The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Callers are generally not supposed to check the return values from
debugfs functions. Debugfs functions never return NULL so this error
handling will never trigger. (Historically debugfs functions used to
return a mix of NULL and error pointers but it was eventually deemed too
complicated for something which wasn't intended to be used in normal
situations).
Delete all the error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Link: https://lore.kernel.org/r/20200826113759.GF393664@mwanda Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In gfs2_check_sb(), no validation checks are performed with regards to
the size of the superblock.
syzkaller detected a slab-out-of-bounds bug that was primarily caused
because the block size for a superblock was set to zero.
A valid size for a superblock is a power of 2 between 512 and PAGE_SIZE.
Performing validation checks and ensuring that the size of the superblock
is valid fixes this bug.
When we try to use file already used as a quota file again (for the same
or different quota type), strange things can happen. At the very least
lockdep annotations may be wrong but also inode flags may be wrongly set
/ reset. When the file is used for two quota types at once we can even
corrupt the file and likely crash the kernel. Catch all these cases by
checking whether passed file is already used as quota file and bail
early in that case.
This fixes occasional generic/219 failure due to lockdep complaint.
Reviewed-by: Andreas Dilger <adilger@dilger.ca> Reported-by: Ritesh Harjani <riteshh@linux.ibm.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20201015110330.28716-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rdc321x_wdt_probe(), rdc321x_wdt_device.queue is initialized
after misc_register(), hence if ioctl is called before its
initialization which can call rdc321x_wdt_start() function,
it will see an uninitialized value of rdc321x_wdt_device.queue,
hence initialize it before misc_register().
Also, rdc321x_wdt_device.default_ticks is accessed in reset()
function called from write callback, thus initialize it before
misc_register().
Found by Linux Driver Verification project (linuxtesting.org).
In p9_fd_create_unix, checking is performed to see if the addr (passed
as an argument) is NULL or not.
However, no check is performed to see if addr is a valid address, i.e.,
it doesn't entirely consist of only 0's.
The initialization of sun_server.sun_path to be equal to this faulty
addr value leads to an uninitialized variable, as detected by KMSAN.
Checking for this (faulty addr) and returning a negative error number
appropriately, resolves this issue.
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
The minus 1 is wrong, this branch should report 2048 bits of space.
With "-1" action, this only report 1024 bit of space.
This bug code returns wrong blocks, but it doesn't inflence bitmap logic:
1. Most callers focus this function return value (the counter of offset),
not the parameter blocks.
2. The bug is only triggered when hijacked is true or map is NULL.
the hijacked true condition is very rare.
the "map == null" only true when array is creating or resizing.
3. Even the caller gets wrong blocks, current code makes caller just to
call md_bitmap_get_counter() one more time.
Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.
These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.
Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.
However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.
This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.
This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.
Cc: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function should check the validity of the pxm value before using
it to index the pxm_to_node_map[] array.
Whilst hardening this code may be good in general, the main intent
here is to enable following patches that use this function to replace
acpi_map_pxm_to_node() for non SRAT usecases which should return
NO_NUMA_NODE for PXM entries not matching with those in SRAT.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Barry Song <song.bao.hua@hisilicon.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
uio_register_device() do two things.
1) get an uio id from a global pool, e.g. the id is <A>
2) create file nodes like /sys/class/uio/uio<A>
uio_unregister_device() do two things.
1) free the uio id <A> and return it to the global pool
2) free the file node /sys/class/uio/uio<A>
There is a situation is that one worker is calling uio_unregister_device(),
and another worker is calling uio_register_device().
If the two workers are X and Y, they go as below sequence,
1) X free the uio id <AAA>
2) Y get an uio id <AAA>
3) Y create file node /sys/class/uio/uio<AAA>
4) X free the file note /sys/class/uio/uio<AAA>
Then it will failed at the 3rd step and cause the phenomenon we saw as it
is creating a duplicated file node.
On my system the kernel processes the "kgdb_earlycon" parameter before
the "kgdbcon" parameter. When we setup "kgdb_earlycon" we'll end up
in kgdb_register_callbacks() and "kgdb_use_con" won't have been set
yet so we'll never get around to starting "kgdbcon". Let's remedy
this by detecting that the IO module was already registered when
setting "kgdb_use_con" and registering the console then.
As part of this, to avoid pre-declaring things, move the handling of
the "kgdbcon" further down in the file.
The .bss section for the h8300 is relatively small. A value of
CONFIG_LOG_BUF_SHIFT that is larger than 19 will create a static
printk ringbuffer that is too large. Limit the range appropriately
for the H8300.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20200812073122.25412-1-john.ogness@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com Signed-off-by: Sasha Levin <sashal@kernel.org>
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
tw5864-video.c:773:32: warning: The left expression of the compound
assignment is an uninitialized value.
The computed value will also be garbage
fintv->stepwise.max.numerator *= std_max_fps;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
stepwise.max is set with frameinterval, which comes from
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
The default RGB quantization range for BT.2020 is full range (just as for
all the other RGB pixel encodings), not limited range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT macro and documentation
accordingly.
Also mention that HSV is always full range and cannot be limited range.
When RGB BT2020 was introduced in V4L2 it was not clear whether it should
be limited or full range, but full range is the right (and consistent)
choice.
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
The realtime bitmap and summary files are regular files that are hidden
away from the directory tree. Since they're regular files, inode
inactivation will try to purge what it thinks are speculative
preallocations beyond the incore size of the file. Unfortunately,
xfs_growfs_rt forgets to update the incore size when it resizes the
inodes, with the result that inactivating the rt inodes at unmount time
will cause their contents to be truncated.
Fix this by updating the incore size when we change the ondisk size as
part of updating the superblock. Note that we don't do this when we're
allocating blocks to the rt inodes because we actually want those blocks
to get purged if the growfs fails.
This fixes corruption complaints from the online rtsummary checker when
running xfs/233. Since that test requires rmap, one can also trigger
this by growing an rt volume, cycling the mount, and creating rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is commit fdfeff0f9e3d ("arm64: hw_breakpoint: Handle inexact
watchpoint addresses") but ported to arm32, which has the same
problem.
This problem was found by Android CTS tests, notably the
"watchpoint_imprecise" test [1]. I tested locally against a copycat
(simplified) version of the test though.
@blkno in f2fs_ra_meta_pages could exceed max segment count, causing panic
in following sanity check in current_sit_addr(), add check condition to
avoid this issue.
The de facto (and apparently uncommented) standard for using an mm had,
thanks to this code in sparc if nothing else, been that you must have a
reference on mm_users *and that reference must have been obtained with
mmget()*, i.e., from a thread with a reference to mm_users that had used
the mm.
The introduction of mmget_not_zero() in commit d2005e3f41d4
("userfaultfd: don't pin the user memory in userfaultfd_file_create()")
allowed mm_count holders to aoperate on user mappings asynchronously
from the actual threads using the mm, but they were not to load those
mappings into their TLB (i.e., walking vmas and page tables is okay,
kthread_use_mm() is not).
io_uring 2b188cc1bb857 ("Add io_uring IO interface") added code which
does a kthread_use_mm() from a mmget_not_zero() refcount.
The problem with this is code which previously assumed mm == current->mm
and mm->mm_users == 1 implies the mm will remain single-threaded at
least until this thread creates another mm_users reference, has now
broken.
arch/sparc/kernel/smp_64.c:
if (atomic_read(&mm->mm_users) == 1) {
cpumask_copy(mm_cpumask(mm), cpumask_of(cpu));
goto local_flush_and_out;
}
vs fs/io_uring.c
if (unlikely(!(ctx->flags & IORING_SETUP_SQPOLL) ||
!mmget_not_zero(ctx->sqo_mm)))
return -EFAULT;
kthread_use_mm(ctx->sqo_mm);
mmget_not_zero() could come in right after the mm_users == 1 test, then
kthread_use_mm() which sets its CPU in the mm_cpumask. That update could
be lost if cpumask_copy() occurs afterward.
I propose we fix this by allowing mmget_not_zero() to be a first-class
reference, and not have this obscure undocumented and unchecked
restriction.
The basic fix for sparc64 is to remove its mm_cpumask clearing code. The
optimisation could be effectively restored by sending IPIs to mm_cpumask
members and having them remove themselves from mm_cpumask. This is more
tricky so I leave it as an exercise for someone with a sparc64 SMP.
powerpc has a (currently similarly broken) example.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
powerpc uses IPIs in some situations to switch a kernel thread away
from a lazy tlb mm, which is subject to the TLB flushing race
described in the changelog introducing ARCH_WANT_IRQS_OFF_ACTIVATE_MM.
When building with W=1 we get the following warning:
arch/powerpc/platforms/powernv/smp.c: In function ‘pnv_smp_cpu_kill_self’:
arch/powerpc/platforms/powernv/smp.c:276:16: error: suggest braces around
empty body in an ‘if’ statement [-Werror=empty-body]
276 | cpu, srr1);
| ^
cc1: all warnings being treated as errors
The full context is this block:
if (srr1 && !generic_check_cpu_restart(cpu))
DBG("CPU%d Unexpected exit while offline srr1=%lx!\n",
cpu, srr1);
When building with DEBUG undefined DBG() expands to nothing and GCC emits
the warning due to the lack of braces around an empty statement.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200804005410.146094-2-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If should_futex_fail() returns true in futex_wake_pi(), then the 'ret'
variable is set to -EFAULT and then immediately overwritten. So the failure
injection is non-functional.
Fix it by actually leaving the function and returning -EFAULT.
The Fixes tag is kinda blury because the initial commit which introduced
failure injection was already sloppy, but the below mentioned commit broke
it completely.
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
Memory state around the buggy address: ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC 10 optimizes the scheduler code differently than its predecessors.
When CONFIG_DEBUG_SECTION_MISMATCH=y, the Makefile forces GCC not
to inline some functions (-fno-inline-functions-called-once). Before GCC
10, "no-inlined" __schedule() starts with the usual prologue:
push %bp
mov %sp, %bp
So the ORC unwinder simply picks stack pointer from %bp and
unwinds from __schedule() just perfectly:
But now, with GCC 10, there is no %bp prologue in __schedule():
$ cat /proc/1/stack
<nothing>
The ORC entry of the point in __schedule() is:
sp:sp+88 bp:last_sp-48 type:call end:0
In this case, nobody subtracts sizeof "struct inactive_task_frame" in
__unwind_start(). The struct is put on the stack by __switch_to_asm() and
only then __switch_to_asm() stores %sp to task->thread.sp. But we start
unwinding from a point in __schedule() (stored in frame->ret_addr by
'call') and not in __switch_to_asm().
0xffffffff9376cad0 is __schedule+0x1f0 (after the call to
__switch_to_asm). Now follow those 88 bytes from the ORC entry (sp+88).
The entry is correct, __schedule() really pushes 48 bytes (8*7) + 32 bytes
via subq to store some local values (like 4U below). So to unwind, look
at the offset 88-sizeof(long) = 0x50 from here:
Here ^^^^^^^^^^^^^^^^ is the correct ret addr from
__schedule(). It translates to schedule+0x42 (insn after a call to
__schedule()).
BUT, unwind_next_frame() tries to take the address starting from
0xffff94b50001fdc8. That is exactly from thread.sp+88-sizeof(long) =
0xffff94b50001fdc8+88-8 = 0xffff94b50001fe18, which is garbage marked as
NOTE above. So this quits the unwinding as 7793fab6956b2d00 is obviously
not a kernel address.
There was a fix to skip 'struct inactive_task_frame' in
unwind_get_return_address_ptr in the following commit:
187b96db5ca7 ("x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks")
But we need to skip the struct already in the unwinder proper. So
subtract the size (increase the stack pointer) of the structure in
__unwind_start() directly. This allows for removal of the code added by
commit 187b96db5ca7 completely, as the address is now at
'(unsigned long *)state->sp - 1', the same as in the generic case.
[ mingo: Cleaned up the changelog a bit, for better readability. ]
Currently, trying to rename or link a regular file, directory, or
symlink into an encrypted directory fails with EPERM when the source
file is unencrypted or is encrypted with a different encryption policy,
and is on the same mountpoint. It is correct for the operation to fail,
but the choice of EPERM breaks tools like 'mv' that know to copy rather
than rename if they see EXDEV, but don't know what to do with EPERM.
Our original motivation for EPERM was to encourage users to securely
handle their data. Encrypting files by "moving" them into an encrypted
directory can be insecure because the unencrypted data may remain in
free space on disk, where it can later be recovered by an attacker.
It's much better to encrypt the data from the start, or at least try to
securely delete the source data e.g. using the 'shred' program.
However, the current behavior hasn't been effective at achieving its
goal because users tend to be confused, hack around it, and complain;
see e.g. https://github.com/google/fscrypt/issues/76. And in some cases
it's actually inconsistent or unnecessary. For example, 'mv'-ing files
between differently encrypted directories doesn't work even in cases
where it can be secure, such as when in userspace the same passphrase
protects both directories. Yet, you *can* already 'mv' unencrypted
files into an encrypted directory if the source files are on a different
mountpoint, even though doing so is often insecure.
There are probably better ways to teach users to securely handle their
files. For example, the 'fscrypt' userspace tool could provide a
command that migrates unencrypted files into an encrypted directory,
acting like 'shred' on the source files and providing appropriate
warnings depending on the type of the source filesystem and disk.
Receiving errors on unimportant files might also force some users to
disable encryption, thus making the behavior counterproductive. It's
desirable to make encryption as unobtrusive as possible.
Therefore, change the error code from EPERM to EXDEV so that tools
looking for EXDEV will fall back to a copy.
This, of course, doesn't prevent users from still doing the right things
to securely manage their files. Note that this also matches the
behavior when a file is renamed between two project quota hierarchies;
so there's precedent for using EXDEV for things other than mountpoints.
xfstests generic/398 will require an update with this change.
[Rewritten from an earlier patch series by Michael Halcrow.]
Cc: Michael Halcrow <mhalcrow@google.com> Cc: Joe Richey <joerichey@google.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 9495b7e92f716ab2 ("driver core: platform: Initialize
dma_parms for platform devices"), the R-Car SATA device didn't have DMA
parameters. Hence the DMA boundary mask supplied by its driver was
silently ignored, as __scsi_init_queue() doesn't check the return value
of dma_set_seg_boundary(), and the default value of 0xffffffff was used.
Now the device has gained DMA parameters, the driver-supplied value is
used, and the following warning is printed on Salvator-XS:
DMA-API: sata_rcar ee300000.sata: mapping sg segment across boundary [start=0x00000000ffffe000] [end=0x00000000ffffefff] [boundary=0x000000001ffffffe]
WARNING: CPU: 5 PID: 38 at kernel/dma/debug.c:1233 debug_dma_map_sg+0x298/0x300
(the range of start/end values depend on whether IOMMU support is
enabled or not)
The issue here is that SATA_RCAR_DMA_BOUNDARY doesn't have bit 0 set, so
any typical end value, which is odd, will trigger the check.
Fix this by increasing the DMA boundary value by 1.
This also fixes the following WRITE DMA EXT timeout issue:
In p54p_tx(), skb->data is mapped to streaming DMA on line 337:
mapping = pci_map_single(..., skb->data, ...);
Then skb->data is accessed on line 349:
desc->device_addr = ((struct p54_hdr *)skb->data)->req_id;
This access may cause data inconsistency between CPU cache and hardware.
To fix this problem, ((struct p54_hdr *)skb->data)->req_id is stored in
a local variable before DMA mapping, and then the driver accesses this
local variable instead of skb->data.
Cc: <stable@vger.kernel.org> Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200802132949.26788-1-baijiaju@tsinghua.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephane Eranian found a bug in that IBS' current Fetch counter was not
being reset when the driver would write the new value to clear it along
with the enable bit set, and found that adding an MSR write that would
first disable IBS Fetch would make IBS Fetch reset its current count.
Indeed, the PPR for AMD Family 17h Model 31h B0 55803 Rev 0.54 - Sep 12,
2019 states "The periodic fetch counter is set to IbsFetchCnt [...] when
IbsFetchEn is changed from 0 to 1."
Explicitly set IbsFetchEn to 0 and then to 1 when re-enabling IBS Fetch,
so the driver properly resets the internal counter to 0 and IBS
Fetch starts counting again.
A family 15h machine tested does not have this problem, and the extra
wrmsr is also not needed on Family 19h, so only do the extra wrmsr on
families 16h through 18h.
Commit ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
replaced skb_unshare() with skb_copy() to not reduce the data reference
counter of the original skb intentionally. This is not the correct
way to handle the cloned skb because it causes memory leak in 2
following cases:
1/ Sending multicast messages via broadcast link
The original skb list is cloned to the local skb list for local
destination. After that, the data reference counter of each skb
in the original list has the value of 2. This causes each skb not
to be freed after receiving ACK:
tipc_link_advance_transmq()
{
...
/* release skb */
__skb_unlink(skb, &l->transmq);
kfree_skb(skb); <-- memory exists after being freed
}
2/ Sending multicast messages via replicast link
Similar to the above case, each skb cannot be freed after purging
the skb list:
tipc_mcast_xmit()
{
...
__skb_queue_purge(pkts); <-- memory exists after being freed
}
This commit fixes this issue by using skb_unshare() instead. Besides,
to avoid use-after-free error reported by KASAN, the pointer to the
fragment is set to NULL before calling skb_unshare() to make sure that
the original skb is not freed after freeing the fragment 2 times in
case skb_unshare() returns NULL.
Fixes: ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()") Acked-by: Jon Maloy <jmaloy@redhat.com> Reported-by: Thang Hoang Ngo <thang.h.ngo@dektech.com.au> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://lore.kernel.org/r/20201027032403.1823-1-tung.q.nguyen@dektech.com.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Reported-by: Julia Lawall <julia.lawall@inria.fr> Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch efivarfs_alloc_dentry creates dentries with slashes in
their name if the respective EFI variable has slashes in its name. This in
turn causes EIO on getdents64, which prevents a complete directory listing
of /sys/firmware/efi/efivars/.
This patch replaces the invalid shlashes with exclamation marks like
kobject_set_name_vargs does for /sys/firmware/efi/vars/ to have consistently
named dentries under /sys/firmware/efi/vars/ and /sys/firmware/efi/efivars/.
Signed-off-by: Michael Schaller <misch@google.com> Link: https://lore.kernel.org/r/20200925074502.150448-1-misch@google.com Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_EXPERT=y, CONFIG_KASAN=y, CONFIG_RANDOMIZE_BASE=n,
CONFIG_RELOCATABLE=n, we observe the following failure when trying to
link the kernel image with LD=ld.lld:
error: section: .exit.data is not contiguous with other relro sections
ld.lld defaults to -z relro while ld.bfd defaults to -z norelro. This
was previously fixed, but only for CONFIG_RELOCATABLE=y.
Fixes: 3bbd3db86470 ("arm64: relocatable: fix inconsistencies in linker script and options") Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201016175339.2429280-1-ndesaulniers@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building for an embedded target using Yocto, we're sometimes
observing that the version string that gets built into vmlinux (and
thus what uname -a reports) differs from the path under /lib/modules/
where modules get installed in the rootfs, but only in the length of
the -gabc123def suffix. Hence modprobe always fails.
The problem is that Yocto has the concept of "sstate" (shared state),
which allows different developers/buildbots/etc. to share build
artifacts, based on a hash of all the metadata that went into building
that artifact - and that metadata includes all dependencies (e.g. the
compiler used etc.). That normally works quite well; usually a clean
build (without using any sstate cache) done by one developer ends up
being binary identical to a build done on another host. However, one
thing that can cause two developers to end up with different builds
[and thus make one's vmlinux package incompatible with the other's
kernel-dev package], which is not captured by the metadata hashing, is
this `git describe`: The output of that can be affected by
(1) git version: before 2.11 git defaulted to a minimum of 7, since
2.11 (git.git commit e6c587) the default is dynamic based on the
number of objects in the repo
(2) hence even if both run the same git version, the output can differ
based on how many remotes are being tracked (or just lots of local
development branches or plain old garbage)
(3) and of course somebody could have a core.abbrev config setting in
~/.gitconfig
So in order to avoid `uname -a` output relying on such random details
of the build environment which are rather hard to ensure are
consistent between developers and buildbots, make sure the abbreviated
sha1 always consists of exactly 12 hex characters. That is consistent
with the current rule for -stable patches, and is almost always enough
to identify the head commit unambigously - in the few cases where it
does not, the v5.4.3-00021- prefix would certainly nail it down.
[Adapt to `` vs $() differences between 5.4 and upstream.] Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 8034f715f ("powernv/opal-dump: Convert to irq domain")
Converts all the return explicit number to a more proper IRQ_HANDLED,
which looks proper incase of interrupt handler returning case.
Here, It also removes error message like "nobody cared" which was
getting unveiled while returning -1 or 0 from handler.
Currently, enabling f_ncm at SuperSpeed Plus speeds results in an
oops in config_ep_by_speed because ncm_set_alt passes in NULL
ssp_descriptors. Fix this by re-using the SuperSpeed descriptors.
This is safe because usb_assign_descriptors calls
usb_copy_descriptors.
Tested: enabled f_ncm on a dwc3 gadget and 10Gbps link, ran iperf Reviewed-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
usbcore: registered new interface driver etas_es58x
usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: ES581.4
usb 1-1.1: Manufacturer: ETAS GmbH
usb 1-1.1: SerialNumber: 2204355
cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device
Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c
N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.
`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):
Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0159
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES581.4
iSerial 3 2204355
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0035
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 5 Bus Powered Configuration
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 4 ACM Control Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 0
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 10
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0168
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES582
iSerial 3 0108933
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0169
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES584.1
iSerial 3 0100320
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from
ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync()
and ufshcd_hold() will cause a race condition. Fix this by removing the
unnecessary calls of pm_runtime_get_sync() and ufshcd_hold().
Link: https://lore.kernel.org/r/1596975355-39813-3-git-send-email-cang@codeaurora.org Reviewed-by: Hongwu Su <hongwus@codeaurora.org> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit 6ec4147e7bdb ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
When a usrjquota or grpjquota mount option is used multiple times, we
will leak memory allocated for the file name. Make sure the last setting
is used and all the previous ones are properly freed.
Reported-by: syzbot+c9e294bbe0333a6b7640@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
While aborting the I/O, the firmware cleanup task timed out and driver
deleted the I/O from active command list. Some time later the firmware
sent the cleanup task response and driver again deleted the I/O from
active command list causing firmware to send completion for non-existent
I/O and list_del corruption of active command list.
Add fix to check if I/O is present before deleting it from the active
command list to ensure firmware sends valid I/O completion and protect
against list_del corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-4-mrangankar@marvell.com Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Since l2cap_sock_teardown_cb doesn't acquire the channel lock before
setting the socket as zapped, it could potentially race with
l2cap_sock_release which frees the socket. Thus, wait until the cleanup
is complete before marking the socket as zapped.
This race was reproduced on a JBL GO speaker after the remote device
rejected L2CAP connection due to resource unavailability.
Here is a dmesg log with debug logs from a repro of this bug:
[ 3465.424086] Bluetooth: hci_core.c:hci_acldata_packet() hci0 len 16 handle 0x0003 flags 0x0002
[ 3465.424090] Bluetooth: hci_conn.c:hci_conn_enter_active_mode() hcon 00000000cfedd07d mode 0
[ 3465.424094] Bluetooth: l2cap_core.c:l2cap_recv_acldata() conn 000000007eae8952 len 16 flags 0x2
[ 3465.424098] Bluetooth: l2cap_core.c:l2cap_recv_frame() len 12, cid 0x0001
[ 3465.424102] Bluetooth: l2cap_core.c:l2cap_raw_recv() conn 000000007eae8952
[ 3465.424175] Bluetooth: l2cap_core.c:l2cap_sig_channel() code 0x03 len 8 id 0x0c
[ 3465.424180] Bluetooth: l2cap_core.c:l2cap_connect_create_rsp() dcid 0x0045 scid 0x0000 result 0x02 status 0x00
[ 3465.424189] Bluetooth: l2cap_core.c:l2cap_chan_put() chan 000000006acf9bff orig refcnt 4
[ 3465.424196] Bluetooth: l2cap_core.c:l2cap_chan_del() chan 000000006acf9bff, conn 000000007eae8952, err 111, state BT_CONNECT
[ 3465.424203] Bluetooth: l2cap_sock.c:l2cap_sock_teardown_cb() chan 000000006acf9bff state BT_CONNECT
[ 3465.424221] Bluetooth: l2cap_core.c:l2cap_chan_put() chan 000000006acf9bff orig refcnt 3
[ 3465.424226] Bluetooth: hci_core.h:hci_conn_drop() hcon 00000000cfedd07d orig refcnt 6
[ 3465.424234] BUG: spinlock bad magic on CPU#2, kworker/u17:0/159
[ 3465.425626] Bluetooth: hci_sock.c:hci_sock_sendmsg() sock 000000002bb0cb64 sk 00000000a7964053
[ 3465.430330] lock: 0xffffff804410aac0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 3465.430332] Causing a watchdog bite!
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's an overflow bug in the realtime allocator. If the rt volume is
large enough to handle a single allocation request that is larger than
the maximum bmap extent length and the rt bitmap ends exactly on a
bitmap block boundary, it's possible that the near allocator will try to
check the freeness of a range that extends past the end of the bitmap.
This fails with a corruption error and shuts down the fs.
Therefore, constrain maxlen so that the range scan cannot run off the
end of the rt bitmap.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
unlock_new_inode() is only meant to be called after a new inode has
already been inserted into the hash table. But reiserfs_new_inode() can
call it even before it has inserted the inode, triggering the WARNING in
unlock_new_inode(). Fix this by only calling unlock_new_inode() if the
inode has the I_NEW flag set, indicating that it's in the table.
This addresses the syzbot report "WARNING in unlock_new_inode"
(https://syzkaller.appspot.com/bug?extid=187510916eb6a14598f7).
Link: https://lore.kernel.org/r/20200628070057.820213-1-ebiggers@kernel.org Reported-by: syzbot+187510916eb6a14598f7@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calls to usb_kill_anchored_urbs() after usb_kill_urb() on multiprocessor
systems create a race condition in which usb_kill_anchored_urbs() deallocates
the URB before the completer callback is called in usb_kill_urb(), resulting
in a use-after-free.
To fix this, add proper lock protection to usb_kill_urb() calls that can
possibly run concurrently with usb_kill_anchored_urbs().
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com> Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we fail to read inode, some data accessed in udf_evict_inode() may
be uninitialized. Move the accesses to !is_bad_inode() branch.
Reported-by: syzbot+91f02b28f9bb5f5f1341@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Although UDF standard allows it, we don't support sparing table larger
than a single block. Check it during mount so that we don't try to
access memory beyond end of buffer.
Reported-by: syzbot+9991561e714f597095da@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
BUG: KASAN: use-after-free in __lock_acquire+0x3fd4/0x4180
kernel/locking/lockdep.c:3831
Read of size 8 at addr ffff8880683b0018 by task syz-executor.0/3377
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 0000000000390000EE0100000000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 000000000000000000000039C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
trace-cmd report doesn't show events from target subsystem because
scsi_command_size() leaks through event format string:
[target:target_sequencer_start] function scsi_command_size not defined
[target:target_cmd_complete] function scsi_command_size not defined
Addition of scsi_command_size() to plugin_scsi.c in trace-cmd doesn't
help because an expression is used inside TP_printk(). trace-cmd event
parser doesn't understand minus sign inside [ ]:
Error: expected ']' but read '-'
Rather than duplicating kernel code in plugin_scsi.c, provide a dedicated
field for CONTROL byte.
Link: https://lore.kernel.org/r/20200929125957.83069-1-r.bolshakov@yadro.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
get_gendisk grabs a reference on the disk and file operation, so this
code will leak both of them while having absolutely no use for the
gendisk itself.
This effectively reverts commit 2df83fa4bce421f ("PM / Hibernate: Use
get_gendisk to verify partition if resume_file is integer format")
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Number of bytes allocated for mft record should be equal to the mft record
size stored in ntfs superblock as reported by syzbot, userspace might
trigger out-of-bounds read by dereferencing ctx->attr in ntfs_attr_find()
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For other error
paths after this call, things are the same.
Fix this by adding pm_runtime_put_noidle() after 'err_runtime_disable'
label. But in this case, the error path after pm_runtime_put_sync()
will decrease PM usage counter twice. Thus add an extra
pm_runtime_get_noresume() in this path to balance PM counter.
The patch just remembers the "nodes" entry pointer in space as I think
it's created as subdirectory when parent "spaces" is created. In
function drop_space() we will lost the pointer reference to nds because
configfs_remove_default_groups(). However as this subdirectory is always
available when "spaces" exists it will just be freed when "spaces" will be
freed.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log