drivers: net: atp: fix various indentation issues

There are various lines that have indentation issues, fix these.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/ethernet/realtek/atp.c b/drivers/net/ethernet/realtek/atp.c
index 7e011c1c1e6e918aa3dbde55ff726cd6dc4bb6c5..cfb67b7465958ec4eb6ae8aa68003a777052310b 100644 (file)
--- a/drivers/net/ethernet/realtek/atp.c
+++ b/drivers/net/ethernet/realtek/atp.c
@@ -454,14 +454,14 @@ static void hardware_init(struct net_device *dev)
 {
        struct net_local *lp = netdev_priv(dev);
        long ioaddr = dev->base_addr;
-    int i;
+       int i;
 
        /* Turn off the printer multiplexer on the 8012. */
        for (i = 0; i < 8; i++)
                outb(mux_8012[i], ioaddr + PAR_DATA);
        write_reg_high(ioaddr, CMR1, CMR1h_RESET);
 
-    for (i = 0; i < 6; i++)
+       for (i = 0; i < 6; i++)
                write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]);
 
        write_reg_high(ioaddr, CMR2, lp->addr_mode);
@@ -471,15 +471,15 @@ static void hardware_init(struct net_device *dev)
                           (read_nibble(ioaddr, CMR2_h) >> 3) & 0x0f);
        }
 
-    write_reg(ioaddr, CMR2, CMR2_IRQOUT);
-    write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
+       write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+       write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
 
        /* Enable the interrupt line from the serial port. */
        outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
 
        /* Unmask the interesting interrupts. */
-    write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
-    write_reg_high(ioaddr, IMR, ISRh_RxErr);
+       write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
+       write_reg_high(ioaddr, IMR, ISRh_RxErr);
 
        lp->tx_unit_busy = 0;
     lp->pac_cnt_in_tx_buf = 0;
@@ -610,10 +610,12 @@ static irqreturn_t atp_interrupt(int irq, void *dev_instance)
        write_reg(ioaddr, CMR2, CMR2_NULL);
        write_reg(ioaddr, IMR, 0);
 
-       if (net_debug > 5) printk(KERN_DEBUG "%s: In interrupt ", dev->name);
-    while (--boguscount > 0) {
+       if (net_debug > 5)
+               printk(KERN_DEBUG "%s: In interrupt ", dev->name);
+       while (--boguscount > 0) {
                int status = read_nibble(ioaddr, ISR);
-               if (net_debug > 5) printk("loop status %02x..", status);
+               if (net_debug > 5)
+                       printk("loop status %02x..", status);
 
                if (status & (ISR_RxOK<<3)) {
                        handled = 1;
@@ -640,7 +642,8 @@ static irqreturn_t atp_interrupt(int irq, void *dev_instance)
                        } while (--boguscount > 0);
                } else if (status & ((ISR_TxErr + ISR_TxOK)<<3)) {
                        handled = 1;
-                       if (net_debug > 6)  printk("handling Tx done..");
+                       if (net_debug > 6)
+                               printk("handling Tx done..");
                        /* Clear the Tx interrupt.  We should check for too many failures
                           and reinitialize the adapter. */
                        write_reg(ioaddr, ISR, ISR_TxErr + ISR_TxOK);
@@ -680,7 +683,7 @@ static irqreturn_t atp_interrupt(int irq, void *dev_instance)
                        break;
                } else
                        break;
-    }
+       }
 
        /* This following code fixes a rare (and very difficult to track down)
           problem where the adapter forgets its ethernet address. */
@@ -694,7 +697,7 @@ static irqreturn_t atp_interrupt(int irq, void *dev_instance)
        }
 
        /* Tell the adapter that it can go back to using the output line as IRQ. */
-    write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+       write_reg(ioaddr, CMR2, CMR2_IRQOUT);
        /* Enable the physical interrupt line, which is sure to be low until.. */
        outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
        /* .. we enable the interrupt sources. */