The svc->key field is not released as it should be if ida_simple_get()
fails so fix that.
Fixes: 9aabb68568b4 ("thunderbolt: Fix to check return value of ida_simple_get") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ID registers are RAZ until they've been allocated a purpose, but
that doesn't mean they should be removed from the KVM_GET_REG_LIST
list. So far we only have one register, SYS_ID_AA64ZFR0_EL1, that
is hidden from userspace when its function, SVE, is not present.
Expose SYS_ID_AA64ZFR0_EL1 to userspace as RAZ when SVE is not
implemented. Removing the userspace visibility checks is enough
to reexpose it, as it will already return zero to userspace when
SVE is not present. The register already behaves as RAZ for the
guest when SVE is not present.
Fixes: 73433762fcae ("KVM: arm64/sve: System register context switch and access support") Reported-by: 张东旭 <xu910121@sina.com> Signed-off-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org#v5.2+ Link: https://lore.kernel.org/r/20201105091022.15373-2-drjones@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a device BTRFS_DEV_REPLACE_DEVID without the device replace
item, then it means the filesystem is inconsistent state. This is either
corruption or a crafted image. Fail the mount as this needs a closer
look what is actually wrong.
As of now if BTRFS_DEV_REPLACE_DEVID is present without the replace
item, in __btrfs_free_extra_devids() we determine that there is an
extra device, and free those extra devices but continue to mount the
device.
However, we were wrong in keeping tack of the rw_devices so the syzbot
testcase failed:
The minimum reserve size was adjusted to take into account the height of
the tree we are merging, however we can have a root with a level == 0.
What we want is root_level + 1 to get the number of nodes we may have to
cow. This fixes the enospc_debug warning pops with btrfs/101.
Nikolay: this fixes failures on btrfs/060 btrfs/062 btrfs/063 and
btrfs/195 That I was seeing, the call trace was:
Reported-by: Nikolay Borisov <nborisov@suse.com> Fixes: 44d354abf33e ("btrfs: relocation: review the call sites which can be interrupted by signal") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The macro MOPT_Q is used to indicates the mount option is related to
quota stuff and is defined to be MOPT_NOSUPPORT when CONFIG_QUOTA is
disabled. Normally the quota options are handled explicitly, so it
didn't matter that the MOPT_STRING flag was missing, even though the
usrjquota and grpjquota mount options take a string argument. It's
important that's present in the !CONFIG_QUOTA case, since without
MOPT_STRING, the mount option matcher will match usrjquota= followed
by an integer, and will otherwise skip the table entry, and so "mount
option not supported" error message is never reported.
[ Fixed up the commit description to better explain why the fix
works. --TYT ]
Fixes: 26092bf52478 ("ext4: use a table-driven handler for mount options") Signed-off-by: Kaixu Xia <kaixuxia@tencent.com> Link: https://lore.kernel.org/r/1603986396-28917-1-git-send-email-kaixuxia@tencent.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EROFS has _only one_ ondisk timestamp (ctime is currently
documented and recorded, we might also record mtime instead
with a new compat feature if needed) for each extended inode
since EROFS isn't mainly for archival purposes so no need to
keep all timestamps on disk especially for Android scenarios
due to security concerns. Also, romfs/cramfs don't have their
own on-disk timestamp, and squashfs only records mtime instead.
Let's also derive access time from ondisk timestamp rather than
leaving it empty, and if mtime/atime for each file are really
needed for specific scenarios as well, we can also use xattrs
to record them then.
VRF devices use an optimized direct path on output if a default qdisc
is involved, calling Netfilter hooks directly. This path, however, does
not consider Netfilter rules completing asynchronously, such as with
NFQUEUE. The Netfilter okfn() is called for asynchronously accepted
packets, but the VRF never passes that packet down the stack to send
it out over the slave device. Using the slower redirect path for this
seems not feasible, as we do not know beforehand if a Netfilter hook
has asynchronously completing rules.
Fix the use of asynchronously completing Netfilter rules in OUTPUT and
POSTROUTING by using a special completion function that additionally
calls dst_output() to pass the packet down the stack. Also, slightly
adjust the use of nf_reset_ct() so that is called in the asynchronous
case, too.
Fixes: dcdd43c41e60 ("net: vrf: performance improvements for IPv4") Fixes: a9ec54d1b0cd ("net: vrf: performance improvements for IPv6") Signed-off-by: Martin Willi <martin@strongswan.org> Link: https://lore.kernel.org/r/20201106073030.3974927-1-martin@strongswan.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If memory allocation for 'kbuf' succeed, cosa_write() doesn't have a
corresponding kfree() in exception handling. Thus add kfree() for this
function implementation.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz> Link: https://lore.kernel.org/r/20201110144614.43194-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit dabf6b36b83a ("of: Add OF_DMA_DEFAULT_COHERENT & select it on
powerpc") added a check to of_dma_is_coherent which returns early
if OF_DMA_DEFAULT_COHERENT is enabled. This results in the of_node_put()
being skipped causing a memory leak. Moved the of_node_get() below this
check so we now we only get the node if OF_DMA_DEFAULT_COHERENT is not
enabled.
We also need to drop the iolock when invalidate_inode_pages2 fails, not
only on all other error or successful cases.
Fixes: 527851124d10 ("xfs: implement pNFS export operations") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the net core, the struct net_device_ops -> ndo_set_rx_mode()
callback is called with the dev->addr_list_lock spinlock held.
However, this driver's ndo_set_rx_mode callback eventually calls
lan743x_dp_write(), which acquires a mutex. Mutex acquisition
may sleep, and this is not allowed when holding a spinlock.
Fix by removing the dp_lock mutex entirely. Its purpose is to
prevent concurrent accesses to the data port. No concurrent
accesses are possible, because the dev->addr_list_lock
spinlock in the core only lets through one thread at a time.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com> Link: https://lore.kernel.org/r/20201109203828.5115-1-TheSven73@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix some serious WTF in the reference count scrubber's rmap fragment
processing. The code comment says that this loop is supposed to move
all fragment records starting at or before bno onto the worklist, but
there's no obvious reason why nr (the number of items added) should
increment starting from 1, and breaking the loop when we've added the
target number seems dubious since we could have more rmap fragments that
should have been added to the worklist.
This seems to manifest in xfs/411 when adding one to the refcount field.
Fixes: dbde19da9637 ("xfs: cross-reference the rmapbt data with the refcountbt") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This provides users the ability to look up a reverse mapping from a bmbt
record -- start with the physical block; then if there are multiple
records for the same block, move on to the owner; then the inode fork
type; and so on to the file offset.
However, the key comparison functions incorrectly remove the
fork/btree/unwritten information that's encoded in the on-disk offset.
This means that lookup comparisons are only done with:
(physical block, owner, offset)
This means that queries can return incorrect results. On consistent
filesystems this hasn't been an issue because blocks are never shared
between forks or with bmbt blocks; and are never unwritten. However,
this bug means that online repair cannot always detect corruption in the
key information in internal rmapbt nodes.
Found by fuzzing keys[1].attrfork = ones on xfs/371.
Fixes: 4b8ed67794fe ("xfs: add rmap btree operations") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the bmbt scrubber is looking up rmap extents, we need to set the
extent flags from the bmbt record fully. This will matter once we fix
the rmap btree comparison functions to check those flags correctly.
Fixes: d852657ccfc0 ("xfs: cross-reference reverse-mapping btree") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Pass the same oldext argument (which contains the existing rmapping's
unwritten state) to xfs_rmap_lookup_le_range at the start of
xfs_rmap_convert_shared. At this point in the code, flags is zero,
which means that we perform lookups using the wrong key.
Fixes: 3f165b334e51 ("xfs: convert unwritten status of reverse mappings for shared files") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zero-fill element values for all other cpus than current, just as
when not using prealloc. This is the only way the bpf program can
ensure known initial values for all cpus ('onallcpus' cannot be
set when coming from the bpf program).
The scenario is: bpf program inserts some elements in a per-cpu
map, then deletes some (or userspace does). When later adding
new elements using bpf_map_update_elem(), the bpf program can
only set the value of the new elements for the current cpu.
When prealloc is enabled, previously deleted elements are re-used.
Without the fix, values for other cpus remain whatever they were
when the re-used entry was previously freed.
A selftest is added to validate correct operation in above
scenario as well as in case of LRU per-cpu map element re-use.
When a rule is duplicated, the refcount of the rule is increased so only
the second deletion of the rule should cause destruction of the FTE.
Currently, the FTE will be destroyed in the first deletion of rule since
the modify_mask will be 0.
Fix it and call to destroy FTE only if all the rules (FTE's children)
have been removed.
Fixes: 718ce4d601db ("net/mlx5: Consolidate update FTE for all removal changes") Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some gpio pin at aspeed soc is input only and the prefix name of these
pin is "GPI" only.
This patch fine-tune the condition of GPIO check from "GPIO" to "GPI"
and it will fix the usage error of banks D and E in the AST2400/AST2500
and banks T and U in the AST2600.
Fixes: 4d3d0e4272d8 ("pinctrl: Add core support for Aspeed SoCs") Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20201030055450.29613-1-billy_tsai@aspeedtech.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3193c0836 ("bpf: Disable GCC -fgcse optimization for
___bpf_prog_run()") introduced a __no_fgcse macro that expands to a
function scope __attribute__((optimize("-fno-gcse"))), to disable a
GCC specific optimization that was causing trouble on x86 builds, and
was not expected to have any positive effect in the first place.
However, as the GCC manual documents, __attribute__((optimize))
is not for production use, and results in all other optimization
options to be forgotten for the function in question. This can
cause all kinds of trouble, but in one particular reported case,
it causes -fno-asynchronous-unwind-tables to be disregarded,
resulting in .eh_frame info to be emitted for the function.
This reverts commit 3193c0836, and instead, it disables the -fgcse
optimization for the entire source file, but only when building for
X86 using GCC with CONFIG_BPF_JIT_ALWAYS_ON disabled. Note that the
original commit states that CONFIG_RETPOLINE=n triggers the issue,
whereas CONFIG_RETPOLINE=y performs better without the optimization,
so it is kept disabled in both cases.
Setting both CONFIG_KPROBES=y and CONFIG_FORTIFY_SOURCE=y on ARM leads
to a panic in memcpy() when injecting a kprobe despite the fixes found
in commit e46daee53bb5 ("ARM: 8806/1: kprobes: Fix false positive with
FORTIFY_SOURCE") and commit 0ac569bf6a79 ("ARM: 8834/1: Fix: kprobes:
optimized kprobes illegal instruction").
arch/arm/include/asm/kprobes.h effectively declares
the target type of the optprobe_template_entry assembly label as a u32
which leads memcpy()'s __builtin_object_size() call to determine that
the pointed-to object is of size four. However, the symbol is used as a handle
for the optimised probe assembly template that is at least 96 bytes in size.
The symbol's use despite its type blows up the memcpy() in ARM's
arch_prepare_optimized_kprobe() with a false-positive fortify_panic() when it
should instead copy the optimised probe template into place:
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf87 ("pinctrl: intel: Add support for hardware debouncer") Reported-by: Jamie McClymont <jamie@kwiius.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When changing to use suspend-to-idle to save power, the PMIC irq can not
wakeup the system due to lack of wakeup capability, which will cause
the sub-irqs (such as power key) of the PMIC can not wake up the system.
Thus we can add the wakeup capability for PMIC irq to solve this issue,
as well as removing the IRQF_NO_SUSPEND flag to allow PMIC irq to be
a wakeup source.
Reported-by: Chunyan Zhang <zhang.lyra@gmail.com> Signed-off-by: Baolin Wang <baolin.wang7@gmail.com> Tested-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend to IDLE invokes tick_unfreeze() on resume. tick_unfreeze() on the
first resuming CPU resumes timekeeping, which also has the side effect of
resetting the softlockup watchdog on this CPU.
But on the secondary CPUs the watchdog is not reset in the resume /
unfreeze() path, which can result in false softlockup warnings on those
CPUs depending on the time spent in suspend.
Prevent this by clearing the softlock watchdog in the unfreeze path also
on the secondary resuming CPUs.
Removing the duplicate gpio chip select level handling in
bcm2835_spi_setup() left the lflags variable uninitialized. Avoid trhe
use of such variable by passing default flags to
gpiochip_request_own_desc().
Fixes: 5e31ba0c0543 ("spi: bcm2835: fix gpio cs level inversion") Signed-off-by: Martin Hundebøll <martin@geanix.com> Link: https://lore.kernel.org/r/20201105090615.620315-1-martin@geanix.com Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a misconfiguration in the bios of the gpio pin used for the
interrupt in the T490s. When interrupts are enabled in the tpm_tis
driver code this results in an interrupt storm. This was initially
reported when we attempted to enable the interrupt code in the tpm_tis
driver, which previously wasn't setting a flag to enable it. Due to
the reports of the interrupt storm that code was reverted and we went back
to polling instead of using interrupts. Now that we know the T490s problem
is a firmware issue, add code to check if the system is a T490s and
disable interrupts if that is the case. This will allow us to enable
interrupts for everyone else. If the user has a fixed bios they can
force the enabling of interrupts with tpm_tis.interrupts=1 on the
kernel command line.
Cc: Peter Huewe <peterhuewe@gmx.de> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
M-Mode Linux is loaded at the start of RAM, not 2MB later. Perhaps this
should be calculated based on PAGE_OFFSET somehow? Even better would be to
deprecate text_offset and instead introduce something absolute.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bypass the IGD initialization when -ENODEV returns,
that should be the case if opregion is not available for IGD
or within discrete graphics device's option ROM,
or host/lpc bridge is not found.
Then use of -ENODEV here means no special device resources found
which needs special care for VFIO, but we still allow other normal
device resource access.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Xiong Zhang <xiong.y.zhang@intel.com> Cc: Hang Yuan <hang.yuan@linux.intel.com> Cc: Stuart Summers <stuart.summers@intel.com> Signed-off-by: Fred Gao <fred.gao@intel.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put will result in
reference leak in vfio_platform_open, so we should fix it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Acked-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to rcu_cpu_starting() in smp_init_secondary() is not early
enough in the CPU-hotplug onlining process, which results in lockdep
splats as follows:
This is avoided by moving the call to rcu_cpu_starting up near the
beginning of the smp_init_secondary() function. Note that the
raw_smp_processor_id() is required in order to avoid calling into
lockdep before RCU has declared the CPU to be watched for readers.
Certain device drivers allocate IO queues on a per-cpu basis.
On AMD EPYC platform, which can support up-to 256 cpu threads,
this can exceed the current MAX_IRQ_PER_TABLE limit of 256,
and result in the error message:
AMD-Vi: Failed to allocate IRTE
This has been observed with certain NVME devices.
AMD IOMMU hardware can actually support upto 512 interrupt
remapping table entries. Therefore, update the driver to
match the hardware limit.
Please note that this also increases the size of interrupt remapping
table to 8KB per device when using the 128-bit IRTE format.
The request may be executed asynchronously, and rq->state may be
changed to IDLE. To avoid repeated request completion, only
MQ_RQ_COMPLETE of rq->state is checked in nvme_tcp_complete_timed_out.
It is not safe, so need adding check IDLE for rq->state.
The request may be executed asynchronously, and rq->state may be
changed to IDLE. To avoid repeated request completion, only
MQ_RQ_COMPLETE of rq->state is checked in nvme_rdma_complete_timed_out.
It is not safe, so need adding check IDLE for rq->state.
Now use teardown_lock to serialize for time out and tear down. This may
cause abnormal: first cancel all request in tear down, then time out may
complete the request again, but the request may already be freed or
restarted.
To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue. At the same time we need to delete
teardown_lock.
Now use teardown_lock to serialize for time out and tear down. This may
cause abnormal: first cancel all request in tear down, then time out may
complete the request again, but the request may already be freed or
restarted.
To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue. At the same time we need to delete
teardown_lock.
While reenabling the IRQ after irq poll there may be small time window
where HBA firmware has posted some replies and raise the interrupts but
driver has not received the interrupts. So we may observe I/O timeouts as
the driver has not processed the replies as interrupts got missed while
reenabling the IRQ.
To fix this issue the driver has to go for one more round of processing the
reply descriptors from reply descriptor post queue after enabling the IRQ.
Link: https://lore.kernel.org/r/20201102072746.27410-1-sreekanth.reddy@broadcom.com Reported-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
alua_bus_detach() might be running concurrently with alua_rtpg_work(), so
we might trip over h->sdev == NULL and call BUG_ON(). The correct way of
handling it is to not set h->sdev to NULL in alua_bus_detach(), and call
rcu_synchronize() before the final delete to ensure that all concurrent
threads have left the critical section. Then we can get rid of the
BUG_ON() and replace it with a simple if condition.
There's a race condition in the netdev registration in that
NETDEV_REGISTER actually happens after the netdev is available,
and so if we initialize things only there, we might get called
with an uninitialized wdev through nl80211 - not using a wdev
but using a netdev interface index.
I found this while looking into a syzbot report, but it doesn't
really seem to be related, and unfortunately there's no repro
for it (yet). I can't (yet) explain how it managed to get into
cfg80211_release_pmsr() from nl80211_netlink_notify() without
the wdev having been initialized, as the latter only iterates
the wdevs that are linked into the rdev, which even without the
change here happened after init.
However, looking at this, it seems fairly clear that the init
needs to be done earlier, otherwise we might even re-init on a
netns move, when data might still be pending.
When ieee80211_skb_resize() is called from ieee80211_build_hdr()
the skb has no 802.11 header yet, in fact it consist only of the
payload as the ethernet frame is removed. As such, we're using
the payload data for ieee80211_is_mgmt(), which is of course
completely wrong. This didn't really hurt us because these are
always data frames, so we could only have added more tailroom
than we needed if we determined it was a management frame and
sdata->crypto_tx_tailroom_needed_cnt was false.
However, syzbot found that of course there need not be any payload,
so we're using at best uninitialized memory for the check.
Fix this to pass explicitly the kind of frame that we have instead
of checking there, by replacing the "bool may_encrypt" argument
with an argument that can carry the three possible states - it's
not going to be encrypted, it's a management frame, or it's a data
frame (and then we check sdata->crypto_tx_tailroom_needed_cnt).
This reverts commit f87812284172a9809820d10143b573d833cd3f75 ("drm/amdgpu:
Fix bug where DPM is not enabled after hibernate and resume").
It was intended to fix Hawaii S4(hibernation) issue but break S3. As
ixFEATURE_STATUS is filled with garbage data on resume which can be
only cleared by reloading smc firmware(but that will involve many
changes). So, we will revert this S4 fix and seek a new way.
Signed-off-by: Evan Quan <evan.quan@amd.com> Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, gfs2_fitrim was not properly checking for a "live" file
system. If the file system had something to trim and the file system
was read-only (or spectator) it would start the trim, but when it starts
the transaction, gfs2_trans_begin returns -EROFS (read-only file system)
and it errors out. However, if the file system was already trimmed so
there's no work to do, it never called gfs2_trans_begin. That code is
bypassed so it never returns the error. Instead, it returns a good
return code with 0 work. All this makes for inconsistent behavior:
The same fstrim command can return -EROFS in one case and 0 in another.
This tripped up xfstests generic/537 which reports the error as:
+fstrim with unrecovered metadata just ate your filesystem
This patch adds a check for a "live" (iow, active journal, iow, RW)
file system, and if not, returns the error properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gfs2 creates an address space for its rgrps called sd_aspace, but it never
called truncate_inode_pages_final on it. This confused vfs greatly which
tried to reference the address space after gfs2 had freed the superblock
that contained it.
This patch adds a call to truncate_inode_pages_final for sd_aspace, thus
avoiding the use-after-free.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function gfs2_clear_rgrpd calls kfree(rgd->rd_bits) before calling
return_all_reservations, but return_all_reservations still dereferences
rgd->rd_bits in __rs_deltree. Fix that by moving the call to kfree below the
call to return_all_reservations.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The broken jack detection should be fixed by commit a6e7d0a4bdb0 ("ALSA:
hda: fix jack detection with Realtek codecs when in D3"), let's try
enabling runtime PM by default again.
Both pm_runtime_force_suspend() and pm_runtime_force_resume() have
some implicit checks, so it can make code flow more straightforward if
we separate runtime and system suspend callbacks.
High Definition Audio Specification, 4.5.9.3 Codec Wake From System S3
states that codec can wake the system up from S3 if WAKEEN is toggled.
Since HDA controller has different wakeup settings for runtime and
system susend, we also need to explicitly disable direct-complete which
can be enabled automatically by PCI core. In addition to that, avoid
waking up codec if runtime resume is for system suspend, to not break
direct-complete for codecs.
While at it, also remove AZX_DCAPS_SUSPEND_SPURIOUS_WAKEUP, as the
original bug commit a6630529aecb ("ALSA: hda: Workaround for spurious
wakeups on some Intel platforms") solves doesn't happen with this
patch.
Drop unneeded <linux/wait.h> header inclusion to fix pidfd compilation
errors seen in Fedora 32:
In file included from pidfd_open_test.c:9:
../../../../usr/include/linux/wait.h:17:16: error: expected identifier before numeric constant
17 | #define P_ALL 0
| ^
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
More recent libc implementations are now using openat/openat2 system
calls so also add do_sys_openat2 to the tracing so that the test
passes on these systems because do_sys_open may not be called.
Thanks to Masami Hiramatsu for the help on getting this fix to work
correctly.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
goku_probe() goes to error label "err" and invokes goku_remove()
in case of failures of pci_enable_device(), pci_resource_start()
and ioremap(). goku_remove() gets a device from
pci_get_drvdata(pdev) and works with it without any checks, in
particular it dereferences a corresponding pointer. But
goku_probe() did not set this device yet. So, one can expect
various crashes. The patch moves setting the device just after
allocation of memory for it.
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Pavel Andrianov <andrianov@ispras.ru> Signed-off-by: Evgeny Novikov <novikov@ispras.ru> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a lot of stuff here which can be done outside of the big
opp_table_lock, do that. This helps avoiding few circular dependency
lockdeps around debugfs and interconnects.
Reported-by: Rob Clark <robdclark@gmail.com> Reported-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A delay must be introduced before the shutdown down of the mclk,
as stated in CS42L51 datasheet. Otherwise the codec may
produce some noise after the end of DAPM power down sequence.
The delay between DAC and CLOCK_SUPPLY widgets is too short.
Add a delay in mclk shutdown request to manage the shutdown delay
explicitly. From experiments, at least 10ms delay is necessary.
Set delay to 20ms as recommended in Documentation/timers/timers-howto.rst
when using msleep().
This is not very UCM friendly both w.r.t to common up configs and
card identification, and UCM2 became totally not usefull with just
one ucm sdm845.conf for two machines which have different setups
w.r.t HDMI and other dais.
Reasons for such thing is partly because Qualcomm machine drivers never
cared to set driver_name.
This patch sets up driver name for the this driver to sort out the
UCM integration issues!
with this its possible to align with what UCM2 expects and we can have
sdm845/DB845.conf
sdm845/LENOVO-81JL-LenovoYOGAC630_13Q50-LNVNB161216.conf
... for board variants. This should scale much better!
This msr is only available when the host supports WAITPKG feature.
This breaks a nested guest, if the L1 hypervisor is set to ignore
unknown msrs, because the only other safety check that the
kernel does is that it attempts to read the msr and
rejects it if it gets an exception.
Cc: stable@vger.kernel.org Fixes: 6e3ba4abce ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL") Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200523161455.3940-3-mlevitsk@redhat.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit f4cfcd2d5aea4e96c5d483c476f3057b6b7baf6a
use boot_cpu_has for checking the feature) Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the SMCCC spec[1](7.5.2 Discovery) the
ARM_SMCCC_ARCH_WORKAROUND_1 function id only returns 0, 1, and
SMCCC_RET_NOT_SUPPORTED.
0 is "workaround required and safe to call this function"
1 is "workaround not required but safe to call this function"
SMCCC_RET_NOT_SUPPORTED is "might be vulnerable or might not be, who knows, I give up!"
SMCCC_RET_NOT_SUPPORTED might as well mean "workaround required, except
calling this function may not work because it isn't implemented in some
cases". Wonderful. We map this SMC call to
0 is SPECTRE_MITIGATED
1 is SPECTRE_UNAFFECTED
SMCCC_RET_NOT_SUPPORTED is SPECTRE_VULNERABLE
For KVM hypercalls (hvc), we've implemented this function id to return
SMCCC_RET_NOT_SUPPORTED, 0, and SMCCC_RET_NOT_REQUIRED. One of those
isn't supposed to be there. Per the code we call
arm64_get_spectre_v2_state() to figure out what to return for this
feature discovery call.
0 is SPECTRE_MITIGATED
SMCCC_RET_NOT_REQUIRED is SPECTRE_UNAFFECTED
SMCCC_RET_NOT_SUPPORTED is SPECTRE_VULNERABLE
Let's clean this up so that KVM tells the guest this mapping:
0 is SPECTRE_MITIGATED
1 is SPECTRE_UNAFFECTED
SMCCC_RET_NOT_SUPPORTED is SPECTRE_VULNERABLE
Note: SMCCC_RET_NOT_AFFECTED is 1 but isn't part of the SMCCC spec
Fixes: c118bbb52743 ("arm64: KVM: Propagate full Spectre v2 workaround state to KVM guests") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Marc Zyngier <maz@kernel.org> Acked-by: Will Deacon <will@kernel.org> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Steven Price <steven.price@arm.com> Cc: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://developer.arm.com/documentation/den0028/latest Link: https://lore.kernel.org/r/20201023154751.1973872-1-swboyd@chromium.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output. An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.
It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack. Oops.
This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key. (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.) Speed is prioritized over security;
attacks are rare, while performance is always wanted.
Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution. This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Eric Dumazet <edumazet@google.com> Cc: "Jason A. Donenfeld" <Jason@zx2c4.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: tytso@mit.edu Cc: Florian Westphal <fw@strlen.de> Cc: Marc Plumb <lkml.mplumb@gmail.com> Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity") Signed-off-by: George Spelvin <lkml@sdf.org> Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec3b5c; moved SIPROUND definitions
to prandom.h for later use; merged George's prandom_seed() proposal;
inlined siprand_u32(); replaced the net_rand_state[] array with 4
members to fix a build issue; cosmetic cleanups to make checkpatch
happy; fixed RANDOM32_SELFTEST build ] Signed-off-by: Willy Tarreau <w@1wt.eu>
[wt: backported to 5.4 -- no tracepoint there] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mimic the pre-existing ACPI and Device Tree event log behavior by not
creating the binary_bios_measurements file when the EFI TPM event log is
empty.
This fixes the following NULL pointer dereference that can occur when
reading /sys/kernel/security/tpm0/binary_bios_measurements after the
kernel received an empty event log from the firmware:
In this situation, the bios_event_log pointer in the tpm_bios_log struct
was not NULL but was equal to the ZERO_SIZE_PTR (0x10) value. This was
due to the following kmemdup() in tpm_read_log_efi():
int tpm_read_log_efi(struct tpm_chip *chip)
{
...
/* malloc EventLog space */
log->bios_event_log = kmemdup(log_tbl->log, log_size, GFP_KERNEL);
if (!log->bios_event_log) {
ret = -ENOMEM;
goto out;
}
...
}
When log_size is zero, due to an empty event log from firmware,
ZERO_SIZE_PTR is returned from kmemdup(). Upon a read of the
binary_bios_measurements file, the tpm2_bios_measurements_start()
function does not perform a ZERO_OR_NULL_PTR() check on the
bios_event_log pointer before dereferencing it.
Rather than add a ZERO_OR_NULL_PTR() check in functions that make use of
the bios_event_log pointer, simply avoid creating the
binary_bios_measurements_file as is done in other event log retrieval
backends.
Explicitly ignore all of the events in the final event log when the main
event log is empty. The list of events in the final event log cannot be
accurately parsed without referring to the first event in the main event
log (the event log header) so the final event log is useless in such a
situation.
Fixes: 58cc1e4faf10 ("tpm: parse TPM event logs based on EFI table") Link: https://lore.kernel.org/linux-integrity/E1FDCCCB-CA51-4AEE-AC83-9CDE995EAE52@canonical.com/ Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-by: Kenneth R. Crudup <kenny@panix.com> Reported-by: Mimi Zohar <zohar@linux.ibm.com> Cc: Thiébaud Weksteen <tweek@google.com> Cc: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to expose non-zeroed post-EOF data in XFS if the new
EOF page is dirty, backed by an unwritten block and the truncate
happens to race with writeback. iomap_truncate_page() will not zero
the post-EOF portion of the page if the underlying block is
unwritten. The subsequent call to truncate_setsize() will, but
doesn't dirty the page. Therefore, if writeback happens to complete
after iomap_truncate_page() (so it still sees the unwritten block)
but before truncate_setsize(), the cached page becomes inconsistent
with the on-disk block. A mapped read after the associated page is
reclaimed or invalidated exposes non-zero post-EOF data.
For example, consider the following sequence when run on a kernel
modified to explicitly flush the new EOF page within the race
window:
$ xfs_io -fc "falloc 0 4k" -c fsync /mnt/file
$ xfs_io -c "pwrite 0 4k" -c "truncate 1k" /mnt/file
...
$ xfs_io -c "mmap 0 4k" -c "mread -v 1k 8" /mnt/file 00000400: 00 00 00 00 00 00 00 00 ........
$ umount /mnt/; mount <dev> /mnt/
$ xfs_io -c "mmap 0 4k" -c "mread -v 1k 8" /mnt/file 00000400: cd cd cd cd cd cd cd cd ........
Update xfs_setattr_size() to explicitly flush the new EOF page prior
to the page truncate to ensure iomap has the latest state of the
underlying block.
Fixes: 68a9f5e7007c ("xfs: implement iomap based buffered write path") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With below sequence, we can see wakeup default is enabled after re-load module,
if it was enabled before, so we need disable wakeup in flexcan_remove().
After double check with Layerscape CAN owner (Pankaj Bansal), confirm that
LS1021A doesn't support ECC feature, so remove FLEXCAN_QUIRK_DISABLE_MECR
quirk.
Fixes: 99b7668c04b27 ("can: flexcan: adding platform specific details for LS1021A") Cc: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20201020155402.30318-4-qiangqing.zhang@nxp.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Echo management is driven by PUCAN_MSG_LOOPED_BACK bit, while loopback
frames are identified with PUCAN_MSG_SELF_RECEIVE bit. Those bits are set
for each outgoing frame written to the IP core so that a copy of each one
will be placed into the rx path. Thus,
- when PUCAN_MSG_LOOPED_BACK is set then the rx frame is an echo of a
previously sent frame,
- when PUCAN_MSG_LOOPED_BACK+PUCAN_MSG_SELF_RECEIVE are set, then the rx
frame is an echo AND a loopback frame. Therefore, this frame must be
put into the socket rx path too.
This patch fixes how CAN frames are handled when these are sent while the
can interface is configured in "loopback on" mode.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Link: https://lore.kernel.org/r/20201013153947.28012-1-s.grosjean@peak-system.com Fixes: 8ac8321e4a79 ("can: peak: add support for PEAK PCAN-PCIe FD CAN-FD boards") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabian Inostroza <fabianinostrozap@gmail.com> has discovered a potential
problem in the hardware timestamp reporting from the PCAN-USB USB CAN interface
(only), related to the fact that a timestamp of an event may precede the
timestamp used for synchronization when both records are part of the same USB
packet. However, this case was used to detect the wrapping of the time counter.
This patch details and fixes the two identified cases where this problem can
occur.
These values come from skb->data so Smatch considers them untrusted. I
believe Smatch is correct but I don't have a way to test this.
The usb_if->dev[] array has 2 elements but the index is in the 0-15
range without checks. The cfd->len can be up to 255 but the maximum
valid size is CANFD_MAX_DLEN (64) so that could lead to memory
corruption.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200813140604.GA456946@mwanda Acked-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count. Call pm_runtime_put if
pm_runtime_get_sync fails.
When a netdev down event occurs after a successful call to
j1939_sk_bind(), j1939_netdev_notify() can handle it correctly.
But if the netdev already in down state before calling j1939_sk_bind(),
j1939_sk_release() will stay in wait_event_interruptible() blocked
forever. Because in this case, j1939_netdev_notify() won't be called and
j1939_tp_txtimer() won't call j1939_session_cancel() or other function
to clear session for ENETDOWN error, this lead to mismatch of
j1939_session_get/put() and jsk->skb_pending will never decrease to
zero.
To reproduce it use following commands:
1. ip link add dev vcan0 type vcan
2. j1939acd -r 100,80-120 1122334455667788 vcan0
3. presses ctrl-c and thread will be blocked forever
This patch adds check for ndev->flags in j1939_sk_bind() to avoid this
kind of situation and return with -ENETDOWN.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1599460308-18770-1-git-send-email-zhangchangzhong@huawei.com Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
All user space generated SKBs are owned by a socket (unless injected into the
key via AF_PACKET). If a socket is closed, all associated skbs will be cleaned
up.
This leads to a problem when a CAN driver calls can_put_echo_skb() on a
unshared SKB. If the socket is closed prior to the TX complete handler,
can_get_echo_skb() and the subsequent delivering of the echo SKB to all
registered callbacks, a SKB with a refcount of 0 is delivered.
To avoid the problem, in can_get_echo_skb() the original SKB is now always
cloned, regardless of shared SKB or not. If the process exists it can now
safely discard its SKBs, without disturbing the delivery of the echo SKB.
The problem shows up in the j1939 stack, when it clones the incoming skb, which
detects the already 0 refcount.
We can easily reproduce this with following example:
The can_get_echo_skb() function returns the number of received bytes to
be used for netdev statistics. In the case of RTR frames we get a valid
(potential non-zero) data length value which has to be passed for further
operations. But on the wire RTR frames have no payload length. Therefore
the value to be used in the statistics has to be zero for RTR frames.
Reported-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201020064443.80164-1-socketcan@hartkopp.net Fixes: cf5046b309b3 ("can: dev: let can_get_echo_skb() return dlc of CAN frame") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a driver calls can_get_echo_skb() during a hardware IRQ (which is often, but
not always, the case), the 'WARN_ON(in_irq)' in
net/core/skbuff.c#skb_release_head_state() might be triggered, under network
congestion circumstances, together with the potential risk of a NULL pointer
dereference.
The root cause of this issue is the call to kfree_skb() instead of
dev_kfree_skb_irq() in net/core/dev.c#enqueue_to_backlog().
This patch prevents the skb to be freed within the call to netif_rx() by
incrementing its reference count with skb_get(). The skb is finally freed by
one of the in-irq-context safe functions: dev_consume_skb_any() or
dev_kfree_skb_any(). The "any" version is used because some drivers might call
can_get_echo_skb() in a normal context.
The reason for this issue to occur is that initially, in the core network
stack, loopback skb were not supposed to be received in hardware IRQ context.
The CAN stack is an exeption.
This bug was previously reported back in 2017 in [1] but the proposed patch
never got accepted.
While [1] directly modifies net/core/dev.c, we try to propose here a
smoother modification local to CAN network stack (the assumption
behind is that only CAN devices are affected by this issue).
A CAN driver, using the rx-offload infrastructure, is reading CAN frames
(usually in IRQ context) from the hardware and placing it into the rx-offload
queue to be delivered to the networking stack via NAPI.
In case the rx-offload queue is full, trying to add more skbs results in the
skbs being dropped using kfree_skb(). If done from hard-IRQ context this
results in the following warning:
[ 682.552693] ------------[ cut here ]------------
[ 682.557360] WARNING: CPU: 0 PID: 3057 at net/core/skbuff.c:650 skb_release_head_state+0x74/0x84
[ 682.566075] Modules linked in: can_raw can coda_vpu flexcan dw_hdmi_ahb_audio v4l2_jpeg imx_vdoa can_dev
[ 682.575597] CPU: 0 PID: 3057 Comm: cansend Tainted: G W 5.7.0+ #18
[ 682.583098] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 682.589657] [<c0112628>] (unwind_backtrace) from [<c010c1c4>] (show_stack+0x10/0x14)
[ 682.597423] [<c010c1c4>] (show_stack) from [<c06c481c>] (dump_stack+0xe0/0x114)
[ 682.604759] [<c06c481c>] (dump_stack) from [<c0128f10>] (__warn+0xc0/0x10c)
[ 682.611742] [<c0128f10>] (__warn) from [<c0129314>] (warn_slowpath_fmt+0x5c/0xc0)
[ 682.619248] [<c0129314>] (warn_slowpath_fmt) from [<c0b95dec>] (skb_release_head_state+0x74/0x84)
[ 682.628143] [<c0b95dec>] (skb_release_head_state) from [<c0b95e08>] (skb_release_all+0xc/0x24)
[ 682.636774] [<c0b95e08>] (skb_release_all) from [<c0b95eac>] (kfree_skb+0x74/0x1c8)
[ 682.644479] [<c0b95eac>] (kfree_skb) from [<bf001d1c>] (can_rx_offload_queue_sorted+0xe0/0xe8 [can_dev])
[ 682.654051] [<bf001d1c>] (can_rx_offload_queue_sorted [can_dev]) from [<bf001d6c>] (can_rx_offload_get_echo_skb+0x48/0x94 [can_dev])
[ 682.666007] [<bf001d6c>] (can_rx_offload_get_echo_skb [can_dev]) from [<bf01efe4>] (flexcan_irq+0x194/0x5dc [flexcan])
[ 682.676734] [<bf01efe4>] (flexcan_irq [flexcan]) from [<c019c1ec>] (__handle_irq_event_percpu+0x4c/0x3ec)
[ 682.686322] [<c019c1ec>] (__handle_irq_event_percpu) from [<c019c5b8>] (handle_irq_event_percpu+0x2c/0x88)
[ 682.695993] [<c019c5b8>] (handle_irq_event_percpu) from [<c019c64c>] (handle_irq_event+0x38/0x5c)
[ 682.704887] [<c019c64c>] (handle_irq_event) from [<c01a1058>] (handle_fasteoi_irq+0xc8/0x180)
[ 682.713432] [<c01a1058>] (handle_fasteoi_irq) from [<c019b2c0>] (generic_handle_irq+0x30/0x44)
[ 682.722063] [<c019b2c0>] (generic_handle_irq) from [<c019b8f8>] (__handle_domain_irq+0x64/0xdc)
[ 682.730783] [<c019b8f8>] (__handle_domain_irq) from [<c06df4a4>] (gic_handle_irq+0x48/0x9c)
[ 682.739158] [<c06df4a4>] (gic_handle_irq) from [<c0100b30>] (__irq_svc+0x70/0x98)
[ 682.746656] Exception stack(0xe80e9dd8 to 0xe80e9e20)
[ 682.751725] 9dc0: 00000001e80e8000
[ 682.759922] 9de0: e820cf8000000000ffffe00000000000eaf08fe400000000600d001300000000
[ 682.768117] 9e00: c1732e3cc16093a8e820d4c0e80e9e28c018a57cc018b870600d0013ffffffff
[ 682.776315] [<c0100b30>] (__irq_svc) from [<c018b870>] (lock_acquire+0x108/0x4e8)
[ 682.783821] [<c018b870>] (lock_acquire) from [<c0e938e4>] (down_write+0x48/0xa8)
[ 682.791242] [<c0e938e4>] (down_write) from [<c02818dc>] (unlink_file_vma+0x24/0x40)
[ 682.798922] [<c02818dc>] (unlink_file_vma) from [<c027a258>] (free_pgtables+0x34/0xb8)
[ 682.806858] [<c027a258>] (free_pgtables) from [<c02835a4>] (exit_mmap+0xe4/0x170)
[ 682.814361] [<c02835a4>] (exit_mmap) from [<c01248e0>] (mmput+0x5c/0x110)
[ 682.821171] [<c01248e0>] (mmput) from [<c012e910>] (do_exit+0x374/0xbe4)
[ 682.827892] [<c012e910>] (do_exit) from [<c0130888>] (do_group_exit+0x38/0xb4)
[ 682.835132] [<c0130888>] (do_group_exit) from [<c0130914>] (__wake_up_parent+0x0/0x14)
[ 682.843063] irq event stamp: 1936
[ 682.846399] hardirqs last enabled at (1935): [<c02938b0>] rmqueue+0xf4/0xc64
[ 682.853553] hardirqs last disabled at (1936): [<c0100b20>] __irq_svc+0x60/0x98
[ 682.860799] softirqs last enabled at (1878): [<bf04cdcc>] raw_release+0x108/0x1f0 [can_raw]
[ 682.869256] softirqs last disabled at (1876): [<c0b8f478>] release_sock+0x18/0x98
[ 682.876753] ---[ end trace 7bca4751ce44c444 ]---
This patch fixes the problem by replacing the kfree_skb() by
dev_kfree_skb_any(), as rx-offload might be called from threaded IRQ handlers
as well.
When using the afs.yfs.acl xattr to change an AuriStor ACL, a warning
can be generated when the request is marshalled because the buffer
pointer isn't increased after adding the last element, thereby
triggering the check at the end if the ACL wasn't empty. This just
causes something like the following warning, but doesn't stop the call
from happening successfully:
In prq_event_thread(), the QI_PGRP_PDP is wrongly set by
'req->pasid_present' which should be replaced to
'req->priv_data_present'.
Fixes: 5b438f4ba315 ("iommu/vt-d: Support page request in scalable mode") Signed-off-by: Liu, Yi L <yi.l.liu@intel.com> Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/1604025444-6954-3-git-send-email-yi.y.sun@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lockdep complains that a possible deadlock below in
eeh_addr_cache_show() because it is acquiring a lock with IRQ enabled,
but eeh_addr_cache_insert_dev() needs to acquire the same lock with IRQ
disabled. Let's just make eeh_addr_cache_show() acquire the lock with
IRQ disabled as well.
Fixes: 5ca85ae6318d ("powerpc/eeh_cache: Add a way to dump the EEH address cache") Signed-off-by: Qian Cai <cai@redhat.com> Reviewed-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201028152717.8967-1-cai@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In ip_set_match_extensions(), for sets with counters, we take care of
updating counters themselves by calling ip_set_update_counter(), and of
checking if the given comparison and values match, by calling
ip_set_match_counter() if needed.
However, if a given comparison on counters doesn't match the configured
values, that doesn't mean the set entry itself isn't matching.
This fix restores the behaviour we had before commit 4750005a85f7
("netfilter: ipset: Fix "don't update counters" mode when counters used
at the matching"), without reintroducing the issue fixed there: back
then, mtype_data_match() first updated counters in any case, and then
took care of matching on counters.
Now, if the IPSET_FLAG_SKIP_COUNTER_UPDATE flag is set,
ip_set_update_counter() will anyway skip counter updates if desired.
The issue observed is illustrated by this reproducer:
ipset create c hash:ip counters
ipset add c 192.0.2.1
iptables -I INPUT -m set --match-set c src --bytes-gt 800 -j DROP
if we now send packets from 192.0.2.1, bytes and packets counters
for the entry as shown by 'ipset list' are always zero, and, no
matter how many bytes we send, the rule will never match, because
counters themselves are not updated.
Reported-by: Mithil Mhatre <mmhatre@redhat.com> Fixes: 4750005a85f7 ("netfilter: ipset: Fix "don't update counters" mode when counters used at the matching") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If userspace does not include the trailing end of batch message, then
nfnetlink aborts the transaction. This allows to check that ruleset
updates trigger no errors.
After this patch, invoking this command from the prerouting chain:
# nft -c add rule x y fib saddr . oif type local
fails since oif is not supported there.
This patch fixes the lack of rule validation from the abort/check path
to catch configuration errors such as the one above.
If netfilter changes the packet mark when mangling, the packet is
rerouted using the route_me_harder set of functions. Prior to this
commit, there's one big difference between route_me_harder and the
ordinary initial routing functions, described in the comment above
__ip_queue_xmit():
/* Note: skb->sk can be different from sk, in case of tunnels */
int __ip_queue_xmit(struct sock *sk, struct sk_buff *skb, struct flowi *fl,
That function goes on to correctly make use of sk->sk_bound_dev_if,
rather than skb->sk->sk_bound_dev_if. And indeed the comment is true: a
tunnel will receive a packet in ndo_start_xmit with an initial skb->sk.
It will make some transformations to that packet, and then it will send
the encapsulated packet out of a *new* socket. That new socket will
basically always have a different sk_bound_dev_if (otherwise there'd be
a routing loop). So for the purposes of routing the encapsulated packet,
the routing information as it pertains to the socket should come from
that socket's sk, rather than the packet's original skb->sk. For that
reason __ip_queue_xmit() and related functions all do the right thing.
One might argue that all tunnels should just call skb_orphan(skb) before
transmitting the encapsulated packet into the new socket. But tunnels do
*not* do this -- and this is wisely avoided in skb_scrub_packet() too --
because features like TSQ rely on skb->destructor() being called when
that buffer space is truely available again. Calling skb_orphan(skb) too
early would result in buffers filling up unnecessarily and accounting
info being all wrong. Instead, additional routing must take into account
the new sk, just as __ip_queue_xmit() notes.
So, this commit addresses the problem by fishing the correct sk out of
state->sk -- it's already set properly in the call to nf_hook() in
__ip_local_out(), which receives the sk as part of its normal
functionality. So we make sure to plumb state->sk through the various
route_me_harder functions, and then make correct use of it following the
example of __ip_queue_xmit().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that we actually initialize xefi_discard when we're scheduling
a deferred free of an AGFL block. This was (eventually) found by the
UBSAN while I was banging on realtime rmap problems, but it exists in
the upstream codebase. While we're at it, rearrange the structure to
reduce the struct size from 64 to 56 bytes.
Fixes: fcb762f5de2e ("xfs: add bmapi nodiscard flag") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
we found that the following race condition exists in
xfrm_alloc_userspi flow:
user thread state_hash_work thread
---- ----
xfrm_alloc_userspi()
__find_acq_core()
/*alloc new xfrm_state:x*/
xfrm_state_alloc()
/*schedule state_hash_work thread*/
xfrm_hash_grow_check() xfrm_hash_resize()
xfrm_alloc_spi /*hold lock*/
x->id.spi = htonl(spi) spin_lock_bh(&net->xfrm.xfrm_state_lock)
/*waiting lock release*/ xfrm_hash_transfer()
spin_lock_bh(&net->xfrm.xfrm_state_lock) /*add x into hlist:net->xfrm.state_byspi*/
hlist_add_head_rcu(&x->byspi)
spin_unlock_bh(&net->xfrm.xfrm_state_lock)
/*add x into hlist:net->xfrm.state_byspi 2 times*/
hlist_add_head_rcu(&x->byspi)
1. a new state x is alloced in xfrm_state_alloc() and added into the bydst hlist
in __find_acq_core() on the LHS;
2. on the RHS, state_hash_work thread travels the old bydst and tranfers every xfrm_state
(include x) into the new bydst hlist and new byspi hlist;
3. user thread on the LHS gets the lock and adds x into the new byspi hlist again.
So the same xfrm_state (x) is added into the same list_hash
(net->xfrm.state_byspi) 2 times that makes the list_hash become
an inifite loop.
To fix the race, x->id.spi = htonl(spi) in the xfrm_alloc_spi() is moved
to the back of spin_lock_bh, sothat state_hash_work thread no longer add x
which id.spi is zero into the hash_list.
It is not an error if the host requests to balloon down, but the VM
refuses to do so. Without this change a warning is logged in dmesg
every five minutes.
Fixes: b3bb97b8a49f3 ("Drivers: hv: balloon: Add logging for dynamic memory operations") Signed-off-by: Olaf Hering <olaf@aepfle.de> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20201008071216.16554-1-olaf@aepfle.de Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log