#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN 0x0200
+#define HV_SMB_ADDR_VALID 0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP 0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
/* OEM Bits Phy Register */
#define HV_OEM_BITS PHY_REG(768, 25)
#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
return 0;
}
+/**
+ * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ *
+ * SW should configure the LCD from the NVM extended configuration region
+ * as a workaround for certain parts.
+ **/
+static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+ (hw->mac.type == e1000_pchlan)) {
+ struct e1000_adapter *adapter = hw->adapter;
+
+ /* Check if SW needs to configure the PHY */
+ if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
+ (hw->mac.type == e1000_pchlan))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ goto out;
+
+ /* Wait for basic configuration completes before proceeding */
+ e1000_lan_init_done_ich8lan(hw);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ goto out;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ goto out;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+ (hw->mac.type == e1000_pchlan)) {
+ /*
+ * HW configures the SMBus address and LEDs when the
+ * OEM and LCD Write Enable bits are set in the NVM.
+ * When both NVM bits are cleared, SW will configure
+ * them instead.
+ */
+ data = er32(STRAP);
+ data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+ reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+ reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+ ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ data = er32(LEDCTL);
+ ret_val = e1000_write_phy_reg_hv_locked(hw,
+ HV_LED_CONFIG,
+ (u16)data);
+ if (ret_val)
+ goto out;
+ }
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
+ ®_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
+ 1, ®_addr);
+ if (ret_val)
+ goto out;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr &= PHY_REG_MASK;
+ reg_addr |= phy_page;
+
+ ret_val = phy->ops.write_phy_reg_locked(hw,
+ (u32)reg_addr,
+ reg_data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ * @d0_state: boolean if entering d0 or d3 device state
+ *
+ * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
+ * in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+ s32 ret_val = 0;
+ u32 mac_reg;
+ u16 oem_reg;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ mac_reg = er32(EXTCNF_CTRL);
+ if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+ goto out;
+
+ mac_reg = er32(FEXTNVM);
+ if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+ goto out;
+
+ mac_reg = er32(PHY_CTRL);
+
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+ if (d0_state) {
+ if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ } else {
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ }
+ /* Restart auto-neg to activate the bits */
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+
/**
* e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
* done after every PHY reset.
**/
static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i;
- u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
- s32 ret_val;
- u16 reg, word_addr, reg_data, reg_addr, phy_page = 0;
+ s32 ret_val = 0;
+ u16 reg;
ret_val = e1000e_phy_hw_reset_generic(hw);
if (ret_val)
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, ®);
- /*
- * Initialize the PHY from the NVM on ICH platforms. This
- * is needed due to an issue where the NVM configuration is
- * not properly autoloaded after power transitions.
- * Therefore, after each PHY reset, we will load the
- * configuration data out of the NVM manually.
- */
- if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
- struct e1000_adapter *adapter = hw->adapter;
-
- /* Check if SW needs configure the PHY */
- if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
- (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
- else
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
-
- data = er32(FEXTNVM);
- if (!(data & sw_cfg_mask))
- return 0;
-
- /* Wait for basic configuration completes before proceeding */
- e1000_lan_init_done_ich8lan(hw);
-
- /*
- * Make sure HW does not configure LCD from PHY
- * extended configuration before SW configuration
- */
- data = er32(EXTCNF_CTRL);
- if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
- return 0;
-
- cnf_size = er32(EXTCNF_SIZE);
- cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
- cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
- if (!cnf_size)
- return 0;
-
- cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
- cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
-
- /* Configure LCD from extended configuration region. */
-
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
-
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2),
- 1,
- ®_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2 + 1),
- 1,
- ®_addr);
- if (ret_val)
- return ret_val;
-
- /* Save off the PHY page for future writes. */
- if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
- phy_page = reg_data;
- continue;
- }
-
- reg_addr |= phy_page;
+ /* Configure the LCD with the extended configuration region in NVM */
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
- ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
- if (ret_val)
- return ret_val;
- }
- }
+ /* Configure the LCD with the OEM bits in NVM */
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+out:
return 0;
}
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, ®);
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+ if (ret_val)
+ goto out;
+ }
/*
* For PCH, this write will make sure that any noise
* will be detected as a CRC error and be dropped rather than show up
if (hw->mac.type == e1000_pchlan)
ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+out:
return ret_val;
}
projects / users / jedix / linux-maple.git / commitdiff