 characters given a possible
maximum value of queues using up to UINT_MAX which occupies 10
characters. Incidentally 11 is the number of characters for
"xdp_packets" which is the largest string we append.
drivers/net/veth.c: In function 'veth_get_strings':
drivers/net/veth.c:118:47: warning: '%s' directive output may be
truncated writing up to 31 bytes into a region of size between 12 and 21
[-Wformat-truncation=]
snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
^~
drivers/net/veth.c:118:5: note: 'snprintf' output between 12 and 52
bytes into a destination of size 32
snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
i, veth_rq_stats_desc[j].desc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 22 Feb 2019 04:09:28 +0000 (20:09 -0800)]
e1000e: Fix -Wformat-truncation warnings
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_prio_stats[i].str, prio);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_tc_stats[i].str, tc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Fri, 22 Feb 2019 03:23:19 +0000 (12:23 +0900)]
bpfilter: re-add header search paths to tools include to fix build error
I thought header search paths to tools/include(/uapi) were unneeded,
but it looks like a build error occurs depending on the compiler.
Commit 303a339f30a9 ("bpfilter: remove extra header search paths for
bpfilter_umh") reintroduced the build error fixed by commit ae40832e53c3
("bpfilter: fix a build err").
Apology for the breakage, and thanks to Guenter for reporting this.
Fixes: 303a339f30a9 ("bpfilter: remove extra header search paths for bpfilter_umh") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier [Thu, 21 Feb 2019 16:54:11 +0000 (17:54 +0100)]
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 17:48:01 +0000 (09:48 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 01:46:30 +0000 (17:46 -0800)]
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Linus Torvalds [Sat, 23 Feb 2019 00:31:26 +0000 (16:31 -0800)]
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
Daniel Borkmann [Fri, 22 Feb 2019 23:03:44 +0000 (00:03 +0100)]
bpf, doc: add bpf list as secondary entry to maintainers file
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Sat, 23 Feb 2019 00:12:01 +0000 (16:12 -0800)]
Merge branch 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
Linus Torvalds [Sat, 23 Feb 2019 00:09:55 +0000 (16:09 -0800)]
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
David S. Miller [Sat, 23 Feb 2019 00:05:12 +0000 (16:05 -0800)]
Merge branch 'udp-a-few-fixes'
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:44:00 +0000 (17:44 +0100)]
udp: fix possible user after free in error handler
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:59 +0000 (17:43 +0100)]
udpv6: fix possible user after free in error handler
Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:58 +0000 (17:43 +0100)]
fou6: fix proto error handler argument type
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:57 +0000 (17:43 +0100)]
udpv6: add the required annotation to mib type
In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 21 Feb 2019 14:42:01 +0000 (22:42 +0800)]
mdio_bus: Fix use-after-free on device_register fails
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: at803x: Update delays for RGMII modes
Peter[1] reported that patch cd28d1d6e52e: ("net: phy: at803x: Disable
phy delay for RGMII mode") caused regression on am335x-evmsk board.
This board expects the Phy delay to be enabled but specified RGMII mode
which refers to delays being disabled. So fix this by disabling delay only
for RGMII mode and enable for RGMII_ID and RGMII_TXID/RXID modes.
While at it, as pointed by Dave, don't inline the helpers.
Vinod Koul [Thu, 21 Feb 2019 10:23:15 +0000 (15:53 +0530)]
net: phy: at803x: disable delay only for RGMII mode
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode") Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org> Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vinod Koul [Thu, 21 Feb 2019 10:23:14 +0000 (15:53 +0530)]
net: phy: at803x: don't inline helpers
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org> Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com> Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 21 Feb 2019 05:37:42 +0000 (21:37 -0800)]
net_sched: initialize net pointer inside tcf_exts_init()
For tcindex filter, it is too late to initialize the
net pointer in tcf_exts_validate(), as tcf_exts_get_net()
requires a non-NULL net pointer. We can just move its
initialization into tcf_exts_init(), which just requires
an additional parameter.
This makes the code in tcindex_alloc_perfect_hash()
prettier.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalash Nainwal [Thu, 21 Feb 2019 00:23:04 +0000 (16:23 -0800)]
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:32 +0000 (19:07 -0500)]
bnxt_en: Wait longer for the firmware message response to complete.
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:31 +0000 (19:07 -0500)]
bnxt_en: Fix typo in firmware message timeout logic.
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang [Fri, 22 Feb 2019 22:36:04 +0000 (22:36 +0000)]
nfp: bpf: fix ALU32 high bits clearance bug
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator") Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Huy Nguyen [Mon, 21 Jan 2019 22:22:05 +0000 (16:22 -0600)]
net/mlx5: E-Switch, Add support for VEPA in legacy mode.
In Virtual Ethernet Port Aggregator (VEPA) mode, the packet skips
the system internal virtual switch and forwards to external network
switch. In Mellanox HCA case, the virtual switch is the HCA's Eswitch.
To support this, an new FDB flow table are created with level 0 and
linked to the existing FDB flow table in legacy mode. By default,
VEPA is turned off and this FDB flow table is empty. When VEPA is
turned on, two rules are created. One rule to forward on uplink vport
traffic to the legacy FDB. The other rule forward all other traffic
to uplink vport.
Other design alternatives were not chosen as explained below:
1. Create a forward rule in ACL flow table (most efficient design).
This approach is the not chosen because firmware does not support
forward rule to uplink vport (0xffff) for ACL flow table.
2. Add additional source port criteria in all the FDB rules to make the
FDB rules to be received rules only. This approach is not chosen because
it is not efficient as there can many rules in the FDB and VEPA mode
cannot be controlled per vport.
3. Add a highest prioirty flow group in the existing legacy FDB Flow
Table instead of a new flow table. This approoach does not work because the
new flow group has the same match criteria as the promiscuous flow group
and mlx5_add_flow_rules does not allow specifying flow group.
Eran Ben Elisha [Wed, 20 Feb 2019 10:10:48 +0000 (12:10 +0200)]
net/mlx5e: Fix return status of TX reporter timeout recover
In case of lost interrupt recover, we shall return success. Fix that.
Fixes: 7d91126b1aea ("net/mlx5e: Add tx timeout support for mlx5e tx reporter") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reported-by: Maria Pasechnik <mariap@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Tue, 19 Feb 2019 13:26:04 +0000 (15:26 +0200)]
net/mlx5e: Re-add support for TX timeout when TX reporter is not valid
When TX reporter was introduced, it took ownership over TX timeout error
handling. this introduced a regression in case TX reporter is not valid
(NET_DEVLINK is not set, or devlink_health_reporter_create failure).
Fix mlx5e_tx_reporter_timeout function so it can be called at all times.
In addition, remove a warning print that indicates that a TX timeout won't
be handled in case of no valid TX reporter.
Fixes: 7d91126b1aea ("net/mlx5e: Add tx timeout support for mlx5e tx reporter") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Tue, 19 Feb 2019 13:05:12 +0000 (15:05 +0200)]
net/mlx5e: Fix warn print in case of TX reporter creation failure
Print warning message in case of TX reporter creation failure, only if the
return value is ERR_PTR type. NULL pointer return indicates that
NET_DEVLINK is not set, and the warning print can be skipped.
Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Mon, 14 Jan 2019 08:07:44 +0000 (10:07 +0200)]
net/mlx5e: Fix GRE key by controlling port tunnel entropy calculation
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff193 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Sun, 20 Jan 2019 20:33:19 +0000 (22:33 +0200)]
net/mlx5: Introduce tunnel entropy control in PCMR register
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Mon, 21 Jan 2019 07:00:42 +0000 (09:00 +0200)]
net/mlx5: Use read-modify-write when changing PCMR register values
Currently changing a PCMR field is done by setting the field in a
zeroed buffer, zeroing other unrelated fields.
Fix this behaviour by modifying only the required field after first
reading the current register values, as a pre-step towards using more
fields in PCMR register.
Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Fri, 22 Feb 2019 20:56:24 +0000 (12:56 -0800)]
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series contains the implementation of the RFC that was posted
on this mailing list previously:
https://www.spinics.net/lists/netdev/msg541709.html
It fixes having incorrect skb->transport_header values in cases when
dissect fails. Having correct values set by the kernel fixes mlx5
operation and allows to remove some unnecessary code flows in mlx5.
v2 changes:
- Rebase against the fresh net-next.
- Don't return bool from skb_probe_transport_header (and don't rename
the function).
- WARN_ON_ONCE and error path in case of GSO without the L4 header.
====================
Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:40:05 +0000 (12:40 +0000)]
net/mlx5e: Trust kernel regarding transport offset
After AF_PACKET is fixed to calculate the transport header offset
correctly, trust the value set by the kernel. If the offset wasn't set,
it means there is no transport header in the packet.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:40:04 +0000 (12:40 +0000)]
net/mlx5e: Remove the wrong assumption about transport offset
skb_transport_offset() == 0 is not a special value. The only special
value is when skb->transport_header is ~0U, and it's checked by
skb_transport_header_was_set().
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:40:02 +0000 (12:40 +0000)]
net/packet: Remove redundant skb->protocol set
c72219b75f introduced tpacket_set_protocol that parses the Ethernet L2
header and sets skb->protocol if it's unset. It is no longer needed
since the introduction of packet_parse_headers. In case of SOCK_RAW and
unset skb->protocol, packet_parse_headers asks the driver to tell the
protocol number, and it's implemented for all Ethernet devices. As the
old function supported only Ethernet, no functionality is lost.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:40:01 +0000 (12:40 +0000)]
net/packet: Ask driver for protocol if not provided by user
If a socket was created with socket(AF_PACKET, SOCK_RAW, 0), the
protocol number is unavailable. Try to ask the driver to extract it from
the L2 header in order for skb_try_probe_transport_header to succeed.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:39:59 +0000 (12:39 +0000)]
net/ethernet: Add parse_protocol header_ops support
The previous commit introduced parse_protocol callback which should
extract the protocol number from the L2 header. Make all Ethernet
devices support it.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:39:58 +0000 (12:39 +0000)]
net: Introduce parse_protocol header_ops callback
Introduce a new optional header_ops callback called parse_protocol and a
wrapper function dev_parse_header_protocol, similar to dev_parse_header.
The new callback's purpose is to extract the protocol number from the L2
header, the format of which is known to the driver, but not to the upper
layers of the stack.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Thu, 21 Feb 2019 12:39:57 +0000 (12:39 +0000)]
net: Don't set transport offset to invalid value
If the socket was created with socket(AF_PACKET, SOCK_RAW, 0),
skb->protocol will be unset, __skb_flow_dissect() will fail, and
skb_probe_transport_header() will fall back to the offset_hint, making
the resulting skb_transport_offset incorrect.
If, however, there is no transport header in the packet,
transport_header shouldn't be set to an arbitrary value.
Fix it by leaving the transport offset unset if it couldn't be found, to
be explicit rather than to fill it with some wrong value. It changes the
behavior, but if some code relied on the old behavior, it would be
broken anyway, as the old one is incorrect.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 Feb 2019 20:52:23 +0000 (12:52 -0800)]
Merge tag 'mac80211-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have, of note:
* the massive patch series for multi-BSSID support, I ended up
applying that through a side branch to record some details
* CSA improvements
* HE (802.11ax) updates to Draft 3.3
* strongly typed element iteration/etc. to make such code more
readable - this came up in particular in multi-BSSID
* rhashtable conversion patches from Herbert
Along, as usual, with various fixes and improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 Feb 2019 20:51:21 +0000 (12:51 -0800)]
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 20 Feb 2019 22:58:50 +0000 (14:58 -0800)]
Documentation: networking: switchdev: Update port parent ID section
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID") Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series supports having VLAN devices on top of DSA/switch
ports while the switch has VLAN filtering globally turned on (as is the
case with Broadcom switches). Whether the switch does global or per-port
VLAN filtering, having VLAN entries for these VLAN devices is
beneficial.
We take care of a few possibly problematic cases:
- adding a VLAN device while there is an existing VLAN entry created by
a VLAN aware bridge. The entire bridge's VLAN database and not just
the specific bridge port is being checked to be safe and conserative
- adding a bridge VLAN entry when there is an existing VLAN device
created is also not possible because that would lead to the bridge
being able to manipulate the VLAN device's VID/attributes under its feet
- enslaving a VLAN device into a VLAN aware bridge since that duplicates
functionality already offered by the VLAN aware bridge
Here are the different test cases that were run to exercise this:
ip addr flush dev gphy
ip link add dev br0 type bridge
echo 1 > /sys/class/net/br0/bridge/vlan_filtering
ip link set dev gphy master br0
udhcpc -i br0
In order to properly support VLAN filtering being enabled/disabled on a
bridge, while having other ports being non bridge port members, we need
to support the ndo_vlan_rx_{add,kill}_vid callbacks in order to make
sure the non-bridge ports can continue receiving VLAN tags, even when
the switch is globally configured to do ingress/egress VID checking.
Since we can call dsa_port_vlan_{add,del} with a bridge_dev pointer
NULL, we now need to check that in these two functions.
We specifically deal with two possibly problematic cases:
- creating a bridge VLAN entry while there is an existing VLAN device
claiming that same VID
- creating a VLAN device while there is an existing bridge VLAN entry
with that VID
Those are both resolved with returning -EBUSY back to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 20 Feb 2019 22:35:38 +0000 (14:35 -0800)]
net: dsa: Deny enslaving VLAN devices into VLAN aware bridge
VLAN devices on top of a DSA network device which is already part of a
bridge and with said bridge being VLAN aware should not be allowed to be
enslaved into that bridge. For one, this duplicates functionality
offered by the VLAN aware bridge which supports tagged and untagged VLAN
frames processing and it would make things needlessly complex to e.g.:
propagate FDB/MDB accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jann Horn [Wed, 20 Feb 2019 21:34:54 +0000 (22:34 +0100)]
net: socket: add check for negative optlen in compat setsockopt
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 20 Feb 2019 20:25:26 +0000 (14:25 -0600)]
isdn_common: Mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/isdn/i4l/isdn_common.c: In function ‘isdn_wildmat’:
drivers/isdn/i4l/isdn_common.c:173:5: warning: this statement may fall through [-Wimplicit-fallthrough=]
p++;
~^~
drivers/isdn/i4l/isdn_common.c:174:3: note: here
default:
^~~~~~~
CC [M] drivers/leds/leds-lp8788.o
CC [M] drivers/gpu/drm/amd/amdgpu/../powerplay/smumgr/smu10_smumgr.o
drivers/isdn/i4l/isdn_common.c: In function ‘isdn_status_callback’:
drivers/isdn/i4l/isdn_common.c:729:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (divert_if)
^
drivers/isdn/i4l/isdn_common.c:732:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 20 Feb 2019 17:18:12 +0000 (18:18 +0100)]
ipv6: route: purge exception on removal
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nic: thunderx: fix communication races between VF & PF
The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.
After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.
Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.
This patch series is to address race condition with VF & PF communication.
Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
from int to void;
- 0007: update subject and remove unused variable 'netdev'
from nicvf_link_status_check_task() function;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: remove link change polling code and info from nicpf
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: move link state polling function to VF
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:44 +0000 (11:02 +0000)]
net: thunderx: add mutex to protect mailbox from concurrent calls for same VF
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / users / jedix / linux-maple.git / log