--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/* Realtek Simple Management Interface (SMI) driver
+ * It can be discussed how "simple" this interface is.
+ *
+ * The SMI protocol piggy-backs the MDIO MDC and MDIO signals levels
+ * but the protocol is not MDIO at all. Instead it is a Realtek
+ * pecularity that need to bit-bang the lines in a special way to
+ * communicate with the switch.
+ *
+ * ASICs we intend to support with this driver:
+ *
+ * RTL8366 - The original version, apparently
+ * RTL8369 - Similar enough to have the same datsheet as RTL8366
+ * RTL8366RB - Probably reads out "RTL8366 revision B", has a quite
+ * different register layout from the other two
+ * RTL8366S - Is this "RTL8366 super"?
+ * RTL8367 - Has an OpenWRT driver as well
+ * RTL8368S - Seems to be an alternative name for RTL8366RB
+ * RTL8370 - Also uses SMI
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/spinlock.h>
+#include <linux/skbuff.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/bitops.h>
+#include <linux/if_bridge.h>
+
+#include "realtek-smi.h"
+
+#define REALTEK_SMI_ACK_RETRY_COUNT 5
+#define REALTEK_SMI_HW_STOP_DELAY 25 /* msecs */
+#define REALTEK_SMI_HW_START_DELAY 100 /* msecs */
+
+static inline void realtek_smi_clk_delay(struct realtek_smi *smi)
+{
+ ndelay(smi->clk_delay);
+}
+
+static void realtek_smi_start(struct realtek_smi *smi)
+{
+ /* Set GPIO pins to output mode, with initial state:
+ * SCK = 0, SDA = 1
+ */
+ gpiod_direction_output(smi->mdc, 0);
+ gpiod_direction_output(smi->mdio, 1);
+ realtek_smi_clk_delay(smi);
+
+ /* CLK 1: 0 -> 1, 1 -> 0 */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+
+ /* CLK 2: */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 1);
+}
+
+static void realtek_smi_stop(struct realtek_smi *smi)
+{
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 0);
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+
+ /* Add a click */
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+
+ /* Set GPIO pins to input mode */
+ gpiod_direction_input(smi->mdio);
+ gpiod_direction_input(smi->mdc);
+}
+
+static void realtek_smi_write_bits(struct realtek_smi *smi, u32 data, u32 len)
+{
+ for (; len > 0; len--) {
+ realtek_smi_clk_delay(smi);
+
+ /* Prepare data */
+ gpiod_set_value(smi->mdio, !!(data & (1 << (len - 1))));
+ realtek_smi_clk_delay(smi);
+
+ /* Clocking */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ }
+}
+
+static void realtek_smi_read_bits(struct realtek_smi *smi, u32 len, u32 *data)
+{
+ gpiod_direction_input(smi->mdio);
+
+ for (*data = 0; len > 0; len--) {
+ u32 u;
+
+ realtek_smi_clk_delay(smi);
+
+ /* Clocking */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ u = !!gpiod_get_value(smi->mdio);
+ gpiod_set_value(smi->mdc, 0);
+
+ *data |= (u << (len - 1));
+ }
+
+ gpiod_direction_output(smi->mdio, 0);
+}
+
+static int realtek_smi_wait_for_ack(struct realtek_smi *smi)
+{
+ int retry_cnt;
+
+ retry_cnt = 0;
+ do {
+ u32 ack;
+
+ realtek_smi_read_bits(smi, 1, &ack);
+ if (ack == 0)
+ break;
+
+ if (++retry_cnt > REALTEK_SMI_ACK_RETRY_COUNT) {
+ dev_err(smi->dev, "ACK timeout\n");
+ return -ETIMEDOUT;
+ }
+ } while (1);
+
+ return 0;
+}
+
+static int realtek_smi_write_byte(struct realtek_smi *smi, u8 data)
+{
+ realtek_smi_write_bits(smi, data, 8);
+ return realtek_smi_wait_for_ack(smi);
+}
+
+static int realtek_smi_write_byte_noack(struct realtek_smi *smi, u8 data)
+{
+ realtek_smi_write_bits(smi, data, 8);
+ return 0;
+}
+
+static int realtek_smi_read_byte0(struct realtek_smi *smi, u8 *data)
+{
+ u32 t;
+
+ /* Read data */
+ realtek_smi_read_bits(smi, 8, &t);
+ *data = (t & 0xff);
+
+ /* Send an ACK */
+ realtek_smi_write_bits(smi, 0x00, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_byte1(struct realtek_smi *smi, u8 *data)
+{
+ u32 t;
+
+ /* Read data */
+ realtek_smi_read_bits(smi, 8, &t);
+ *data = (t & 0xff);
+
+ /* Send an ACK */
+ realtek_smi_write_bits(smi, 0x01, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_reg(struct realtek_smi *smi, u32 addr, u32 *data)
+{
+ unsigned long flags;
+ u8 lo = 0;
+ u8 hi = 0;
+ int ret;
+
+ spin_lock_irqsave(&smi->lock, flags);
+
+ realtek_smi_start(smi);
+
+ /* Send READ command */
+ ret = realtek_smi_write_byte(smi, smi->cmd_read);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[7:0] */
+ ret = realtek_smi_write_byte(smi, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[15:8] */
+ ret = realtek_smi_write_byte(smi, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* Read DATA[7:0] */
+ realtek_smi_read_byte0(smi, &lo);
+ /* Read DATA[15:8] */
+ realtek_smi_read_byte1(smi, &hi);
+
+ *data = ((u32)lo) | (((u32)hi) << 8);
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(smi);
+ spin_unlock_irqrestore(&smi->lock, flags);
+
+ return ret;
+}
+
+static int realtek_smi_write_reg(struct realtek_smi *smi,
+ u32 addr, u32 data, bool ack)
+{
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&smi->lock, flags);
+
+ realtek_smi_start(smi);
+
+ /* Send WRITE command */
+ ret = realtek_smi_write_byte(smi, smi->cmd_write);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[7:0] */
+ ret = realtek_smi_write_byte(smi, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[15:8] */
+ ret = realtek_smi_write_byte(smi, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* Write DATA[7:0] */
+ ret = realtek_smi_write_byte(smi, data & 0xff);
+ if (ret)
+ goto out;
+
+ /* Write DATA[15:8] */
+ if (ack)
+ ret = realtek_smi_write_byte(smi, data >> 8);
+ else
+ ret = realtek_smi_write_byte_noack(smi, data >> 8);
+ if (ret)
+ goto out;
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(smi);
+ spin_unlock_irqrestore(&smi->lock, flags);
+
+ return ret;
+}
+
+/* There is one single case when we need to use this accessor and that
+ * is when issueing soft reset. Since the device reset as soon as we write
+ * that bit, no ACK will come back for natural reasons.
+ */
+int realtek_smi_write_reg_noack(struct realtek_smi *smi, u32 addr,
+ u32 data)
+{
+ return realtek_smi_write_reg(smi, addr, data, false);
+}
+EXPORT_SYMBOL_GPL(realtek_smi_write_reg_noack);
+
+/* Regmap accessors */
+
+static int realtek_smi_write(void *ctx, u32 reg, u32 val)
+{
+ struct realtek_smi *smi = ctx;
+
+ return realtek_smi_write_reg(smi, reg, val, true);
+}
+
+static int realtek_smi_read(void *ctx, u32 reg, u32 *val)
+{
+ struct realtek_smi *smi = ctx;
+
+ return realtek_smi_read_reg(smi, reg, val);
+}
+
+static const struct regmap_config realtek_smi_mdio_regmap_config = {
+ .reg_bits = 10, /* A4..A0 R4..R0 */
+ .val_bits = 16,
+ .reg_stride = 1,
+ /* PHY regs are at 0x8000 */
+ .max_register = 0xffff,
+ .reg_format_endian = REGMAP_ENDIAN_BIG,
+ .reg_read = realtek_smi_read,
+ .reg_write = realtek_smi_write,
+ .cache_type = REGCACHE_NONE,
+};
+
+static int realtek_smi_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+ struct realtek_smi *smi = bus->priv;
+
+ return smi->ops->phy_read(smi, addr, regnum);
+}
+
+static int realtek_smi_mdio_write(struct mii_bus *bus, int addr, int regnum,
+ u16 val)
+{
+ struct realtek_smi *smi = bus->priv;
+
+ return smi->ops->phy_write(smi, addr, regnum, val);
+}
+
+int realtek_smi_setup_mdio(struct realtek_smi *smi)
+{
+ struct device_node *mdio_np;
+ int ret;
+
+ mdio_np = of_find_compatible_node(smi->dev->of_node, NULL,
+ "realtek,smi-mdio");
+ if (!mdio_np) {
+ dev_err(smi->dev, "no MDIO bus node\n");
+ return -ENODEV;
+ }
+
+ smi->slave_mii_bus = devm_mdiobus_alloc(smi->dev);
+ if (!smi->slave_mii_bus)
+ return -ENOMEM;
+ smi->slave_mii_bus->priv = smi;
+ smi->slave_mii_bus->name = "SMI slave MII";
+ smi->slave_mii_bus->read = realtek_smi_mdio_read;
+ smi->slave_mii_bus->write = realtek_smi_mdio_write;
+ snprintf(smi->slave_mii_bus->id, MII_BUS_ID_SIZE, "SMI-%d",
+ smi->ds->index);
+ smi->slave_mii_bus->dev.of_node = mdio_np;
+ smi->slave_mii_bus->parent = smi->dev;
+ smi->ds->slave_mii_bus = smi->slave_mii_bus;
+
+ ret = of_mdiobus_register(smi->slave_mii_bus, mdio_np);
+ if (ret) {
+ dev_err(smi->dev, "unable to register MDIO bus %s\n",
+ smi->slave_mii_bus->id);
+ of_node_put(mdio_np);
+ }
+
+ return 0;
+}
+
+static int realtek_smi_probe(struct platform_device *pdev)
+{
+ const struct realtek_smi_variant *var;
+ struct device *dev = &pdev->dev;
+ struct realtek_smi *smi;
+ struct device_node *np;
+ int ret;
+
+ var = of_device_get_match_data(dev);
+ np = dev->of_node;
+
+ smi = devm_kzalloc(dev, sizeof(*smi), GFP_KERNEL);
+ if (!smi)
+ return -ENOMEM;
+ smi->map = devm_regmap_init(dev, NULL, smi,
+ &realtek_smi_mdio_regmap_config);
+ if (IS_ERR(smi->map)) {
+ ret = PTR_ERR(smi->map);
+ dev_err(dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ /* Link forward and backward */
+ smi->dev = dev;
+ smi->clk_delay = var->clk_delay;
+ smi->cmd_read = var->cmd_read;
+ smi->cmd_write = var->cmd_write;
+ smi->ops = var->ops;
+
+ dev_set_drvdata(dev, smi);
+ spin_lock_init(&smi->lock);
+
+ /* TODO: if power is software controlled, set up any regulators here */
+
+ /* Assert then deassert RESET */
+ smi->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(smi->reset)) {
+ dev_err(dev, "failed to get RESET GPIO\n");
+ return PTR_ERR(smi->reset);
+ }
+ msleep(REALTEK_SMI_HW_STOP_DELAY);
+ gpiod_set_value(smi->reset, 0);
+ msleep(REALTEK_SMI_HW_START_DELAY);
+ dev_info(dev, "deasserted RESET\n");
+
+ /* Fetch MDIO pins */
+ smi->mdc = devm_gpiod_get_optional(dev, "mdc", GPIOD_OUT_LOW);
+ if (IS_ERR(smi->mdc))
+ return PTR_ERR(smi->mdc);
+ smi->mdio = devm_gpiod_get_optional(dev, "mdio", GPIOD_OUT_LOW);
+ if (IS_ERR(smi->mdio))
+ return PTR_ERR(smi->mdio);
+
+ smi->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
+
+ ret = smi->ops->detect(smi);
+ if (ret) {
+ dev_err(dev, "unable to detect switch\n");
+ return ret;
+ }
+
+ smi->ds = dsa_switch_alloc(dev, smi->num_ports);
+ if (!smi->ds)
+ return -ENOMEM;
+ smi->ds->priv = smi;
+
+ smi->ds->ops = var->ds_ops;
+ ret = dsa_register_switch(smi->ds);
+ if (ret) {
+ dev_err(dev, "unable to register switch ret = %d\n", ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int realtek_smi_remove(struct platform_device *pdev)
+{
+ struct realtek_smi *smi = dev_get_drvdata(&pdev->dev);
+
+ dsa_unregister_switch(smi->ds);
+ gpiod_set_value(smi->reset, 1);
+
+ return 0;
+}
+
+static const struct of_device_id realtek_smi_of_match[] = {
+ {
+ .compatible = "realtek,rtl8366rb",
+ .data = &rtl8366rb_variant,
+ },
+ {
+ /* FIXME: add support for RTL8366S and more */
+ .compatible = "realtek,rtl8366s",
+ .data = NULL,
+ },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, realtek_smi_of_match);
+
+static struct platform_driver realtek_smi_driver = {
+ .driver = {
+ .name = "realtek-smi",
+ .of_match_table = of_match_ptr(realtek_smi_of_match),
+ },
+ .probe = realtek_smi_probe,
+ .remove = realtek_smi_remove,
+};
+module_platform_driver(realtek_smi_driver);
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI library helpers for the RTL8366x variants
+ * RTL8366RB and RTL8366S
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ */
+#include <linux/if_bridge.h>
+#include <net/dsa.h>
+
+#include "realtek-smi.h"
+
+int rtl8366_mc_is_used(struct realtek_smi *smi, int mc_index, int *used)
+{
+ int ret;
+ int i;
+
+ *used = 0;
+ for (i = 0; i < smi->num_ports; i++) {
+ int index = 0;
+
+ ret = smi->ops->get_mc_index(smi, i, &index);
+ if (ret)
+ return ret;
+
+ if (mc_index == index) {
+ *used = 1;
+ break;
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_mc_is_used);
+
+int rtl8366_set_vlan(struct realtek_smi *smi, int vid, u32 member,
+ u32 untag, u32 fid)
+{
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+ int i;
+
+ /* Update the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlan4k.member = member;
+ vlan4k.untag = untag;
+ vlan4k.fid = fid;
+ ret = smi->ops->set_vlan_4k(smi, &vlan4k);
+ if (ret)
+ return ret;
+
+ /* Try to find an existing MC entry for this VID */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ struct rtl8366_vlan_mc vlanmc;
+
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ /* update the MC entry */
+ vlanmc.member = member;
+ vlanmc.untag = untag;
+ vlanmc.fid = fid;
+
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ break;
+ }
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(rtl8366_set_vlan);
+
+int rtl8366_get_pvid(struct realtek_smi *smi, int port, int *val)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ int ret;
+ int index;
+
+ ret = smi->ops->get_mc_index(smi, port, &index);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->get_vlan_mc(smi, index, &vlanmc);
+ if (ret)
+ return ret;
+
+ *val = vlanmc.vid;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_pvid);
+
+int rtl8366_set_pvid(struct realtek_smi *smi, unsigned int port,
+ unsigned int vid)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+ int i;
+
+ /* Try to find an existing MC entry for this VID */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ /* We have no MC entry for this VID, try to find an empty one */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vlanmc.vid == 0 && vlanmc.member == 0) {
+ /* Update the entry from the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlanmc.vid = vid;
+ vlanmc.member = vlan4k.member;
+ vlanmc.untag = vlan4k.untag;
+ vlanmc.fid = vlan4k.fid;
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ /* MC table is full, try to find an unused entry and replace it */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ int used;
+
+ ret = rtl8366_mc_is_used(smi, i, &used);
+ if (ret)
+ return ret;
+
+ if (!used) {
+ /* Update the entry from the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlanmc.vid = vid;
+ vlanmc.member = vlan4k.member;
+ vlanmc.untag = vlan4k.untag;
+ vlanmc.fid = vlan4k.fid;
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ dev_err(smi->dev,
+ "all VLAN member configurations are in use\n");
+
+ return -ENOSPC;
+}
+EXPORT_SYMBOL_GPL(rtl8366_set_pvid);
+
+int rtl8366_enable_vlan4k(struct realtek_smi *smi, bool enable)
+{
+ int ret;
+
+ /* To enable 4k VLAN, ordinary VLAN must be enabled first,
+ * but if we disable 4k VLAN it is fine to leave ordinary
+ * VLAN enabled.
+ */
+ if (enable) {
+ /* Make sure VLAN is ON */
+ ret = smi->ops->enable_vlan(smi, true);
+ if (ret)
+ return ret;
+
+ smi->vlan_enabled = true;
+ }
+
+ ret = smi->ops->enable_vlan4k(smi, enable);
+ if (ret)
+ return ret;
+
+ smi->vlan4k_enabled = enable;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_enable_vlan4k);
+
+int rtl8366_enable_vlan(struct realtek_smi *smi, bool enable)
+{
+ int ret;
+
+ ret = smi->ops->enable_vlan(smi, enable);
+ if (ret)
+ return ret;
+
+ smi->vlan_enabled = enable;
+
+ /* If we turn VLAN off, make sure that we turn off
+ * 4k VLAN as well, if that happened to be on.
+ */
+ if (!enable) {
+ smi->vlan4k_enabled = false;
+ ret = smi->ops->enable_vlan4k(smi, false);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(rtl8366_enable_vlan);
+
+int rtl8366_reset_vlan(struct realtek_smi *smi)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+ int i;
+
+ rtl8366_enable_vlan(smi, false);
+ rtl8366_enable_vlan4k(smi, false);
+
+ /* Clear the 16 VLAN member configurations */
+ vlanmc.vid = 0;
+ vlanmc.priority = 0;
+ vlanmc.member = 0;
+ vlanmc.untag = 0;
+ vlanmc.fid = 0;
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_reset_vlan);
+
+int rtl8366_init_vlan(struct realtek_smi *smi)
+{
+ int port;
+ int ret;
+
+ ret = rtl8366_reset_vlan(smi);
+ if (ret)
+ return ret;
+
+ /* Loop over the available ports, for each port, associate
+ * it with the VLAN (port+1)
+ */
+ for (port = 0; port < smi->num_ports; port++) {
+ u32 mask;
+
+ if (port == smi->cpu_port)
+ /* For the CPU port, make all ports members of this
+ * VLAN.
+ */
+ mask = GENMASK(smi->num_ports - 1, 0);
+ else
+ /* For all other ports, enable itself plus the
+ * CPU port.
+ */
+ mask = BIT(port) | BIT(smi->cpu_port);
+
+ /* For each port, set the port as member of VLAN (port+1)
+ * and untagged, except for the CPU port: the CPU port (5) is
+ * member of VLAN 6 and so are ALL the other ports as well.
+ * Use filter 0 (no filter).
+ */
+ dev_info(smi->dev, "VLAN%d port mask for port %d, %08x\n",
+ (port + 1), port, mask);
+ ret = rtl8366_set_vlan(smi, (port + 1), mask, mask, 0);
+ if (ret)
+ return ret;
+
+ dev_info(smi->dev, "VLAN%d port %d, PVID set to %d\n",
+ (port + 1), port, (port + 1));
+ ret = rtl8366_set_pvid(smi, port, (port + 1));
+ if (ret)
+ return ret;
+ }
+
+ return rtl8366_enable_vlan(smi, true);
+}
+EXPORT_SYMBOL_GPL(rtl8366_init_vlan);
+
+int rtl8366_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return -EINVAL;
+
+ dev_info(smi->dev, "%s filtering on port %d\n",
+ vlan_filtering ? "enable" : "disable",
+ port);
+
+ /* TODO:
+ * The hardware support filter ID (FID) 0..7, I have no clue how to
+ * support this in the driver when the callback only says on/off.
+ */
+ ret = smi->ops->get_vlan_4k(smi, port, &vlan4k);
+ if (ret)
+ return ret;
+
+ /* Just set the filter to FID 1 for now then */
+ ret = rtl8366_set_vlan(smi, port,
+ vlan4k.member,
+ vlan4k.untag,
+ 1);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_filtering);
+
+int rtl8366_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return -EINVAL;
+
+ dev_info(smi->dev, "prepare VLANs %04x..%04x\n",
+ vlan->vid_begin, vlan->vid_end);
+
+ /* Enable VLAN in the hardware
+ * FIXME: what's with this 4k business?
+ * Just rtl8366_enable_vlan() seems inconclusive.
+ */
+ ret = rtl8366_enable_vlan4k(smi, true);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_prepare);
+
+void rtl8366_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ bool untagged = !!(vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED);
+ bool pvid = !!(vlan->flags & BRIDGE_VLAN_INFO_PVID);
+ struct realtek_smi *smi = ds->priv;
+ u32 member = 0;
+ u32 untag = 0;
+ u16 vid;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return;
+
+ dev_info(smi->dev, "add VLAN on port %d, %s, %s\n",
+ port,
+ untagged ? "untagged" : "tagged",
+ pvid ? " PVID" : "no PVID");
+
+ if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port))
+ dev_err(smi->dev, "port is DSA or CPU port\n");
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ int pvid_val = 0;
+
+ dev_info(smi->dev, "add VLAN %04x\n", vid);
+ member |= BIT(port);
+
+ if (untagged)
+ untag |= BIT(port);
+
+ /* To ensure that we have a valid MC entry for this VLAN,
+ * initialize the port VLAN ID here.
+ */
+ ret = rtl8366_get_pvid(smi, port, &pvid_val);
+ if (ret < 0) {
+ dev_err(smi->dev, "could not lookup PVID for port %d\n",
+ port);
+ return;
+ }
+ if (pvid_val == 0) {
+ ret = rtl8366_set_pvid(smi, port, vid);
+ if (ret < 0)
+ return;
+ }
+ }
+
+ ret = rtl8366_set_vlan(smi, port, member, untag, 0);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to set up VLAN %04x",
+ vid);
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_add);
+
+int rtl8366_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct realtek_smi *smi = ds->priv;
+ u16 vid;
+ int ret;
+
+ dev_info(smi->dev, "del VLAN on port %d\n", port);
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ int i;
+
+ dev_info(smi->dev, "del VLAN %04x\n", vid);
+
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ struct rtl8366_vlan_mc vlanmc;
+
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ /* clear VLAN member configurations */
+ vlanmc.vid = 0;
+ vlanmc.priority = 0;
+ vlanmc.member = 0;
+ vlanmc.untag = 0;
+ vlanmc.fid = 0;
+
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to remove VLAN %04x\n",
+ vid);
+ return ret;
+ }
+ break;
+ }
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_del);
+
+void rtl8366_get_strings(struct dsa_switch *ds, int port, u32 stringset,
+ uint8_t *data)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8366_mib_counter *mib;
+ int i;
+
+ if (port >= smi->num_ports)
+ return;
+
+ for (i = 0; i < smi->num_mib_counters; i++) {
+ mib = &smi->mib_counters[i];
+ strncpy(data + i * ETH_GSTRING_LEN,
+ mib->name, ETH_GSTRING_LEN);
+ }
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_strings);
+
+int rtl8366_get_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ /* We only support SS_STATS */
+ if (sset != ETH_SS_STATS)
+ return 0;
+ if (port >= smi->num_ports)
+ return -EINVAL;
+
+ return smi->num_mib_counters;
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_sset_count);
+
+void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data)
+{
+ struct realtek_smi *smi = ds->priv;
+ int i;
+ int ret;
+
+ if (port >= smi->num_ports)
+ return;
+
+ for (i = 0; i < smi->num_mib_counters; i++) {
+ struct rtl8366_mib_counter *mib;
+ u64 mibvalue = 0;
+
+ mib = &smi->mib_counters[i];
+ ret = smi->ops->get_mib_counter(smi, port, mib, &mibvalue);
+ if (ret) {
+ dev_err(smi->dev, "error reading MIB counter %s\n",
+ mib->name);
+ }
+ data[i] = mibvalue;
+ }
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_ethtool_stats);
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI subdriver for the Realtek RTL8366RB ethernet switch
+ *
+ * This is a sparsely documented chip, the only viable documentation seems
+ * to be a patched up code drop from the vendor that appear in various
+ * GPL source trees.
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/etherdevice.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+
+#include "realtek-smi.h"
+
+#define RTL8366RB_PORT_NUM_CPU 5
+#define RTL8366RB_NUM_PORTS 6
+#define RTL8366RB_PHY_NO_MAX 4
+#define RTL8366RB_PHY_ADDR_MAX 31
+
+/* Switch Global Configuration register */
+#define RTL8366RB_SGCR 0x0000
+#define RTL8366RB_SGCR_EN_BC_STORM_CTRL BIT(0)
+#define RTL8366RB_SGCR_MAX_LENGTH(a) ((a) << 4)
+#define RTL8366RB_SGCR_MAX_LENGTH_MASK RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_MAX_LENGTH_1522 RTL8366RB_SGCR_MAX_LENGTH(0x0)
+#define RTL8366RB_SGCR_MAX_LENGTH_1536 RTL8366RB_SGCR_MAX_LENGTH(0x1)
+#define RTL8366RB_SGCR_MAX_LENGTH_1552 RTL8366RB_SGCR_MAX_LENGTH(0x2)
+#define RTL8366RB_SGCR_MAX_LENGTH_9216 RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_EN_VLAN BIT(13)
+#define RTL8366RB_SGCR_EN_VLAN_4KTB BIT(14)
+
+/* Port Enable Control register */
+#define RTL8366RB_PECR 0x0001
+
+/* Switch Security Control registers */
+#define RTL8366RB_SSCR0 0x0002
+#define RTL8366RB_SSCR1 0x0003
+#define RTL8366RB_SSCR2 0x0004
+#define RTL8366RB_SSCR2_DROP_UNKNOWN_DA BIT(0)
+
+/* Port Mirror Control Register */
+#define RTL8366RB_PMCR 0x0007
+#define RTL8366RB_PMCR_SOURCE_PORT(a) (a)
+#define RTL8366RB_PMCR_SOURCE_PORT_MASK 0x000f
+#define RTL8366RB_PMCR_MONITOR_PORT(a) ((a) << 4)
+#define RTL8366RB_PMCR_MONITOR_PORT_MASK 0x00f0
+#define RTL8366RB_PMCR_MIRROR_RX BIT(8)
+#define RTL8366RB_PMCR_MIRROR_TX BIT(9)
+#define RTL8366RB_PMCR_MIRROR_SPC BIT(10)
+#define RTL8366RB_PMCR_MIRROR_ISO BIT(11)
+
+/* bits 0..7 = port 0, bits 8..15 = port 1 */
+#define RTL8366RB_PAACR0 0x0010
+/* bits 0..7 = port 2, bits 8..15 = port 3 */
+#define RTL8366RB_PAACR1 0x0011
+/* bits 0..7 = port 4, bits 8..15 = port 5 */
+#define RTL8366RB_PAACR2 0x0012
+#define RTL8366RB_PAACR_SPEED_10M 0
+#define RTL8366RB_PAACR_SPEED_100M 1
+#define RTL8366RB_PAACR_SPEED_1000M 2
+#define RTL8366RB_PAACR_FULL_DUPLEX BIT(2)
+#define RTL8366RB_PAACR_LINK_UP BIT(4)
+#define RTL8366RB_PAACR_TX_PAUSE BIT(5)
+#define RTL8366RB_PAACR_RX_PAUSE BIT(6)
+#define RTL8366RB_PAACR_AN BIT(7)
+
+#define RTL8366RB_PAACR_CPU_PORT (RTL8366RB_PAACR_SPEED_1000M | \
+ RTL8366RB_PAACR_FULL_DUPLEX | \
+ RTL8366RB_PAACR_LINK_UP | \
+ RTL8366RB_PAACR_TX_PAUSE | \
+ RTL8366RB_PAACR_RX_PAUSE)
+
+/* bits 0..7 = port 0, bits 8..15 = port 1 */
+#define RTL8366RB_PSTAT0 0x0014
+/* bits 0..7 = port 2, bits 8..15 = port 3 */
+#define RTL8366RB_PSTAT1 0x0015
+/* bits 0..7 = port 4, bits 8..15 = port 5 */
+#define RTL8366RB_PSTAT2 0x0016
+
+#define RTL8366RB_POWER_SAVING_REG 0x0021
+
+/* CPU port control reg */
+#define RTL8368RB_CPU_CTRL_REG 0x0061
+#define RTL8368RB_CPU_PORTS_MSK 0x00FF
+/* Enables inserting custom tag length/type 0x8899 */
+#define RTL8368RB_CPU_INSTAG BIT(15)
+
+#define RTL8366RB_SMAR0 0x0070 /* bits 0..15 */
+#define RTL8366RB_SMAR1 0x0071 /* bits 16..31 */
+#define RTL8366RB_SMAR2 0x0072 /* bits 32..47 */
+
+#define RTL8366RB_RESET_CTRL_REG 0x0100
+#define RTL8366RB_CHIP_CTRL_RESET_HW BIT(0)
+#define RTL8366RB_CHIP_CTRL_RESET_SW BIT(1)
+
+#define RTL8366RB_CHIP_ID_REG 0x0509
+#define RTL8366RB_CHIP_ID_8366 0x5937
+#define RTL8366RB_CHIP_VERSION_CTRL_REG 0x050A
+#define RTL8366RB_CHIP_VERSION_MASK 0xf
+
+/* PHY registers control */
+#define RTL8366RB_PHY_ACCESS_CTRL_REG 0x8000
+#define RTL8366RB_PHY_CTRL_READ BIT(0)
+#define RTL8366RB_PHY_CTRL_WRITE 0
+#define RTL8366RB_PHY_ACCESS_BUSY_REG 0x8001
+#define RTL8366RB_PHY_INT_BUSY BIT(0)
+#define RTL8366RB_PHY_EXT_BUSY BIT(4)
+#define RTL8366RB_PHY_ACCESS_DATA_REG 0x8002
+#define RTL8366RB_PHY_EXT_CTRL_REG 0x8010
+#define RTL8366RB_PHY_EXT_WRDATA_REG 0x8011
+#define RTL8366RB_PHY_EXT_RDDATA_REG 0x8012
+
+#define RTL8366RB_PHY_REG_MASK 0x1f
+#define RTL8366RB_PHY_PAGE_OFFSET 5
+#define RTL8366RB_PHY_PAGE_MASK (0xf << 5)
+#define RTL8366RB_PHY_NO_OFFSET 9
+#define RTL8366RB_PHY_NO_MASK (0x1f << 9)
+
+#define RTL8366RB_VLAN_INGRESS_CTRL2_REG 0x037f
+
+/* LED control registers */
+#define RTL8366RB_LED_BLINKRATE_REG 0x0430
+#define RTL8366RB_LED_BLINKRATE_MASK 0x0007
+#define RTL8366RB_LED_BLINKRATE_28MS 0x0000
+#define RTL8366RB_LED_BLINKRATE_56MS 0x0001
+#define RTL8366RB_LED_BLINKRATE_84MS 0x0002
+#define RTL8366RB_LED_BLINKRATE_111MS 0x0003
+#define RTL8366RB_LED_BLINKRATE_222MS 0x0004
+#define RTL8366RB_LED_BLINKRATE_446MS 0x0005
+
+#define RTL8366RB_LED_CTRL_REG 0x0431
+#define RTL8366RB_LED_OFF 0x0
+#define RTL8366RB_LED_DUP_COL 0x1
+#define RTL8366RB_LED_LINK_ACT 0x2
+#define RTL8366RB_LED_SPD1000 0x3
+#define RTL8366RB_LED_SPD100 0x4
+#define RTL8366RB_LED_SPD10 0x5
+#define RTL8366RB_LED_SPD1000_ACT 0x6
+#define RTL8366RB_LED_SPD100_ACT 0x7
+#define RTL8366RB_LED_SPD10_ACT 0x8
+#define RTL8366RB_LED_SPD100_10_ACT 0x9
+#define RTL8366RB_LED_FIBER 0xa
+#define RTL8366RB_LED_AN_FAULT 0xb
+#define RTL8366RB_LED_LINK_RX 0xc
+#define RTL8366RB_LED_LINK_TX 0xd
+#define RTL8366RB_LED_MASTER 0xe
+#define RTL8366RB_LED_FORCE 0xf
+#define RTL8366RB_LED_0_1_CTRL_REG 0x0432
+#define RTL8366RB_LED_1_OFFSET 6
+#define RTL8366RB_LED_2_3_CTRL_REG 0x0433
+#define RTL8366RB_LED_3_OFFSET 6
+
+#define RTL8366RB_MIB_COUNT 33
+#define RTL8366RB_GLOBAL_MIB_COUNT 1
+#define RTL8366RB_MIB_COUNTER_PORT_OFFSET 0x0050
+#define RTL8366RB_MIB_COUNTER_BASE 0x1000
+#define RTL8366RB_MIB_CTRL_REG 0x13F0
+#define RTL8366RB_MIB_CTRL_USER_MASK 0x0FFC
+#define RTL8366RB_MIB_CTRL_BUSY_MASK BIT(0)
+#define RTL8366RB_MIB_CTRL_RESET_MASK BIT(1)
+#define RTL8366RB_MIB_CTRL_PORT_RESET(_p) BIT(2 + (_p))
+#define RTL8366RB_MIB_CTRL_GLOBAL_RESET BIT(11)
+
+#define RTL8366RB_PORT_VLAN_CTRL_BASE 0x0063
+#define RTL8366RB_PORT_VLAN_CTRL_REG(_p) \
+ (RTL8366RB_PORT_VLAN_CTRL_BASE + (_p) / 4)
+#define RTL8366RB_PORT_VLAN_CTRL_MASK 0xf
+#define RTL8366RB_PORT_VLAN_CTRL_SHIFT(_p) (4 * ((_p) % 4))
+
+#define RTL8366RB_VLAN_TABLE_READ_BASE 0x018C
+#define RTL8366RB_VLAN_TABLE_WRITE_BASE 0x0185
+
+#define RTL8366RB_TABLE_ACCESS_CTRL_REG 0x0180
+#define RTL8366RB_TABLE_VLAN_READ_CTRL 0x0E01
+#define RTL8366RB_TABLE_VLAN_WRITE_CTRL 0x0F01
+
+#define RTL8366RB_VLAN_MC_BASE(_x) (0x0020 + (_x) * 3)
+
+#define RTL8366RB_PORT_LINK_STATUS_BASE 0x0014
+#define RTL8366RB_PORT_STATUS_SPEED_MASK 0x0003
+#define RTL8366RB_PORT_STATUS_DUPLEX_MASK 0x0004
+#define RTL8366RB_PORT_STATUS_LINK_MASK 0x0010
+#define RTL8366RB_PORT_STATUS_TXPAUSE_MASK 0x0020
+#define RTL8366RB_PORT_STATUS_RXPAUSE_MASK 0x0040
+#define RTL8366RB_PORT_STATUS_AN_MASK 0x0080
+
+#define RTL8366RB_NUM_VLANS 16
+#define RTL8366RB_NUM_LEDGROUPS 4
+#define RTL8366RB_NUM_VIDS 4096
+#define RTL8366RB_PRIORITYMAX 7
+#define RTL8366RB_FIDMAX 7
+
+#define RTL8366RB_PORT_1 BIT(0) /* In userspace port 0 */
+#define RTL8366RB_PORT_2 BIT(1) /* In userspace port 1 */
+#define RTL8366RB_PORT_3 BIT(2) /* In userspace port 2 */
+#define RTL8366RB_PORT_4 BIT(3) /* In userspace port 3 */
+#define RTL8366RB_PORT_5 BIT(4) /* In userspace port 4 */
+
+#define RTL8366RB_PORT_CPU BIT(5) /* CPU port */
+
+#define RTL8366RB_PORT_ALL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5 | \
+ RTL8366RB_PORT_CPU)
+
+#define RTL8366RB_PORT_ALL_BUT_CPU (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5)
+
+#define RTL8366RB_PORT_ALL_EXTERNAL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4)
+
+#define RTL8366RB_PORT_ALL_INTERNAL RTL8366RB_PORT_CPU
+
+/* First configuration word per member config, VID and prio */
+#define RTL8366RB_VLAN_VID_MASK 0xfff
+#define RTL8366RB_VLAN_PRIORITY_SHIFT 12
+#define RTL8366RB_VLAN_PRIORITY_MASK 0x7
+/* Second configuration word per member config, member and untagged */
+#define RTL8366RB_VLAN_UNTAG_SHIFT 8
+#define RTL8366RB_VLAN_UNTAG_MASK 0xff
+#define RTL8366RB_VLAN_MEMBER_MASK 0xff
+/* Third config word per member config, STAG currently unused */
+#define RTL8366RB_VLAN_STAG_MBR_MASK 0xff
+#define RTL8366RB_VLAN_STAG_MBR_SHIFT 8
+#define RTL8366RB_VLAN_STAG_IDX_MASK 0x7
+#define RTL8366RB_VLAN_STAG_IDX_SHIFT 5
+#define RTL8366RB_VLAN_FID_MASK 0x7
+
+/* Port ingress bandwidth control */
+#define RTL8366RB_IB_BASE 0x0200
+#define RTL8366RB_IB_REG(pnum) (RTL8366RB_IB_BASE + (pnum))
+#define RTL8366RB_IB_BDTH_MASK 0x3fff
+#define RTL8366RB_IB_PREIFG BIT(14)
+
+/* Port egress bandwidth control */
+#define RTL8366RB_EB_BASE 0x02d1
+#define RTL8366RB_EB_REG(pnum) (RTL8366RB_EB_BASE + (pnum))
+#define RTL8366RB_EB_BDTH_MASK 0x3fff
+#define RTL8366RB_EB_PREIFG_REG 0x02f8
+#define RTL8366RB_EB_PREIFG BIT(9)
+
+#define RTL8366RB_BDTH_SW_MAX 1048512 /* 1048576? */
+#define RTL8366RB_BDTH_UNIT 64
+#define RTL8366RB_BDTH_REG_DEFAULT 16383
+
+/* QOS */
+#define RTL8366RB_QOS BIT(15)
+/* Include/Exclude Preamble and IFG (20 bytes). 0:Exclude, 1:Include. */
+#define RTL8366RB_QOS_DEFAULT_PREIFG 1
+
+/* Interrupt handling */
+#define RTL8366RB_INTERRUPT_CONTROL_REG 0x0440
+#define RTL8366RB_INTERRUPT_POLARITY BIT(0)
+#define RTL8366RB_P4_RGMII_LED BIT(2)
+#define RTL8366RB_INTERRUPT_MASK_REG 0x0441
+#define RTL8366RB_INTERRUPT_LINK_CHGALL GENMASK(11, 0)
+#define RTL8366RB_INTERRUPT_ACLEXCEED BIT(8)
+#define RTL8366RB_INTERRUPT_STORMEXCEED BIT(9)
+#define RTL8366RB_INTERRUPT_P4_FIBER BIT(12)
+#define RTL8366RB_INTERRUPT_P4_UTP BIT(13)
+#define RTL8366RB_INTERRUPT_VALID (RTL8366RB_INTERRUPT_LINK_CHGALL | \
+ RTL8366RB_INTERRUPT_ACLEXCEED | \
+ RTL8366RB_INTERRUPT_STORMEXCEED | \
+ RTL8366RB_INTERRUPT_P4_FIBER | \
+ RTL8366RB_INTERRUPT_P4_UTP)
+#define RTL8366RB_INTERRUPT_STATUS_REG 0x0442
+#define RTL8366RB_NUM_INTERRUPT 14 /* 0..13 */
+
+/* bits 0..5 enable force when cleared */
+#define RTL8366RB_MAC_FORCE_CTRL_REG 0x0F11
+
+#define RTL8366RB_OAM_PARSER_REG 0x0F14
+#define RTL8366RB_OAM_MULTIPLEXER_REG 0x0F15
+
+#define RTL8366RB_GREEN_FEATURE_REG 0x0F51
+#define RTL8366RB_GREEN_FEATURE_MSK 0x0007
+#define RTL8366RB_GREEN_FEATURE_TX BIT(0)
+#define RTL8366RB_GREEN_FEATURE_RX BIT(2)
+
+static struct rtl8366_mib_counter rtl8366rb_mib_counters[] = {
+ { 0, 0, 4, "IfInOctets" },
+ { 0, 4, 4, "EtherStatsOctets" },
+ { 0, 8, 2, "EtherStatsUnderSizePkts" },
+ { 0, 10, 2, "EtherFragments" },
+ { 0, 12, 2, "EtherStatsPkts64Octets" },
+ { 0, 14, 2, "EtherStatsPkts65to127Octets" },
+ { 0, 16, 2, "EtherStatsPkts128to255Octets" },
+ { 0, 18, 2, "EtherStatsPkts256to511Octets" },
+ { 0, 20, 2, "EtherStatsPkts512to1023Octets" },
+ { 0, 22, 2, "EtherStatsPkts1024to1518Octets" },
+ { 0, 24, 2, "EtherOversizeStats" },
+ { 0, 26, 2, "EtherStatsJabbers" },
+ { 0, 28, 2, "IfInUcastPkts" },
+ { 0, 30, 2, "EtherStatsMulticastPkts" },
+ { 0, 32, 2, "EtherStatsBroadcastPkts" },
+ { 0, 34, 2, "EtherStatsDropEvents" },
+ { 0, 36, 2, "Dot3StatsFCSErrors" },
+ { 0, 38, 2, "Dot3StatsSymbolErrors" },
+ { 0, 40, 2, "Dot3InPauseFrames" },
+ { 0, 42, 2, "Dot3ControlInUnknownOpcodes" },
+ { 0, 44, 4, "IfOutOctets" },
+ { 0, 48, 2, "Dot3StatsSingleCollisionFrames" },
+ { 0, 50, 2, "Dot3StatMultipleCollisionFrames" },
+ { 0, 52, 2, "Dot3sDeferredTransmissions" },
+ { 0, 54, 2, "Dot3StatsLateCollisions" },
+ { 0, 56, 2, "EtherStatsCollisions" },
+ { 0, 58, 2, "Dot3StatsExcessiveCollisions" },
+ { 0, 60, 2, "Dot3OutPauseFrames" },
+ { 0, 62, 2, "Dot1dBasePortDelayExceededDiscards" },
+ { 0, 64, 2, "Dot1dTpPortInDiscards" },
+ { 0, 66, 2, "IfOutUcastPkts" },
+ { 0, 68, 2, "IfOutMulticastPkts" },
+ { 0, 70, 2, "IfOutBroadcastPkts" },
+};
+
+static int rtl8366rb_get_mib_counter(struct realtek_smi *smi,
+ int port,
+ struct rtl8366_mib_counter *mib,
+ u64 *mibvalue)
+{
+ u32 addr, val;
+ int ret;
+ int i;
+
+ addr = RTL8366RB_MIB_COUNTER_BASE +
+ RTL8366RB_MIB_COUNTER_PORT_OFFSET * (port) +
+ mib->offset;
+
+ /* Writing access counter address first
+ * then ASIC will prepare 64bits counter wait for being retrived
+ */
+ ret = regmap_write(smi->map, addr, 0); /* Write whatever */
+ if (ret)
+ return ret;
+
+ /* Read MIB control register */
+ ret = regmap_read(smi->map, RTL8366RB_MIB_CTRL_REG, &val);
+ if (ret)
+ return -EIO;
+
+ if (val & RTL8366RB_MIB_CTRL_BUSY_MASK)
+ return -EBUSY;
+
+ if (val & RTL8366RB_MIB_CTRL_RESET_MASK)
+ return -EIO;
+
+ /* Read each individual MIB 16 bits at the time */
+ *mibvalue = 0;
+ for (i = mib->length; i > 0; i--) {
+ ret = regmap_read(smi->map, addr + (i - 1), &val);
+ if (ret)
+ return ret;
+ *mibvalue = (*mibvalue << 16) | (val & 0xFFFF);
+ }
+ return 0;
+}
+
+static u32 rtl8366rb_get_irqmask(struct irq_data *d)
+{
+ int line = irqd_to_hwirq(d);
+ u32 val;
+
+ /* For line interrupts we combine link down in bits
+ * 6..11 with link up in bits 0..5 into one interrupt.
+ */
+ if (line < 12)
+ val = BIT(line) | BIT(line + 6);
+ else
+ val = BIT(line);
+ return val;
+}
+
+static void rtl8366rb_mask_irq(struct irq_data *d)
+{
+ struct realtek_smi *smi = irq_data_get_irq_chip_data(d);
+ int ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_MASK_REG,
+ rtl8366rb_get_irqmask(d), 0);
+ if (ret)
+ dev_err(smi->dev, "could not mask IRQ\n");
+}
+
+static void rtl8366rb_unmask_irq(struct irq_data *d)
+{
+ struct realtek_smi *smi = irq_data_get_irq_chip_data(d);
+ int ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_MASK_REG,
+ rtl8366rb_get_irqmask(d),
+ rtl8366rb_get_irqmask(d));
+ if (ret)
+ dev_err(smi->dev, "could not unmask IRQ\n");
+}
+
+static irqreturn_t rtl8366rb_irq(int irq, void *data)
+{
+ struct realtek_smi *smi = data;
+ u32 stat;
+ int ret;
+
+ /* This clears the IRQ status register */
+ ret = regmap_read(smi->map, RTL8366RB_INTERRUPT_STATUS_REG,
+ &stat);
+ if (ret) {
+ dev_err(smi->dev, "can't read interrupt status\n");
+ return IRQ_NONE;
+ }
+ stat &= RTL8366RB_INTERRUPT_VALID;
+ if (!stat)
+ return IRQ_NONE;
+ while (stat) {
+ int line = __ffs(stat);
+ int child_irq;
+
+ stat &= ~BIT(line);
+ /* For line interrupts we combine link down in bits
+ * 6..11 with link up in bits 0..5 into one interrupt.
+ */
+ if (line < 12 && line > 5)
+ line -= 5;
+ child_irq = irq_find_mapping(smi->irqdomain, line);
+ handle_nested_irq(child_irq);
+ }
+ return IRQ_HANDLED;
+}
+
+static struct irq_chip rtl8366rb_irq_chip = {
+ .name = "RTL8366RB",
+ .irq_mask = rtl8366rb_mask_irq,
+ .irq_unmask = rtl8366rb_unmask_irq,
+};
+
+static int rtl8366rb_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &rtl8366rb_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static void rtl8366rb_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_nested_thread(irq, 0);
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops rtl8366rb_irqdomain_ops = {
+ .map = rtl8366rb_irq_map,
+ .unmap = rtl8366rb_irq_unmap,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int rtl8366rb_setup_cascaded_irq(struct realtek_smi *smi)
+{
+ struct device_node *intc;
+ unsigned long irq_trig;
+ int irq;
+ int ret;
+ u32 val;
+ int i;
+
+ intc = of_get_child_by_name(smi->dev->of_node, "interrupt-controller");
+ if (!intc) {
+ dev_err(smi->dev, "missing child interrupt-controller node\n");
+ return -EINVAL;
+ }
+ /* RB8366RB IRQs cascade off this one */
+ irq = of_irq_get(intc, 0);
+ if (irq <= 0) {
+ dev_err(smi->dev, "failed to get parent IRQ\n");
+ return irq ? irq : -EINVAL;
+ }
+
+ /* This clears the IRQ status register */
+ ret = regmap_read(smi->map, RTL8366RB_INTERRUPT_STATUS_REG,
+ &val);
+ if (ret) {
+ dev_err(smi->dev, "can't read interrupt status\n");
+ return ret;
+ }
+
+ /* Fetch IRQ edge information from the descriptor */
+ irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+ switch (irq_trig) {
+ case IRQF_TRIGGER_RISING:
+ case IRQF_TRIGGER_HIGH:
+ dev_info(smi->dev, "active high/rising IRQ\n");
+ val = 0;
+ break;
+ case IRQF_TRIGGER_FALLING:
+ case IRQF_TRIGGER_LOW:
+ dev_info(smi->dev, "active low/falling IRQ\n");
+ val = RTL8366RB_INTERRUPT_POLARITY;
+ break;
+ }
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_INTERRUPT_POLARITY,
+ val);
+ if (ret) {
+ dev_err(smi->dev, "could not configure IRQ polarity\n");
+ return ret;
+ }
+
+ ret = devm_request_threaded_irq(smi->dev, irq, NULL,
+ rtl8366rb_irq, IRQF_ONESHOT,
+ "RTL8366RB", smi);
+ if (ret) {
+ dev_err(smi->dev, "unable to request irq: %d\n", ret);
+ return ret;
+ }
+ smi->irqdomain = irq_domain_add_linear(intc,
+ RTL8366RB_NUM_INTERRUPT,
+ &rtl8366rb_irqdomain_ops,
+ smi);
+ if (!smi->irqdomain) {
+ dev_err(smi->dev, "failed to create IRQ domain\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < smi->num_ports; i++)
+ irq_set_parent(irq_create_mapping(smi->irqdomain, i), irq);
+
+ return 0;
+}
+
+static int rtl8366rb_set_addr(struct realtek_smi *smi)
+{
+ u8 addr[ETH_ALEN];
+ u16 val;
+ int ret;
+
+ eth_random_addr(addr);
+
+ dev_info(smi->dev, "set MAC: %02X:%02X:%02X:%02X:%02X:%02X\n",
+ addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]);
+ val = addr[0] << 8 | addr[1];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR0, val);
+ if (ret)
+ return ret;
+ val = addr[2] << 8 | addr[3];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR1, val);
+ if (ret)
+ return ret;
+ val = addr[4] << 8 | addr[5];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR2, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+/* Found in a vendor driver */
+
+/* For the "version 0" early silicon, appear in most source releases */
+static const u16 rtl8366rb_init_jam_ver_0[] = {
+ 0x000B, 0x0001, 0x03A6, 0x0100, 0x03A7, 0x0001, 0x02D1, 0x3FFF,
+ 0x02D2, 0x3FFF, 0x02D3, 0x3FFF, 0x02D4, 0x3FFF, 0x02D5, 0x3FFF,
+ 0x02D6, 0x3FFF, 0x02D7, 0x3FFF, 0x02D8, 0x3FFF, 0x022B, 0x0688,
+ 0x022C, 0x0FAC, 0x03D0, 0x4688, 0x03D1, 0x01F5, 0x0000, 0x0830,
+ 0x02F9, 0x0200, 0x02F7, 0x7FFF, 0x02F8, 0x03FF, 0x0080, 0x03E8,
+ 0x0081, 0x00CE, 0x0082, 0x00DA, 0x0083, 0x0230, 0xBE0F, 0x2000,
+ 0x0231, 0x422A, 0x0232, 0x422A, 0x0233, 0x422A, 0x0234, 0x422A,
+ 0x0235, 0x422A, 0x0236, 0x422A, 0x0237, 0x422A, 0x0238, 0x422A,
+ 0x0239, 0x422A, 0x023A, 0x422A, 0x023B, 0x422A, 0x023C, 0x422A,
+ 0x023D, 0x422A, 0x023E, 0x422A, 0x023F, 0x422A, 0x0240, 0x422A,
+ 0x0241, 0x422A, 0x0242, 0x422A, 0x0243, 0x422A, 0x0244, 0x422A,
+ 0x0245, 0x422A, 0x0246, 0x422A, 0x0247, 0x422A, 0x0248, 0x422A,
+ 0x0249, 0x0146, 0x024A, 0x0146, 0x024B, 0x0146, 0xBE03, 0xC961,
+ 0x024D, 0x0146, 0x024E, 0x0146, 0x024F, 0x0146, 0x0250, 0x0146,
+ 0xBE64, 0x0226, 0x0252, 0x0146, 0x0253, 0x0146, 0x024C, 0x0146,
+ 0x0251, 0x0146, 0x0254, 0x0146, 0xBE62, 0x3FD0, 0x0084, 0x0320,
+ 0x0255, 0x0146, 0x0256, 0x0146, 0x0257, 0x0146, 0x0258, 0x0146,
+ 0x0259, 0x0146, 0x025A, 0x0146, 0x025B, 0x0146, 0x025C, 0x0146,
+ 0x025D, 0x0146, 0x025E, 0x0146, 0x025F, 0x0146, 0x0260, 0x0146,
+ 0x0261, 0xA23F, 0x0262, 0x0294, 0x0263, 0xA23F, 0x0264, 0x0294,
+ 0x0265, 0xA23F, 0x0266, 0x0294, 0x0267, 0xA23F, 0x0268, 0x0294,
+ 0x0269, 0xA23F, 0x026A, 0x0294, 0x026B, 0xA23F, 0x026C, 0x0294,
+ 0x026D, 0xA23F, 0x026E, 0x0294, 0x026F, 0xA23F, 0x0270, 0x0294,
+ 0x02F5, 0x0048, 0xBE09, 0x0E00, 0xBE1E, 0x0FA0, 0xBE14, 0x8448,
+ 0xBE15, 0x1007, 0xBE4A, 0xA284, 0xC454, 0x3F0B, 0xC474, 0x3F0B,
+ 0xBE48, 0x3672, 0xBE4B, 0x17A7, 0xBE4C, 0x0B15, 0xBE52, 0x0EDD,
+ 0xBE49, 0x8C00, 0xBE5B, 0x785C, 0xBE5C, 0x785C, 0xBE5D, 0x785C,
+ 0xBE61, 0x368A, 0xBE63, 0x9B84, 0xC456, 0xCC13, 0xC476, 0xCC13,
+ 0xBE65, 0x307D, 0xBE6D, 0x0005, 0xBE6E, 0xE120, 0xBE2E, 0x7BAF,
+};
+
+/* This v1 init sequence is from Belkin F5D8235 U-Boot release */
+static const u16 rtl8366rb_init_jam_ver_1[] = {
+ 0x0000, 0x0830, 0x0001, 0x8000, 0x0400, 0x8130, 0xBE78, 0x3C3C,
+ 0x0431, 0x5432, 0xBE37, 0x0CE4, 0x02FA, 0xFFDF, 0x02FB, 0xFFE0,
+ 0xC44C, 0x1585, 0xC44C, 0x1185, 0xC44C, 0x1585, 0xC46C, 0x1585,
+ 0xC46C, 0x1185, 0xC46C, 0x1585, 0xC451, 0x2135, 0xC471, 0x2135,
+ 0xBE10, 0x8140, 0xBE15, 0x0007, 0xBE6E, 0xE120, 0xBE69, 0xD20F,
+ 0xBE6B, 0x0320, 0xBE24, 0xB000, 0xBE23, 0xFF51, 0xBE22, 0xDF20,
+ 0xBE21, 0x0140, 0xBE20, 0x00BB, 0xBE24, 0xB800, 0xBE24, 0x0000,
+ 0xBE24, 0x7000, 0xBE23, 0xFF51, 0xBE22, 0xDF60, 0xBE21, 0x0140,
+ 0xBE20, 0x0077, 0xBE24, 0x7800, 0xBE24, 0x0000, 0xBE2E, 0x7B7A,
+ 0xBE36, 0x0CE4, 0x02F5, 0x0048, 0xBE77, 0x2940, 0x000A, 0x83E0,
+ 0xBE79, 0x3C3C, 0xBE00, 0x1340,
+};
+
+/* This v2 init sequence is from Belkin F5D8235 U-Boot release */
+static const u16 rtl8366rb_init_jam_ver_2[] = {
+ 0x0450, 0x0000, 0x0400, 0x8130, 0x000A, 0x83ED, 0x0431, 0x5432,
+ 0xC44F, 0x6250, 0xC46F, 0x6250, 0xC456, 0x0C14, 0xC476, 0x0C14,
+ 0xC44C, 0x1C85, 0xC44C, 0x1885, 0xC44C, 0x1C85, 0xC46C, 0x1C85,
+ 0xC46C, 0x1885, 0xC46C, 0x1C85, 0xC44C, 0x0885, 0xC44C, 0x0881,
+ 0xC44C, 0x0885, 0xC46C, 0x0885, 0xC46C, 0x0881, 0xC46C, 0x0885,
+ 0xBE2E, 0x7BA7, 0xBE36, 0x1000, 0xBE37, 0x1000, 0x8000, 0x0001,
+ 0xBE69, 0xD50F, 0x8000, 0x0000, 0xBE69, 0xD50F, 0xBE6E, 0x0320,
+ 0xBE77, 0x2940, 0xBE78, 0x3C3C, 0xBE79, 0x3C3C, 0xBE6E, 0xE120,
+ 0x8000, 0x0001, 0xBE15, 0x1007, 0x8000, 0x0000, 0xBE15, 0x1007,
+ 0xBE14, 0x0448, 0xBE1E, 0x00A0, 0xBE10, 0x8160, 0xBE10, 0x8140,
+ 0xBE00, 0x1340, 0x0F51, 0x0010,
+};
+
+/* Appears in a DDWRT code dump */
+static const u16 rtl8366rb_init_jam_ver_3[] = {
+ 0x0000, 0x0830, 0x0400, 0x8130, 0x000A, 0x83ED, 0x0431, 0x5432,
+ 0x0F51, 0x0017, 0x02F5, 0x0048, 0x02FA, 0xFFDF, 0x02FB, 0xFFE0,
+ 0xC456, 0x0C14, 0xC476, 0x0C14, 0xC454, 0x3F8B, 0xC474, 0x3F8B,
+ 0xC450, 0x2071, 0xC470, 0x2071, 0xC451, 0x226B, 0xC471, 0x226B,
+ 0xC452, 0xA293, 0xC472, 0xA293, 0xC44C, 0x1585, 0xC44C, 0x1185,
+ 0xC44C, 0x1585, 0xC46C, 0x1585, 0xC46C, 0x1185, 0xC46C, 0x1585,
+ 0xC44C, 0x0185, 0xC44C, 0x0181, 0xC44C, 0x0185, 0xC46C, 0x0185,
+ 0xC46C, 0x0181, 0xC46C, 0x0185, 0xBE24, 0xB000, 0xBE23, 0xFF51,
+ 0xBE22, 0xDF20, 0xBE21, 0x0140, 0xBE20, 0x00BB, 0xBE24, 0xB800,
+ 0xBE24, 0x0000, 0xBE24, 0x7000, 0xBE23, 0xFF51, 0xBE22, 0xDF60,
+ 0xBE21, 0x0140, 0xBE20, 0x0077, 0xBE24, 0x7800, 0xBE24, 0x0000,
+ 0xBE2E, 0x7BA7, 0xBE36, 0x1000, 0xBE37, 0x1000, 0x8000, 0x0001,
+ 0xBE69, 0xD50F, 0x8000, 0x0000, 0xBE69, 0xD50F, 0xBE6B, 0x0320,
+ 0xBE77, 0x2800, 0xBE78, 0x3C3C, 0xBE79, 0x3C3C, 0xBE6E, 0xE120,
+ 0x8000, 0x0001, 0xBE10, 0x8140, 0x8000, 0x0000, 0xBE10, 0x8140,
+ 0xBE15, 0x1007, 0xBE14, 0x0448, 0xBE1E, 0x00A0, 0xBE10, 0x8160,
+ 0xBE10, 0x8140, 0xBE00, 0x1340, 0x0450, 0x0000, 0x0401, 0x0000,
+};
+
+/* Belkin F5D8235 v1, "belkin,f5d8235-v1" */
+static const u16 rtl8366rb_init_jam_f5d8235[] = {
+ 0x0242, 0x02BF, 0x0245, 0x02BF, 0x0248, 0x02BF, 0x024B, 0x02BF,
+ 0x024E, 0x02BF, 0x0251, 0x02BF, 0x0254, 0x0A3F, 0x0256, 0x0A3F,
+ 0x0258, 0x0A3F, 0x025A, 0x0A3F, 0x025C, 0x0A3F, 0x025E, 0x0A3F,
+ 0x0263, 0x007C, 0x0100, 0x0004, 0xBE5B, 0x3500, 0x800E, 0x200F,
+ 0xBE1D, 0x0F00, 0x8001, 0x5011, 0x800A, 0xA2F4, 0x800B, 0x17A3,
+ 0xBE4B, 0x17A3, 0xBE41, 0x5011, 0xBE17, 0x2100, 0x8000, 0x8304,
+ 0xBE40, 0x8304, 0xBE4A, 0xA2F4, 0x800C, 0xA8D5, 0x8014, 0x5500,
+ 0x8015, 0x0004, 0xBE4C, 0xA8D5, 0xBE59, 0x0008, 0xBE09, 0x0E00,
+ 0xBE36, 0x1036, 0xBE37, 0x1036, 0x800D, 0x00FF, 0xBE4D, 0x00FF,
+};
+
+/* DGN3500, "netgear,dgn3500", "netgear,dgn3500b" */
+static const u16 rtl8366rb_init_jam_dgn3500[] = {
+ 0x0000, 0x0830, 0x0400, 0x8130, 0x000A, 0x83ED, 0x0F51, 0x0017,
+ 0x02F5, 0x0048, 0x02FA, 0xFFDF, 0x02FB, 0xFFE0, 0x0450, 0x0000,
+ 0x0401, 0x0000, 0x0431, 0x0960,
+};
+
+/* This jam table activates "green ethernet", which means low power mode
+ * and is claimed to detect the cable length and not use more power than
+ * necessary, and the ports should enter power saving mode 10 seconds after
+ * a cable is disconnected. Seems to always be the same.
+ */
+static const u16 rtl8366rb_green_jam[][2] = {
+ {0xBE78, 0x323C}, {0xBE77, 0x5000}, {0xBE2E, 0x7BA7},
+ {0xBE59, 0x3459}, {0xBE5A, 0x745A}, {0xBE5B, 0x785C},
+ {0xBE5C, 0x785C}, {0xBE6E, 0xE120}, {0xBE79, 0x323C},
+};
+
+static int rtl8366rb_setup(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+ const u16 *jam_table;
+ u32 chip_ver = 0;
+ u32 chip_id = 0;
+ int jam_size;
+ u32 val;
+ int ret;
+ int i;
+
+ ret = regmap_read(smi->map, RTL8366RB_CHIP_ID_REG, &chip_id);
+ if (ret) {
+ dev_err(smi->dev, "unable to read chip id\n");
+ return ret;
+ }
+
+ switch (chip_id) {
+ case RTL8366RB_CHIP_ID_8366:
+ break;
+ default:
+ dev_err(smi->dev, "unknown chip id (%04x)\n", chip_id);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(smi->map, RTL8366RB_CHIP_VERSION_CTRL_REG,
+ &chip_ver);
+ if (ret) {
+ dev_err(smi->dev, "unable to read chip version\n");
+ return ret;
+ }
+
+ dev_info(smi->dev, "RTL%04x ver %u chip found\n",
+ chip_id, chip_ver & RTL8366RB_CHIP_VERSION_MASK);
+
+ /* Do the init dance using the right jam table */
+ switch (chip_ver) {
+ case 0:
+ jam_table = rtl8366rb_init_jam_ver_0;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_0);
+ break;
+ case 1:
+ jam_table = rtl8366rb_init_jam_ver_1;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_1);
+ break;
+ case 2:
+ jam_table = rtl8366rb_init_jam_ver_2;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_2);
+ break;
+ default:
+ jam_table = rtl8366rb_init_jam_ver_3;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_3);
+ break;
+ }
+
+ /* Special jam tables for special routers
+ * TODO: are these necessary? Maintainers, please test
+ * without them, using just the off-the-shelf tables.
+ */
+ if (of_machine_is_compatible("belkin,f5d8235-v1")) {
+ jam_table = rtl8366rb_init_jam_f5d8235;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_f5d8235);
+ }
+ if (of_machine_is_compatible("netgear,dgn3500") ||
+ of_machine_is_compatible("netgear,dgn3500b")) {
+ jam_table = rtl8366rb_init_jam_dgn3500;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_dgn3500);
+ }
+
+ i = 0;
+ while (i < jam_size) {
+ if ((jam_table[i] & 0xBE00) == 0xBE00) {
+ ret = regmap_read(smi->map,
+ RTL8366RB_PHY_ACCESS_BUSY_REG,
+ &val);
+ if (ret)
+ return ret;
+ if (!(val & RTL8366RB_PHY_INT_BUSY)) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+ }
+ }
+ dev_dbg(smi->dev, "jam %04x into register %04x\n",
+ jam_table[i + 1],
+ jam_table[i]);
+ ret = regmap_write(smi->map,
+ jam_table[i],
+ jam_table[i + 1]);
+ if (ret)
+ return ret;
+ i += 2;
+ }
+
+ /* Set up the "green ethernet" feature */
+ i = 0;
+ while (i < ARRAY_SIZE(rtl8366rb_green_jam)) {
+ ret = regmap_read(smi->map, RTL8366RB_PHY_ACCESS_BUSY_REG,
+ &val);
+ if (ret)
+ return ret;
+ if (!(val & RTL8366RB_PHY_INT_BUSY)) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+ ret = regmap_write(smi->map,
+ rtl8366rb_green_jam[i][0],
+ rtl8366rb_green_jam[i][1]);
+ if (ret)
+ return ret;
+ i++;
+ }
+ }
+ ret = regmap_write(smi->map,
+ RTL8366RB_GREEN_FEATURE_REG,
+ (chip_ver == 1) ? 0x0007 : 0x0003);
+ if (ret)
+ return ret;
+
+ /* Vendor driver sets 0x240 in registers 0xc and 0xd (undocumented) */
+ ret = regmap_write(smi->map, 0x0c, 0x240);
+ if (ret)
+ return ret;
+ ret = regmap_write(smi->map, 0x0d, 0x240);
+ if (ret)
+ return ret;
+
+ /* Set some random MAC address */
+ ret = rtl8366rb_set_addr(smi);
+ if (ret)
+ return ret;
+
+ /* Enable CPU port and enable inserting CPU tag
+ *
+ * Disabling RTL8368RB_CPU_INSTAG here will change the behaviour
+ * of the switch totally and it will start talking Realtek RRCP
+ * internally. It is probably possible to experiment with this,
+ * but then the kernel needs to understand and handle RRCP first.
+ */
+ ret = regmap_update_bits(smi->map, RTL8368RB_CPU_CTRL_REG,
+ 0xFFFF,
+ RTL8368RB_CPU_INSTAG | BIT(smi->cpu_port));
+ if (ret)
+ return ret;
+
+ /* Make sure we default-enable the fixed CPU port */
+ ret = regmap_update_bits(smi->map, RTL8366RB_PECR,
+ BIT(smi->cpu_port),
+ 0);
+ if (ret)
+ return ret;
+
+ /* Set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(smi->map, RTL8366RB_SGCR,
+ RTL8366RB_SGCR_MAX_LENGTH_MASK,
+ RTL8366RB_SGCR_MAX_LENGTH_1536);
+ if (ret)
+ return ret;
+
+ /* Enable learning for all ports */
+ ret = regmap_write(smi->map, RTL8366RB_SSCR0, 0);
+ if (ret)
+ return ret;
+
+ /* Enable auto ageing for all ports */
+ ret = regmap_write(smi->map, RTL8366RB_SSCR1, 0);
+ if (ret)
+ return ret;
+
+ /* Discard VLAN tagged packets if the port is not a member of
+ * the VLAN with which the packets is associated.
+ */
+ ret = regmap_write(smi->map, RTL8366RB_VLAN_INGRESS_CTRL2_REG,
+ RTL8366RB_PORT_ALL);
+ if (ret)
+ return ret;
+
+ /* Don't drop packets whose DA has not been learned */
+ ret = regmap_update_bits(smi->map, RTL8366RB_SSCR2,
+ RTL8366RB_SSCR2_DROP_UNKNOWN_DA, 0);
+ if (ret)
+ return ret;
+
+ /* Set blinking, TODO: make this configurable */
+ ret = regmap_update_bits(smi->map, RTL8366RB_LED_BLINKRATE_REG,
+ RTL8366RB_LED_BLINKRATE_MASK,
+ RTL8366RB_LED_BLINKRATE_56MS);
+ if (ret)
+ return ret;
+
+ /* Set up LED activity:
+ * Each port has 4 LEDs, we configure all ports to the same
+ * behaviour (no individual config) but we can set up each
+ * LED separately.
+ */
+ if (smi->leds_disabled) {
+ /* Turn everything off */
+ regmap_update_bits(smi->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x0FFF, 0);
+ regmap_update_bits(smi->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x0FFF, 0);
+ regmap_update_bits(smi->map,
+ RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_P4_RGMII_LED,
+ 0);
+ val = RTL8366RB_LED_OFF;
+ } else {
+ /* TODO: make this configurable per LED */
+ val = RTL8366RB_LED_FORCE;
+ }
+ for (i = 0; i < 4; i++) {
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_LED_CTRL_REG,
+ 0xf << (i * 4),
+ val << (i * 4));
+ if (ret)
+ return ret;
+ }
+
+ ret = rtl8366_init_vlan(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8366rb_setup_cascaded_irq(smi);
+ if (ret)
+ dev_info(smi->dev, "no interrupt support\n");
+
+ ret = realtek_smi_setup_mdio(smi);
+ if (ret) {
+ dev_info(smi->dev, "could not set up MDIO bus\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static enum dsa_tag_protocol rtl8366_get_tag_protocol(struct dsa_switch *ds,
+ int port)
+{
+ /* For now, the RTL switches are handled without any custom tags.
+ *
+ * It is possible to turn on "custom tags" by removing the
+ * RTL8368RB_CPU_INSTAG flag when enabling the port but what it
+ * does is unfamiliar to DSA: ethernet frames of type 8899, the Realtek
+ * Remote Control Protocol (RRCP) start to appear on the CPU port of
+ * the device. So this is not the ordinary few extra bytes in the
+ * frame. Instead it appears that the switch starts to talk Realtek
+ * RRCP internally which means a pretty complex RRCP implementation
+ * decoding and responding the RRCP protocol is needed to exploit this.
+ *
+ * The OpenRRCP project (dormant since 2009) have reverse-egineered
+ * parts of the protocol.
+ */
+ return DSA_TAG_PROTO_NONE;
+}
+
+static void rtl8366rb_adjust_link(struct dsa_switch *ds, int port,
+ struct phy_device *phydev)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (port != smi->cpu_port)
+ return;
+
+ dev_info(smi->dev, "adjust link on CPU port (%d)\n", port);
+
+ /* Force the fixed CPU port into 1Gbit mode, no autonegotiation */
+ ret = regmap_update_bits(smi->map, RTL8366RB_MAC_FORCE_CTRL_REG,
+ BIT(port), BIT(port));
+ if (ret)
+ return;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_PAACR2,
+ 0xFF00U,
+ RTL8366RB_PAACR_CPU_PORT << 8);
+ if (ret)
+ return;
+
+ /* Enable the CPU port */
+ ret = regmap_update_bits(smi->map, RTL8366RB_PECR, BIT(port),
+ 0);
+ if (ret)
+ return;
+}
+
+static void rb8366rb_set_port_led(struct realtek_smi *smi,
+ int port, bool enable)
+{
+ u16 val = enable ? 0x3f : 0;
+ int ret;
+
+ if (smi->leds_disabled)
+ return;
+
+ switch (port) {
+ case 0:
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x3F, val);
+ break;
+ case 1:
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x3F << RTL8366RB_LED_1_OFFSET,
+ val << RTL8366RB_LED_1_OFFSET);
+ break;
+ case 2:
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x3F, val);
+ break;
+ case 3:
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x3F << RTL8366RB_LED_3_OFFSET,
+ val << RTL8366RB_LED_3_OFFSET);
+ break;
+ case 4:
+ ret = regmap_update_bits(smi->map,
+ RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_P4_RGMII_LED,
+ enable ? RTL8366RB_P4_RGMII_LED : 0);
+ break;
+ default:
+ dev_err(smi->dev, "no LED for port %d\n", port);
+ return;
+ }
+ if (ret)
+ dev_err(smi->dev, "error updating LED on port %d\n", port);
+}
+
+static int
+rtl8366rb_port_enable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ dev_dbg(smi->dev, "enable port %d\n", port);
+ ret = regmap_update_bits(smi->map, RTL8366RB_PECR, BIT(port),
+ 0);
+ if (ret)
+ return ret;
+
+ rb8366rb_set_port_led(smi, port, true);
+ return 0;
+}
+
+static void
+rtl8366rb_port_disable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ dev_dbg(smi->dev, "disable port %d\n", port);
+ ret = regmap_update_bits(smi->map, RTL8366RB_PECR, BIT(port),
+ BIT(port));
+ if (ret)
+ return;
+
+ rb8366rb_set_port_led(smi, port, false);
+}
+
+static int rtl8366rb_get_vlan_4k(struct realtek_smi *smi, u32 vid,
+ struct rtl8366_vlan_4k *vlan4k)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ memset(vlan4k, '\0', sizeof(struct rtl8366_vlan_4k));
+
+ if (vid >= RTL8366RB_NUM_VIDS)
+ return -EINVAL;
+
+ /* write VID */
+ ret = regmap_write(smi->map, RTL8366RB_VLAN_TABLE_WRITE_BASE,
+ vid & RTL8366RB_VLAN_VID_MASK);
+ if (ret)
+ return ret;
+
+ /* write table access control word */
+ ret = regmap_write(smi->map, RTL8366RB_TABLE_ACCESS_CTRL_REG,
+ RTL8366RB_TABLE_VLAN_READ_CTRL);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_read(smi->map,
+ RTL8366RB_VLAN_TABLE_READ_BASE + i,
+ &data[i]);
+ if (ret)
+ return ret;
+ }
+
+ vlan4k->vid = vid;
+ vlan4k->untag = (data[1] >> RTL8366RB_VLAN_UNTAG_SHIFT) &
+ RTL8366RB_VLAN_UNTAG_MASK;
+ vlan4k->member = data[1] & RTL8366RB_VLAN_MEMBER_MASK;
+ vlan4k->fid = data[2] & RTL8366RB_VLAN_FID_MASK;
+
+ return 0;
+}
+
+static int rtl8366rb_set_vlan_4k(struct realtek_smi *smi,
+ const struct rtl8366_vlan_4k *vlan4k)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ if (vlan4k->vid >= RTL8366RB_NUM_VIDS ||
+ vlan4k->member > RTL8366RB_VLAN_MEMBER_MASK ||
+ vlan4k->untag > RTL8366RB_VLAN_UNTAG_MASK ||
+ vlan4k->fid > RTL8366RB_FIDMAX)
+ return -EINVAL;
+
+ data[0] = vlan4k->vid & RTL8366RB_VLAN_VID_MASK;
+ data[1] = (vlan4k->member & RTL8366RB_VLAN_MEMBER_MASK) |
+ ((vlan4k->untag & RTL8366RB_VLAN_UNTAG_MASK) <<
+ RTL8366RB_VLAN_UNTAG_SHIFT);
+ data[2] = vlan4k->fid & RTL8366RB_VLAN_FID_MASK;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_VLAN_TABLE_WRITE_BASE + i,
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ /* write table access control word */
+ ret = regmap_write(smi->map, RTL8366RB_TABLE_ACCESS_CTRL_REG,
+ RTL8366RB_TABLE_VLAN_WRITE_CTRL);
+
+ return ret;
+}
+
+static int rtl8366rb_get_vlan_mc(struct realtek_smi *smi, u32 index,
+ struct rtl8366_vlan_mc *vlanmc)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ memset(vlanmc, '\0', sizeof(struct rtl8366_vlan_mc));
+
+ if (index >= RTL8366RB_NUM_VLANS)
+ return -EINVAL;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_read(smi->map,
+ RTL8366RB_VLAN_MC_BASE(index) + i,
+ &data[i]);
+ if (ret)
+ return ret;
+ }
+
+ vlanmc->vid = data[0] & RTL8366RB_VLAN_VID_MASK;
+ vlanmc->priority = (data[0] >> RTL8366RB_VLAN_PRIORITY_SHIFT) &
+ RTL8366RB_VLAN_PRIORITY_MASK;
+ vlanmc->untag = (data[1] >> RTL8366RB_VLAN_UNTAG_SHIFT) &
+ RTL8366RB_VLAN_UNTAG_MASK;
+ vlanmc->member = data[1] & RTL8366RB_VLAN_MEMBER_MASK;
+ vlanmc->fid = data[2] & RTL8366RB_VLAN_FID_MASK;
+
+ return 0;
+}
+
+static int rtl8366rb_set_vlan_mc(struct realtek_smi *smi, u32 index,
+ const struct rtl8366_vlan_mc *vlanmc)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ if (index >= RTL8366RB_NUM_VLANS ||
+ vlanmc->vid >= RTL8366RB_NUM_VIDS ||
+ vlanmc->priority > RTL8366RB_PRIORITYMAX ||
+ vlanmc->member > RTL8366RB_VLAN_MEMBER_MASK ||
+ vlanmc->untag > RTL8366RB_VLAN_UNTAG_MASK ||
+ vlanmc->fid > RTL8366RB_FIDMAX)
+ return -EINVAL;
+
+ data[0] = (vlanmc->vid & RTL8366RB_VLAN_VID_MASK) |
+ ((vlanmc->priority & RTL8366RB_VLAN_PRIORITY_MASK) <<
+ RTL8366RB_VLAN_PRIORITY_SHIFT);
+ data[1] = (vlanmc->member & RTL8366RB_VLAN_MEMBER_MASK) |
+ ((vlanmc->untag & RTL8366RB_VLAN_UNTAG_MASK) <<
+ RTL8366RB_VLAN_UNTAG_SHIFT);
+ data[2] = vlanmc->fid & RTL8366RB_VLAN_FID_MASK;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_VLAN_MC_BASE(index) + i,
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8366rb_get_mc_index(struct realtek_smi *smi, int port, int *val)
+{
+ u32 data;
+ int ret;
+
+ if (port >= smi->num_ports)
+ return -EINVAL;
+
+ ret = regmap_read(smi->map, RTL8366RB_PORT_VLAN_CTRL_REG(port),
+ &data);
+ if (ret)
+ return ret;
+
+ *val = (data >> RTL8366RB_PORT_VLAN_CTRL_SHIFT(port)) &
+ RTL8366RB_PORT_VLAN_CTRL_MASK;
+
+ return 0;
+}
+
+static int rtl8366rb_set_mc_index(struct realtek_smi *smi, int port, int index)
+{
+ if (port >= smi->num_ports || index >= RTL8366RB_NUM_VLANS)
+ return -EINVAL;
+
+ return regmap_update_bits(smi->map, RTL8366RB_PORT_VLAN_CTRL_REG(port),
+ RTL8366RB_PORT_VLAN_CTRL_MASK <<
+ RTL8366RB_PORT_VLAN_CTRL_SHIFT(port),
+ (index & RTL8366RB_PORT_VLAN_CTRL_MASK) <<
+ RTL8366RB_PORT_VLAN_CTRL_SHIFT(port));
+}
+
+static bool rtl8366rb_is_vlan_valid(struct realtek_smi *smi, unsigned int vlan)
+{
+ unsigned int max = RTL8366RB_NUM_VLANS;
+
+ if (smi->vlan4k_enabled)
+ max = RTL8366RB_NUM_VIDS - 1;
+
+ if (vlan == 0 || vlan >= max)
+ return false;
+
+ return true;
+}
+
+static int rtl8366rb_enable_vlan(struct realtek_smi *smi, bool enable)
+{
+ dev_dbg(smi->dev, "%s VLAN\n", enable ? "enable" : "disable");
+ return regmap_update_bits(smi->map,
+ RTL8366RB_SGCR, RTL8366RB_SGCR_EN_VLAN,
+ enable ? RTL8366RB_SGCR_EN_VLAN : 0);
+}
+
+static int rtl8366rb_enable_vlan4k(struct realtek_smi *smi, bool enable)
+{
+ dev_dbg(smi->dev, "%s VLAN 4k\n", enable ? "enable" : "disable");
+ return regmap_update_bits(smi->map, RTL8366RB_SGCR,
+ RTL8366RB_SGCR_EN_VLAN_4KTB,
+ enable ? RTL8366RB_SGCR_EN_VLAN_4KTB : 0);
+}
+
+static int rtl8366rb_phy_read(struct realtek_smi *smi, int phy, int regnum)
+{
+ u32 val;
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(smi->map, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_READ);
+ if (ret)
+ return ret;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ ret = regmap_write(smi->map, reg, 0);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to write PHY%d reg %04x @ %04x, ret %d\n",
+ phy, regnum, reg, ret);
+ return ret;
+ }
+
+ ret = regmap_read(smi->map, RTL8366RB_PHY_ACCESS_DATA_REG, &val);
+ if (ret)
+ return ret;
+
+ dev_dbg(smi->dev, "read PHY%d register 0x%04x @ %08x, val <- %04x\n",
+ phy, regnum, reg, val);
+
+ return val;
+}
+
+static int rtl8366rb_phy_write(struct realtek_smi *smi, int phy, int regnum,
+ u16 val)
+{
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(smi->map, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ dev_dbg(smi->dev, "write PHY%d register 0x%04x @ %04x, val -> %04x\n",
+ phy, regnum, reg, val);
+
+ ret = regmap_write(smi->map, reg, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8366rb_reset_chip(struct realtek_smi *smi)
+{
+ int timeout = 10;
+ u32 val;
+ int ret;
+
+ realtek_smi_write_reg_noack(smi, RTL8366RB_RESET_CTRL_REG,
+ RTL8366RB_CHIP_CTRL_RESET_HW);
+ do {
+ usleep_range(20000, 25000);
+ ret = regmap_read(smi->map, RTL8366RB_RESET_CTRL_REG, &val);
+ if (ret)
+ return ret;
+
+ if (!(val & RTL8366RB_CHIP_CTRL_RESET_HW))
+ break;
+ } while (--timeout);
+
+ if (!timeout) {
+ dev_err(smi->dev, "timeout waiting for the switch to reset\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int rtl8366rb_detect(struct realtek_smi *smi)
+{
+ struct device *dev = smi->dev;
+ int ret;
+ u32 val;
+
+ /* Detect device */
+ ret = regmap_read(smi->map, 0x5c, &val);
+ if (ret) {
+ dev_err(dev, "can't get chip ID (%d)\n", ret);
+ return ret;
+ }
+
+ switch (val) {
+ case 0x6027:
+ dev_info(dev, "found an RTL8366S switch\n");
+ dev_err(dev, "this switch is not yet supported, submit patches!\n");
+ return -ENODEV;
+ case 0x5937:
+ dev_info(dev, "found an RTL8366RB switch\n");
+ smi->cpu_port = RTL8366RB_PORT_NUM_CPU;
+ smi->num_ports = RTL8366RB_NUM_PORTS;
+ smi->num_vlan_mc = RTL8366RB_NUM_VLANS;
+ smi->mib_counters = rtl8366rb_mib_counters;
+ smi->num_mib_counters = ARRAY_SIZE(rtl8366rb_mib_counters);
+ break;
+ default:
+ dev_info(dev, "found an Unknown Realtek switch (id=0x%04x)\n",
+ val);
+ break;
+ }
+
+ ret = rtl8366rb_reset_chip(smi);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl8366rb_switch_ops = {
+ .get_tag_protocol = rtl8366_get_tag_protocol,
+ .setup = rtl8366rb_setup,
+ .adjust_link = rtl8366rb_adjust_link,
+ .get_strings = rtl8366_get_strings,
+ .get_ethtool_stats = rtl8366_get_ethtool_stats,
+ .get_sset_count = rtl8366_get_sset_count,
+ .port_vlan_filtering = rtl8366_vlan_filtering,
+ .port_vlan_prepare = rtl8366_vlan_prepare,
+ .port_vlan_add = rtl8366_vlan_add,
+ .port_vlan_del = rtl8366_vlan_del,
+ .port_enable = rtl8366rb_port_enable,
+ .port_disable = rtl8366rb_port_disable,
+};
+
+static const struct realtek_smi_ops rtl8366rb_smi_ops = {
+ .detect = rtl8366rb_detect,
+ .get_vlan_mc = rtl8366rb_get_vlan_mc,
+ .set_vlan_mc = rtl8366rb_set_vlan_mc,
+ .get_vlan_4k = rtl8366rb_get_vlan_4k,
+ .set_vlan_4k = rtl8366rb_set_vlan_4k,
+ .get_mc_index = rtl8366rb_get_mc_index,
+ .set_mc_index = rtl8366rb_set_mc_index,
+ .get_mib_counter = rtl8366rb_get_mib_counter,
+ .is_vlan_valid = rtl8366rb_is_vlan_valid,
+ .enable_vlan = rtl8366rb_enable_vlan,
+ .enable_vlan4k = rtl8366rb_enable_vlan4k,
+ .phy_read = rtl8366rb_phy_read,
+ .phy_write = rtl8366rb_phy_write,
+};
+
+const struct realtek_smi_variant rtl8366rb_variant = {
+ .ds_ops = &rtl8366rb_switch_ops,
+ .ops = &rtl8366rb_smi_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xa9,
+ .cmd_write = 0xa8,
+};
+EXPORT_SYMBOL_GPL(rtl8366rb_variant);
projects / nvme.git / commitdiff