arm64: dts: marvell: cn9130-crb: drop wrong unit-addresses

Top-level nodes, not being on MMIO bus, do not have "reg" properties and
should not have unit addresses.  Correct their name as well to match
"Generic node names" recommendation from Devicetree specification.
This also fixes dtc W=1 warnings:

  cn9130-crb.dtsi:29.35-37.4: Warning (unit_address_vs_reg): /ap0_mmc_vccq@0: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:39.38-46.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus@1: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:57.33-65.4: Warning (unit_address_vs_reg): /cp0_sd_vccq@0: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:67.31-75.4: Warning (unit_address_vs_reg): /cp0_sd_vcc@0: node has a unit name, but no reg or ranges property

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 6fcc34f7b46474545404641c6a775f7dbeca3b82..d48dd6bca6e5aca8430fbfdbad03099dcd030144 100644 (file)
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -26,7 +26,7 @@
                reg = <0x0 0x0 0x0 0x80000000>;
        };
 
-       ap0_reg_mmc_vccq: ap0_mmc_vccq@0 {
+       ap0_reg_mmc_vccq: regulator-1 {
                compatible = "regulator-gpio";
                regulator-name = "ap0_mmc_vccq";
                regulator-min-microvolt = <1800000>;
@@ -36,7 +36,7 @@
                          3300000 0x0>;
        };
 
-       cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+       cp0_reg_usb3_vbus1: regulator-2 {
                compatible = "regulator-fixed";
                regulator-name = "cp0-xhci1-vbus";
                regulator-min-microvolt = <5000000>;
@@ -45,16 +45,16 @@
                gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
        };
 
-       cp0_usb3_0_phy0: cp0_usb3_phy0 {
+       cp0_usb3_0_phy0: usb-phy-1 {
                compatible = "usb-nop-xceiv";
        };
 
-       cp0_usb3_0_phy1: cp0_usb3_phy1 {
+       cp0_usb3_0_phy1: usb-phy-2 {
                compatible = "usb-nop-xceiv";
                vcc-supply = <&cp0_reg_usb3_vbus1>;
        };
 
-       cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+       cp0_reg_sd_vccq: regulator-3 {
                compatible = "regulator-gpio";
                regulator-name = "cp0_sd_vccq";
                regulator-min-microvolt = <1800000>;
@@ -64,7 +64,7 @@
                          3300000 0x0>;
        };
 
-       cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+       cp0_reg_sd_vcc: regulator-4 {
                compatible = "regulator-fixed";
                regulator-name = "cp0_sd_vcc";
                regulator-min-microvolt = <3300000>;