<chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
- reg: Should contain ADC registers location and length
- interrupts: Should contain the IRQ line for the ADC
- - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+ - clock-names: tuple listing input clock names.
+ Required elements: "adc_clk", "adc_op_clk".
+ - clocks: phandles to input clocks.
+ - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
device
- atmel,adc-startup-time: Startup Time of the ADC in microseconds as
defined in the datasheet
Examples:
adc0: adc@fffb0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "atmel,at91sam9260-adc";
reg = <0xfffb0000 0x100>;
- interrupts = <20 4>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&adc_clk>, <&adc_op_clk>;
+ clock-names = "adc_clk", "adc_op_clk";
- atmel,adc-channel-base = <0x30>;
atmel,adc-channels-used = <0xff>;
- atmel,adc-drdy-mask = <0x10000>;
- atmel,adc-num-channels = <8>;
atmel,adc-startup-time = <40>;
- atmel,adc-status-register = <0x1c>;
- atmel,adc-trigger-register = <0x08>;
- atmel,adc-use-external;
+ atmel,adc-use-external-triggers;
atmel,adc-vref = <3300>;
atmel,adc-res = <8 10>;
atmel,adc-res-names = "lowres", "highres";
- resets: Should contain a phandle to the STMMAC reset signal, if any
- reset-names: Should contain the reset signal name "stmmaceth", if a
reset phandle is given
-- max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather
- than the maximum frame size.
+- max-frame-size: See ethernet.txt file in the same directory
+ - clocks: If present, the first clock should be the GMAC main clock,
+ further clocks may be specified in derived bindings.
+ - clocks-names: One name for each entry in the clocks property, the
+ first one should be "stmmaceth".
Examples:
chunghwa Chunghwa Picture Tubes Ltd.
cirrus Cirrus Logic, Inc.
cortina Cortina Systems, Inc.
+crystalfontz Crystalfontz America, Inc.
dallas Maxim Integrated Products (formerly Dallas Semiconductor)
davicom DAVICOM Semiconductor, Inc.
+dlink D-Link Systems, Inc.
denx Denx Software Engineering
+ dmo Data Modul AG
edt Emerging Display Technologies
emmicro EM Microelectronic
epfl Ecole Polytechnique Fédérale de Lausanne
sil Silicon Image
silabs Silicon Laboratories
simtek
+ sii Seiko Instruments, Inc.
sirf SiRF Technology, Inc.
+smsc Standard Microsystems Corporation
snps Synopsys, Inc.
spansion Spansion Inc.
st STMicroelectronics
dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
zynq-zc706.dtb \
zynq-zed.dtb
+ dtb-$(CONFIG_MACH_ARMADA_370) += \
+ armada-370-db.dtb \
+ armada-370-mirabox.dtb \
+ armada-370-netgear-rn102.dtb \
+ armada-370-netgear-rn104.dtb \
+ armada-370-rd.dtb
+ dtb-$(CONFIG_MACH_ARMADA_375) += \
+ armada-375-db.dtb
+ dtb-$(CONFIG_MACH_ARMADA_38X) += \
+ armada-385-db.dtb \
+ armada-385-rd.dtb
+ dtb-$(CONFIG_MACH_ARMADA_XP) += \
+ armada-xp-axpwifiap.dtb \
+ armada-xp-db.dtb \
+ armada-xp-gp.dtb \
+ armada-xp-netgear-rn2120.dtb \
+ armada-xp-matrix.dtb \
+ armada-xp-openblocks-ax3-4.dtb
+ dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
+ dove-cubox.dtb \
+ dove-d2plug.dtb \
+ dove-d3plug.dtb \
+ dove-dove-db.dtb
-targets += dtbs
+targets += dtbs dtbs_install
targets += $(dtb-y)
endif
display@di1 {
compatible = "fsl,imx-parallel-display";
- crtcs = <&ipu 0>;
interface-pix-fmt = "bgr666";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu_disp1_1>;
+ pinctrl-0 = <&pinctrl_ipu_disp1>;
display-timings {
lw700 {
MX51_PAD_GPIO1_3__GPIO1_3 0x0C5
>;
};
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
+ MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185
+ MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX51_PAD_NANDF_RB3__ECSPI2_MISO 0x185
+ MX51_PAD_NANDF_D15__ECSPI2_MOSI 0x185
+ MX51_PAD_NANDF_RB2__ECSPI2_SCLK 0x185
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
+ MX51_PAD_SD1_CLK__SD1_CLK 0x20d5
+ MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5
+ MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5
+ MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5
+ MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5
+ >;
+ };
+
+ pinctrl_esdhc2: esdhc2grp {
+ fsl,pins = <
+ MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5
+ MX51_PAD_SD2_CLK__SD2_CLK 0x20d5
+ MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d5
+ MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d5
+ MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d5
+ MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d5
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX51_PAD_EIM_D27__I2C2_SCL 0x400001ed
+ MX51_PAD_EIM_D24__I2C2_SDA 0x400001ed
+ >;
+ };
+
+ pinctrl_ipu_disp1: ipudisp1grp {
+ fsl,pins = <
+ MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5
+ MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5
+ MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5
+ MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5
+ MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5
+ MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5
+ MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5
+ MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5
+ MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5
+ MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5
+ MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5
+ MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5
+ MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5
+ MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5
+ MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5
+ MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5
+ MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5
+ MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5
+ MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5
+ MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5
+ MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5
+ MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5
+ MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5
+ MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5
+ MX51_PAD_DI1_PIN2__DI1_PIN2 0x5
+ MX51_PAD_DI1_PIN3__DI1_PIN3 0x5
+ >;
+ };
};
};
+
+&ipu_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
reg = <0x90000000 0x20000000>;
};
- display@di0 {
+ display0: display@di0 {
compatible = "fsl,imx-parallel-display";
- crtcs = <&ipu 0>;
interface-pix-fmt = "rgb24";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu_disp1_1>;
+ pinctrl-0 = <&pinctrl_ipu_disp1>;
display-timings {
native-mode = <&timing0>;
timing0: dvi {
vsync-len = <10>;
};
};
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu_di0_disp0>;
+ };
+ };
};
- display@di1 {
+ display1: display@di1 {
compatible = "fsl,imx-parallel-display";
- crtcs = <&ipu 1>;
interface-pix-fmt = "rgb565";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu_disp2_1>;
+ pinctrl-0 = <&pinctrl_ipu_disp2>;
status = "disabled";
display-timings {
native-mode = <&timing1>;
compatible = "fsl,imx51-ipu";
reg = <0x40000000 0x20000000>;
interrupts = <11 10>;
- clocks = <&clks 59>, <&clks 110>, <&clks 61>;
+ clocks = <&clks IMX5_CLK_IPU_GATE>,
+ <&clks IMX5_CLK_IPU_DI0_GATE>,
+ <&clks IMX5_CLK_IPU_DI1_GATE>;
clock-names = "bus", "di0", "di1";
resets = <&src 2>;
+
+ ipu_di0: port@2 {
+ reg = <2>;
+
+ ipu_di0_disp0: endpoint {
+ };
+ };
+
+ ipu_di1: port@3 {
+ reg = <3>;
+
+ ipu_di1_disp1: endpoint {
+ };
+ };
};
aips@70000000 { /* AIPS1 */
};
soc {
- display@di1 {
+ display1: display@di1 {
compatible = "fsl,imx-parallel-display";
- crtcs = <&ipu 1>;
interface-pix-fmt = "bgr666";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu_disp2_1>;
+ pinctrl-0 = <&pinctrl_ipu_disp1>;
display-timings {
800x480p60 {
};
};
+&ipu_di1_disp1 {
+ remote-endpoint = <&display1_in>;
+};
+
&nfc {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_nand_1>;
+ pinctrl-0 = <&pinctrl_nand>;
nand-bus-width = <8>;
nand-ecc-mode = "hw";
status = "okay";
compatible = "fsl,imx-parallel-display";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp1_1>;
- crtcs = <&ipu 1>;
interface-pix-fmt = "rgb24";
status = "disabled";
+
+ port {
+ display1_in: endpoint {
+ remote-endpoint = <&ipu_di1_disp1>;
+ };
+ };
};
- reg_3p2v: 3p2v {
- compatible = "regulator-fixed";
- regulator-name = "3P2V";
- regulator-min-microvolt = <3200000>;
- regulator-max-microvolt = <3200000>;
- regulator-always-on;
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_backlight: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "lcd-supply";
+ gpio = <&gpio2 5 0>;
+ startup-delay-us = <5000>;
+ };
+
+ reg_3p2v: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "3P2V";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-always-on;
+ };
};
sound {
--- /dev/null
- display@di0 {
+ /*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+ #include "imx53.dtsi"
+
+ / {
+ memory {
+ reg = <0x70000000 0x40000000>;
+ };
+
- crtcs = <&ipu 0>;
++ display0: display@di0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb565";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp0>;
+ status = "disabled";
+ display-timings {
+ claawvga {
+ native-mode;
+ clock-frequency = <27000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <40>;
+ hfront-porch = <60>;
+ vback-porch = <10>;
+ vfront-porch = <10>;
+ hsync-len = <20>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
++
++ port {
++ display0_in: endpoint {
++ remote-endpoint = <&ipu_di0_disp0>;
++ };
++ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio1 8 0>;
+ linux,code = <116>; /* KEY_POWER */
+ };
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio2 14 0>;
+ linux,code = <115>; /* KEY_VOLUMEUP */
+ gpio-key,wakeup;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio2 15 0>;
+ linux,code = <114>; /* KEY_VOLUMEDOWN */
+ gpio-key,wakeup;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio7_7>;
+
+ user {
+ label = "Heartbeat";
+ gpios = <&gpio7 7 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p2v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3P2V";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-always-on;
+ };
+
+ reg_usb_vbus: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio7 8 0>;
+ enable-active-high;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx53-qsb-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx53-qsb-sgtl5000";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <2>;
+ mux-ext-port = <5>;
+ };
+ };
+
+ &esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "okay";
+ };
+
++&ipu_di0_disp0 {
++ remote-endpoint = <&display0_in>;
++};
++
+ &ssi2 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+ };
+
+ &esdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc3>;
+ cd-gpios = <&gpio3 11 0>;
+ wp-gpios = <&gpio3 12 0>;
+ bus-width = <8>;
+ status = "okay";
+ };
+
+ &iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx53-qsb {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000
+ MX53_PAD_GPIO_8__GPIO1_8 0x80000000
+ MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000
+ MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000
+ MX53_PAD_EIM_DA11__GPIO3_11 0x80000000
+ MX53_PAD_EIM_DA12__GPIO3_12 0x80000000
+ MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000
+ MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000
+ MX53_PAD_GPIO_16__GPIO7_11 0x80000000
+ >;
+ };
+
+ led_pin_gpio7_7: led_gpio7_7@0 {
+ fsl,pins = <
+ MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000
+ MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000
+ MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000
+ MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_esdhc3: esdhc3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
+ MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
+ MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
+ MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
+ MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
+ MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
+ MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
+ MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
+ MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
+ MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX53_PAD_FEC_MDC__FEC_MDC 0x80000000
+ MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000
+ MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000
+ MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000
+ MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000
+ MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000
+ MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000
+ MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000
+ MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000
+ MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0xc0000000
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0xc0000000
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000
+ MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000
+ >;
+ };
+
+ pinctrl_ipu_disp0: ipudisp0grp {
+ fsl,pins = <
+ MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK 0x5
+ MX53_PAD_DI0_PIN15__IPU_DI0_PIN15 0x5
+ MX53_PAD_DI0_PIN2__IPU_DI0_PIN2 0x5
+ MX53_PAD_DI0_PIN3__IPU_DI0_PIN3 0x5
+ MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0 0x5
+ MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1 0x5
+ MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2 0x5
+ MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3 0x5
+ MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4 0x5
+ MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5 0x5
+ MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6 0x5
+ MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7 0x5
+ MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8 0x5
+ MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9 0x5
+ MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10 0x5
+ MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11 0x5
+ MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12 0x5
+ MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13 0x5
+ MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14 0x5
+ MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15 0x5
+ MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16 0x5
+ MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17 0x5
+ MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18 0x5
+ MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19 0x5
+ MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20 0x5
+ MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21 0x5
+ MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22 0x5
+ MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23 0x5
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
+ >;
+ };
+ };
+ };
+
+ &uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+ };
+
+ &i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3p2v>;
+ VDDIO-supply = <®_3p2v>;
+ clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+ };
+ };
+
+ &i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ accelerometer: mma8450@1c {
+ compatible = "fsl,mma8450";
+ reg = <0x1c>;
+ };
+ };
+
+ &audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+ };
+
+ &fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio7 6 0>;
+ status = "okay";
+ };
+
+ &sata {
+ status = "okay";
+ };
+
+ &vpu {
+ status = "okay";
+ };
+
+ &usbh1 {
+ vbus-supply = <®_usb_vbus>;
+ phy_type = "utmi";
+ status = "okay";
+ };
+
+ &usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+ };
interrupt-parent = <&tzic>;
ranges;
+ sata: sata@10000000 {
+ compatible = "fsl,imx53-ahci";
+ reg = <0x10000000 0x1000>;
+ interrupts = <28>;
+ clocks = <&clks IMX5_CLK_SATA_GATE>,
+ <&clks IMX5_CLK_SATA_REF>,
+ <&clks IMX5_CLK_AHB>;
+ clock-names = "sata_gate", "sata_ref", "ahb";
+ status = "disabled";
+ };
+
ipu: ipu@18000000 {
- #crtc-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,imx53-ipu";
reg = <0x18000000 0x080000000>;
interrupts = <11 10>;
- clocks = <&clks 59>, <&clks 110>, <&clks 61>;
+ clocks = <&clks IMX5_CLK_IPU_GATE>,
+ <&clks IMX5_CLK_IPU_DI0_GATE>,
+ <&clks IMX5_CLK_IPU_DI1_GATE>;
clock-names = "bus", "di0", "di1";
resets = <&src 2>;
+
+ ipu_di0: port@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ ipu_di0_disp0: endpoint@0 {
+ reg = <0>;
+ };
+
+ ipu_di0_lvds0: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&lvds0_in>;
+ };
+ };
+
+ ipu_di1: port@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ ipu_di1_disp1: endpoint@0 {
+ reg = <0>;
+ };
+
+ ipu_di1_lvds1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&lvds1_in>;
+ };
+
+ ipu_di1_tve: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&tve_in>;
+ };
+ };
};
aips@50000000 { /* AIPS1 */
compatible = "fsl,imx53-tve";
reg = <0x63ff0000 0x1000>;
interrupts = <92>;
- clocks = <&clks 69>, <&clks 116>;
+ clocks = <&clks IMX5_CLK_TVE_GATE>,
+ <&clks IMX5_CLK_IPU_DI1_SEL>;
clock-names = "tve", "di_sel";
- crtcs = <&ipu 1>;
status = "disabled";
+
+ port {
+ tve_in: endpoint {
+ remote-endpoint = <&ipu_di1_tve>;
+ };
+ };
};
vpu: vpu@63ff4000 {
};
ipu2: ipu@02800000 {
- #crtc-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,imx6q-ipu";
reg = <0x02800000 0x400000>;
- interrupts = <0 8 0x4 0 7 0x4>;
+ interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
+ <0 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks 133>, <&clks 134>, <&clks 137>;
clock-names = "bus", "di0", "di1";
resets = <&src 4>;
};
ipu1: ipu@02400000 {
- #crtc-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,imx6q-ipu";
reg = <0x02400000 0x400000>;
- interrupts = <0 6 0x4 0 5 0x4>;
+ interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>,
+ <0 5 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks 130>, <&clks 131>, <&clks 132>;
clock-names = "bus", "di0", "di1";
resets = <&src 2>;
compatible = "qcom,msm8960";
interrupt-parent = <&intc>;
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <1 14 0x304>;
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v1";
+
+ cpu@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ interrupts = <0 2 0x4>;
+ };
+ };
+
+ cpu-pmu {
+ compatible = "qcom,krait-pmu";
+ interrupts = <1 10 0x304>;
+ qcom,no-pc-write;
+ };
+
intc: interrupt-controller@2000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
compatible = "qcom,msm8974";
interrupt-parent = <&intc>;
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <1 9 0xf04>;
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v2";
+
+ cpu@0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ };
+
+ cpu@2 {
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc2>;
+ };
+
+ cpu@3 {
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc3>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ interrupts = <0 2 0x4>;
+ qcom,saw = <&saw_l2>;
+ };
+ };
+
+ cpu-pmu {
+ compatible = "qcom,krait-pmu";
+ interrupts = <1 7 0xf04>;
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
#size-cells = <0>;
};
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun4i-a10-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+ reg-names = "phy_ctrl", "pmu1", "pmu2";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 1>, <&usb_clk 2>;
+ reset-names = "usb1_reset", "usb2_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <64>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ahci: sata@01c18000 {
+ compatible = "allwinner,sun4i-a10-ahci";
+ reg = <0x01c18000 0x1000>;
+ interrupts = <56>;
+ clocks = <&pll6 0>, <&ahb_gates 25>;
+ status = "disabled";
+ };
+
+ ehci1: usb@01c1c000 {
+ compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <40>;
+ clocks = <&ahb_gates 3>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1c400 {
+ compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <65>;
+ clocks = <&usb_clk 7>, <&ahb_gates 4>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi3: spi@01c1f000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c1f000 0x1000>;
+ interrupts = <50>;
+ clocks = <&ahb_gates 23>, <&spi3_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
intc: interrupt-controller@01c20400 {
- compatible = "allwinner,sun4i-ic";
+ compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
interrupt-controller;
#interrupt-cells = <1>;
#size-cells = <0>;
};
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 1>;
+ reset-names = "usb1_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun5i-a10s-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun5i-a10s-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <40>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
intc: interrupt-controller@01c20400 {
- compatible = "allwinner,sun4i-ic";
+ compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
interrupt-controller;
#interrupt-cells = <1>;
#size-cells = <1>;
ranges;
+ spi0: spi@01c05000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c05000 0x1000>;
+ interrupts = <10>;
+ clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c06000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c06000 0x1000>;
+ interrupts = <11>;
+ clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 1>;
+ reset-names = "usb1_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <40>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
intc: interrupt-controller@01c20400 {
- compatible = "allwinner,sun4i-ic";
+ compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
interrupt-controller;
#interrupt-cells = <1>;
#size-cells = <1>;
ranges;
+ nmi_intc: interrupt-controller@01c00030 {
+ compatible = "allwinner,sun7i-a20-sc-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01c00030 0x0c>;
+ interrupts = <0 0 4>;
+ };
+
+ spi0: spi@01c05000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c05000 0x1000>;
+ interrupts = <0 10 4>;
+ clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c06000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c06000 0x1000>;
+ interrupts = <0 11 4>;
+ clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
emac: ethernet@01c0b000 {
compatible = "allwinner,sun4i-a10-emac";
reg = <0x01c0b000 0x1000>;
#include "common-board-devices.h"
#include "dss-common.h"
#include "control.h"
+ #include "omap_device.h"
+#include "omap-secure.h"
+#include "soc.h"
struct pdata_init {
const char *compatible;
omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */
}
+ static struct gpio cm_t3517_wlan_gpios[] __initdata = {
+ { 56, GPIOF_OUT_INIT_HIGH, "wlan pwr" },
+ { 4, GPIOF_OUT_INIT_HIGH, "xcvr noe" },
+ };
+
+ static void __init omap3_sbc_t3517_wifi_init(void)
+ {
+ int err = gpio_request_array(cm_t3517_wlan_gpios,
+ ARRAY_SIZE(cm_t3517_wlan_gpios));
+ if (err) {
+ pr_err("SBC-T3517: wl12xx gpios request failed: %d\n", err);
+ return;
+ }
+
+ gpio_export(cm_t3517_wlan_gpios[0].gpio, 0);
+ gpio_export(cm_t3517_wlan_gpios[1].gpio, 0);
+
+ msleep(100);
+ gpio_set_value(cm_t3517_wlan_gpios[1].gpio, 0);
+ }
+
+ static void __init omap3_sbc_t3517_legacy_init(void)
+ {
+ omap3_sbc_t3x_usb_hub_init(152, "cm-t3517 usb hub");
+ omap3_sbc_t3x_usb_hub_init(98, "sb-t35 usb hub");
+ am35xx_emac_reset();
+ hsmmc2_internal_input_clk();
+ omap3_sbc_t3517_wifi_init();
+ legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 145);
+ omap_ads7846_init(1, 57, 0, NULL);
+ }
+
+ static void __init am3517_evm_legacy_init(void)
+ {
+ am35xx_emac_reset();
+ }
++
+static void __init nokia_n900_legacy_init(void)
+{
+ hsmmc2_internal_input_clk();
+
+ if (omap_type() == OMAP2_DEVICE_TYPE_SEC) {
+ if (IS_ENABLED(CONFIG_ARM_ERRATA_430973)) {
+ pr_info("RX-51: Enabling ARM errata 430973 workaround\n");
+ /* set IBE to 1 */
+ rx51_secure_update_aux_cr(BIT(6), 0);
+ } else {
+ pr_warning("RX-51: Not enabling ARM errata 430973 workaround\n");
+ pr_warning("Thumb binaries may crash randomly without this workaround\n");
+ }
+ }
+}
#endif /* CONFIG_ARCH_OMAP3 */
#ifdef CONFIG_ARCH_OMAP4
#endif
#ifdef CONFIG_ARCH_OMAP3
OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata),
+ OF_DEV_AUXDATA("ti,omap3-padconf", 0x480025a0, "480025a0.pinmux", &pcs_pdata),
OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata),
+ OF_DEV_AUXDATA("ti,omap2-iommu", 0x5d000000, "5d000000.mmu",
+ &omap3_iommu_pdata),
/* Only on am3517 */
OF_DEV_AUXDATA("ti,davinci_mdio", 0x5c030000, "davinci_mdio.0", NULL),
OF_DEV_AUXDATA("ti,am3517-emac", 0x5c000000, "davinci_emac.0",
*/
static struct pdata_init pdata_quirks[] __initdata = {
#ifdef CONFIG_ARCH_OMAP3
+ { "compulab,omap3-sbc-t3517", omap3_sbc_t3517_legacy_init, },
+ { "compulab,omap3-sbc-t3530", omap3_sbc_t3530_legacy_init, },
{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
- { "nokia,omap3-n900", hsmmc2_internal_input_clk, },
+ { "nokia,omap3-n900", nokia_n900_legacy_init, },
{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
{ "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
projects / users / jedix / linux-maple.git / commitdiff