return remaining;
}
-/* Handle physical or logical connection change events.
- * This routine is called when:
- * a port connection-change occurs;
- * a port enable-change occurs (often caused by EMI);
- * usb_reset_and_verify_device() encounters changed descriptors (as from
- * a firmware download)
- * caller already locked the hub
- */
-static void hub_port_connect_change(struct usb_hub *hub, int port1,
- u16 portstatus, u16 portchange)
+static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus,
+ u16 portchange)
{
+ int status, i;
+ unsigned unit_load;
struct usb_device *hdev = hub->hdev;
struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
struct usb_port *port_dev = hub->ports[port1 - 1];
- struct usb_device *udev;
- int status, i;
- unsigned unit_load;
-
- dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n",
- portstatus, portchange, portspeed(hub, portstatus));
-
- if (hub->has_indicators) {
- set_port_led(hub, port1, HUB_LED_AUTO);
- hub->indicator[port1-1] = INDICATOR_AUTO;
- }
-
-#ifdef CONFIG_USB_OTG
- /* during HNP, don't repeat the debounce */
- if (hdev->bus->is_b_host)
- portchange &= ~(USB_PORT_STAT_C_CONNECTION |
- USB_PORT_STAT_C_ENABLE);
-#endif
-
- /* Try to resuscitate an existing device */
- udev = port_dev->child;
- if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
- udev->state != USB_STATE_NOTATTACHED) {
- usb_lock_device(udev);
- if (portstatus & USB_PORT_STAT_ENABLE) {
- status = 0; /* Nothing to do */
-
-#ifdef CONFIG_PM_RUNTIME
- } else if (udev->state == USB_STATE_SUSPENDED &&
- udev->persist_enabled) {
- /* For a suspended device, treat this as a
- * remote wakeup event.
- */
- status = usb_remote_wakeup(udev);
-#endif
-
- } else {
- status = -ENODEV; /* Don't resuscitate */
- }
- usb_unlock_device(udev);
-
- if (status == 0) {
- clear_bit(port1, hub->change_bits);
- return;
- }
- }
+ struct usb_device *udev = port_dev->child;
/* Disconnect any existing devices under this port */
if (udev) {
usb_phy_notify_disconnect(hcd->phy, udev->speed);
usb_disconnect(&port_dev->child);
}
- clear_bit(port1, hub->change_bits);
/* We can forget about a "removed" device when there's a physical
* disconnect or the connect status changes.
hub_port_disable(hub, port1, 1);
if (hcd->driver->relinquish_port && !hub->hdev->parent)
hcd->driver->relinquish_port(hcd, port1);
+
+}
+
+/* Handle physical or logical connection change events.
+ * This routine is called when:
+ * a port connection-change occurs;
+ * a port enable-change occurs (often caused by EMI);
+ * usb_reset_and_verify_device() encounters changed descriptors (as from
+ * a firmware download)
+ * caller already locked the hub
+ */
+static void hub_port_connect_change(struct usb_hub *hub, int port1,
+ u16 portstatus, u16 portchange)
+{
+ struct usb_port *port_dev = hub->ports[port1 - 1];
+ struct usb_device *udev = port_dev->child;
+ int status = -ENODEV;
+
+ dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n", portstatus,
+ portchange, portspeed(hub, portstatus));
+
+ if (hub->has_indicators) {
+ set_port_led(hub, port1, HUB_LED_AUTO);
+ hub->indicator[port1-1] = INDICATOR_AUTO;
+ }
+
+#ifdef CONFIG_USB_OTG
+ /* during HNP, don't repeat the debounce */
+ if (hub->hdev->bus->is_b_host)
+ portchange &= ~(USB_PORT_STAT_C_CONNECTION |
+ USB_PORT_STAT_C_ENABLE);
+#endif
+
+ /* Try to resuscitate an existing device */
+ if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
+ udev->state != USB_STATE_NOTATTACHED) {
+ if (portstatus & USB_PORT_STAT_ENABLE) {
+ status = 0; /* Nothing to do */
+#ifdef CONFIG_PM_RUNTIME
+ } else if (udev->state == USB_STATE_SUSPENDED &&
+ udev->persist_enabled) {
+ /* For a suspended device, treat this as a
+ * remote wakeup event.
+ */
+ usb_lock_device(udev);
+ status = usb_remote_wakeup(udev);
+ usb_unlock_device(udev);
+#endif
+ } else {
+ /* Don't resuscitate */;
+ }
+
+ }
+ clear_bit(port1, hub->change_bits);
+
+ if (status == 0)
+ return;
+
+ hub_port_connect(hub, port1, portstatus, portchange);
}
/* Returns 1 if there was a remote wakeup and a connect status change. */
return connect_change;
}
+static void port_event(struct usb_hub *hub, int port1)
+{
+ int connect_change, reset_device = 0;
+ struct usb_port *port_dev = hub->ports[port1 - 1];
+ struct usb_device *udev = port_dev->child;
+ struct usb_device *hdev = hub->hdev;
+ u16 portstatus, portchange;
+
+ connect_change = test_bit(port1, hub->change_bits);
+ clear_bit(port1, hub->event_bits);
+ clear_bit(port1, hub->wakeup_bits);
+
+ if (hub_port_status(hub, port1, &portstatus, &portchange) < 0)
+ return;
+
+ if (portchange & USB_PORT_STAT_C_CONNECTION) {
+ usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_CONNECTION);
+ connect_change = 1;
+ }
+
+ if (portchange & USB_PORT_STAT_C_ENABLE) {
+ if (!connect_change)
+ dev_dbg(&port_dev->dev, "enable change, status %08x\n",
+ portstatus);
+ usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_ENABLE);
+
+ /*
+ * EM interference sometimes causes badly shielded USB devices
+ * to be shutdown by the hub, this hack enables them again.
+ * Works at least with mouse driver.
+ */
+ if (!(portstatus & USB_PORT_STAT_ENABLE)
+ && !connect_change && udev) {
+ dev_err(&port_dev->dev, "disabled by hub (EMI?), re-enabling...\n");
+ connect_change = 1;
+ }
+ }
+
+ if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
+ u16 status = 0, unused;
+
+ dev_dbg(&port_dev->dev, "over-current change\n");
+ usb_clear_port_feature(hdev, port1,
+ USB_PORT_FEAT_C_OVER_CURRENT);
+ msleep(100); /* Cool down */
+ hub_power_on(hub, true);
+ hub_port_status(hub, port1, &status, &unused);
+ if (status & USB_PORT_STAT_OVERCURRENT)
+ dev_err(&port_dev->dev, "over-current condition\n");
+ }
+
+ if (portchange & USB_PORT_STAT_C_RESET) {
+ dev_dbg(&port_dev->dev, "reset change\n");
+ usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_RESET);
+ }
+ if ((portchange & USB_PORT_STAT_C_BH_RESET)
+ && hub_is_superspeed(hdev)) {
+ dev_dbg(&port_dev->dev, "warm reset change\n");
+ usb_clear_port_feature(hdev, port1,
+ USB_PORT_FEAT_C_BH_PORT_RESET);
+ }
+ if (portchange & USB_PORT_STAT_C_LINK_STATE) {
+ dev_dbg(&port_dev->dev, "link state change\n");
+ usb_clear_port_feature(hdev, port1,
+ USB_PORT_FEAT_C_PORT_LINK_STATE);
+ }
+ if (portchange & USB_PORT_STAT_C_CONFIG_ERROR) {
+ dev_warn(&port_dev->dev, "config error\n");
+ usb_clear_port_feature(hdev, port1,
+ USB_PORT_FEAT_C_PORT_CONFIG_ERROR);
+ }
+
+ if (hub_handle_remote_wakeup(hub, port1, portstatus, portchange))
+ connect_change = 1;
+
+ /*
+ * Warm reset a USB3 protocol port if it's in
+ * SS.Inactive state.
+ */
+ if (hub_port_warm_reset_required(hub, portstatus)) {
+ dev_dbg(&port_dev->dev, "do warm reset\n");
+ if (!udev || !(portstatus & USB_PORT_STAT_CONNECTION)
+ || udev->state == USB_STATE_NOTATTACHED) {
+ if (hub_port_reset(hub, port1, NULL,
+ HUB_BH_RESET_TIME, true) < 0)
+ hub_port_disable(hub, port1, 1);
+ } else
+ reset_device = 1;
+ }
+
+ /*
+ * On disconnect USB3 protocol ports transit from U0 to
+ * SS.Inactive to Rx.Detect. If this happens a warm-
+ * reset is not needed, but a (re)connect may happen
+ * before khubd runs and sees the disconnect, and the
+ * device may be an unknown state.
+ *
+ * If the port went through SS.Inactive without khubd
+ * seeing it the C_LINK_STATE change flag will be set,
+ * and we reset the dev to put it in a known state.
+ */
+ if (reset_device || (udev && hub_is_superspeed(hub->hdev)
+ && (portchange & USB_PORT_STAT_C_LINK_STATE)
+ && (portstatus & USB_PORT_STAT_CONNECTION))) {
+ usb_lock_device(udev);
+ usb_reset_device(udev);
+ usb_unlock_device(udev);
+ connect_change = 0;
+ }
+
+ if (connect_change)
+ hub_port_connect_change(hub, port1, portstatus, portchange);
+}
+
+
static void hub_events(void)
{
struct list_head *tmp;
struct device *hub_dev;
u16 hubstatus;
u16 hubchange;
- u16 portstatus;
- u16 portchange;
int i, ret;
- int connect_change, wakeup_change;
/*
* We restart the list every time to avoid a deadlock with
/* deal with port status changes */
for (i = 1; i <= hdev->maxchild; i++) {
- struct usb_port *port_dev = hub->ports[i - 1];
- struct usb_device *udev = port_dev->child;
-
- if (test_bit(i, hub->busy_bits))
- continue;
- connect_change = test_bit(i, hub->change_bits);
- wakeup_change = test_and_clear_bit(i, hub->wakeup_bits);
- if (!test_and_clear_bit(i, hub->event_bits) &&
- !connect_change && !wakeup_change)
- continue;
-
- ret = hub_port_status(hub, i,
- &portstatus, &portchange);
- if (ret < 0)
- continue;
-
- if (portchange & USB_PORT_STAT_C_CONNECTION) {
- usb_clear_port_feature(hdev, i,
- USB_PORT_FEAT_C_CONNECTION);
- connect_change = 1;
- }
-
- if (portchange & USB_PORT_STAT_C_ENABLE) {
- if (!connect_change)
- dev_dbg(&port_dev->dev,
- "enable change, status %08x\n",
- portstatus);
- usb_clear_port_feature(hdev, i,
- USB_PORT_FEAT_C_ENABLE);
-
- /*
- * EM interference sometimes causes badly
- * shielded USB devices to be shutdown by
- * the hub, this hack enables them again.
- * Works at least with mouse driver.
- */
- if (!(portstatus & USB_PORT_STAT_ENABLE)
- && !connect_change && udev) {
- dev_err(&port_dev->dev,
- "disabled by hub (EMI?), re-enabling...\n");
- connect_change = 1;
- }
- }
-
- if (hub_handle_remote_wakeup(hub, i,
- portstatus, portchange))
- connect_change = 1;
-
- if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
- u16 status = 0;
- u16 unused;
-
- dev_dbg(&port_dev->dev, "over-current change\n");
- usb_clear_port_feature(hdev, i,
- USB_PORT_FEAT_C_OVER_CURRENT);
- msleep(100); /* Cool down */
- hub_power_on(hub, true);
- hub_port_status(hub, i, &status, &unused);
- if (status & USB_PORT_STAT_OVERCURRENT)
- dev_err(&port_dev->dev,
- "over-current condition\n");
- }
-
- if (portchange & USB_PORT_STAT_C_RESET) {
- dev_dbg(&port_dev->dev, "reset change\n");
- usb_clear_port_feature(hdev, i,
- USB_PORT_FEAT_C_RESET);
- }
- if ((portchange & USB_PORT_STAT_C_BH_RESET) &&
- hub_is_superspeed(hub->hdev)) {
- dev_dbg(&port_dev->dev, "warm reset change\n");
- usb_clear_port_feature(hdev, i,
- USB_PORT_FEAT_C_BH_PORT_RESET);
- }
- if (portchange & USB_PORT_STAT_C_LINK_STATE) {
- usb_clear_port_feature(hub->hdev, i,
- USB_PORT_FEAT_C_PORT_LINK_STATE);
- }
- if (portchange & USB_PORT_STAT_C_CONFIG_ERROR) {
- dev_warn(&port_dev->dev, "config error\n");
- usb_clear_port_feature(hub->hdev, i,
- USB_PORT_FEAT_C_PORT_CONFIG_ERROR);
- }
-
- /* Warm reset a USB3 protocol port if it's in
- * SS.Inactive state.
- */
- if (hub_port_warm_reset_required(hub, portstatus)) {
- int status;
-
- dev_dbg(&port_dev->dev, "warm reset\n");
- if (!udev ||
- !(portstatus & USB_PORT_STAT_CONNECTION) ||
- udev->state == USB_STATE_NOTATTACHED) {
- status = hub_port_reset(hub, i,
- NULL, HUB_BH_RESET_TIME,
- true);
- if (status < 0)
- hub_port_disable(hub, i, 1);
- } else {
- usb_lock_device(udev);
- status = usb_reset_device(udev);
- usb_unlock_device(udev);
- connect_change = 0;
- }
- /*
- * On disconnect USB3 protocol ports transit from U0 to
- * SS.Inactive to Rx.Detect. If this happens a warm-
- * reset is not needed, but a (re)connect may happen
- * before khubd runs and sees the disconnect, and the
- * device may be an unknown state.
- *
- * If the port went through SS.Inactive without khubd
- * seeing it the C_LINK_STATE change flag will be set,
- * and we reset the dev to put it in a known state.
- */
- } else if (udev && hub_is_superspeed(hub->hdev) &&
- (portchange & USB_PORT_STAT_C_LINK_STATE) &&
- (portstatus & USB_PORT_STAT_CONNECTION)) {
- usb_lock_device(udev);
- usb_reset_device(udev);
- usb_unlock_device(udev);
- connect_change = 0;
- }
-
- if (connect_change)
- hub_port_connect_change(hub, i,
- portstatus, portchange);
- } /* end for i */
+ if (!test_bit(i, hub->busy_bits)
+ && (test_bit(i, hub->event_bits)
+ || test_bit(i, hub->change_bits)
+ || test_bit(i, hub->wakeup_bits)))
+ port_event(hub, i);
+ }
/* deal with hub status changes */
if (test_and_clear_bit(0, hub->event_bits) == 0)
projects / users / willy / pagecache.git / commitdiff