The Coresight dummy source component is for the specific coresight source
devices kernel don't have permission to access or configure. For some SOCs,
there would be Coresight source trace components on sub-processor which
- are conneted to AP processor via debug bus. For these devices, a dummy driver
+ are connected to AP processor via debug bus. For these devices, a dummy driver
is needed to register them as Coresight source devices, so that paths can be
created in the driver. It provides Coresight API for operations on dummy
source devices, such as enabling and disabling them. It also provides the
This property is required in idle state nodes of device tree meant
for RISC-V systems. For more details on the suspend_type parameter
- refer the SBI specifiation v0.3 (or higher) [7].
+ refer the SBI specification v0.3 (or higher) [7].
local-timer-stop:
description:
description:
This binding extends the data mapping defined in lvds-data-mapping.yaml.
It supports reversing the bit order on the formats defined there in order
- to accomodate for even more specialized data formats, since a variety of
+ to accommodate for even more specialized data formats, since a variety of
data formats and layouts is used to drive LVDS displays.
properties:
memcpy channels in eDMA.
Notes:
-When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request
+When requesting channel via ti,dra7-dma-crossbar, the DMA client must request
the DMA event number as crossbar ID (input to the DMA crossbar).
For ti,am335x-edma-crossbar: the meaning of parameters of dmas for clients:
- st,irq{1,2}-disable: disable IRQ 1/2
- st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition
- st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition
- - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready contition
+ - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready condition
- st,irq{1,2}-click: raise IRQ 1/2 on click condition
- st,irq-open-drain: consider IRQ lines open-drain
- st,irq-active-low: make IRQ lines active low
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
- interrupt types other than PPI or PPIs that are not partitionned,
+ interrupt types other than PPI or PPIs that are not partitioned,
this cell must be zero. See the "ppi-partitions" node description
below.
IMAXled = 160000 * (592 / 600.5) * (1 / max-current-switch-number)
And the minimum output current formula:
IMINled = 3300 * (592 / 600.5) * (1 / max-current-switch-number)
- where max-current-switch-number is determinated by led configuration
+ where max-current-switch-number is determined by led configuration
and depends on how leds are physically connected to the led driver.
allOf:
number of completion messages for which FlexRM will inject
one MSI interrupt to CPU.
- The 3nd cell contains MSI timer value representing time for
+ The 3rd cell contains MSI timer value representing time for
which FlexRM will wait to accumulate N completion messages
where N is the value specified by 2nd cell above. If FlexRM
does not get required number of completion messages in time
can be connected to CMOS image sensors from various vendors, supporting both
MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2
or parallel. The hardware is capable of transmitting and receiving MIPI
- interlaved data strams with data types or multiple virtual channel
+ interleaved data streams with data types or multiple virtual channel
identifiers.
allOf:
$ref: /schemas/types.yaml#/definitions/uint32-array
maxItems: 2
description: |
- An array specyfing minimum image size in pixels at the FIMC input and
+ An array specifying minimum image size in pixels at the FIMC input and
output DMA, in the first and second cell respectively. Default value
is <16 16>.
description:
The PMIC provides intb and errb IRQ lines. The errb IRQ line is used
for fatal IRQs which will cause the PMIC to shut down power outputs.
- In many systems this will shut down the SoC contolling the PMIC and
+ In many systems this will shut down the SoC controlling the PMIC and
connecting/handling the errb can be omitted. However, there are cases
where the SoC is not powered by the PMIC or has a short time backup
energy to handle shutdown of critical hardware. In that case it may be
samsung,s2mps11-wrstbi-ground:
description: |
Indicates that WRSTBI pin of PMIC is pulled down. When the system is
- suspended it will always go down thus triggerring unwanted buck warm
+ suspended it will always go down thus triggering unwanted buck warm
reset (setting buck voltages to default values).
type: boolean
The TWL6040s are 8-channel high quality low-power audio codecs providing audio,
vibra and GPO functionality on OMAP4+ platforms.
-They are connected ot the host processor via i2c for commands, McPDM for audio
+They are connected to the host processor via i2c for commands, McPDM for audio
data and commands.
Required properties:
description: VDD_RFA_CMN supply regulator handle
vddrfa0p8-supply:
- description: VDD_RFA_0P8 suppply regulator handle
+ description: VDD_RFA_0P8 supply regulator handle
vddrfa1p7-supply:
description: VDD_RFA_1P7 supply regulator handle
3-tuple setting for each (up to 3) supported link
speed on the host. Range is 0 to 273000 in unit of
uV. Default is 0.
-- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of
+- apm,tx-pre-cursor2 : 2nd pre-cursor emphasis taps control. Two set of
3-tuple setting for each (up to 3) supported link
speed on the host. Range is 0 to 127400 in unit uV.
Default is 0x0.
description:
One instance of the T-PHY on MT7988 suffers from a performance
problem in 10GBase-R mode which needs a work-around in the driver.
- This flag enables a work-around ajusting an analog phy setting and
+ This flag enables a work-around adjusting an analog phy setting and
is required for XFI Port0 of the MT7988 SoC to be in compliance with
the SFP specification.
The force mode is used to manually switch the shared phy mode between
USB3 and PCIe, when USB3 phy type is selected by the consumer, and
force-mode is set, will cause phy's power and pipe toggled and force
- phy as USB3 mode which switched from default PCIe mode. But perfer to
+ phy as USB3 mode which switched from default PCIe mode. But prefer to
use the property "mediatek,syscon-type" for newer SoCs that support it.
type: boolean
qcom,tune-usb2-amplitude:
$ref: /schemas/types.yaml#/definitions/uint8
- description: High-Speed trasmit amplitude
+ description: High-Speed transmit amplitude
minimum: 0
maximum: 15
default: 8
- Alexandre TORGUE <alexandre.torgue@foss.st.com>
description: |
- STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
+ STMicroelectronics's STM32 MCUs integrate a GPIO and Pin mux/config hardware
controller. It controls the input/output settings on the available pins and
also provides ability to multiplex and configure the output of various
on-chip controllers onto these pads.
This macro is available here:
- include/dt-bindings/pinctrl/stm32-pinfunc.h
Some examples of using macro:
- /* GPIO A9 set as alernate function 2 */
+ /* GPIO A9 set as alternate function 2 */
... {
pinmux = <STM32_PINMUX('A', 9, AF2)>;
};
Each SCP core has own cache memory. The SRAM and L1TCM are shared by
cores. The power of cache, SRAM and L1TCM power should be enabled
before booting SCP cores. The size of cache, SRAM, and L1TCM are varied
- on differnt SoCs.
+ on different SoCs.
The SCP cores do not use an MMU, but has a set of registers to
control the translations between 32-bit CPU addresses into system bus
we use nvidia,adjust-baud-rates.
As an example, consider there is deviation observed in TX for baud rates as listed below. 0
- to 9600 has 1% deviation 9600 to 115200 2% deviation. This slight deviation is expcted and
+ to 9600 has 1% deviation 9600 to 115200 2% deviation. This slight deviation is expected and
Tegra UART is expected to handle it. Due to the issue stated above, baud rate on Tegra UART
should be set equal to or above deviation observed for avoiding frame errors. Property
should be set like this:
description: |
just the value of reg 57. Bit(3) decides whether the jack polarity is inverted.
Bit(2) decides whether the button on the headset is inverted.
- Bit(1)/(0) decides the mic properity to be OMTP/CTIA or auto.
+ Bit(1)/(0) decides the mic property to be OMTP/CTIA or auto.
minimum: 0x00
maximum: 0x0f
default: 0x0f
- st,odd-pwm-speed-mode:
If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
- channels. If not present, normal PWM spped mode (384 kHz) will be used.
+ channels. If not present, normal PWM speed mode (384 kHz) will be used.
- st,distortion-compensation:
If present, distortion compensation variable uses DCC coefficient.
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
- // Example 1 (new calbiration data: for pre v1 IP):
+ // Example 1 (new calibration data: for pre v1 IP):
thermal-sensor@4a9000 {
compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
reg = <0x4a9000 0x1000>, /* TM */
projects / linux.git / commitdiff