Commit: 5075a47f3765e778b45367ba4873c1bd08b21d0e
fix-up code base for v4.1.12-46 merge
should not have removed "#include <linux/hugetlb.h>"
Add it back in after applying adfc71b605:
fix-up - add back include of linux/dtrace_os.h
so that it will merge with master.
Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com>
Commit: bd52d0fd57c96146f8d1838588753ab9dabcd2fe:
sparc64: Log warning for invalid hugepages boot param
removes "#include <linux/dtrace_os.h>" from arch/sparc/mm/fault_64.c.
That header file is needed by dtrace. Add it back in.
Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com>
Bang Nguyen [Sat, 16 Apr 2016 18:47:05 +0000 (11:47 -0700)]
RDS: Fix the rds_conn_destroy panic due to pending messages
In corner cases, there could be pending messages on connection which
needs to be detsroyed. Make sure those messages are purged before
the connection is torned down.
RDS: add handshaking for ACL violation detection at passive
Offending connections with ACL violations should be cleaned up as
early as possible. When active detects ACL violation and sends reject;
it fills up private_data field. Passive checks for private_data
whenever it receives reject; and in case of ACL violation it destroys
connection.
Santosh Shilimkar [Tue, 15 Mar 2016 12:32:09 +0000 (05:32 -0700)]
RDS: IB: enforce IP anti-spoofing for UUID context
Connection is established only after the IP requesting the connection
is legitimate and part of the ACL group. Invalid connection request(s)
are rejected and destroyed.
Ajay moved destroy connection when ACL check fails while initiating
connection to avoid unnecessary packet transfer on wire.
This is to avoid deadlock with c_cm_lock mutex.
In event handling path of Infiniband, whenever connection destruction is
required; we should invoke worker in order to avoid deadlock with mutex.
Knut Omang [Wed, 25 May 2016 09:01:10 +0000 (11:01 +0200)]
sif driver initial commit part 1
sif_ah.c: Implementation of IB address handles for SIF
sif_ah.h: Interface to internal IB address handle logic for SIF
sif_base.c: Basic hardware setup of SIF
sif_base.h: Basic hardware setup of SIF
sif_checksum.c: Utilities for SIF specific 32 bit checksums
sif_checksum.h: Utilities for SIF specific 32 bit checksums
sif_cq.c: Implementation of completion queue logic for SIF
sif_cq.h: Internal interface to psif completion queue logic
sif_debug.c: Use of debugfs for dumping internal data structure info
sif_debug.h: Use of debugfs for dumping internal data structure info
sif_defs.c: IB-to-SIF Mapper.
sif_defs.h: Div. utility definitions and auxiliary data structures
sif_dev.h: Driver specific data structure definitions
sif_dma.c: DMA memory mapping
sif_dma.h: DMA memory mapping
sif_drvapi.h: Device specific operations available via the FWA access path
sif_elog.c: Log over PCIe support for firmware
sif_elog.h: Misc device for capturing log from the EPSC
sif_enl.h: Protocol definitions for the netlink protocol for EPSC access from
sif_epsc.c: Implementation of API for communication with the EPSC
sif_epsc.h: API for communication with the EPSC (and EPS-A's)
sif_eq.c: Setup of event queues and interrupt handling
sif_eq.h: Event queues and interrupt handling
sif_fmr.c: Implementation of fast memory registration for SIF
sif_fmr.h: Interface to internal IB Fast Memory Registration (FMR)
Credits:
The sif driver supports Oracle’s new Dual Port EDR and QDR
IB Adapters and the integrated IB devices on the new SPARC SoC.
The driver is placed under drivers/infiniband/hw/sif
This patch set is the result of direct or indirect contribution by
several people:
Code contributors:
Knut Omang, Vinay Shaw, Haakon Bugge, Wei Lin Guay,
Lars Paul Huse, Francisco Trivino-Garcia.
Minor patch/bug fix contributors:
Hans Westgaard Ry, Jesus Escudero, Robert Schmidt, Dag Moxnes,
Andre Wuttke, Predrag Hodoba, Roy Arntsen
Initial architecture adaptations:
Khalid Aziz (sparc64), Gerd Rausch (arm64)
Testing, Test development, Continuous integration, Bug haunting, Code
review:
Knut Omang, Hakon Bugge, Åsmund Østvold, Francisco Trivino-Garcia,
Wei Lin Guay, Vinay Shaw, Hans Westgaard Ry,
+ numerous other people within Oracle.
Simulator development:
Andrew Manison, Hans Westgaard Ry, Knut Omang, Vinay Shaw
Wei Lin Guay [Tue, 24 May 2016 07:37:22 +0000 (09:37 +0200)]
sif driver initial commit part 4
sif_tqp.h: Implementation of EPSA tunnelling QP for SIF
sif_user.h: This file defines sif specific verbs extension request/response.
sif_verbs.c: IB verbs API extensions specific to PSIF
sif_verbs.h: IB verbs API extensions specific to PSIF
sif_vf.c: SR/IOV support functions
sif_vf.h: SR/IOV support functions
sif_xmmu.c: Implementation of special MMU mappings.
sif_xmmu.h: Implementation of special MMU mappings.
sif_xrc.c: Implementation of XRC related functions
sif_xrc.h: XRC related functions
version.h: Detailed version info data structure
Knut Omang [Wed, 25 May 2016 09:01:11 +0000 (11:01 +0200)]
sif driver initial commit part 3
sif_pt.c: SIF (private) page table management
sif_pt.h: SIF (private) page table management.
sif_qp.c: Implementation of IB queue pair logic for sif
sif_qp.h: Interface to internal IB queue pair logic for sif
sif_query.c: SIF implementation of some of IB query APIs
sif_query.h: SIF implementation of some of IB query APIs
sif_r3.c: Special handling specific for psif revision 3 and earlier
sif_r3.h: Special handling specific for psif revision 3 and earlier
sif_rq.c: Implementation of sif receive queues
sif_rq.h: Interface to sif receive queues
sif_sndrcv.c: Implementation of post send/recv logic for SIF
sif_sndrcv.h: Interface to IB send/receive, MAD packet recv and
sif_spt.c: Experimental implementation of shared use of the OS's page tables.
sif_spt.h: Experimental (still unsafe)
sif_sq.c: Implementation of the send queue side of an IB queue pair
sif_sq.h: Implementation of the send queue side of an IB queue pair
sif_srq.c: Interface to shared receive queues for SIF
sif_srq.h: Interface to internal Shared receive queue logic for SIF
sif_tqp.c: Implementation of EPSA tunneling QP for SIF
Knut Omang [Wed, 25 May 2016 09:01:11 +0000 (11:01 +0200)]
sif driver initial commit part 2
sif_fwa.c: Firmware access API (netlink based out-of-band comm)
sif_fwa.h: Low level access to a SIF device
sif_hwi.c: Hardware init for SIF - combines the various init steps for psif
sif_hwi.h: Hardware init for SIF
sif_ibcq.h: External interface to IB completion queue logic for SIF
sif_ibpd.h: External interface to (IB) protection domains for SIF
sif_ibqp.h: External interface to IB queue pair logic for sif
sif_idr.c: Synchronized ID ref allocation
sif_idr.h: simple id allocation and deallocation for SIF
sif_int_user.h: This file defines special internal data structures used
sif_ireg.c: Utilities and entry points needed for Infiniband registration
sif_ireg.h: support functions used in setup of sif as an IB HCA
sif_main.c: main entry points and initialization
sif_mem.c: SIF table memory and page table management
sif_mem.h: A common interface for all memory used by
sif_mmu.c: main entry points and initialization
sif_mmu.h: API for management of sif's on-chip mmu.
sif_mr.c: Implementation of memory regions support for SIF
sif_mr.h: Interface to internal IB memory registration logic for SIF
sif_mw.c: Implementation of memory windows for SIF
sif_mw.h: Interface to internal IB memory window logic for SIF
sif_pd.c: Implementation of IB protection domains for SIF
sif_pd.h: Internal interface to protection domains
sif_pqp.c: Privileged QP handling
sif_pqp.h: Privileged QP handling
Hannes Reinecke [Thu, 26 Nov 2015 07:46:57 +0000 (08:46 +0100)]
block: Always check queue limits for cloned requests
When a cloned request is retried on other queues it always needs
to be checked against the queue limits of that queue.
Otherwise the calculations for nr_phys_segments might be wrong,
leading to a crash in scsi_init_sgtable().
To clarify this the patch renames blk_rq_check_limits()
to blk_cloned_rq_check_limits() and removes the symbol
export, as the new function should only be used for
cloned requests and never exported.
Cc: Mike Snitzer <snitzer@redhat.com> Cc: Ewan Milne <emilne@redhat.com> Cc: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Fixes: e2a60da74 ("block: Clean up special command handling logic") Cc: stable@vger.kernel.org # 3.7+ Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
(cherry picked from commit bf4e6b4e757488dee1b6a581f49c7ac34cd217f8)
Orabug: 23140620 Signed-off-by: Jason Luo <zhangqing.luo@oracle.com>
Reported-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com> Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com> Signed-off-by: Allen Pais <allen.pais@oracle.com>
Add support for ACL tables for ib_ipoib and ib_cm drivers.
ib_cm driver exposes functions register and unregister tables and to manage
tables content.
In ib_ipoib driver add ACL object for each network device.
Santosh Shilimkar [Wed, 10 Feb 2016 18:49:16 +0000 (10:49 -0800)]
RDS: Drop stale iWARP support
RDS iWARP support was more of academic and was never complete neither
fully functional. Its getting for good. Thanks to Ajay for adding
couple of missed hunks.
Tested-by: Michael Nowak <michael.nowak@oracle.com> Tested-by: Rose Wang <rose.wang@oracle.com> Tested-by: Rafael Alejandro Peralez <rafael.peralez@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Santosh Shilimkar [Wed, 17 Feb 2016 18:10:14 +0000 (10:10 -0800)]
RDS: IB: drop discontinued IB CQ_VECTOR support
IB_CQ_VECTOR_LEAST_ATTACHED was OFED 1.5 feature which later Mellanox
dropped. As per them 'least attached' was not a way to distribute the load
and that actually fools the user to think it does so. The fact that some
cpu had 'least amount of attached cqs' has nothing to do with this cpu
actual load. This is why the feature never made to upstream.
On UEK4, the code is already under #if 0 because feature isn't
available. Time to clean up the dead code considering its already
dropped from upstream as well as OFED2.0+ onwards.
Tested-by: Michael Nowak <michael.nowak@oracle.com> Tested-by: Rose Wang <rose.wang@oracle.com> Tested-by: Rafael Alejandro Peralez <rafael.peralez@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Santosh Shilimkar [Wed, 10 Feb 2016 17:08:43 +0000 (09:08 -0800)]
RDS: IB: Drop unused and broken APM support
APM support in RDS has been broken and hence not being
used in production. We kept the code around but its time
to remove it and reduce the complexity in the RDS
failover code paths.
Tested-by: Michael Nowak <michael.nowak@oracle.com> Tested-by: Rose Wang <rose.wang@oracle.com> Tested-by: Rafael Alejandro Peralez <rafael.peralez@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
RDS active bonding gratuitous arp code needs to adopt to this change
to take advantage of the neighbor updates on UEK4. The current code
makes use ARPOP_REPLY which needs to be changed to ARPOP_REQUEST.
RDS: IB: don't use the link-local address for ib transport
Link-local address can't be used for IB failover and don't work
with IB stack. Even though the DB RDS usage has recommnded to not
use these addresses, we keep hitting issue because of accidental
usage of it because of missing application config or admin scripts
blindly doing rds-ping for each local address(s).
RDS TCP which doesn't support acitive active, there might be an
usecase so the current fix it limited for IB transport atm.
cosnole:
RDS/IB: Link local address 169.254.221.37 NOT SUPPORTED
RDS: rds_bind() could not find a transport for 169.254.221.37, load rds_tcp or rds_rdma?
Santosh Shilimkar [Wed, 18 May 2016 17:44:56 +0000 (10:44 -0700)]
RDS: IB: rebuild receive caches when needed
RDS IB caches code leaks memory & it have been there from the
inception of cache code but we didn't noticed them since caches
are not teardown in normal operation paths. But now to support
features like variable fragment or connection destroy for ACL,
caches needs to be destroyed and rebuild if needed.
While freeing the caches is just fine, leaking memory while
doing that is bug and needs to be addressed. Thanks to Wengang
for spotting this stone age leak. Also the cache rebuild needs
to be done only when desired so patch optimises that part as
well.
Tested-by: Michael Nowak <michael.nowak@oracle.com> Tested-by: Maria Rodriguez <maria.r.rodriguez@oracle.com> Tested-by: Hong Liu <hong.x.liu@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Backport of 81ad4276b505e987dd8ebbdf63605f92cd172b52 failed to adjust
for intervening ->get_trip_temp() argument type change, thus causing
stack protector to panic.
drivers/thermal/thermal_core.c: In function ‘thermal_zone_device_register’:
drivers/thermal/thermal_core.c:1569:41: warning: passing argument 3 of
‘tz->ops->get_trip_temp’ from incompatible pointer type [-Wincompatible-pointer-types]
if (tz->ops->get_trip_temp(tz, count, &trip_temp))
^
drivers/thermal/thermal_core.c:1569:41: note: expected ‘long unsigned int *’
but argument is of type ‘int *’
CC: <stable@vger.kernel.org> #3.18,#4.1 Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit 5640c4c37eee293451388cd5ee74dfed3a30f32d)
Tracking idle time in bictcp_cwnd_event() is imprecise, as epoch_start
is normally set at ACK processing time, not at send time.
Doing a proper fix would need to add an additional state variable,
and does not seem worth the trouble, given CUBIC bug has been there
forever before Jana noticed it.
Let's simply not set epoch_start in the future, otherwise
bictcp_update() could overflow and CUBIC would again
grow cwnd too fast.
This was detected thanks to a packetdrill test Neal wrote that was flaky
before applying this fix.
Fixes: 30927520dbae ("tcp_cubic: better follow cubic curve after idle period") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Cc: Jana Iyengar <jri@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit af05df01c7a9f4b3cf3dc29365f4c7c4e2cd53ff)
The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.
I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.
The following lockup was detected while testing the otg state
machine.
[ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.245358] usb usb1: Product: xHCI Host Controller
[ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 178.267014] hub 1-0:1.0: USB hub found
[ 178.272108] hub 1-0:1.0: 1 port detected
[ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.308776] usb usb2: Product: xHCI Host Controller
[ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 178.329061] hub 2-0:1.0: USB hub found
[ 178.333126] hub 2-0:1.0: 1 port detected
[ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 178.578064] usb usb2: USB disconnect, device number 1
[ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 178.597924] usb usb1: USB disconnect, device number 1
[ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000
[ 190.625120] Workqueue: usb_otg usb_otg_work
[ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.739898] 5 locks held by kworker/u4:0/6:
[ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000
[ 190.814457] Workqueue: usb_hub_wq hub_event
[ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.902650] 5 locks held by kworker/1:0/14:
[ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Starting with 4.1 the tracing subsystem has its own filesystem
which is automounted in the tracing subdirectory of debugfs.
Prior to this debugfs could be bind mounted in a cloned mount
namespace, but if tracefs has been mounted under debugfs this
now fails because there is a locked child mount. This creates
a regression for container software which bind mounts debugfs
to satisfy the assumption of some userspace software.
In other pseudo filesystems such as proc and sysfs we're already
creating mountpoints like this in such a way that no dirents can
be created in the directories, allowing them to be exceptions to
some MNT_LOCKED tests. In fact we're already do this for the
tracefs mountpoint in sysfs.
Do the same in debugfs_create_automount(), since the intention
here is clearly to create a mountpoint. This fixes the regression,
as locked child mounts on permanently empty directories do not
cause a bind mount to fail.
If we rename an inode A (be it a file or a directory), create a new
inode B with the old name of inode A and under the same parent directory,
fsync inode B and then power fail, at log tree replay time we end up
removing inode A completely. If inode A is a directory then all its files
are gone too.
Example scenarios where this happens:
This is reproducible with the following steps, taken from a couple of
test cases written for fstests which are going to be submitted upstream
soon:
The next time the fs is mounted, log tree replay happens and
the directory "y" does not exist nor do the files "foo" and
"bar" exist anywhere (neither in "y" nor in "x", nor the root
nor anywhere).
The next time the fs is mounted, log tree replay happens and the
file "bar" does not exists anymore. A file with the name "foo"
exists and it matches the second file we created.
Another related problem that does not involve file/data loss is when a
new inode is created with the name of a deleted snapshot and we fsync it:
The next time the fs is mounted the log replay procedure fails because
it attempts to delete the snapshot entry (which has dir item key type
of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry,
resulting in the following error that causes mount to fail:
Fix this by forcing a transaction commit when such cases happen.
This means we check in the commit root of the subvolume tree if there
was any other inode with the same reference when the inode we are
fsync'ing is a new inode (created in the current transaction).
Test cases for fstests, covering all the scenarios given above, were
submitted upstream for fstests:
* fstests: generic test for fsync after renaming directory
https://patchwork.kernel.org/patch/8694281/
* fstests: generic test for fsync after renaming file
https://patchwork.kernel.org/patch/8694301/
* fstests: add btrfs test for fsync after snapshot deletion
https://patchwork.kernel.org/patch/8670671/
Cc: stable@vger.kernel.org Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 033ad030df0ea932a21499582fea59e1df95769b)
When we have the no_holes feature enabled, if a we truncate a file to a
smaller size, truncate it again but to a size greater than or equals to
its original size and fsync it, the log tree will not have any information
about the hole covering the range [truncate_1_offset, new_file_size[.
Which means if the fsync log is replayed, the file will remain with the
state it had before both truncate operations.
Without the no_holes feature this does not happen, since when the inode
is logged (full sync flag is set) it will find in the fs/subvol tree a
leaf with a generation matching the current transaction id that has an
explicit extent item representing the hole.
Fix this by adding an explicit extent item representing a hole between
the last extent and the inode's i_size if we are doing a full sync.
The issue is easy to reproduce with the following test case for fstests:
_need_to_be_root
_supported_fs generic
_supported_os Linux
_require_scratch
_require_dm_flakey
# This test was motivated by an issue found in btrfs when the btrfs
# no-holes feature is enabled (introduced in kernel 3.14). So enable
# the feature if the fs being tested is btrfs.
if [ $FSTYP == "btrfs" ]; then
_require_btrfs_fs_feature "no_holes"
_require_btrfs_mkfs_feature "no-holes"
MKFS_OPTIONS="$MKFS_OPTIONS -O no-holes"
fi
# Now truncate our file foo to a smaller size (64Kb) and then truncate
# it to the size it had before the shrinking truncate (125Kb). Then
# fsync our file. If a power failure happens after the fsync, we expect
# our file to have a size of 125Kb, with the first 64Kb of data having
# the value 0xaa and the second 61Kb of data having the value 0x00.
$XFS_IO_PROG -c "truncate 64K" \
-c "truncate 125K" \
-c "fsync" \
$SCRATCH_MNT/foo
# Do something similar to our file bar, but the first truncation sets
# the file size to 0 and the second truncation expands the size to the
# double of what it was initially.
$XFS_IO_PROG -c "truncate 0" \
-c "truncate 253K" \
-c "fsync" \
$SCRATCH_MNT/bar
# Allow writes again, mount to trigger log replay and validate file
# contents.
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
# We expect foo to have a size of 125Kb, the first 64Kb of data all
# having the value 0xaa and the remaining 61Kb to be a hole (all bytes
# with value 0x00).
echo "File foo content after log replay:"
od -t x1 $SCRATCH_MNT/foo
# We expect bar to have a size of 253Kb and no extents (any byte read
# from bar has the value 0x00).
echo "File bar content after log replay:"
od -t x1 $SCRATCH_MNT/bar
status=0
exit
The expected file contents in the golden output are:
File foo content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0200000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 0372000
File bar content after log replay: 0000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 0772000
Without this fix, their contents are:
File foo content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0200000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
* 0372000
File bar content after log replay: 0000000 ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee
* 0200000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
* 0372000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 0772000
A test case submission for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 091537b5b3102af4765256d2b527a2a1de4fb184)
After commit 4f764e515361 ("Btrfs: remove deleted xattrs on fsync log
replay"), we can end up in a situation where during log replay we end up
deleting xattrs that were never deleted when their file was last fsynced.
This happens in the fast fsync path (flag BTRFS_INODE_NEEDS_FULL_SYNC is
not set in the inode) if the inode has the flag BTRFS_INODE_COPY_EVERYTHING
set, the xattr was added in a past transaction and the leaf where the
xattr is located was not updated (COWed or created) in the current
transaction. In this scenario the xattr item never ends up in the log
tree and therefore at log replay time, which makes the replay code delete
the xattr from the fs/subvol tree as it thinks that xattr was deleted
prior to the last fsync.
Fix this by always logging all xattrs, which is the simplest and most
reliable way to detect deleted xattrs and replay the deletes at log replay
time.
This issue is reproducible with the following test case for fstests:
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
here=`pwd`
tmp=/tmp/$$
status=1 # failure is the default!
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
. ./common/attr
# real QA test starts here
# We create a lot of xattrs for a single file. Only btrfs and xfs are currently
# able to store such a large mount of xattrs per file, other filesystems such
# as ext3/4 and f2fs for example, fail with ENOSPC even if we attempt to add
# less than 1000 xattrs with very small values.
_supported_fs btrfs xfs
_supported_os Linux
_need_to_be_root
_require_scratch
_require_dm_flakey
_require_attrs
_require_metadata_journaling $SCRATCH_DEV
# Create the test file with some initial data and make sure everything is
# durably persisted.
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0 32k" $SCRATCH_MNT/foo | _filter_xfs_io
sync
# Add many small xattrs to our file.
# We create such a large amount because it's needed to trigger the issue found
# in btrfs - we need to have an amount that causes the fs to have at least 3
# btree leafs with xattrs stored in them, and it must work on any leaf size
# (maximum leaf/node size is 64Kb).
num_xattrs=2000
for ((i = 1; i <= $num_xattrs; i++)); do
name="user.attr_$(printf "%04d" $i)"
$SETFATTR_PROG -n $name -v "val_$(printf "%04d" $i)" $SCRATCH_MNT/foo
done
# Sync the filesystem to force a commit of the current btrfs transaction, this
# is a necessary condition to trigger the bug on btrfs.
sync
# Now update our file's data and fsync the file.
# After a successful fsync, if the fsync log/journal is replayed we expect to
# see all the xattrs we added before with the same values (and the updated file
# data of course). Btrfs used to delete some of these xattrs when it replayed
# its fsync log/journal.
$XFS_IO_PROG -c "pwrite -S 0xbb 8K 16K" \
-c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Allow writes again and mount. This makes the fs replay its fsync log.
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
echo "File content after crash and log replay:"
od -t x1 $SCRATCH_MNT/foo
echo "File xattrs after crash and log replay:"
for ((i = 1; i <= $num_xattrs; i++)); do
name="user.attr_$(printf "%04d" $i)"
echo -n "$name="
$GETFATTR_PROG --absolute-names -n $name --only-values $SCRATCH_MNT/foo
echo
done
status=0
exit
The golden output expects all xattrs to be available, and with the correct
values, after the fsync log is replayed.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit db4043dffa5b9f77160dfba088bbbbaa64dd9ed1)
Changes since V1: fixed the description and added KASan warning.
In assoc_array_insert_into_terminal_node(), we call the
compare_object() method on all non-empty slots, even when they're
not leaves, passing a pointer to an unexpected structure to
compare_object(). Currently it causes an out-of-bound read access
in keyring_compare_object detected by KASan (see below). The issue
is easily reproduced with keyutils testsuite.
Only call compare_object() when the slot is a leave.
KASan warning:
==================================================================
BUG: KASAN: slab-out-of-bounds in keyring_compare_object+0x213/0x240 at addr ffff880060a6f838
Read of size 8 by task keyctl/1655
=============================================================================
BUG kmalloc-192 (Not tainted): kasan: bad access detected
-----------------------------------------------------------------------------
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org Fixes: 7bedd0cfad4e1 ("mac80211: use rhashtable for station table") Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit d2bccdc948e21a48d593181c05667d454f423fcd)
After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:
* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
dependency issues that arise with trying to remove the connector from
sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good
This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:
[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi
And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.
To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
With the internal Quota feature, mke2fs creates empty quota inodes and
quota usage tracking is enabled as soon as the file system is mounted.
Since quotacheck is no longer preallocating all of the blocks in the
quota inode that are likely needed to be written to, we are now seeing
a lockdep false positive caused by needing to allocate a quota block
from inside ext4_map_blocks(), while holding i_data_sem for a data
inode. This results in this complaint:
When unexpected situation happened (e.g. tx/rx irq happened while
DMAC is used), the usbhsf_pkt_handler() was possible to cause NULL
pointer dereference like the followings:
The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Daniel Fraga <fragabr@gmail.com> Tested-by: Daniel Fraga <fragabr@gmail.com> CC: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 8db1fb6a6e0fdc6f6fbfabfc4c9c5a183a7527ac)
Hanjun Guo has reported that a CMA stress test causes broken accounting of
CMA and free pages:
> Before the test, I got:
> -bash-4.3# cat /proc/meminfo | grep Cma
> CmaTotal: 204800 kB
> CmaFree: 195044 kB
>
>
> After running the test:
> -bash-4.3# cat /proc/meminfo | grep Cma
> CmaTotal: 204800 kB
> CmaFree: 6602584 kB
>
> So the freed CMA memory is more than total..
>
> Also the the MemFree is more than mem total:
>
> -bash-4.3# cat /proc/meminfo
> MemTotal: 16342016 kB
> MemFree: 22367268 kB
> MemAvailable: 22370528 kB
Laura Abbott has confirmed the issue and suspected the freepage accounting
rewrite around 3.18/4.0 by Joonsoo Kim. Joonsoo had a theory that this is
caused by unexpected merging between MIGRATE_ISOLATE and MIGRATE_CMA
pageblocks:
> CMA isolates MAX_ORDER aligned blocks, but, during the process,
> partialy isolated block exists. If MAX_ORDER is 11 and
> pageblock_order is 9, two pageblocks make up MAX_ORDER
> aligned block and I can think following scenario because pageblock
> (un)isolation would be done one by one.
>
> (each character means one pageblock. 'C', 'I' means MIGRATE_CMA,
> MIGRATE_ISOLATE, respectively.
>
> CC -> IC -> II (Isolation)
> II -> CI -> CC (Un-isolation)
>
> If some pages are freed at this intermediate state such as IC or CI,
> that page could be merged to the other page that is resident on
> different type of pageblock and it will cause wrong freepage count.
This was supposed to be prevented by CMA operating on MAX_ORDER blocks,
but since it doesn't hold the zone->lock between pageblocks, a race
window does exist.
It's also likely that unexpected merging can occur between
MIGRATE_ISOLATE and non-CMA pageblocks. This should be prevented in
__free_one_page() since commit 3c605096d315 ("mm/page_alloc: restrict
max order of merging on isolated pageblock"). However, we only check
the migratetype of the pageblock where buddy merging has been initiated,
not the migratetype of the buddy pageblock (or group of pageblocks)
which can be MIGRATE_ISOLATE.
Joonsoo has suggested checking for buddy migratetype as part of
page_is_buddy(), but that would add extra checks in allocator hotpath
and bloat-o-meter has shown significant code bloat (the function is
inline).
This patch reduces the bloat at some expense of more complicated code.
The buddy-merging while-loop in __free_one_page() is initially bounded
to pageblock_border and without any migratetype checks. The checks are
placed outside, bumping the max_order if merging is allowed, and
returning to the while-loop with a statement which can't be possibly
considered harmful.
This fixes the accounting bug and also removes the arguably weird state
in the original commit 3c605096d315 where buddies could be left
unmerged.
Fixes: 3c605096d315 ("mm/page_alloc: restrict max order of merging on isolated pageblock") Link: https://lkml.org/lkml/2016/3/2/280 Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Hanjun Guo <guohanjun@huawei.com> Tested-by: Hanjun Guo <guohanjun@huawei.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Debugged-by: Laura Abbott <labbott@redhat.com> Debugged-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> [3.18+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit da2041b6c4bf60904a7732eec0b20c89f54d9693)
__free_pages_bootmem prepares a page for release to the buddy allocator
and assumes that the struct page is initialised. Parallel initialisation
of struct pages defers initialisation and __free_pages_bootmem can be
called for struct pages that cannot yet map struct page to PFN. This
patch passes PFN to __free_pages_bootmem with no other functional change.
Signed-off-by: Mel Gorman <mgorman@suse.de> Tested-by: Nate Zimmer <nzimmer@sgi.com> Tested-by: Waiman Long <waiman.long@hp.com> Tested-by: Daniel J Blueman <daniel@numascale.com> Acked-by: Pekka Enberg <penberg@kernel.org> Cc: Robin Holt <robinmholt@gmail.com> Cc: Nate Zimmer <nzimmer@sgi.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Waiman Long <waiman.long@hp.com> Cc: Scott Norton <scott.norton@hp.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit bbd0b13f917860a686ccaf40cda003332a640a70)
When master handles convert request, it queues ast first and then
returns status. This may happen that the ast is sent before the request
status because the above two messages are sent by two threads. And
right after the ast is sent, if master down, it may trigger BUG in
dlm_move_lockres_to_recovery_list in the requested node because ast
handler moves it to grant list without clear lock->convert_pending. So
remove BUG_ON statement and check if the ast is processed in
dlmconvert_remote.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Reported-by: Yiwen Jiang <jiangyiwen@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Tariq Saeed <tariq.x.saeed@oracle.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 474b8c6d329cfc40680ef308878d22f5a1a3b02b)
There is a race window between dlmconvert_remote and
dlm_move_lockres_to_recovery_list, which will cause a lock with
OCFS2_LOCK_BUSY in grant list, thus system hangs.
status = dlm_send_remote_convert_request();
>>>>>> race window, master has queued ast and return DLM_NORMAL,
and then down before sending ast.
this node detects master down and calls
dlm_move_lockres_to_recovery_list, which will revert the
lock to grant list.
Then OCFS2_LOCK_BUSY won't be cleared as new master won't
send ast any more because it thinks already be authorized.
In this case, check if res->state has DLM_LOCK_RES_RECOVERING bit set
(res is still in recovering) or res master changed (new master has
finished recovery), reset the status to DLM_RECOVERING, then it will
retry convert.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Reported-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Tariq Saeed <tariq.x.saeed@oracle.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit d5865dc7deb118b1db82dcaf4d249668bc81a311)
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Fix deadlocking during concurrent receive and transmit operations on SMP
platforms caused by the use of incorrect lock: on transmit 'tx_lock'
spinlock should be used instead of 'lock' which is used for receive
operation.
This fix is applicable to kernel versions starting from v2.15.
Signed-off-by: Aurelien Jacquiot <a-jacquiot@ti.com> Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit e025091aa3a343703375c66e0bd02675b251411a)
This commit fixes the following security hole affecting systems where
all of the following conditions are fulfilled:
- The fs.suid_dumpable sysctl is set to 2.
- The kernel.core_pattern sysctl's value starts with "/". (Systems
where kernel.core_pattern starts with "|/" are not affected.)
- Unprivileged user namespace creation is permitted. (This is
true on Linux >=3.8, but some distributions disallow it by
default using a distro patch.)
Under these conditions, if a program executes under secure exec rules,
causing it to run with the SUID_DUMP_ROOT flag, then unshares its user
namespace, changes its root directory and crashes, the coredump will be
written using fsuid=0 and a path derived from kernel.core_pattern - but
this path is interpreted relative to the root directory of the process,
allowing the attacker to control where a coredump will be written with
root privileges.
To fix the security issue, always interpret core_pattern for dumps that
are written under SUID_DUMP_ROOT relative to the root directory of init.
Signed-off-by: Jann Horn <jann@thejh.net> Acked-by: Kees Cook <keescook@chromium.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Dan Duval <dan.duval@oracle.com>
(cherry picked from commit 2e840836fdf9ba0767134dcc5103dd25e442023b)
Moving the initialization earlier is needed in 4.6 because
kvm_arch_init_vm is now using mmu_lock, causing lockdep to
complain:
[ 284.440294] INFO: trying to register non-static key.
[ 284.445259] the code is fine but needs lockdep annotation.
[ 284.450736] turning off the locking correctness validator.
...
[ 284.528318] [<ffffffff810aecc3>] lock_acquire+0xd3/0x240
[ 284.533733] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.541467] [<ffffffff81715581>] _raw_spin_lock+0x41/0x80
[ 284.546960] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.554707] [<ffffffffa0305aa0>] kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.562281] [<ffffffffa02ece70>] kvm_mmu_init_vm+0x20/0x30 [kvm]
[ 284.568381] [<ffffffffa02dbf7a>] kvm_arch_init_vm+0x1ea/0x200 [kvm]
[ 284.574740] [<ffffffffa02bff3f>] kvm_dev_ioctl+0xbf/0x4d0 [kvm]
However, it also helps fixing a preexisting problem, which is why this
patch is also good for stable kernels: kvm_create_vm was incrementing
current->mm->mm_count but not decrementing it at the out_err label (in
case kvm_init_mmu_notifier failed). The new initialization order makes
it possible to add the required mmdrop without adding a new error label.
Cc: stable@vger.kernel.org Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 01954dfd48d936199204ae0860897b8aed18c1e2)
This patch fixes an active I/O shutdown bug for fabric
drivers using target_wait_for_sess_cmds(), where se_cmd
descriptor shutdown would result in hung tasks waiting
indefinitely for se_cmd->cmd_wait_comp to complete().
To address this bug, drop the incorrect list_del_init()
usage in target_wait_for_sess_cmds() and always complete()
during se_cmd target_release_cmd_kref() put, in order to
let caller invoke the final fabric release callback
into se_cmd->se_tfo->release_cmd() code.
__clear_bit_unlock() is a special little snowflake. While it carries the
non-atomic '__' prefix, it is specifically documented to pair with
test_and_set_bit() and therefore should be 'somewhat' atomic.
Therefore the generic implementation of __clear_bit_unlock() cannot use
the fully non-atomic __clear_bit() as a default.
If an arch is able to do better; is must provide an implementation of
__clear_bit_unlock() itself.
Specifically, this came up as a result of hackbench livelock'ing in
slab_lock() on ARC with SMP + SLUB + !LLSC.
The non serializing __clear_bit() was getting "lost"
80543b8e: ld_s r2,[r13,0] <--- (A) Finds PG_locked is set 80543b90: or r3,r2,1 <--- (B) other core unlocks right here 80543b94: st_s r3,[r13,0] <--- (C) sets PG_locked (overwrites unlock)
(busybox's cat uses sendfile(2), unlike the coreutils version)
This is because tracing_splice_read_pipe() can call splice_to_pipe()
with spd->nr_pages == 0. spd_pages underflows in splice_to_pipe() and
we fill the page pointers and the other fields of the pipe_buffers with
garbage.
All other callers of splice_to_pipe() avoid calling it when nr_pages ==
0, and we could make tracing_splice_read_pipe() do that too, but it
seems reasonable to have splice_to_page() handle this condition
gracefully.
Cc: stable@vger.kernel.org Signed-off-by: Rabin Vincent <rabin@rab.in> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit ff6c4184945bb5ec843cde5c3936b93823cf5641)
If tracing contains data and the trace_pipe file is read with sendfile(),
then it can trigger a NULL pointer dereference and various BUG_ON within the
VM code.
There's a patch to fix this in the splice_to_pipe() code, but it's also a
good idea to not let that happen from trace_pipe either.
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Cc: stable@vger.kernel.org Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 0b914b30c534502d1d6a68a5859ee65c3d7d8aa5)
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit a635bc779e7b7748c9b0b773eaf08a7f2184ec50)
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit febfaffe4aa9b0600028f46f50156e3354e34208)
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 1
RCU used illegally from extended quiescent state!
no locks held by swapper/3/0.
Move the entering_irq() call before ack_APIC_irq(), because entering_irq()
tells the RCU susbstems to end the extended quiescent state, so that the
following trace call in ack_APIC_irq() works correctly.
Suggested-by: Andi Kleen <ak@linux.intel.com> Fixes: 4787c368a9bc "x86/tracing: Add irq_enter/exit() in smp_trace_reschedule_interrupt()" Signed-off-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit e69b0c2d1686a3344265e26a2ea6197e856f0459)
When setting memory.high below usage, nothing happens until the next
charge comes along, and then it will only reclaim its own charge and not
the now potentially huge excess of the new memory.high. This can cause
groups to stay in excess of their memory.high indefinitely.
To fix that, when shrinking memory.high, kick off a reclaim cycle that
goes after the delta.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 62b3bd2a4f98852cefd0df17333362638246aa8f)
Using an at91sam9g20ek development board with DTS configuration may trigger
a kernel panic because of a NULL pointer dereference exception, while
configuring DMA. Let's fix this by adding a check for pdata before
dereferencing it.
Signed-off-by: Brent Taylor <motobud@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 0db0888f18f37d9ee10e99a7f3e90861b4d525a2)
Commit ecb89f2f5f3e7 ("mmc: atmel-mci: remove compat for non DT board
when requesting dma chan") broke dma on AVR32 and any other boards not
using DT. This restores a fallback mechanism for such cases.
nfsd_lookup_dentry exits with the parent filehandle locked. fh_put also
unlocks if necessary (nfsd filehandle locking is probably too lenient),
so it gets unlocked eventually, but if the following op in the compound
needs to lock it again, we can deadlock.
A fuzzer ran into this; normal clients don't send a secinfo followed by
a readdir in the same compound.
Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 03d44e3d9dd7744fe97ca472fce1725b7179fa2f)
Add some sanity check codes before actually accessing the endpoint via
get_endpoint() in order to avoid the invalid access through a
malformed USB descriptor. Mostly just checking bNumEndpoints, but in
one place (snd_microii_spdif_default_get()), the validity of iface and
altsetting index is checked as well.
create_fixed_stream_quirk() may cause a NULL-pointer dereference by
accessing the non-existing endpoint when a USB device with a malformed
USB descriptor is used.
This patch avoids it simply by adding a sanity check of bNumEndpoints
before the accesses.
Even though hid_hw_* checks that passed in data_len is less than
HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily
allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device
reports and select largest size. In-kernel users normally just send as much
data as report needs, so there is no problem, but hidraw users can do
whatever they please:
Inside multipath_make_request(), multipath maps the incoming
bio into low level device's bio, but it is totally wrong to
copy the bio into mapped bio via '*mapped_bio = *bio'. For
example, .__bi_remaining is kept in the copy, especially if
the incoming bio is chained to via bio splitting, so .bi_end_io
can't be called for the mapped bio at all in the completing path
in this kind of situation.
This patch fixes the issue by using clone style.
Cc: stable@vger.kernel.org (v3.14+) Reported-and-tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 79deb9b280a508c77f6cc233e083544712bc2458)
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
The 'reqs' member of fuse_io_priv serves two purposes. First is to track
the number of oustanding async requests to the server and to signal that
the io request is completed. The second is to be a reference count on the
structure to know when it can be freed.
For sync io requests these purposes can be at odds. fuse_direct_IO() wants
to block until the request is done, and since the signal is sent when
'reqs' reaches 0 it cannot keep a reference to the object. Yet it needs to
use the object after the userspace server has completed processing
requests. This leads to some handshaking and special casing that it
needlessly complicated and responsible for at least one race condition.
It's much cleaner and safer to maintain a separate reference count for the
object lifecycle and to let 'reqs' just be a count of outstanding requests
to the userspace server. Then we can know for sure when it is safe to free
the object without any handshaking or special cases.
The catch here is that most of the time these objects are stack allocated
and should not be freed. Initializing these objects with a single reference
that is never released prevents accidental attempts to free the objects.
There's a race in fuse_direct_IO(), whereby is_sync_kiocb() is called on an
iocb that could have been freed if async io has already completed. The fix
in this case is simple and obvious: cache the result before starting io.
It was discovered by KASan:
kernel: ==================================================================
kernel: BUG: KASan: use after free in fuse_direct_IO+0xb1a/0xcc0 at addr ffff88036c414390
Signed-off-by: Robert Doebbelin <robert@quobyte.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: bcba24ccdc82 ("fuse: enable asynchronous processing direct IO") Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
(cherry picked from commit 19167d65fabb60ff11fc5f9c4a5248c17a12f615)
projects / users / jedix / linux-maple.git / log