wl18xx: enable MIMO rates when connected as a MIMO STA

Use this opportunity to consolidate the check for MIMO support into a
separate function.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index 2b9398c02a253d9df9ecd1d911fb7462250663cd..69042bb9a0975637be043e2d89d7fdc16b3a9b34 100644 (file)
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -1013,6 +1013,13 @@ static void wl18xx_set_rx_csum(struct wl1271 *wl,
                skb->ip_summed = CHECKSUM_UNNECESSARY;
 }
 
+static bool wl18xx_is_mimo_supported(struct wl1271 *wl)
+{
+       struct wl18xx_priv *priv = wl->priv;
+
+       return priv->conf.phy.number_of_assembled_ant2_4 >= 2;
+}
+
 /*
  * TODO: instead of having these two functions to get the rate mask,
  * we should modify the wlvif->rate_set instead
@@ -1029,6 +1036,9 @@ static u32 wl18xx_sta_get_ap_rate_mask(struct wl1271 *wl,
 
                /* we don't support MIMO in wide-channel mode */
                hw_rate_set &= ~CONF_TX_MIMO_RATES;
+       } else if (wl18xx_is_mimo_supported(wl)) {
+               wl1271_debug(DEBUG_ACX, "using MIMO channel rate mask");
+               hw_rate_set |= CONF_TX_MIMO_RATES;
        }
 
        return hw_rate_set;
@@ -1037,8 +1047,6 @@ static u32 wl18xx_sta_get_ap_rate_mask(struct wl1271 *wl,
 static u32 wl18xx_ap_get_mimo_wide_rate_mask(struct wl1271 *wl,
                                             struct wl12xx_vif *wlvif)
 {
-       struct wl18xx_priv *priv = wl->priv;
-
        if (wlvif->channel_type == NL80211_CHAN_HT40MINUS ||
            wlvif->channel_type == NL80211_CHAN_HT40PLUS) {
                wl1271_debug(DEBUG_ACX, "using wide channel rate mask");
@@ -1048,7 +1056,7 @@ static u32 wl18xx_ap_get_mimo_wide_rate_mask(struct wl1271 *wl,
                        return 0;
 
                return CONF_TX_RATE_USE_WIDE_CHAN;
-       } else if (priv->conf.phy.number_of_assembled_ant2_4 >= 2 &&
+       } else if (wl18xx_is_mimo_supported(wl) &&
                   wlvif->band == IEEE80211_BAND_2GHZ) {
                wl1271_debug(DEBUG_ACX, "using MIMO rate mask");
                /*
@@ -1478,7 +1486,7 @@ static int __devinit wl18xx_probe(struct platform_device *pdev)
                 * Only support mimo with multiple antennas. Fall back to
                 * siso20.
                 */
-               if (priv->conf.phy.number_of_assembled_ant2_4 >= 2)
+               if (wl18xx_is_mimo_supported(wl))
                        wlcore_set_ht_cap(wl, IEEE80211_BAND_2GHZ,
                                          &wl18xx_mimo_ht_cap_2ghz);
                else