Magnus Kroken [Thu, 16 Apr 2020 15:47:47 +0000 (17:47 +0200)]
mbedtls: update to 2.16.6
Security fixes for:
* CVE-2020-10932
* a potentially remotely exploitable buffer overread in a DTLS client
* bug in DTLS handling of new associations with the same parameters
Full release announement:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.16.6-and-2.7.15-released
Daniel Golle [Fri, 17 Apr 2020 12:11:11 +0000 (13:11 +0100)]
mac80211: make sure existing iface belongs to correct (fullmac) phy
Some FullMAC cfg80211 wireless devices do not support virtual
interfaces, hence there is script logic to keep the existing network
device. Improve this to support renaming the interface if needed and
make sure the existing interface actually belongs to the right phy.
Change calls to 'iw' to avoid outputing warnings and errors to not
confuse users of such devices.
Also bump PKG_RELEASE which has been forgotten in the previous two
mac80211 changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Tue, 14 Apr 2020 21:21:19 +0000 (23:21 +0200)]
uboot-imx6: bump to 2020.04 release
Refreshed all patches, run tested on apalis.
Cc: Vladimir Vid <vladimir.vid@sartura.hr> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Thu, 16 Apr 2020 19:30:27 +0000 (21:30 +0200)]
mac80211: drop data frames without key on encrypted links
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 12 Apr 2020 11:33:01 +0000 (13:33 +0200)]
ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E
SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (correct MAC)
- 5 GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
David Bauer [Sun, 12 Apr 2020 11:03:31 +0000 (13:03 +0200)]
ath79: add QCA9550 reset sequence
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.
Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.
This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.
ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnD
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ramips: mt7621: enable lzma-loader for some devices
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.
Paul Spooren [Mon, 6 Apr 2020 11:53:19 +0000 (01:53 -1000)]
scripts/download: add sources CDN as first mirror
OpenWrt now has a CDN for sources at sources.cdn.openwrt.org which
mirrors sources.openwrt.org.
Downloading sources outside Europe or US (mainland) could
result in low throughput, extremely slowing down the first compilation of
the build system.
This patch adds sources.cdn.openwrt.org as the first mirror to offer
worldwide fast download speeds by default. If the CDN goes down for
whatever reason, the script jumps to the next available mirror and
downloads requested files as before (in regional varying speed).
Signed-off-by: Paul Spooren <mail@aparcar.org> Acked-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Paul Spooren [Wed, 8 Apr 2020 20:17:01 +0000 (10:17 -1000)]
scripts: JSON merge don't crash if no JSON found
The JSON `WORK_DIR` ($(KDIR)/json_info_files) is only created if the new
image generation methods from `image.mk` are used. However some targets
like `armvirt` do not use it yet, so the folder is never created.
The `json_overview_image_info.py` script used to raise an error if the
given `WORK_DIR` isn't a folder, however it should just notify about
missing JSON files.
This patch removes the Python assert and exists with code 0 even if no
JSON files were found, as this is not necessarily an error but simply
not yet implemented. Using `glob` on an not existing `Path` results in
an empty list, therefore the for loop won't run.
Signed-off-by: Paul Spooren <mail@aparcar.org> CC: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Tue, 14 Apr 2020 15:11:05 +0000 (16:11 +0100)]
procd: jail fixes and improvements
32c717e jail: only mess with rootfs if CLONE_NEWNS was set b275a62 instance: harmonize instance API 511fd97 jail: make /proc more secure 4953b7c jail: mount /sys read-only a4d6442 jail: replace /etc/resolv.conf with symlink in extroot+overlay a4cc165 jail: always mount /dev as additional tmpfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Wed, 8 Apr 2020 12:43:04 +0000 (14:43 +0200)]
ath79: further fixes for ZyXEL NBG6716
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):
- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED
This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips: define image recipe for uncompressed uimage with loader
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.
Luiz Angelo Daros de Luca [Tue, 11 Feb 2020 19:25:36 +0000 (16:25 -0300)]
ath79: add read support using spi-mem
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.
It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.
It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Alberto Bursi [Fri, 10 Apr 2020 20:45:19 +0000 (22:45 +0200)]
x86: add nforce eth to default packages
forcedeth is necessary to use the integrated
ethernet controller of Nvidia nForce chipset.
There are PC motherboards with this chipset
from 2001 that run 32bit Athlon XP CPUs and
more modern ones up to 2009 that can run Intel
and AMD 64bit processors, so add this to
all non-geode x86 targets.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Tomasz Maciej Nowak [Thu, 12 Mar 2020 18:03:34 +0000 (19:03 +0100)]
mvebu: drop armada-37xx PCI aardvark patches
These patches were necessarry for Atheros and some Intel WiFi cards.
After short testing, the current upstream driver state is enough for
these WiFi cards to work. If there are still some issues with other
devices, the patches could be easily restored.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Flash instruction (UART+TFTP):
1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
2. Remove any hard drive from inside the bays.
3. Boot the Openwrt initramfs image using the U-Boot serial console:
tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
bootm 0x1200000
4. Flash the sysupgrade image using the Openwrt console:
sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
5. Wait until it finish, the device will reboot with Openwrt installed
on the NAND flash.
Note:
- Device shuting down doesn't work, even if the power slide switch is
used. We must first, via MDIO, set the unused LED2 at the ethernet
phy0 to off state. Reboot works ok.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Modified patch 005 to build more stuff. It was failing before. It still
only builds libraries.
Modified patch 100 to use strerror under non-glibc. It is used under
glibc as strerror is not thread safe. It is under musl and uClibc-ng.
strerror_l is not available under uClibc-ng.
Guillaume Lefebvre [Fri, 20 Dec 2019 23:21:32 +0000 (00:21 +0100)]
ath79: fix wmac initialization for Zyxel NBG6716
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.
Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5
This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Sun, 12 Apr 2020 19:28:49 +0000 (20:28 +0100)]
base-files: don't ship local build key when on buildbot
Including the local build key in /etc/opkg/keys isn't feasible when
building on the buildbot: The included key collides with its copy
already in openwrt-keyring which breaks the ImageBuilder.
Not including a locally generated key also makes the base-files package
more reproducible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
ramips: explicitly disable built-in switch when needed
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.
base-files: preinit: also config switch when no port roles defined
current preinit code in base-files doesn't config switch when there are
no port roles defined. But this kind of configuration exists on single
port devices where switch vlan is simply disabled.
configure reset and enable_vlan property when a switch node exist.
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.
ramips: port 0034-NET-multi-phy-support.patch to 5.4
This hack is needed for old ethernet driver:
On mt7620, we have two exposed RGMII ports that connects to builtin
switch. However, swconfig has no way to interact with phy subsystem.
As a result, we have to register both PHYs to ethernet mac instead
and this patch prevents main ethernet interface from going down due
to phy link changes.
Also rename the patch for its actual purpose.
increase spi frequency for both devices to 45MHz.
while at it, also remove m25p,fast-read for newifi d1 as it's only
needed when spi clock is higher than 50MHz.
Instead of resetting flash to 3B address on remove hook, this
implementation only enters 4B mode when needed, which prevents more
unexpected reboot stuck. This implementation makes it only break when
a kernel panic happens during flash operation on 16M+ areas.
Also silent broken-flash-reset warning. We are not dealing with vendors
and it's unpleasant for users to see that unnecessary and long WARN_ON
print.
Adrian Schmutzler [Fri, 13 Mar 2020 15:05:43 +0000 (16:05 +0100)]
base-files: do not source system.sh in functions.sh
The default_postinst() function in /lib/functions.sh sources
/lib/functions/system.sh before cycling through uci-defaults files.
This creates a pseudo-cyclic dependency as system.sh also uses
functions that are located in functions.sh. Despite that, there
is actually only one uci-defaults file in the entire repo that needs
system.sh, and this one contains an explicit source for system.sh
anyway.
Consequently, this patch removes the sourcing of system.sh in
functions.sh. There are no relevant uses in packages, routing and
luci repositories.
This may require adjustments for downstream, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 1 Apr 2020 22:29:21 +0000 (00:29 +0200)]
cns3xx: remove support for kernel 4.14
This target has been on kernel 4.19 for nine months now [1], and
has had testing support for even longer [2].
This should be long enough to drop support for kernel 4.14.
[1] 545bfbc3a922 ("cns3xxx: switch to kernel 4.19")
[2] c6bebe1a9496 ("cns3xxx: add support for kernel 4.19")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 7 Apr 2020 08:47:18 +0000 (10:47 +0200)]
ramips: mt7621: tidy up names for Ubiquiti devices
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.
This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.
While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Apr 2020 18:53:56 +0000 (20:53 +0200)]
bcm63xx: 5.4: fix compilation for changed driver_find_device
In kernel patch 92ce7e83b4e5 ("driver_find_device: Unify the match
function with class_find_device()") the arguments of functions used
with driver_find_device are adjusted. Do the same for our local
user.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The helper syscon_regmap_lookup_by_pdevname has been removed in kernel patch 29d14b668d2f ("mfd: Remove unused helper syscon_regmap_lookup_by_pdevname")
due to lack of users.
However, we use this function in our local pinctrl drivers for BCM6358 and
BCM6368. Thus, we have to add it locally.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Apr 2020 15:48:43 +0000 (17:48 +0200)]
bcm63xx: prevent fall-through in kernel patches for 5.4
In kernel 5.4 -Werror=implicit-fallthrough is treated as error:
arch/mips/bcm63xx/cpu.c: In function 'detect_cpu_clock':
arch/mips/bcm63xx/cpu.c:158:2: error: this statement may fall through [-Werror=implicit-fallthrough=]
{
^
arch/mips/bcm63xx/cpu.c:179:2: note: here
case BCM6328_CPU_ID:
^~~~
cc1: all warnings being treated as errors
This can be fixed by adding "Fall through" as a comment where intended,
and has to be fixed by returning a proper default otherwise.
In case of the default clock frequency for BCM6318 we fixed this by
returning the default value taken from BCM6328 and BCM6362.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Apr 2020 15:16:35 +0000 (17:16 +0200)]
broadcom-wl: fix compilation with kernel 5.4
This adds two fixes for compilation with kernel 5.4:
1. dev_open from include/linux/netdevice.h needs a second parameter
since kernel 5.0: 00f54e68924e ("net: core: dev: Add extack argument to dev_open()")
2. get_ds() macro definition has been dropped since kernel 5.1: 736706bee329 ("get rid of legacy 'get_ds()' function")
Since get_ds() has been just a macro before, replace it in
the driver instead of creating a version switch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Apr 2020 14:41:02 +0000 (16:41 +0200)]
bcm63xx: fix missing watchdog core dependency
This patch follows the other patches that added the watchdog
core to various (armvirt, malta, ath79, ...) targets that
have been hit by the following build error:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
In theory, we could have just added the CONFIG_WATCHDOG_CORE=y
to the Kconfig variable of kmod-hwmon-sch5627's package definition.
This would have forced the watchdog core to be builtin and less
architectures would need to be updated. But we might as well follow
through here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 2 Apr 2020 17:52:00 +0000 (19:52 +0200)]
broadcom-wl: fix compilation with kernel >= 4.15
Since kernel 4.15, init_timer is not available anymore, and has been
replaced by timer_setup. The fixes compilation of wl_linuc.c, which
returned the following errors beforehand (line-wrapped manually):
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c: In function 'wl_init_timer':
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2576:2: error: implicit
declaration of function 'init_timer'; did you mean 'init_timers'?
[-Werror=implicit-function-declaration]
init_timer(&t->timer);
^~~~~~~~~~
init_timers
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2577:10: error:
'struct timer_list' has no member named 'data'
t->timer.data = (ulong) t;
^
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2578:20: error: assignment
to 'void (*)(struct timer_list *)' from incompatible pointer type
'void (*)(ulong)' {aka 'void (*)(long unsigned int)'}
[-Werror=incompatible-pointer-types]
t->timer.function = wl_timer;
This should fix build of several devices on bcm63xx with testing
kernel (4.19).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kconfig update requires further testing and refinement until it can
remain in tree. Main problems are:
- Recursive deps are now fatal instead of a warning
- Previously legal syntax now leads to hard failures
- It fails all package builds since multiple days
The updated kconfig implementation needs to cope with the current status
quo in the various package feeds before we can reconsider it for master.
It is not desirable that single broken packages can hard-fail the entire
build pipeline.
Reverting this commit in preparation for reverting dcf3e63a35 ("build: scripts/config - update to kconfig-v5.6") which
introduces various unaddressed build breakages.
Reverting this commit in preparation for reverting dcf3e63a35 ("build: scripts/config - update to kconfig-v5.6") which
introduces various unaddressed build breakages.
Jo-Philipp Wich [Tue, 31 Mar 2020 07:54:58 +0000 (09:54 +0200)]
generic: drop 616-net_optimize_xfrm_calls.patch
The conditional check introduced by this patch may trigger a NULL pointer
dereference in case the result of dev_net() is NULL.
Since the purpose of this patch is neither sufficiently explained and since
this patch apparently has never been submitted upstream despite it being in
the pending-* patch directory, I propose to drop it without replacement.
If the performance implications of dropping this patch are found to be
significiant, it should be reintroduced with proper description and
benchmark results.
Eneas U de Queiroz [Fri, 10 Apr 2020 00:39:17 +0000 (21:39 -0300)]
build: config: allow bool to select a module pkg
kconfig-v5.6 disallowed a bool symbol to select another symbol that
'depends on m' (i.e. can be only 'm' on 'n'). It is, in fact, an unmet
dependency to have set to 'y'. However, openwrt depends on the previous
behavior, to be able to build a package that can be a module or built-in
depending on a bool config. This restores the previous behavior.
Ref: https://forum.openwrt.org/t/wireless-fails-on-snapshot-r12900-kernel-5-4-on-c2600-ipq806x Tested-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> [added forum ref]
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
projects / users / dwmw2 / openwrt.git / log