video: xilinxfb: Do not name out_be32 in function name

out_be32 IO function is not supported by ARM.
It is only available for PPC and Microblaze.
Because this driver can be used on ARM let's
remove out_be32 from function name.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

diff --git a/drivers/video/xilinxfb.c b/drivers/video/xilinxfb.c
index aecd15d0b8e5c35a4c2c98b3043bc69e50a8b2c2..c9b442b928e5f18c2469b91b6d0a60f8019b9972 100644 (file)
--- a/drivers/video/xilinxfb.c
+++ b/drivers/video/xilinxfb.c
@@ -57,7 +57,7 @@
  * In case of direct PLB access the second control register will be at
  * an offset of 4 as compared to the DCR access where the offset is 1
  * i.e. REG_CTRL. So this is taken care in the function
- * xilinx_fb_out_be32 where it left shifts the offset 2 times in case of
+ * xilinx_fb_out32 where it left shifts the offset 2 times in case of
  * direct PLB access.
  */
 #define NUM_REGS       2
@@ -150,7 +150,7 @@ struct xilinxfb_drvdata {
  * To perform the read/write on the registers we need to check on
  * which bus its connected and call the appropriate write API.
  */
-static void xilinx_fb_out_be32(struct xilinxfb_drvdata *drvdata, u32 offset,
+static void xilinx_fb_out32(struct xilinxfb_drvdata *drvdata, u32 offset,
                                u32 val)
 {
        if (drvdata->flags & PLB_ACCESS_FLAG)
@@ -197,7 +197,7 @@ xilinx_fb_blank(int blank_mode, struct fb_info *fbi)
        switch (blank_mode) {
        case FB_BLANK_UNBLANK:
                /* turn on panel */
-               xilinx_fb_out_be32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
+               xilinx_fb_out32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
                break;
 
        case FB_BLANK_NORMAL:
@@ -205,7 +205,7 @@ xilinx_fb_blank(int blank_mode, struct fb_info *fbi)
        case FB_BLANK_HSYNC_SUSPEND:
        case FB_BLANK_POWERDOWN:
                /* turn off panel */
-               xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+               xilinx_fb_out32(drvdata, REG_CTRL, 0);
        default:
                break;
 
@@ -280,13 +280,13 @@ static int xilinxfb_assign(struct device *dev,
        memset_io((void __iomem *)drvdata->fb_virt, 0, fbsize);
 
        /* Tell the hardware where the frame buffer is */
-       xilinx_fb_out_be32(drvdata, REG_FB_ADDR, drvdata->fb_phys);
+       xilinx_fb_out32(drvdata, REG_FB_ADDR, drvdata->fb_phys);
 
        /* Turn on the display */
        drvdata->reg_ctrl_default = REG_CTRL_ENABLE;
        if (pdata->rotate_screen)
                drvdata->reg_ctrl_default |= REG_CTRL_ROTATE;
-       xilinx_fb_out_be32(drvdata, REG_CTRL,
+       xilinx_fb_out32(drvdata, REG_CTRL,
                                        drvdata->reg_ctrl_default);
 
        /* Fill struct fb_info */
@@ -345,7 +345,7 @@ err_cmap:
                iounmap(drvdata->fb_virt);
 
        /* Turn off the display */
-       xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+       xilinx_fb_out32(drvdata, REG_CTRL, 0);
 
 err_fbmem:
        if (drvdata->flags & PLB_ACCESS_FLAG)
@@ -381,7 +381,7 @@ static int xilinxfb_release(struct device *dev)
                iounmap(drvdata->fb_virt);
 
        /* Turn off the display */
-       xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+       xilinx_fb_out32(drvdata, REG_CTRL, 0);
 
        /* Release the resources, as allocated based on interface */
        if (drvdata->flags & PLB_ACCESS_FLAG) {