From: Vivian Wang <wangruikang@iscas.ac.cn>
Date: Sun, 14 Sep 2025 04:23:16 +0000 (+0800)
Subject: riscv: dts: spacemit: Add Ethernet support for Jupiter
X-Git-Url: https://www.infradead.org/git/?a=commitdiff_plain;h=e32dc7a936b11e437298bcc4601476befcbcb88f;p=users%2Fhch%2Fmisc.git

riscv: dts: spacemit: Add Ethernet support for Jupiter

Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
reset.

Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250914-net-k1-emac-v12-5-65b31b398f44@iscas.ac.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
---

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 448319214104..89f413277893 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -12,6 +12,8 @@
 	compatible = "milkv,jupiter", "spacemit,k1";
 
 	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
 		serial0 = &uart0;
 	};
 
@@ -20,6 +22,52 @@
 	};
 };
 
+&eth0 {
+	phy-handle = <&rgmii0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii0: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&eth1 {
+	phy-handle = <&rgmii1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <250>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii1: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;