Merge tag 'omap-for-v3.17/soc-new' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "SoC related changes for omaps for v3.17 merge window"
from Tony Lindgren:
- Add device tree and hwmod data for various devices
for new SoCs
- Remove legacy mailbox hwmod data that's no longer
needed for SoCs that are DT only. Note that this may
cause a minor merge conflict in mach-omap2/devices.c
with omap_init_mbox() and omap_init_hdmi_audio(), both
are legacy code that is getting removed
* tag 'omap-for-v3.17/soc-new' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Add data for RTC
arm: dra7xx: Add hwmod data for MDIO and CPSW
arm: dra7xx: Add hwmod data for pcie1 and pcie2 subsystems
arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy
ARM: DRA7: hwmod: Add OCP2SCP3 module
ARM: DRA7: hwmod: remove interrupts for DMA
ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver
ARM: AM33xx: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP4: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs
ARM: OMAP2+: Avoid mailbox legacy device creation for DT-boot
ARM: DRA7: hwmod_data: Add mailbox hwmod data
ARM: dts: DRA7: Add mailbox nodes
ARM: dts: AM4372: Correct mailbox node data
ARM: dts: AM33xx: Add mailbox node
ARM: dts: OMAP4: Add mailbox node
ARM: dts: OMAP2+: Add mailbox fifo and user information
ARM: AM43xx: hwmod: add DSS hwmod data
Merge tag 'v3.17-next-mediatek-support' of https://github.com/mbgg/linux-mediatek into next/soc
Merge basic support for the Mediatek Cortex-A7 SoCs from Matthias Brugger:
Support is quite basic, as the only component working up to now are the
timers.
* tag 'v3.17-next-mediatek-support' of https://github.com/mbgg/linux-mediatek:
arm: mediatek: add dts for Aquaris5 mobile phone
dt-bindings: add documentation for Mediatek SoC
arm: add basic support for Mediatek MT6589 boards
Mugunthan V N [Tue, 8 Jul 2014 13:16:39 +0000 (18:46 +0530)]
arm: dra7xx: Add hwmod data for MDIO and CPSW
Adding hwmod data for CPSW and MDIO which is present in DRA7xx SoC
Cc: Rajendra Nayak <rnayak@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kishon Vijay Abraham I [Wed, 9 Jul 2014 09:02:47 +0000 (14:32 +0530)]
arm: dra7xx: Add hwmod data for pcie1 and pcie2 subsystems
Added hwmod data for pcie1 and pcie2 subsystem present in DRA7xx SOC.
Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kishon Vijay Abraham I [Wed, 25 Jun 2014 18:02:45 +0000 (23:32 +0530)]
arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy
Added hwmod data for pcie1 and pcie2 phy present in DRA7xx SOC.
Also added the missing CLKCTRL OFFSET macro and CONTEXT OFFSET macro
for pcie1 phy and pcie2 phy.
Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Nishanth Menon [Thu, 12 Jun 2014 11:45:23 +0000 (17:15 +0530)]
ARM: DRA7: hwmod: remove interrupts for DMA
DMA interrupts are now available in of, and the definitions are
duplicates in hwmod. This prevents us from dynamically allocating
interrupt resources for dma from devicetree.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Thu, 12 Jun 2014 11:45:22 +0000 (17:15 +0530)]
ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver
we have currently 2 DMA drivers that try to co-exist.
drivers/dma/omap-dma.c which registers it's own IRQ and is device tree
aware and uses arch/arm/plat-omap/dma.c instance created by
arch/arm/mach-omap2/dma.c to maintain channel usage (omap_request_dma).
Currently both try to register interrupts and mach-omap2/plat-omap dma.c
attempts to use the IRQ number registered by hwmod to register it's own
interrupt handler.
Now, there is no reasonable way of static allocating DMA irq in GIC
SPI when we use crossbar. However, since the dma_chan structure is
freed as a result of IRQ not being present due to devm allocation,
maintaining information of channel by platform code fails at a later
point in time when that region of memory is reused.
So, if hwmod does not indicate an IRQ number, then, assume that
dma-engine will take care of the interrupt handling.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Sat, 19 Jul 2014 22:03:08 +0000 (15:03 -0700)]
Merge tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung exynos cpuidle update for v3.17" from Kukjin Kim:
- add callbacks exynos_suspend() and exynos_powered_up()
for support cpuidle through mcpm
- skip exynos_cpuidle for exynos5420 because is uses
cpuidle-big-liggle generic cpuidle driver
- add generic functions to calculate cpu number is used
for pmu and this is required for exynos5420 multi-cluster
- add of_device_id structure for big.LITTLE cpuidle and
add "samsung,exynos5420" compatible string for exynos5420
* tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
+ Linux 3.16-rc5
Olof Johansson [Sat, 19 Jul 2014 21:28:06 +0000 (14:28 -0700)]
Merge tag 'mvebu-soc-3.17-2' of git://git.infradead.org/linux-mvebu into next/soc
Merge "ARM: mvebu SoC changes for v3.17 (round 2)" from Jason Cooper:
"Yeah, it's just one patch, but it's a beautiful one! Thanks to the
efforts of many people over the last couple years, and in particular,
Andrew Lunn, Kirkwood has been completely converted to DT."
- kirkwood
* Remove mach-kirkwood/, It's fully supported in mach-mvebu/
* tag 'mvebu-soc-3.17-2' of git://git.infradead.org/linux-mvebu:
ARM: Kirkwood: Remove mach-kirkwood
Olof Johansson [Sat, 19 Jul 2014 19:22:47 +0000 (12:22 -0700)]
Merge tag 'sunxi-core-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Merge "Allwinner core additions for 3.17" from Maxime Ripard:
Nothing very fancy here, only the introduction from the new Allwinner A23 SoC.
* tag 'sunxi-core-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: select MFD_SUN6I_PRCM when sun8i arch support is enabled
ARM: sunxi: Add earlyprintk support using R_UART (sun6i/sun8i)
ARM: sunxi: Introduce Allwinner A23 support
Olof Johansson [Sat, 19 Jul 2014 18:56:39 +0000 (11:56 -0700)]
Merge tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Merge "ARM: imx: SoC changes for 3.17" from Shawn Guo:
The i.MX SoC changes for 3.17:
- Add devicetree support for i.MX1 and i.MX21 clock driver
- Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
- Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
device tree boot
- Remove i.MX1 camera support
- Remove i.MX27 IP Camera and Lite-Kit board support
- Add suspend and cpuidle support for i.mx6sx
- Clean up unused clk_register_clkdev() lookups
- Update imx-weim bus driver to support populating devices on a simple
bus
- Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
- Make i.MX51 a DT only platform and clean up the non-DT support code
- Support disabling supervisor protect via DT
- Random defconfig updates
* tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (69 commits)
ARM: imx: clk-vf610: fix FlexCAN clock gating
ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
ARM: i.MX53: globally disable supervisor protect
ARM: i.MX: allow disabling supervisor protect via DT
ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
ARM: i.MX27 clk: Remove unused definitions
ARM: i.MX27 clk: Introduce DT include for clock provider
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
ARM: i.MX: Remove i.MX1 camera support
ARM: imx: use PTR_ERR_OR_ZERO
bus: imx-weim: populate devices on a simple bus
ARM: imx: build cpu_is_imx6sl function conditionally
ARM: imx: imx6sx uses imx6q cpuidle code
ARM: imx: drop PL310 errata 588369 and 727915
ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
ARM: imx: mark .dt_compat as const
...
Olof Johansson [Sat, 19 Jul 2014 04:30:26 +0000 (21:30 -0700)]
Merge tag 'renesas-clock2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC Clock Updates for v3.17" from
Simon Horman:
- Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow SCI (serial) devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
* tag 'renesas-clock2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: add SCI clock support for DT
ARM: shmobile: r8a7740: correct SCI clock support for DT
ARM: shmobile: r8a73a4: add SCI clock support for DT
ARM: shmobile: r8a7778: add SCI clock support for DT
ARM: EXYNOS: add generic function to calculate cpu number
The address of cpu power registers in pmu is based on cpu number
offsets. This function calculate the same. This is essentially
required in case of multi-cluster SoC's e.g Exynos5420.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This driver will be used by many big.Little Soc's. As of now it does
string matching of hardcoded compatible string to init the driver. This
comparison list will keep on growing with addition of new SoC's.
Hence add of_device_id structure to collect the compatible strings of
SoC's using this driver.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Most peripherals on the i.MX53 have an
Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.
The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
ARM: i.MX: allow disabling supervisor protect via DT
The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Alexander Shiyan [Sat, 5 Jul 2014 05:00:01 +0000 (09:00 +0400)]
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Liu Ying [Fri, 4 Jul 2014 09:00:41 +0000 (17:00 +0800)]
bus: imx-weim: populate devices on a simple bus
There could be some memory map devices located in
a certain chip select region of the i.MX WEIM.
The devices could be attached to a simple bus(for
example, a AXI bus) whose root node is one child
device tree node of the i.MX WEIM device tree node.
There should be a bridge(very likely, software
transparent) bewteen the i.MX WEIM and the simple bus.
This patch makes the i.MX WEIM driver possible to
populate devices on a simple bus. In this way, people
may try various IPs(in a FPGA, maybe) outside of i.MX
chips with the i.MX WEIM embedded.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
ARM: imx: build cpu_is_imx6sl function conditionally
imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'
This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later. Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1. Neither is needed for i.MX6 or VF610. So
let's drop them.
Alexander Shiyan [Sun, 22 Jun 2014 13:17:08 +0000 (17:17 +0400)]
ARM: i.MX21 clk: Cleanup driver
This is a cleanup for i.MX21 clk driver. This change includes:
- Reduce license text.
- Remove unused definitions.
- Remove unused #include and sort the rest.
- Remove useless comment.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 15 Jun 2014 11:35:10 +0000 (19:35 +0800)]
ARM: imx6qdl: switch to use macro for clock ID
Instead of using enum for clock ID, let's switch imx6qdl clock driver to
use macro. In this case, device tree can reuse these macros to improve
readability.
Alexander Shiyan [Wed, 18 Jun 2014 17:26:39 +0000 (21:26 +0400)]
ARM: i.MX: Remove Freescale i.MX27 IP Camera board support
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board. However, the
support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Fri, 13 Jun 2014 07:26:13 +0000 (11:26 +0400)]
ARM: i.MX system: Add a reset fallback if base address of watchdog is not set
This patch adds a reset fallback if base address of watchdog is not set.
This is intended for a targets not compatible with imx-21 watchdog,
i.MX1 for example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 07:46:46 +0000 (15:46 +0800)]
ARM: imx5: remove file mm-imx5.c
The only code left in mm-imx5.c is to create static mapping. While all
IMX platform code are moved to use dynamic mapping, the file can just be
removed now.
Shawn Guo [Tue, 20 May 2014 07:34:06 +0000 (15:34 +0800)]
ARM: imx5: move init hooks into mach-imx5x.c
These imx5 init_early[late] hooks are called only from mach-imx5x.c.
Let's move them into mach-imx5x.c.
While at it, replace the static mapping in imx51_ipu_mipi_setup() with
dynamic mapping. Also this function and imx_src_init() do not
necessarily to be called at .init_early hook, so move them into
.init_machine.
The mxc_iomux_v3_init() is dropped from imx51_init_early() in the
moving, since it's only needed by non-DT boot.
Shawn Guo [Tue, 20 May 2014 06:55:15 +0000 (14:55 +0800)]
ARM: imx5: use dynamic mapping for Cortex and GPC block
The imx5 pm code uses static mapping to access Cortex and GPC registers.
The patch create struct imx5_pm_data to encode physical address of
Cortex and GPC block, and create dynamic mapping for them at run-time.
Shawn Guo [Tue, 20 May 2014 05:41:36 +0000 (13:41 +0800)]
ARM: imx5: reuse clock CCM mapping in pm code
The imx5 pm code needs to access CCM registers. Let's remove the use
of CCM static mapping in pm code by reusing the dynamic mapping created
in clock code.
Shawn Guo [Tue, 20 May 2014 05:08:45 +0000 (13:08 +0800)]
ARM: imx5: use dynamic mapping for DPLL block
Replace the static mapping of DPLL block with dynamic mapping by
calling ioremap(). Ideally, this should be done by calling of_iomap(),
so that the physical address of DPLL can also be retrieved from device
tree. But unfortunately, DPLL blocks are not defined in DT in the first
place. So to maintain the compatibility of existing DTB, we use
ioremap() with physical address defines in the code.
Shawn Guo [Tue, 20 May 2014 03:20:28 +0000 (11:20 +0800)]
ARM: imx5: use dynamic mapping for CCM block
Replace the static mapping of CCM block with dynamic mapping and
retrieve CCM base address from device tree. Though it's not nice to
encode the variable ccm_base in macros, it helps to avoid a massive
churn on the code.
Shawn Guo [Mon, 19 May 2014 14:23:43 +0000 (22:23 +0800)]
ARM: imx5: retrieve iim base from device tree
Instead of using static define and mapping, the patch changes imx5 code
that reads chip revision from IIM to retrieve base address from device
tree and use dynamic mapping.
Shawn Guo [Mon, 19 May 2014 12:19:06 +0000 (20:19 +0800)]
ARM: imx5: tzic_init_irq() can directly be .init_irq hook
After i.MX51 supports DT only, tzic_init_irq() can figure out the
tzic_base on its own. Thus, it can directly be .init_irq hook, and
mx51[53]_init_irq() can be saved.
Shawn Guo [Mon, 19 May 2014 07:47:32 +0000 (15:47 +0800)]
ARM: imx5: drop arguments from mx5_clocks_common_init()
The function mx5_clocks_common_init() was created with a number of
arguments to pass oscillator clock rate in non-DT boot. Since i.MX5
is DT only platform, the arguments can be dropped, and the clock rate
can just be retrieved from device tree.
Shawn Guo [Mon, 19 May 2014 05:47:43 +0000 (13:47 +0800)]
ARM: imx5: drop option MACH_IMX51_DT
Since i.MX51 becomes DT only now, we can drop option MACH_IMX51_DT and
just use SOC_IMX51 instead. While at it, rename imx51-dt.c to
mach-imx51.c to align with the name schema of other IMX DT only
platforms.
Shawn Guo [Mon, 19 May 2014 05:37:50 +0000 (13:37 +0800)]
ARM: imx5: move SOC_IMX5 and SOC_IMX51 into 'Device tree only'
After moving SOC_IMX51 support over to device tree, all i.MX5 support
becomes device tree only now. So options SOC_IMX5 and SOC_IMX51 can
just be under 'Device tree only'.
While at it, 'select ARCH_MXC_IOMUX_V3' is dropped, since it's only
needed by non-DT build before.
Shawn Guo [Mon, 19 May 2014 12:41:52 +0000 (20:41 +0800)]
ARM: imx: move EHCI platform defines out of platform_data header
The platform_data header usb-ehci-mxc.h has a lot of stuff used by only
IMX platform code. They shouldn't be really in this header but a IMX
platform local header. Create ehci.h and move these stuff into it.
Alexander Shiyan [Tue, 20 May 2014 16:43:51 +0000 (20:43 +0400)]
ARM: i.MX: Remove registration helper for i.MX1 USB UDC
imx_udc driver was removed from the kernel of about 10 months ago.
This patch removes a registration helper for this driver and
orphaned driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
It fixes a hard machine hang regression for boards where only pcie is
active but no sata, as the latest imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Lucas Stach [Thu, 17 Jul 2014 10:20:14 +0000 (12:20 +0200)]
ARM: clk-imx6q: parent lvds_sel input from upstream clock gates
The i.MX6 reference manual doesn't make a clear distinction
between the fixed clock divider and the enable gate for the
pcie and sata reference clocks. This lead to the lvds mux
inputs in the imx6q clk driver to be parented from the
ref clock (which is the divider) instead of the actual gate,
which in turn prevents the upstream clock to actually be
enabled when lvds clk out is active.
This fixes a hard machine hang regression in kernel 3.16 for
boards where only pcie is active but no sata, as with this
kernel version the imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Reported-by: Arne Ruhnau <arne.ruhnau@target-sg.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Arne Ruhnau <arne.ruhnau@target-sg.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:47 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/interface: remove some headers from clkt_iclk.c file
Instead, copy the used constants from the header file to the source file.
This allows the code to be migrated under drivers folder where we don't
have access to the OMAP specific header files.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:46 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: remove unused header includes from dpll3xxx.c
Some of the machine specific header includes are no longer used, so remove
these from the source file. This allows migration of the file under clock
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:45 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: remove unused header includes from clkt_dpll.c
Some of the machine specific header includes are no longer used, so remove
these from the source file. This allows migration of the file under clock
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Paul Walmsley <paul@pwsan.com>
projects / users / jedix / linux-maple.git / log