The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 1" for this frequency,
which translates to 2550MHz / 7 / 1 = 364285714Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: c3ea80b6138cae ("ARM: dts: meson8b: add the Mali-450 MP2 GPU") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 2" for this frequency,
which translates to 2550MHz / 7 / 2 = 182142857Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.
rcar_sound doesn't support clkout-lr-synchronous in upstream.
It was supported under out-of-tree rcar_sound.
upstream rcar_sound is supporting
- clkout-lr-synchronous
+ clkout-lr-asynchronous
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
commit 664ae1ab2536 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40d3 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.
From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.
Fixes: 5e04822f7db5 ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx") Signed-off-by: Ingo van Lil <inguin@gmx.de> Cc: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msm_serial driver has a predefined set of uart ports defined, which
is allocated either by reading aliases or if no match is found a simple
counter, starting at index 0. But there's no logic in place to prevent
these two allocation mechanism from colliding. As a result either none
or all of the active msm_serial instances must be listed as aliases.
Define blsp1_uart3 as "serial1" to mitigate this problem.
The uDPU uses both ethernet controllers, which ties up COMPHY 0 for
eth1 and COMPHY 1 for eth0, with no USB3 comphy. The addition of
COMPHY support made the kernel override the setup by the boot loader
breaking this platform by assuming that COMPHY 0 was always used for
USB3. Delete the USB3 COMPHY definition at platform level, and add
phy specifications for the ethernet channels.
Fixes: bd3d25b07342 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcsr syscon region is really 0x40000 in size. We need access to the
full region so that we can access the axi resets when managing the
modem subsystem.
The driver gets driver_data from memory that is marked as const (which
is probably put to read-only memory) and it then modifies it. This
likely causes some sort of fault to happen.
Fix this by taking a copy of the structure.
Fixes: c94a8ff14de3 ("platform/x86: intel_mid_powerbtn: make mid_pb_ddata const") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() prints an error message when the interrupt
is not available. So on platforms where bark interrupt is
not specified, following error message is observed on SDM845.
[ 2.975888] qcom_wdt 17980000.watchdog: IRQ index 0 not found
This is also seen on SC7180, SM8150 SoCs as well.
Fix this by using platform_get_irq_optional() instead.
Fixes: 36375491a4395654 ("watchdog: qcom: support pre-timeout when the bark irq is available") Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20191213064934.4112-1-saiprakash.ranjan@codeaurora.org Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtc-cmos interrupt setting was changed in the commit 079062b28fb4
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28fb4 ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1bd ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs") Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code returns -EPERM when the voltage loss bit is set.
Since the bit indicates that the time value is not valid, return
-EINVAL instead, which is the appropriate error code for this
situation.
The devm_request_threaded_irq function allocates irq that is
released when a driver detaches. Thus, there is no reason to
explicitly call free_irq in probe function.
vfnum buffer size and binary_len buffer size is received by user-space.
So, this buffer size could be too large. If so, kmalloc will internally
print a warning message.
This warning message is actually not necessary for the netdevsim module.
So, this patch adds __GFP_NOWARN.
nsim_dev_take_snapshot_write() uses nsim_dev and nsim_dev->dummy_region.
So, during this function, these data shouldn't be removed.
But there is no protecting stuff in this function.
There are two similar cases.
1. reload case
reload could be called during nsim_dev_take_snapshot_write().
When reload is being executed, nsim_dev_reload_down() is called and it
calls nsim_dev_reload_destroy(). nsim_dev_reload_destroy() calls
devlink_region_destroy() to destroy nsim_dev->dummy_region.
So, during nsim_dev_take_snapshot_write(), nsim_dev->dummy_region()
would be removed.
At this point, snapshot_write() would access freed pointer.
In order to fix this case, take_snapshot file will be removed before
devlink_region_destroy().
The take_snapshot file will be re-created by ->reload_up().
2. del_device_store case
del_device_store() also could call nsim_dev_reload_destroy()
during nsim_dev_take_snapshot_write(). If so, panic would occur.
This problem is actually the same problem with the first case.
So, this problem will be fixed by the first case's solution.
Test commands:
modprobe netdevsim
while :
do
echo 1 > /sys/bus/netdevsim/new_device &
echo 1 > /sys/bus/netdevsim/del_device &
devlink dev reload netdevsim/netdevsim1 &
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/take_snapshot &
done
Fixes: 4418f862d675 ("netdevsim: implement support for devlink region and snapshots") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devlink reload destroys resources and allocates resources again.
So, when devices and ports resources are being used, devlink reload
function should not be executed. In order to avoid this race, a new
lock is added and new_port() and del_port() call devlink_reload_disable()
and devlink_reload_enable().
Before Thread1's devlink_reload_enable(), the devlink is already allowed
to execute reload because Thread0 allows it. devlink reload disable/enable
variable type is bool. So the above case would exist.
So, disable/enable should be executed atomically.
In order to do that, a new lock is used.
Test commands:
modprobe netdevsim
echo 1 > /sys/bus/netdevsim/new_device
while :
do
echo 1 > /sys/devices/netdevsim1/new_port &
echo 1 > /sys/devices/netdevsim1/del_port &
devlink dev reload netdevsim/netdevsim1 &
done
When module is being initialized, __init() calls bus_register() and
driver_register().
These functions internally create various resources and sysfs files.
The sysfs files are used for basic operations(add/del device).
/sys/bus/netdevsim/new_device
/sys/bus/netdevsim/del_device
These sysfs files use netdevsim resources, they are mostly allocated
and initialized in ->probe() function, which is nsim_dev_probe().
But, sysfs files could be executed before ->probe() is finished.
So, accessing uninitialized data would occur.
Another problem is very similar.
/sys/bus/netdevsim/new_device internally creates sysfs files.
/sys/devices/netdevsim<id>/new_port
/sys/devices/netdevsim<id>/del_port
These sysfs files also use netdevsim resources, they are mostly allocated
and initialized in creating device routine, which is nsim_bus_dev_new().
But they also could be executed before nsim_bus_dev_new() is finished.
So, accessing uninitialized data would occur.
To fix these problems, this patch adds flags, which means whether the
operation is finished or not.
The flag variable 'nsim_bus_enable' means whether netdevsim bus was
initialized or not.
This is protected by nsim_bus_dev_list_lock.
The flag variable 'nsim_bus_dev->init' means whether nsim_bus_dev was
initialized or not.
This could be used in {new/del}_port_store() with no lock.
Test commands:
#SHELL1
modprobe netdevsim
while :
do
echo "1 1" > /sys/bus/netdevsim/new_device
echo "1 1" > /sys/bus/netdevsim/del_device
done
#SHELL2
while :
do
echo 1 > /sys/devices/netdevsim1/new_port
echo 1 > /sys/devices/netdevsim1/del_port
done
Fixes: f9d9db47d3ba ("netdevsim: add bus attributes to add new and delete devices") Fixes: 794b2c05ca1c ("netdevsim: extend device attrs to support port addition and deletion") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's currently possible to insert sockets in unexpected states into
a sockmap, due to a TOCTTOU when updating the map from a syscall.
sock_map_update_elem checks that sk->sk_state == TCP_ESTABLISHED,
locks the socket and then calls sock_map_update_common. At this
point, the socket may have transitioned into another state, and
the earlier assumptions don't hold anymore. Crucially, it's
conceivable (though very unlikely) that a socket has become unhashed.
This breaks the sockmap's assumption that it will get a callback
via sk->sk_prot->unhash.
Fix this by checking the (fixed) sk_type and sk_protocol without the
lock, followed by a locked check of sk_state.
Unfortunately it's not possible to push the check down into
sock_(map|hash)_update_common, since BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB
run before the socket has transitioned from TCP_SYN_RECV into
TCP_ESTABLISHED.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Lorenz Bauer <lmb@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20200207103713.28175-1-lmb@cloudflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That's one line (the assignment line) that is 2,686,974 characters in
length.
Now, sparse does happen to react particularly badly to that (I didn't
look to why, but I suspect it's just that evaluating all the types
that don't actually ever end up getting used ends up being much more
expensive than it should be), but I bet it's not good for gcc either.
Fixes: 6ac99e8f23d4 ("bpf: Introduce bpf sk local storage") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Link: https://lore.kernel.org/bpf/20200207081810.3918919-1-kafai@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear
down") introduced sleeping issues inside RCU critical sections and while
holding a spinlock on sockmap/sockhash tear-down. There has to be at least
one socket in the map for the problem to surface.
This adds a test that triggers the warnings for broken locking rules. Not a
fix per se, but rather tooling to verify the accompanying fixes. Run on a
VM with 1 vCPU to reproduce the warnings.
Fixes: 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear down") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-4-jakub@cloudflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc90e ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rcu_read_lock is needed to protect access to psock inside sock_map_unref
when tearing down the map. However, we can't afford to sleep in lock_sock
while in RCU read-side critical section. Grab the RCU lock only after we
have locked the socket.
This fixes RCU warnings triggerable on a VM with 1 vCPU when free'ing a
sockmap/sockhash that contains at least one socket:
Turns out the xlated program instructions can also be missing if
kptr_restrict sysctl is set. This means that the previous fix to check the
jited_prog_insns pointer was insufficient; add another check of the
xlated_prog_insns pointer as well.
Fixes: 5b79bcdf0362 ("bpftool: Don't crash on missing jited insns or ksyms") Fixes: cae73f233923 ("bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20200206102906.112551-1-toke@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break an infinite loop when early parsing of the SRAT table is caused
by a subtable with zero length. Known to affect the ASUS WS X299 SAGE
motherboard with firmware version 1201 which has a large block of
zeros in its SRAT table. The kernel could boot successfully on this
board/firmware prior to the introduction of early parsing this table or
after a BIOS update.
[ bp: Fixup whitespace damage and commit message. Make it return 0 to
denote that there are no immovable regions because who knows what
else is broken in this BIOS. ]
Currently, each time nfs4_do_fsinfo() is called it will do an implicit
NFS4 lease renewal, which is not compliant with the NFS4 specification.
This can result in a lease being expired by an NFS server.
Commit 83ca7f5ab31f ("NFS: Avoid PUTROOTFH when managing leases")
introduced implicit client lease renewal in nfs4_do_fsinfo(),
which can result in the NFSv4.0 lease to expire on a server side,
and servers returning NFS4ERR_EXPIRED or NFS4ERR_STALE_CLIENTID.
This can easily be reproduced by frequently unmounting a sub-mount,
then stat'ing it to get it mounted again, which will delay or even
completely prevent client from sending RENEW operations if no other
NFS operations are issued. Eventually nfs server will expire client's
lease and return an error on file access or next RENEW.
This can also happen when a sub-mount is automatically unmounted
due to inactivity (after nfs_mountpoint_expiry_timeout), then it is
mounted again via stat(). This can result in a short window during
which client's lease will expire on a server but not on a client.
This specific case was observed on production systems.
This patch removes the implicit lease renewal from nfs4_do_fsinfo().
Fixes: 83ca7f5ab31f ("NFS: Avoid PUTROOTFH when managing leases") Signed-off-by: Robert Milkowski <rmilkowski@gmail.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of making assumptions about the commit verifier contents, change
the commit code to ensure we always check that the verifier was set
by the XDR code.
Fixes: f54bcf2ecee9 ("pnfs: Prepare for flexfiles by pulling out common code") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we suffer a fatal error upon writing a file, which causes us to
need to revalidate the entire mapping, then we should also revalidate
the file size.
Fixes: d2ceb7e57086 ("NFS: Don't use page_file_mapping after removing the page") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SWAP=n, it does not make much sense to offer the user the
option to enable support for swapping over NFS, as that will still fail
at run time:
# swapon /swap
swapon: /swap: swapon failed: Function not implemented
Fix this by adding a dependency on CONFIG_SWAP.
Fixes: a564b8f0398636ba ("nfs: enable swap on NFS") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since the commit 0e0cb35b417f, it's possible to lose an open stateid
while retrying a CLOSE due to ERR_OLD_STATEID. Once that happens,
operations that require openstateid fail with EAGAIN which is propagated
to the application then tests like generic/446 and generic/168 fail with
"Resource temporarily unavailable".
Instead of returning this error, initiate state recovery when possible to
recover the open stateid and then try calling nfs4_select_rw_stateid()
again.
Fixes: 0e0cb35b417f ("NFSv4: Handle NFS4ERR_OLD_STATEID in CLOSE/OPEN_DOWNGRADE") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On netdev down event, nf_flow_table_cleanup() is called for the relevant
device and it cleans all the tables that are on that device.
If one of those tables has hardware offload flag,
nf_flow_table_iterate_cleanup flushes hardware and then runs the gc.
But the gc can queue more hardware work, which will take time to execute.
Instead first add the work, then flush it, to execute it now.
Fixes: c29f74e0df7a ("netfilter: nf_flow_table: hardware offload support") Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not fetch statistics if flow has expired since it might not in
hardware anymore. After this update, remove the FLOW_OFFLOAD_HW_DYING
check from nf_flow_offload_stats() since this flag is never set on.
I changed the API for asking for a session protection but
I omitted the TDLS flows. Fix that now.
Note that for the TDLS flow, we need to block until the
session protection actually starts, so add this option
to iwl_mvm_schedule_session_protection.
This patch fixes a firmware assert in the TDLS flow since
the old TIME_EVENT_CMD is not supported anymore by newer
firwmare versions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Fixes: fe959c7b2049 ("iwlwifi: mvm: use the new session protection command") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com> Fixes: fc36ffda3267 ("iwlwifi: mvm: support FTM initiator") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad71 ("PCI: update bridge resources to get more big ranges when allocating space (again)") Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()] Reported-by: Kit Chow <kchow@gigaio.com> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix AFI_PEX2_CTRL reg offset for Tegra30 by moving it from the Tegra20
SoC struct where it erroneously got added. This fixes the AFI_PEX2_CTRL
reg offset being uninitialised subsequently failing to bring up the
third PCIe port.
Fixes: adb2653b3d2e ("PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct") Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_set_mask_and_coherent() instead of dma_set_coherent_mask() as the
Switchtec hardware fully supports 64bit addressing and we should set both
the streaming and coherent masks the same.
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6706 ("ath10k: add memory dump support QCA9984") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the implementation of pci_iov_add_virtfn() the allocated virtfn is
leaked if pci_setup_device() fails. The error handling is not calling
pci_stop_and_remove_bus_device(). Change the goto label to failed2.
A non-zero error value likely being returned by ufshcd_scsi_add_wlus() in
case of failure of adding the WLs, but ufshcd_probe_hba() doesn't use this
value, and doesn't report this failure to upper caller. This patch is to
fix this issue.
Fixes: 2a8fa600445c ("ufs: manually add well known logical units") Link: https://lore.kernel.org/r/20200120130820.1737-2-huobean@gmail.com Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Except for the last entry, the ending iova alignment sets the maximum
possible page size as the low bits of the iova must be zero when starting
the next chunk.
Fixes: 4a35339958f1 ("RDMA/umem: Add API to find best driver supported page size in an MR") Link: https://lore.kernel.org/r/20200128135612.174820-1-leon@kernel.org Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Gal Pressman <galpress@amazon.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below commit missed the AF_IB and loopback code flow in
rdma_resolve_addr(). This leads to an unbalanced cm_id refcount in
cma_work_handler() which puts the refcount which was not incremented prior
to queuing the work.
The set of entry->driver_removed is missing locking, protect it with
xa_lock() which is held by the only reader.
Otherwise readers may continue to see driver_removed = false after
rdma_user_mmap_entry_remove() returns and may continue to try and
establish new mmaps.
Fixes: 3411f9f01b76 ("RDMA/core: Create mmap database and cookie helper functions") Link: https://lore.kernel.org/r/20200115202041.GA17199@ziepe.ca Reviewed-by: Gal Pressman <galpress@amazon.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Till recently it was not possible for userspace to specify a different
IOVA, but with the new ibv_reg_mr_iova() library call this can be done.
To compute the user_va we must compute:
user_va = (iova - iova_start) + user_va_start
while being cautious of overflow and other math problems.
The iova is not reliably stored in the mmkey when the MR is created. Only
the cached creation path (the common one) set it, so it must also be set
when creating uncached MRs.
Fix the weird use of iova when computing the starting page index in the
MR. In the normal case, when iova == umem.address:
iova & (~(BIT(page_shift) - 1)) ==
ALIGN_DOWN(umem.address, odp->page_size) ==
ib_umem_start(odp)
And when iova is different using it in math with a user_va is wrong.
Finally, do not allow an implicit ODP to be created with a non-zero IOVA
as we have no support for that.
Fixes: 7bdf65d411c1 ("IB/mlx5: Handle page faults") Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should not be using ib_dev to test for disassociation, during
disassociation is_closed is set under lock and the waitq is triggered.
Instead check is_closed and be sure to re-obtain the lock to test the
value after the wait_event returns.
Fixes: 036b10635739 ("IB/uverbs: Enable device removal when there are active user space applications") Link: https://lore.kernel.org/r/1578504126-9400-12-git-send-email-yishaih@mellanox.com Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rdma_nl_rcv_skb(), the local variable err is assigned the return value
of the supplied callback function, which could be one of
ib_nl_handle_resolve_resp(), ib_nl_handle_set_timeout(), or
ib_nl_handle_ip_res_resp(). These three functions all return skb->len on
success.
rdma_nl_rcv_skb() is merely a copy of netlink_rcv_skb(). The callback
functions used by the latter have the convention: "Returns 0 on success or
a negative error code".
In particular, the statement (equal for both functions):
if (nlh->nlmsg_flags & NLM_F_ACK || err)
implies that rdma_nl_rcv_skb() always will ack a message, independent of
the NLM_F_ACK being set in nlmsg_flags or not.
The fix could be to change the above statement, but it is better to keep
the two *_rcv_skb() functions equal in this respect and instead change the
three callback functions in the rdma subsystem to the correct convention.
Fixes: 2ca546b92a02 ("IB/sa: Route SA pathrecord query through netlink") Fixes: ae43f8286730 ("IB/core: Add IP to GID netlink offload") Link: https://lore.kernel.org/r/20191216120436.3204814-1-haakon.bugge@oracle.com Suggested-by: Mark Haywood <mark.haywood@oracle.com> Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Tested-by: Mark Haywood <mark.haywood@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.
Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping in
a cache.
Following the RDMA Connection Manager (CM) protocol, it is clear when an
entry has to evicted from the cache. When a DREP is sent from
mlx4_ib_multiplex_cm_handler(), id_map_find_del() is called. Similar when
a REJ is received by the mlx4_ib_demux_cm_handler(), id_map_find_del() is
called.
This function wipes out the TID in use from the IDR or XArray and removes
the id_map_entry from the table.
In short, it does everything except the topping of the cake, which is to
remove the entry from the list and free it. In other words, for the REJ
case enumerated above, one id_map_entry will be leaked.
For the other case above, a DREQ has been received first. The reception of
the DREQ will trigger queuing of a delayed work to delete the
id_map_entry, for the case where the VM doesn't send back a DREP.
In the normal case, the VM _will_ send back a DREP, and id_map_find_del()
will be called.
But this scenario introduces a secondary leak. First, when the DREQ is
received, a delayed work is queued. The VM will then return a DREP, which
will call id_map_find_del(). As stated above, this will free the TID used
from the XArray or IDR. Now, there is window where that particular TID can
be re-allocated, lets say by an outgoing REQ. This TID will later be wiped
out by the delayed work, when the function id_map_ent_timeout() is
called. But the id_map_entry allocated by the outgoing REQ will not be
de-allocated, and we have a leak.
Both leaks are fixed by removing the id_map_find_del() function and only
using schedule_delayed(). Of course, a check in schedule_delayed() to see
if the work already has been queued, has been added.
Another benefit of always using the delayed version for deleting entries,
is that we do get a TimeWait effect; a TID no longer in use, will occupy
the XArray or IDR for CM_CLEANUP_CACHE_TIMEOUT time, without any ability
of being re-used for that time period.
A user can change the operational GUID (a.k.a affective GUID) through
link/infiniband. Therefore it is preferred to return the currently set
GUID if it exists instead of the operational.
This way the PF can query which VF GUID will be set in the next bind. In
order to align with MAC address, zero is returned if administrative GUID
is not set.
For example, before setting administrative GUID:
$ ip link show
ib0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 4092 qdisc mq state UP mode DEFAULT group default qlen 256
link/infiniband 00:00:00:08:fe:80:00:00:00:00:00:00:52:54:00:c0:fe:12:34:55 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband 00:00:00:08:fe:80:00:00:00:00:00:00:52:54:00:c0:fe:12:34:55 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff,
spoof checking off, NODE_GUID 00:00:00:00:00:00:00:00, PORT_GUID 00:00:00:00:00:00:00:00, link-state auto, trust off, query_rss off
Then:
$ ip link set ib0 vf 0 node_guid 11:00:af:21:cb:05:11:00
$ ip link set ib0 vf 0 port_guid 22:11:af:21:cb:05:11:00
After setting administrative GUID:
$ ip link show
ib0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 4092 qdisc mq state UP mode DEFAULT group default qlen 256
link/infiniband 00:00:00:08:fe:80:00:00:00:00:00:00:52:54:00:c0:fe:12:34:55 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband 00:00:00:08:fe:80:00:00:00:00:00:00:52:54:00:c0:fe:12:34:55 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff,
spoof checking off, NODE_GUID 11:00:af:21:cb:05:11:00, PORT_GUID 22:11:af:21:cb:05:11:00, link-state auto, trust off, query_rss off
Fixes: 9c0015ef0928 ("IB/mlx5: Implement callbacks for getting VFs GUID attributes") Link: https://lore.kernel.org/r/20200116120048.12744-1-leon@kernel.org Signed-off-by: Danit Goldberg <danitg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SRP targets that do not support specification SRP-2, put the garbage
to the reserved bits of the SRP login response. The problem was not
detected for a long time because the SRP initiator ignored those bits. But
now one of them is used as SRP_LOGIN_RSP_IMMED_SUPP. And it causes a
critical error on the target when the initiator sends immediate data.
The ib_srp module has a use_imm_date parameter to enable or disable
immediate data manually. But it does not help in the above case, because
use_imm_date is ignored at handling the SRP login response. The problem is
definitely caused by a bug on the target side, but the initiator's
behavior also does not look correct. The initiator should not use
immediate data if use_imm_date is disabled by a user.
This commit adds an additional checking of use_imm_date at the handling of
SRP login response to avoid unexpected use of immediate data.
Fixes: 882981f4a411 ("RDMA/srp: Add support for immediate data") Link: https://lore.kernel.org/r/20200115133055.30232-1-sergeygo@mellanox.com Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In procedure mlx4_ib_add_gid(), if the driver is unable to update the FW
gid table, there is a memory leak in the driver's copy of the gid table:
the gid entry's context buffer is not freed.
If such an error occurs, free the entry's context buffer, and mark the
entry as available (by setting its context pointer to NULL).
Fixes: e26be1bfef81 ("IB/mlx4: Implement ib_device callbacks") Link: https://lore.kernel.org/r/20200115085050.73746-1-leon@kernel.org Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use compat_* type defininitions in device drivers
outside of CONFIG_COMPAT, move the inclusion of asm-generic/compat.h
ahead of the #ifdef.
All other architectures already do this.
Acked-by: Will Deacon <will@kernel.org> Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CTR transfer works in fragments of data of maximum 1 MByte because
of the 16 bit CTR counter embedded in the IP. Fix the CTR counter
overflow handling for messages larger than 1 MByte.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 781a08d9740a ("crypto: atmel-aes - Fix counter overflow in CTR mode") Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
HPAGE_SHIFT is only defined on architectures that support hugepages:
drivers/infiniband/core/umem_odp.c: In function 'ib_umem_odp_get':
drivers/infiniband/core/umem_odp.c:245:26: error: 'HPAGE_SHIFT' undeclared (first use in this function); did you mean 'PAGE_SHIFT'?
Enclose this in an #ifdef.
Fixes: 9ff1b6466a29 ("IB/core: Fix ODP with IB_ACCESS_HUGETLB handling") Link: https://lore.kernel.org/r/20200109084740.2872079-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The recent patch that substituted a flag on an rxrpc_call for the
connection pointer being NULL as an indication that a call was disconnected
puts the set_bit in the wrong place for service calls. This is only a
problem if a call is implicitly terminated by a new call coming in on the
same connection channel instead of a terminating ACK packet.
In such a case, rxrpc_input_implicit_end_call() calls
__rxrpc_disconnect_call(), which is now (incorrectly) setting the
disconnection bit, meaning that when rxrpc_release_call() is later called,
it doesn't call rxrpc_disconnect_call() and so the call isn't removed from
the peer's error distribution list and the list gets corrupted.
KASAN finds the issue as an access after release on a call, but the
position at which it occurs is confusing as it appears to be related to a
different call (the call site is where the latter call is being removed
from the error distribution list and either the next or pprev pointer
points to a previously released call).
Fix this by moving the setting of the flag from __rxrpc_disconnect_call()
to rxrpc_disconnect_call() in the same place that the connection pointer
was being cleared.
Fixes: 5273a191dca6 ("rxrpc: Fix NULL pointer deref due to call->conn being cleared on disconnect") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Avoid the "writable" check in __gfn_to_hva_many(), which will always fail
on read-only memslots due to gfn_to_hva() assuming writes. Functionally,
this allows x86 to create large mappings for read-only memslots that
are backed by HugeTLB mappings.
Note, the changelog for commit 05da45583de9 ("KVM: MMU: large page
support") states "If the largepage contains write-protected pages, a
large pte is not used.", but "write-protected" refers to pages that are
temporarily read-only, e.g. read-only memslots didn't even exist at the
time.
Fixes: 4d8b81abc47b ("KVM: introduce readonly memslot") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Redone using kvm_vcpu_gfn_to_memslot_prot. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case writing to vmread destination operand result in a #PF, vmread
should not call nested_vmx_succeed() to set rflags to specify success.
Similar to as done in VMPTRST (See handle_vmptrst()).
Reviewed-by: Liran Alon <liran.alon@oracle.com> Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: stable@vger.kernel.org Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a Spectre-v1/L1TF vulnerability in vmx_handle_exit().
While exit_reason is set by the hardware and therefore should not be
attacker-influenced, an unknown exit_reason could potentially be used to
perform such an attack.
Fixes: 55d2375e58a6 ("KVM: nVMX: Move nested code to dedicated files") Signed-off-by: Marios Pomonis <pomonis@google.com> Signed-off-by: Nick Finco <nifi@google.com> Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we have nested or circular eventfd wakeups, then we can deadlock if
we run them inline from our poll waitqueue wakeup handler. It's also
possible to have very long chains of notifications, to the extent where
we could risk blowing the stack.
Check the eventfd recursion count before calling eventfd_signal(). If
it's non-zero, then punt the signaling to async context. This is always
safe, as it takes us out-of-line in terms of stack and locking context.
If an application is using eventfd notifications with poll to know when
new SQEs can be issued, it's expecting the following read/writes to
complete inline. And with that, it knows that there are events available,
and don't want spurious wakeups on the eventfd for those requests.
This adds IORING_REGISTER_EVENTFD_ASYNC, which works just like
IORING_REGISTER_EVENTFD, except it only triggers notifications for events
that happen from async completions (IRQ, or io-wq worker completions).
Any completions inline from the submission itself will not trigger
notifications.
This patch is trying to address the issue observed when hotplug DP
daisy chain monitors.
e.g.
src-mstb-mstb-sst -> src (unplug) mstb-mstb-sst -> src-mstb-mstb-sst
(plug in again)
Once unplug a DP MST capable device, driver will call
drm_dp_mst_topology_mgr_set_mst() to disable MST. In this function,
it cleans data of topology manager while disabling mst_state. However,
it doesn't clean up the proposed_vcpis of topology manager.
If proposed_vcpi is not reset, once plug in MST daisy chain monitors
later, code will fail at checking port validation while trying to
allocate payloads.
When MST capable device is plugged in again and try to allocate
payloads by calling drm_dp_update_payload_part1(), this
function will iterate over all proposed virtual channels to see if
any proposed VCPI's num_slots is greater than 0. If any proposed
VCPI's num_slots is greater than 0 and the port which the
specific virtual channel directed to is not in the topology, code then
fails at the port validation. Since there are stale VCPI allocations
from the previous topology enablement in proposed_vcpi[], code will fail
at port validation and reurn EINVAL.
[How]
Clean up the data of stale proposed_vcpi[] and reset mgr->proposed_vcpis
to NULL while disabling mst in drm_dp_mst_topology_mgr_set_mst().
Changes since v1:
*Add on more details in commit message to describe the issue which the
patch is trying to fix
cgroup events are always installed in the cpuctx. However, when it is not
installed via IPI, list_update_cgroup_event() adds it to cpuctx of current
CPU, which triggers list corruption:
Decreasing sysctl_perf_event_mlock between two consecutive perf_mmap()s of
a perf ring buffer may lead to an integer underflow in locked memory
accounting. This may lead to the undesired behaviors, such as failures in
BPF map creation.
Address this by adjusting the accounting logic to take into account the
possibility that the amount of already locked memory may exceed the
current limit.
Fixes: c4b75479741c ("perf/core: Make the mlock accounting simple again") Suggested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: https://lkml.kernel.org/r/20200123181146.2238074-1-songliubraving@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel BUG at kernel/time/timer.c:1154!
BUG_ON(timer_pending(timer) || !timer->function) in add_timer_on().
At the same time another cpu got:
general protection fault: 0000 [#1] SMP PTI of poinson pointer 0xdead000000000200 in:
__hlist_del at include/linux/list.h:681
(inlined by) detach_timer at kernel/time/timer.c:818
(inlined by) expire_timers at kernel/time/timer.c:1355
(inlined by) __run_timers at kernel/time/timer.c:1686
(inlined by) run_timer_softirq at kernel/time/timer.c:1699
Unfortunately kernel logs are badly scrambled, stacktraces are lost.
Printing the timer->function before the BUG_ON() pointed to
clocksource_watchdog().
The execution of clocksource_watchdog() can race with a sequence of
clocksource_stop_watchdog() .. clocksource_start_watchdog():
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org> Debugged-by: Evan Green <evgreen@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Evan Green <evgreen@chromium.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mounting with -o modefromsid, the mode bits are stored in an
ACE. Directory enumeration (e.g. ls -l /mnt) triggers an SMB Query Dir
which does not include ACEs in its response. The mode bits in this
case are silently set to a default value of 755 instead.
This patch marks the dentry created during the directory enumeration
as needing re-evaluation (i.e. additional Query Info with ACEs) so
that the mode bits can be properly extracted.
Quick repro:
$ mount.cifs //win19.test/data /mnt -o ...,modefromsid
$ touch /mnt/foo && chmod 751 /mnt/foo
$ stat /mnt/foo
# reports 751 (OK)
$ sleep 2
# dentry older than 1s by default get invalidated
$ ls -l /mnt
# since dentry invalid, ls does a Query Dir
# and reports foo as 755 (WRONG)
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have a soft mount we should fail commands for session-setup
failures (such as the password having changed/ account being deleted/ ...)
and return an error back to the application.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c93d ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events") Fixes: fd9b4be8002c ("net/mlx5e: RX, Support multiple outstanding UMR posts") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d365498 ("r8169: remove fiddling with the PCIe max read request size") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop monitor uses a work item that takes care of constructing and
sending netlink notifications to user space. In case drop monitor never
started to monitor, then the work item is uninitialized and not
associated with a function.
Therefore, a stop command from user space results in canceling an
uninitialized work item which leads to the following warning [1].
Fix this by not processing a stop command if drop monitor is not
currently monitoring.
commit cedeac9df4b8 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4b8 ("qed: Add support for Timestamping the unicast PTP packets.") Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__in6_dev_get(dev) called from inet6_set_link_af() can return NULL.
The needed check has been recently removed, let's add it back.
While do_setlink() does call validate_linkmsg() :
...
err = validate_linkmsg(dev, tb); /* OK at this point */
...
It is possible that the following call happening before the
->set_link_af() removes IPv6 if MTU is less than 1280 :
if (tb[IFLA_MTU]) {
err = dev_set_mtu_ext(dev, nla_get_u32(tb[IFLA_MTU]), extack);
if (err < 0)
goto errout;
status |= DO_SETLINK_MODIFIED;
}
...
if (tb[IFLA_AF_SPEC]) {
...
err = af_ops->set_link_af(dev, af);
->inet6_set_link_af() // CRASH because idev is NULL
Please note that IPv4 is immune to the bug since inet_set_link_af() does :
struct in_device *in_dev = __in_dev_get_rcu(dev);
if (!in_dev)
return -EAFNOSUPPORT;
This problem has been mentioned in commit cf7afbfeb8ce ("rtnl: make
link af-specific updates atomic") changelog :
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
During enqueue, it works out that the verification added for the
"txtime" assisted mode is run when using taprio + ETF offloading, the
only thing missing is initializing the 'next_txtime' of all the cycle
entries. (if we don't set 'next_txtime' all packets from SO_TXTIME
sockets are dropped)
Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When destroying the current taprio instance, which can happen when the
creation of one fails, we should reset the traffic class configuration
back to the default state.
netdev_reset_tc() is a better way because in addition to setting the
number of traffic classes to zero, it also resets the priority to
traffic classes mapping to the default value.
Fixes: 5a781ccbd19e ("tc: Add support for configuring the taprio scheduler") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netlink policy validation for the 'flags' argument was missing.
Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because 'q->flags' starts as zero, and zero is a valid value, we
aren't able to detect the transition from zero to something else
during "runtime".
The solution is to initialize 'q->flags' with an invalid value, so we
can detect if 'q->flags' was set by the user or not.
To better solidify the behavior, 'flags' handling is moved to a
separate function. The behavior is:
- 'flags' if unspecified by the user, is assumed to be zero;
- 'flags' cannot change during "runtime" (i.e. a change() request
cannot modify it);
With this new function we can remove taprio_flags, which should reduce
the risk of future accidents.
Allowing flags to be changed was causing the following RCU stall:
Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver implementing taprio offloading depends on the value of
the network device number of traffic classes (dev->num_tc) for
whatever reason, it was going to receive the value zero. The value was
only set after the offloading function is called.
So, moving setting the number of traffic classes to before the
offloading function is called fixes this issue. This is safe because
this only happens when taprio is instantiated (we don't allow this
configuration to be changed without first removing taprio).
Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading") Reported-by: Po Liu <po.liu@nxp.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c8783330 ("net: stmmac: implement support for passive mode converters via dt") Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Tested-by: Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f07a ("net: stmmac: xgmac: Fix XGMAC selftests") Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support") Signed-off-by: Verma, Aashish <aashishx.verma@intel.com> Tested-by: Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log