Konrad Dybcio [Tue, 4 Mar 2025 17:10:46 +0000 (18:10 +0100)]
arm64: dts: qcom: x1e80100-romulus: Keep L12B and L15B always on
These regulators power some electronic components onboard. They're
most likely kept online by other pieces of firmware, but you can never
be sure enough.
Fixes: 09d77be56093 ("arm64: dts: qcom: Add support for X1-based Surface Laptop 7 devices") Reported-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20250304-topic-sl7_vregs_aon-v1-1-b2dc706e4157@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the WiFi/BT nodes for QCP and describe the regulators for the WCN7850
combo chip using the new power sequencing bindings. All voltages are
derived from chained fixed regulators controlled using a single GPIO.
The same setup also works for CRD (and likely most of the other X1E80100
laptops). However, unlike the QCP they use soldered or removable M.2 cards
supplied by a single 3.3V fixed regulator. The other necessary voltages are
then derived inside the M.2 card. Describing this properly requires
new bindings, so this commit only adds QCP for now.
Krzysztof Kozlowski [Wed, 19 Feb 2025 09:07:51 +0000 (10:07 +0100)]
arm64: dts: qcom: Correct white-space style
There should be exactly one space before and after '=', and one space
before '{'. No functional impact. Verified with comparing decompiled
DTB (dtx_diff and fdtdump+diff).
Lijuan Gao [Fri, 21 Feb 2025 07:39:57 +0000 (15:39 +0800)]
arm64: dts: qcom: qcs615: Add Command DB support
Command DB is a database in the shared memory of QCOM SoCs, that
provides a mapping between resource key and the resource address for a
system resource managed by a remote processor. The data is stored in a
shared memory region and is loaded by the remote processor. Therefore,
enabling Command DB ensures that those resources function properly.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:10 +0000 (10:59 +0100)]
arm64: dts: qcom: sm8250-elish: Switch to undeprecated qcom,calibration-variant
The property qcom,ath11k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:09 +0000 (10:59 +0100)]
arm64: dts: qcom: sc8280xp: Switch to undeprecated qcom,calibration-variant
The property qcom,ath11k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:08 +0000 (10:59 +0100)]
arm64: dts: qcom: sa8775p-ride: Switch to undeprecated qcom,calibration-variant
The property qcom,ath11k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:07 +0000 (10:59 +0100)]
arm64: dts: qcom: qcm6490: Switch to undeprecated qcom,calibration-variant
The property qcom,ath11k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:06 +0000 (10:59 +0100)]
arm64: dts: qcom: sm8150-hdk: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:05 +0000 (10:59 +0100)]
arm64: dts: qcom: sm6115: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:04 +0000 (10:59 +0100)]
arm64: dts: qcom: sda660-ifc6560: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:03 +0000 (10:59 +0100)]
arm64: dts: qcom: sdm845: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:02 +0000 (10:59 +0100)]
arm64: dts: qcom: sc7180: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:01 +0000 (10:59 +0100)]
arm64: dts: qcom: qrb4210-rb2: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:59:00 +0000 (10:59 +0100)]
arm64: dts: qcom: qrb2210-rb1: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Krzysztof Kozlowski [Tue, 25 Feb 2025 09:58:59 +0000 (10:58 +0100)]
arm64: dts: qcom: msm8998: Switch to undeprecated qcom,calibration-variant
The property qcom,ath10k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Aleksandrs Vinarskis [Wed, 26 Feb 2025 23:12:12 +0000 (00:12 +0100)]
arm64: dts: qcom: x1e80100-qcp: Enable HBR3 on external DPs
When no link frequencies are set, msm/dp driver defaults to HBR2 speed.
Explicitly list supported frequencies including HBR3/8.1Gbps for all
external DisplayPort(s).
Aleksandrs Vinarskis [Wed, 26 Feb 2025 23:12:11 +0000 (00:12 +0100)]
arm64: dts: qcom: x1e80100-hp-x14: Enable HBR3 on external DPs
When no link frequencies are set, msm/dp driver defaults to HBR2 speed.
Explicitly list supported frequencies including HBR3/8.1Gbps for all
external DisplayPort(s).
Aleksandrs Vinarskis [Wed, 26 Feb 2025 23:12:10 +0000 (00:12 +0100)]
arm64: dts: qcom: x1e001de-devkit: Enable HBR3 on external DPs
When no link frequencies are set, msm/dp driver defaults to HBR2 speed.
Explicitly list supported frequencies including HBR3/8.1Gbps for all
external DisplayPort(s).
Aleksandrs Vinarskis [Wed, 26 Feb 2025 23:12:09 +0000 (00:12 +0100)]
arm64: dts: qcom: x1e80100-dell-xps13-9345: Enable external DP support
Particular laptops comes with two USB Type-C ports, both supporting DP
alt mode. Enable output on both of them. Explicitly list supported
frequencies including HBR3/8.1Gbps for all external DisplayPort(s).
Due to support missing in the USB/DisplayPort combo PHY driver,
the external DisplayPort is limited to 2 lanes.
Derived from:
arm64: dts: qcom: x1e80100-t14s: Add external DP support
Nikita Travkin [Thu, 27 Feb 2025 14:26:49 +0000 (19:26 +0500)]
arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Drop CMA heap
Initially added, the cma heap was supposed to help with libcamera swisp,
however a mistake was made such that the node was never applied as part
of the overlay since the change was added to the overlay root ("/") and
not with a reference to the target dtb root ("&{/}"). Moveover libcamera
doesn't require CMA heap on Qualcomm platforms anymore as it can now use
UDMA buffers instead.
Drop the CMA heap node. This change has no effect on the final dtb.
Nikita Travkin [Thu, 27 Feb 2025 14:26:48 +0000 (19:26 +0500)]
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Drop CMA heap
Initially added, the cma heap was supposed to help with libcamera swisp,
however a mistake was made such that the node was never applied as part
of the overlay since the change was added to the overlay root ("/") and
not with a reference to the target dtb root ("&{/}"). Moveover libcamera
doesn't require CMA heap on Qualcomm platforms anymore as it can now use
UDMA buffers instead.
Drop the CMA heap node. This change has no effect on the final dtb.
Stephan Gerhold [Wed, 19 Feb 2025 11:36:21 +0000 (12:36 +0100)]
arm64: dts: qcom: x1e80100: Drop unused passive thermal trip points for CPU
There are currently two passive trip points defined for the CPU, but no
cooling devices are attached to the thermal zones. We don't have support
for cpufreq upstream yet, but actually this is redundant anyway because the
CPU is throttled automatically when reaching high temperatures.
Drop the passive trip points and keep just the critical shutdown as safety
measure in case the throttling fails.
Stephan Gerhold [Wed, 19 Feb 2025 11:36:20 +0000 (12:36 +0100)]
arm64: dts: qcom: x1e80100: Add GPU cooling
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.
Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.
Cc: stable@vger.kernel.org Fixes: 721e38301b79 ("arm64: dts: qcom: x1e80100: Add gpu support") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-3-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stephan Gerhold [Wed, 19 Feb 2025 11:36:18 +0000 (12:36 +0100)]
arm64: dts: qcom: x1e80100: Fix video thermal zone
A passive trip point at 125°C is pretty high, this is usually the
temperature for the critical shutdown trip point. Also, we don't have any
passive cooling devices attached to the video thermal zone.
Change this to be a critical trip point, and add a "hot" trip point at
90°C for consistency with the other thermal zones.
Cc: stable@vger.kernel.org Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-1-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Neil Armstrong [Thu, 27 Feb 2025 09:00:33 +0000 (10:00 +0100)]
arm64: dts: qcom: sm8650: add missing cpu-cfg interconnect path in the mdss node
The bindings requires the mdp0-mem and the cpu-cfg interconnect path,
add the missing cpu-cfg path to fix the dtbs check error and also to ensure
that MDSS has enough bandwidth to let HLOS write config registers.
Neil Armstrong [Thu, 27 Feb 2025 09:00:32 +0000 (10:00 +0100)]
arm64: dts: qcom: sm8550: add missing cpu-cfg interconnect path in the mdss node
The bindings requires the mdp0-mem and the cpu-cfg interconnect path,
add the missing cpu-cfg path to fix the dtbs check error and also to ensure
that MDSS has enough bandwidth to let HLOS write config registers.
Partially revert commit a86d84409947 ("arm64: dts: qcom: qcs8300: add
QCrypto nodes") by dropping the untested QCE device node. Devicetree
bindings test failures were reported on mailing list on 16th of January
and after two weeks still no fixes:
qcs8300-ride.dtb: crypto@1dfa000: compatible: 'oneOf' conditional failed, one must be fixed:
...
'qcom,qcs8300-qce' is not one of ['qcom,ipq4019-qce', 'qcom,sm8150-qce']
Reported-by: Rob Herring <robh@kernel.org> Closes: https://lore.kernel.org/all/CAL_JsqL0HzzGXnCD+z4GASeXNsBxrdw8-qyfHj8S+C2ucK6EPQ@mail.gmail.com/ Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250128115333.95021-2-krzysztof.kozlowski@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Partially revert commit 7ff3da43ef44 ("arm64: dts: qcom: sa8775p: add
QCrypto nodes") by dropping the untested QCE device node. Devicetree
bindings test failures were reported on mailing list on 16th of January
and after two weeks still no fixes:
sa8775p-ride.dtb: crypto@1dfa000: compatible: 'oneOf' conditional failed, one must be fixed:
...
'qcom,sa8775p-qce' is not one of ['qcom,ipq4019-qce', 'qcom,sm8150-qce']
Reported-by: Rob Herring <robh@kernel.org> Closes: https://lore.kernel.org/all/CAL_JsqJG_w9jyWjVR=QnPuJganG4uj9+9cEXZ__UAiCw2ZYZZA@mail.gmail.com/ Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250128115333.95021-1-krzysztof.kozlowski@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Neil Armstrong [Wed, 15 Jan 2025 13:44:01 +0000 (14:44 +0100)]
arm64: dts: qcom: sm8650: add QUP serial engines OPP tables
The QUP Serial Engines requires different power domain level
depending on their working frequency, add the required OPP
table with the level associated with all possible frequencies.
For the "I2C Hub" serial engines, sinse they only support a
single Operating Point, only add a single power domain level
property.
Neil Armstrong [Wed, 15 Jan 2025 13:44:00 +0000 (14:44 +0100)]
arm64: dts: qcom: sm8650: add OPP table support to PCIe
The PCIe bus interconnect path can be scaled depending on the
PCIe link established, add the OPP table with all the possible
link speeds and the associated power domain level.
Neil Armstrong [Wed, 15 Jan 2025 13:43:58 +0000 (14:43 +0100)]
arm64: dts: qcom: sm8650: set CPU interconnect paths as ACTIVE_ONLY
In all interconnect paths involving the cpu (MASTER_APPSS_PROC), use
the QCOM_ICC_TAG_ACTIVE_ONLY which will only retain the vote if
the CPU is online, leaving the firmware disabling the path when the
CPUs goes in suspend-idle.
Neil Armstrong [Wed, 15 Jan 2025 13:43:56 +0000 (14:43 +0100)]
arm64: dts: qcom: sm8550: add QUP serial engines OPP tables
The QUP Serial Engines requires different power domain level
depending on their working frequency, add the required OPP
table with the level associated with all possible frequencies.
For the "I2C Hub" serial engines, sinse they only support a
single Operating Point, only add a single power domain level
property.
Neil Armstrong [Wed, 15 Jan 2025 13:43:55 +0000 (14:43 +0100)]
arm64: dts: qcom: sm8550: add OPP table support to PCIe
The PCIe bus interconnect path can be scaled depending on the
PCIe link established, add the OPP table with all the possible
link speeds and the associated power domain level.
Neil Armstrong [Wed, 15 Jan 2025 13:43:54 +0000 (14:43 +0100)]
arm64: dts: qcom: sm8550: set CPU interconnect paths as ACTIVE_ONLY
In all interconnect paths involving the cpu (MASTER_APPSS_PROC), use
the QCOM_ICC_TAG_ACTIVE_ONLY which will only retain the vote if
the CPU is online, leaving the firmware disabling the path when the
CPUs goes in suspend-idle.
Two regulators (GPIO 72 & 107) for the IMX766 sensor are missing here.
Without a driver, it's unclear if they're extra supplies or pwdn/power
GPIOs (labeled "custom" in the downstream kernel).
So add only those fixed regulators that are currently predictable for
camera sensors, camera EEPROMs and camera actuators.
Neil Armstrong [Mon, 3 Feb 2025 13:23:19 +0000 (14:23 +0100)]
arm64: dts: qcom: sm8650: harmonize all unregulated thermal trip points
While the CPUs thermal is handled by the LMH, and GPU has a passive
cooldowm via the HLOS DCVS, all the other thermal blocks only have
hot and critical and no passive/active trip points.
Passive or active thermal management for those blocks should
be either defined if somehow we can express those in DT or
in the board definition if there's an active cooling device
available.
The tsens MAX_THRESHOLD is set to 120C on those platforms, so set
the hot to 110C to leave a chance to HLOS to react and critical to
115C to avoid the monitor thermal shutdown.
In the case a passive or active cooling device would be
available, the downstream reference implementation uses
the 95C "tj" trip point, as we already use for the
gpuss thermal blocks.
Neil Armstrong [Mon, 3 Feb 2025 13:23:18 +0000 (14:23 +0100)]
arm64: dts: qcom: sm8650: setup gpu thermal with higher temperatures
On the SM8650, the dynamic clock and voltage scaling (DCVS) for the GPU
is done from the HLOS, but the GPU can achieve a much higher temperature
before failing according the reference downstream implementation.
Set higher temperatures in the GPU trip points corresponding to
the temperatures provided by Qualcomm in the dowstream source, much
closer to the junction temperature and with a higher critical
temperature trip in the case the HLOS DCVS cannot handle the
temperature surge.
The tsens MAX_THRESHOLD is set to 120C on those platforms, so set
the hot to 110C to leave a chance to HLOS to react and critical to
115C to avoid the monitor thermal shutdown.
Neil Armstrong [Mon, 3 Feb 2025 13:23:17 +0000 (14:23 +0100)]
arm64: dts: qcom: sm8650: drop cpu thermal passive trip points
On the SM8650, the dynamic clock and voltage scaling (DCVS) is done in an
hardware controlled loop using the LMH and EPSS blocks with constraints and
OPPs programmed in the board firmware.
Since the Hardware does a better job at maintaining the CPUs temperature
in an acceptable range by taking in account more parameters like the die
characteristics or other factory fused values, it makes no sense to try
and reproduce a similar set of constraints with the Linux cpufreq thermal
core.
In addition, the tsens IP is responsible for monitoring the temperature
across the SoC and the current settings will heavily trigger the tsens
UP/LOW interrupts if the CPU temperatures reaches the hardware thermal
constraints which are currently defined in the DT. And since the CPUs
are not hooked in the thermal trip points, the potential interrupts and
calculations are a waste of system resources.
Drop the current passive trip points and only leave the critical trip
point that will trigger a software system reboot before an hardware
thermal shutdown in the allmost impossible case the hardware DCVS cannot
handle the temperature surge.
Konrad Dybcio [Mon, 3 Feb 2025 14:43:25 +0000 (15:43 +0100)]
arm64: dts: qcom: Add X1P42100 SoC and CRD
The X1 family is split into two parts: the 10- and 12-core parts are
variants of the same silicon with different fusing, whereas the 8-core
ones are a separate design. Thankfully, the software interface is only
barely different, letting us reuse much of the existing X1 work.
Introduce support for the X1P42100 SoC and the CRD based on it, through
overlaying some bits. Everything we already support on X1E80100 and
friends, minus the GPU, should work as-is.
Konrad Dybcio [Mon, 3 Feb 2025 14:43:23 +0000 (15:43 +0100)]
arm64: dts: qcom: x1e80100: Wire up PCIe PHY NOCSR resets
Asserting the NOCSR reset line keeps the PHY registers in tact.
This allows us to avoid programming long tables of magic values in the
operating system.
Wire up these resets to PCIe PHY4 and 5 (it's there on the others).
Chukun Pan [Mon, 10 Feb 2025 07:01:22 +0000 (15:01 +0800)]
arm64: dts: qcom: ipq6018: add LDOA2 regulator
Add LDOA2 regulator from MP5496 to support SDCC voltage scaling.
Suggested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250210070122.208842-6-amadeus@jmu.edu.cn Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Chukun Pan [Mon, 10 Feb 2025 07:01:20 +0000 (15:01 +0800)]
arm64: dts: qcom: ipq6018: move mp5496 regulator out of soc dtsi
Some IPQ60xx SoCs don't come with the mp5496 pmic chip. The mp5496
pmic was never part of the IPQ60xx SoC, it's optional, so we moved
it out of the soc dtsi.
Chukun Pan [Mon, 10 Feb 2025 07:01:19 +0000 (15:01 +0800)]
arm64: dts: qcom: ipq6018: add 1.5GHz CPU Frequency
The early version of IPQ6000 (SoC id: IPQ6018, SBL version:
BOOT.XF.0.3-00077-IPQ60xxLZB-2) and IPQ6005 SoCs can reach
a max frequency of 1.5GHz, so add this CPU frequency.
Chukun Pan [Mon, 10 Feb 2025 07:01:18 +0000 (15:01 +0800)]
arm64: dts: qcom: ipq6018: add 1.2GHz CPU Frequency
The final version of IPQ6000 (SoC id: IPQ6000, SBL version:
BOOT.XF.0.3-00086-IPQ60xxLZB-1) has a max design frequency
of 1.2GHz, so add this CPU frequency.
Cheng Jiang [Fri, 10 Jan 2025 06:39:14 +0000 (14:39 +0800)]
arm64: dts: qcom: sa8775p-ride: Add firmware-name in BT node
The sa8775p-ride platform uses the QCA6698 Bluetooth chip. While the
QCA6698 shares the same IP core as the WCN6855, it has different RF
components and RAM sizes, requiring new firmware files. Use the
firmware-name property to specify the NVM and rampatch firmware to load.
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com> Reviewed-by: Zijun Hu <quic_zijuhu@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250110063914.28001-2-quic_chejiang@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
After looking into this, I found the clocks for spi0 to spi7 are
wrong, we can derive the correct clocks from the regular pattern
between spi8 to spi15, spi16 to spi23. Or we can verify it according
to the hex file of BSRC_QSPI.bin(From windows driver qcspi8280.cab)
Enable PMIC and PMIC peripherals for qcs8300-ride board. The qcs8
300-ride uses 2 pmics(pmm8620au:0,pmm8650au:1) on the board, which
are variants of pmm8654au used on sa8775p/qcs9100 -ride(4x pmics).
arm64: dts: qcom: qcs6490-rb3gen2: add and enable BT node
Add the PMU node for WCN6750 present on the qcs6490-rb3gen2
board and assign its power outputs to the Bluetooth module.
In WCN6750 module sw_ctrl and wifi-enable pins are handled
in the wifi controller firmware. Therefore, it is not required
to have those pins' entries in the PMU node.
Neil Armstrong [Tue, 11 Feb 2025 12:56:39 +0000 (13:56 +0100)]
arm64: dts: qcom: sm8650: add cpu OPP table with DDR, LLCC & L3 bandwidths
Add the OPP tables for each CPU clusters (cpu0-1, cpu2-3-4, cpu5-6 & cpu7)
to permit scaling the Last Level Cache Controller (LLCC), DDR and L3 cache
frequency by aggregating bandwidth requests of all CPU core with referenc
to the current OPP they are configured in by the LMH/EPSS hardware.
The effect is a proper caches & DDR frequency scaling when CPU cores
changes frequency.
The OPP tables were built using the downstream memlat ddr, llcc & l3
tables for each cluster types with the actual EPSS cpufreq LUT tables
from running HDK and QRD devices.
The cpu2 and cpu5 tables are similar but must be kept separate to
take in account that they define OPP for shared CPUs of two different
clusters that can scale separately, thus vote different bandwidths.
Neil Armstrong [Tue, 11 Feb 2025 12:56:38 +0000 (13:56 +0100)]
arm64: dts: qcom: sm8650: add cpu interconnect nodes
Add the interconnect entry for each cpu, with 3 different paths:
- CPU to Last Level Cache Controller (LLCC)
- Last Level Cache Controller (LLCC) to DDR
- L3 Cache from CPU to DDR interface
Rakesh Kota [Wed, 12 Feb 2025 11:33:42 +0000 (17:03 +0530)]
arm64: dts: qcom: qcs6490-rb3gen2: Add vadc and adc-tm channels
Add support for vadc and adc-tm channels which are used for
monitoring thermistors present on the platform.
- Add the necessary includes for qcom,spmi-adc7-pm7325 and
qcom,spmi-adc7-pmk8350.
- Add thermal zones for quiet-thermal, sdm-skin-thermal, and
xo-thermal, and define their polling delays and thermal sensors.
- Configure the pm7325_temp_alarm node to use the pmk8350_vadc
channel for thermal monitoring.
- Configure the pmk8350_adc_tm node to enable its thermal sensors
and define their registers and settings.
- Configure the pmk8350_vadc node to define its channels and settings
Pengyu Luo [Sat, 11 Jan 2025 08:32:08 +0000 (16:32 +0800)]
arm64: dts: qcom: sc8280xp-pmics: Add more temp-alarm devices
There are 4 Qualcomm PMIC Die Temp Alarm Sensor Devices under windows os,
in separate dt files, pm8350c and pmr735a have already support temp alarm,
add the rest 2 devices for sc8280xp-pmic.
Temperature trip points are from dsdt(Temp. in tenths of degrees Kelvin).
Konrad Dybcio [Sat, 11 Jan 2025 16:54:19 +0000 (17:54 +0100)]
arm64: dts: qcom: x1e80100: Set CPU interconnect paths as ACTIVE_ONLY
There is no use wasting power on keeping the links between the CPU and
something else online when the CPUs are online. Change the interconnect
tag for such paths, so that RPMh is requested to automatically
clock-gate those when possible.
Keeping these paths online is also a potential power collapse blocker,
however this commit alone doesn't magically fix all the remaining
TODOs related to suspend.
Linus Torvalds [Sun, 2 Feb 2025 18:49:13 +0000 (10:49 -0800)]
Merge tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Linus Torvalds [Sun, 2 Feb 2025 18:40:27 +0000 (10:40 -0800)]
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Len Brown [Sun, 2 Feb 2025 16:43:02 +0000 (10:43 -0600)]
tools/power turbostat: version 2025.02.02
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Linus Torvalds [Sat, 1 Feb 2025 23:07:56 +0000 (15:07 -0800)]
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Linus Torvalds [Sat, 1 Feb 2025 19:30:41 +0000 (11:30 -0800)]
Merge tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Linus Torvalds [Sat, 1 Feb 2025 18:04:29 +0000 (10:04 -0800)]
Merge tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Linus Torvalds [Sat, 1 Feb 2025 17:49:20 +0000 (09:49 -0800)]
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Linus Torvalds [Sat, 1 Feb 2025 17:15:01 +0000 (09:15 -0800)]
Merge tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
projects / users / jedix / linux-maple.git / log