* Copyright (c) 2016 Microsemi Corporation
*/
+#include <linux/firmware.h>
+#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mdio.h>
#define DISABLE_HP_AUTO_MDIX_MASK 0x0080
#define DISABLE_PAIR_SWAP_CORR_MASK 0x0020
#define DISABLE_POLARITY_CORR_MASK 0x0010
+#define PARALLEL_DET_IGNORE_ADVERTISED 0x0008
+
+#define MSCC_PHY_EXT_CNTL_STATUS 22
+#define SMI_BROADCAST_WR_EN 0x0001
#define MSCC_PHY_ERR_RX_CNT 19
#define MSCC_PHY_ERR_FALSE_CARRIER_CNT 20
#define MAC_IF_SELECTION_RMII 1
#define MAC_IF_SELECTION_RGMII 2
#define MAC_IF_SELECTION_POS 11
+#define VSC8584_MAC_IF_SELECTION_MASK 0x1000
+#define VSC8584_MAC_IF_SELECTION_SGMII 0
+#define VSC8584_MAC_IF_SELECTION_1000BASEX 1
+#define VSC8584_MAC_IF_SELECTION_POS 12
#define FAR_END_LOOPBACK_MODE_MASK 0x0008
+#define MEDIA_OP_MODE_MASK 0x0700
+#define MEDIA_OP_MODE_COPPER 0
+#define MEDIA_OP_MODE_SERDES 1
+#define MEDIA_OP_MODE_1000BASEX 2
+#define MEDIA_OP_MODE_100BASEFX 3
+#define MEDIA_OP_MODE_AMS_COPPER_SERDES 5
+#define MEDIA_OP_MODE_AMS_COPPER_1000BASEX 6
+#define MEDIA_OP_MODE_AMS_COPPER_100BASEFX 7
+#define MEDIA_OP_MODE_POS 8
#define MII_VSC85XX_INT_MASK 25
#define MII_VSC85XX_INT_MASK_MASK 0xa000
#define MSCC_PHY_PAGE_STANDARD 0x0000 /* Standard registers */
#define MSCC_PHY_PAGE_EXTENDED 0x0001 /* Extended registers */
#define MSCC_PHY_PAGE_EXTENDED_2 0x0002 /* Extended reg - page 2 */
+#define MSCC_PHY_PAGE_EXTENDED_3 0x0003 /* Extended reg - page 3 */
+#define MSCC_PHY_PAGE_EXTENDED_4 0x0004 /* Extended reg - page 4 */
+/* Extended reg - GPIO; this is a bank of registers that are shared for all PHYs
+ * in the same package.
+ */
+#define MSCC_PHY_PAGE_EXTENDED_GPIO 0x0010 /* Extended reg - GPIO */
+#define MSCC_PHY_PAGE_TEST 0x2a30 /* Test reg */
#define MSCC_PHY_PAGE_TR 0x52b5 /* Token ring registers */
/* Extended Page 1 Registers */
#define FORCE_MDI_CROSSOVER_MDI 0x0008
#define MSCC_PHY_ACTIPHY_CNTL 20
+#define PHY_ADDR_REVERSED 0x0200
#define DOWNSHIFT_CNTL_MASK 0x001C
#define DOWNSHIFT_EN 0x0010
#define DOWNSHIFT_CNTL_POS 2
#define MSCC_PHY_EXT_PHY_CNTL_4 23
+#define PHY_CNTL_4_ADDR_POS 11
+
+#define MSCC_PHY_VERIPHY_CNTL_2 25
+
+#define MSCC_PHY_VERIPHY_CNTL_3 26
/* Extended Page 2 Registers */
+#define MSCC_PHY_CU_PMD_TX_CNTL 16
+
#define MSCC_PHY_RGMII_CNTL 20
#define RGMII_RX_CLK_DELAY_MASK 0x0070
#define RGMII_RX_CLK_DELAY_POS 4
#define SECURE_ON_ENABLE 0x8000
#define SECURE_ON_PASSWD_LEN_4 0x4000
+/* Extended Page 3 Registers */
+#define MSCC_PHY_SERDES_TX_VALID_CNT 21
+#define MSCC_PHY_SERDES_TX_CRC_ERR_CNT 22
+#define MSCC_PHY_SERDES_RX_VALID_CNT 28
+#define MSCC_PHY_SERDES_RX_CRC_ERR_CNT 29
+
+/* Extended page GPIO Registers */
+#define MSCC_DW8051_CNTL_STATUS 0
+#define MICRO_NSOFT_RESET 0x8000
+#define RUN_FROM_INT_ROM 0x4000
+#define AUTOINC_ADDR 0x2000
+#define PATCH_RAM_CLK 0x1000
+#define MICRO_PATCH_EN 0x0080
+#define DW8051_CLK_EN 0x0010
+#define MICRO_CLK_EN 0x0008
+#define MICRO_CLK_DIVIDE(x) ((x) >> 1)
+
+/* x Address in range 1-4 */
+#define MSCC_TRAP_ROM_ADDR(x) ((x) * 2 + 1)
+#define MSCC_PATCH_RAM_ADDR(x) (((x) + 1) * 2)
+#define MSCC_INT_MEM_ADDR 11
+
+#define MSCC_INT_MEM_CNTL 12
+#define READ_SFR 0x6000
+#define READ_PRAM 0x4000
+#define READ_ROM 0x2000
+#define READ_RAM 0x0000
+#define INT_MEM_WRITE_EN 0x1000
+#define EN_PATCH_RAM_TRAP_ADDR(x) (0x0100 << ((x) - 1))
+#define INT_MEM_DATA_M 0x00ff
+#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
+
+#define MSCC_PHY_PROC_CMD 18
+#define PROC_CMD_NCOMPLETED 0x8000
+#define PROC_CMD_FAILED 0x4000
+#define PROC_CMD_SGMII_PORT(x) ((x) << 8)
+#define PROC_CMD_FIBER_PORT(x) (0x0100 << (x) % 4)
+#define PROC_CMD_QSGMII_PORT 0x0c00
+#define PROC_CMD_RST_CONF_PORT 0x0080
+#define PROC_CMD_RECONF_PORT 0x0000
+#define PROC_CMD_READ_MOD_WRITE_PORT 0x0040
+#define PROC_CMD_WRITE 0x0040
+#define PROC_CMD_READ 0x0000
+#define PROC_CMD_FIBER_DISABLE 0x0020
+#define PROC_CMD_FIBER_100BASE_FX 0x0010
+#define PROC_CMD_FIBER_1000BASE_X 0x0000
+#define PROC_CMD_SGMII_MAC 0x0030
+#define PROC_CMD_QSGMII_MAC 0x0020
+#define PROC_CMD_NO_MAC_CONF 0x0000
+#define PROC_CMD_NOP 0x000f
+#define PROC_CMD_CRC16 0x0008
+#define PROC_CMD_FIBER_MEDIA_CONF 0x0001
+#define PROC_CMD_MCB_ACCESS_MAC_CONF 0x0000
+#define PROC_CMD_NCOMPLETED_TIMEOUT_MS 500
+
+#define MSCC_PHY_MAC_CFG_FASTLINK 19
+#define MAC_CFG_MASK 0xc000
+#define MAC_CFG_SGMII 0x0000
+#define MAC_CFG_QSGMII 0x4000
+
+/* Test page Registers */
+#define MSCC_PHY_TEST_PAGE_5 5
+#define MSCC_PHY_TEST_PAGE_8 8
+
/* Token ring page Registers */
#define MSCC_PHY_TR_CNTL 16
#define TR_WRITE 0x8000
#define PHY_ID_VSC8531 0x00070570
#define PHY_ID_VSC8540 0x00070760
#define PHY_ID_VSC8541 0x00070770
+#define PHY_ID_VSC8584 0x000707c0
#define MSCC_VDDMAC_1500 1500
#define MSCC_VDDMAC_1800 1800
#define DOWNSHIFT_COUNT_MAX 5
#define MAX_LEDS 4
+
+#define VSC8584_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
+ BIT(VSC8531_LINK_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_100_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_ACTIVITY) | \
+ BIT(VSC8531_LINK_100_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_100_ACTIVITY) | \
+ BIT(VSC8584_LINK_100FX_1000X_ACTIVITY) | \
+ BIT(VSC8531_DUPLEX_COLLISION) | \
+ BIT(VSC8531_COLLISION) | \
+ BIT(VSC8531_ACTIVITY) | \
+ BIT(VSC8584_100FX_1000X_ACTIVITY) | \
+ BIT(VSC8531_AUTONEG_FAULT) | \
+ BIT(VSC8531_SERIAL_MODE) | \
+ BIT(VSC8531_FORCE_LED_OFF) | \
+ BIT(VSC8531_FORCE_LED_ON))
+
#define VSC85XX_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
BIT(VSC8531_LINK_1000_ACTIVITY) | \
BIT(VSC8531_LINK_100_ACTIVITY) | \
BIT(VSC8531_FORCE_LED_OFF) | \
BIT(VSC8531_FORCE_LED_ON))
+#define MSCC_VSC8584_REVB_INT8051_FW "mscc_vsc8584_revb_int8051_fb48.bin"
+#define MSCC_VSC8584_REVB_INT8051_FW_START_ADDR 0xe800
+#define MSCC_VSC8584_REVB_INT8051_FW_CRC 0xfb48
+
+#define VSC8584_REVB 0x0001
+#define MSCC_DEV_REV_MASK GENMASK(3, 0)
+
struct reg_val {
u16 reg;
u32 val;
},
};
+static const struct vsc85xx_hw_stat vsc8584_hw_stats[] = {
+ {
+ .string = "phy_receive_errors",
+ .reg = MSCC_PHY_ERR_RX_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_false_carrier",
+ .reg = MSCC_PHY_ERR_FALSE_CARRIER_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_cu_media_link_disconnect",
+ .reg = MSCC_PHY_ERR_LINK_DISCONNECT_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_cu_media_crc_good_count",
+ .reg = MSCC_PHY_CU_MEDIA_CRC_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_cu_media_crc_error_count",
+ .reg = MSCC_PHY_EXT_PHY_CNTL_4,
+ .page = MSCC_PHY_PAGE_EXTENDED,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_serdes_tx_good_pkt_count",
+ .reg = MSCC_PHY_SERDES_TX_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_serdes_tx_bad_crc_count",
+ .reg = MSCC_PHY_SERDES_TX_CRC_ERR_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_serdes_rx_good_pkt_count",
+ .reg = MSCC_PHY_SERDES_RX_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_serdes_rx_bad_crc_count",
+ .reg = MSCC_PHY_SERDES_RX_CRC_ERR_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = ERR_CNT_MASK,
+ },
+};
+
struct vsc8531_private {
int rate_magic;
u16 supp_led_modes;
const struct vsc85xx_hw_stat *hw_stats;
u64 *stats;
int nstats;
+ bool pkg_init;
+ /* For multiple port PHYs; the MDIO address of the base PHY in the
+ * package.
+ */
+ unsigned int base_addr;
};
#ifdef CONFIG_OF_MDIO
return oldpage;
}
+/* phydev->bus->mdio_lock should be locked when using this function */
+static int phy_base_write(struct phy_device *phydev, u32 regnum, u16 val)
+{
+ struct vsc8531_private *priv = phydev->priv;
+
+ if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
+ dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
+ dump_stack();
+ }
+
+ return __mdiobus_write(phydev->mdio.bus, priv->base_addr, regnum, val);
+}
+
+/* phydev->bus->mdio_lock should be locked when using this function */
+static int phy_base_read(struct phy_device *phydev, u32 regnum)
+{
+ struct vsc8531_private *priv = phydev->priv;
+
+ if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
+ dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
+ dump_stack();
+ }
+
+ return __mdiobus_read(phydev->mdio.bus, priv->base_addr, regnum);
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static void vsc8584_csr_write(struct phy_device *phydev, u16 addr, u32 val)
+{
+ phy_base_write(phydev, MSCC_PHY_TR_MSB, val >> 16);
+ phy_base_write(phydev, MSCC_PHY_TR_LSB, val & GENMASK(15, 0));
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_cmd(struct phy_device *phydev, u16 val)
+{
+ unsigned long deadline;
+ u16 reg_val;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NCOMPLETED | val);
+
+ deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
+ do {
+ reg_val = phy_base_read(phydev, MSCC_PHY_PROC_CMD);
+ } while (time_before(jiffies, deadline) &&
+ (reg_val & PROC_CMD_NCOMPLETED) &&
+ !(reg_val & PROC_CMD_FAILED));
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ if (reg_val & PROC_CMD_FAILED)
+ return -EIO;
+
+ if (reg_val & PROC_CMD_NCOMPLETED)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_micro_deassert_reset(struct phy_device *phydev,
+ bool patch_en)
+{
+ u32 enable, release;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ enable = RUN_FROM_INT_ROM | MICRO_CLK_EN | DW8051_CLK_EN;
+ release = MICRO_NSOFT_RESET | RUN_FROM_INT_ROM | DW8051_CLK_EN |
+ MICRO_CLK_EN;
+
+ if (patch_en) {
+ enable |= MICRO_PATCH_EN;
+ release |= MICRO_PATCH_EN;
+
+ /* Clear all patches */
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
+ }
+
+ /* Enable 8051 Micro clock; CLEAR/SET patch present; disable PRAM clock
+ * override and addr. auto-incr; operate at 125 MHz
+ */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, enable);
+ /* Release 8051 Micro SW reset */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, release);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_micro_assert_reset(struct phy_device *phydev)
+{
+ int ret;
+ u16 reg;
+
+ ret = vsc8584_cmd(phydev, PROC_CMD_NOP);
+ if (ret)
+ return ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_TRAP_ROM_ADDR(4), 0x005b);
+ phy_base_write(phydev, MSCC_PATCH_RAM_ADDR(4), 0x005b);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg |= EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NOP);
+
+ reg = phy_base_read(phydev, MSCC_DW8051_CNTL_STATUS);
+ reg &= ~MICRO_NSOFT_RESET;
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, reg);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_MCB_ACCESS_MAC_CONF |
+ PROC_CMD_SGMII_PORT(0) | PROC_CMD_NO_MAC_CONF |
+ PROC_CMD_READ);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_get_fw_crc(struct phy_device *phydev, u16 start, u16 size,
+ u16 *crc)
+{
+ int ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+
+ phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_2, start);
+ phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_3, size);
+
+ /* Start Micro command */
+ ret = vsc8584_cmd(phydev, PROC_CMD_CRC16);
+ if (ret)
+ goto out;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+
+ *crc = phy_base_read(phydev, MSCC_PHY_VERIPHY_CNTL_2);
+
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return ret;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_patch_fw(struct phy_device *phydev,
+ const struct firmware *fw)
+{
+ int i, ret;
+
+ ret = vsc8584_micro_assert_reset(phydev);
+ if (ret) {
+ dev_err(&phydev->mdio.dev,
+ "%s: failed to assert reset of micro\n", __func__);
+ return ret;
+ }
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ /* Hold 8051 Micro in SW Reset, Enable auto incr address and patch clock
+ * Disable the 8051 Micro clock
+ */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, RUN_FROM_INT_ROM |
+ AUTOINC_ADDR | PATCH_RAM_CLK | MICRO_CLK_EN |
+ MICRO_CLK_DIVIDE(2));
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM | INT_MEM_WRITE_EN |
+ INT_MEM_DATA(2));
+ phy_base_write(phydev, MSCC_INT_MEM_ADDR, 0x0000);
+
+ for (i = 0; i < fw->size; i++)
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM |
+ INT_MEM_WRITE_EN | fw->data[i]);
+
+ /* Clear internal memory access */
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_config_pre_init(struct phy_device *phydev)
+{
+ const struct reg_val pre_init1[] = {
+ {0x07fa, 0x0050100f},
+ {0x1688, 0x00049f81},
+ {0x0f90, 0x00688980},
+ {0x03a4, 0x0000d8f0},
+ {0x0fc0, 0x00000400},
+ {0x0f82, 0x0012b002},
+ {0x1686, 0x00000004},
+ {0x168c, 0x00d2c46f},
+ {0x17a2, 0x00000620},
+ {0x16a0, 0x00eeffdd},
+ {0x16a6, 0x00071448},
+ {0x16a4, 0x0013132f},
+ {0x16a8, 0x00000000},
+ {0x0ffc, 0x00c0a028},
+ {0x0fe8, 0x0091b06c},
+ {0x0fea, 0x00041600},
+ {0x0f80, 0x00fffaff},
+ {0x0fec, 0x00901809},
+ {0x0ffe, 0x00b01007},
+ {0x16b0, 0x00eeff00},
+ {0x16b2, 0x00007000},
+ {0x16b4, 0x00000814},
+ };
+ const struct reg_val pre_init2[] = {
+ {0x0486, 0x0008a518},
+ {0x0488, 0x006dc696},
+ {0x048a, 0x00000912},
+ };
+ const struct firmware *fw;
+ struct device *dev = &phydev->mdio.dev;
+ unsigned int i;
+ u16 crc, reg;
+ int ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* all writes below are broadcasted to all PHYs in the same package */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg |= SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ phy_base_write(phydev, MII_VSC85XX_INT_MASK, 0);
+
+ reg = phy_base_read(phydev, MSCC_PHY_BYPASS_CONTROL);
+ reg |= PARALLEL_DET_IGNORE_ADVERTISED;
+ phy_base_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg);
+
+ /* The below register writes are tweaking analog and electrical
+ * configuration that were determined through characterization by PHY
+ * engineers. These don't mean anything more than "these are the best
+ * values".
+ */
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_3);
+
+ phy_base_write(phydev, MSCC_PHY_SERDES_TX_CRC_ERR_CNT, 0x2000);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_5, 0x1f20);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg |= 0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x2fa4));
+
+ reg = phy_base_read(phydev, MSCC_PHY_TR_MSB);
+ reg &= ~0x007f;
+ reg |= 0x0019;
+ phy_base_write(phydev, MSCC_PHY_TR_MSB, reg);
+
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x0fa4));
+
+ for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
+ vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_2);
+
+ phy_base_write(phydev, MSCC_PHY_CU_PMD_TX_CNTL, 0x028e);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ for (i = 0; i < ARRAY_SIZE(pre_init2); i++)
+ vsc8584_csr_write(phydev, pre_init2[i].reg, pre_init2[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg &= ~0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* end of write broadcasting */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg &= ~SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ ret = request_firmware(&fw, MSCC_VSC8584_REVB_INT8051_FW, dev);
+ if (ret) {
+ dev_err(dev, "failed to load firmware %s, ret: %d\n",
+ MSCC_VSC8584_REVB_INT8051_FW, ret);
+ return ret;
+ }
+
+ /* Add one byte to size for the one added by the patch_fw function */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC) {
+ dev_dbg(dev, "FW CRC is not the expected one, patching FW\n");
+ if (vsc8584_patch_fw(phydev, fw))
+ dev_warn(dev,
+ "failed to patch FW, expect non-optimal device\n");
+ }
+
+ vsc8584_micro_deassert_reset(phydev, false);
+
+ /* Add one byte to size for the one added by the patch_fw function */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC)
+ dev_warn(dev,
+ "FW CRC after patching is not the expected one, expect non-optimal device\n");
+
+ ret = vsc8584_micro_assert_reset(phydev);
+ if (ret)
+ goto out;
+
+ vsc8584_micro_deassert_reset(phydev, true);
+
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ release_firmware(fw);
+
+ return ret;
+}
+
+/* Check if one PHY has already done the init of the parts common to all PHYs
+ * in the Quad PHY package.
+ */
+static bool vsc8584_is_pkg_init(struct phy_device *phydev, bool reversed)
+{
+ struct mdio_device **map = phydev->mdio.bus->mdio_map;
+ struct vsc8531_private *vsc8531;
+ struct phy_device *phy;
+ int i, addr;
+
+ /* VSC8584 is a Quad PHY */
+ for (i = 0; i < 4; i++) {
+ vsc8531 = phydev->priv;
+
+ if (reversed)
+ addr = vsc8531->base_addr - i;
+ else
+ addr = vsc8531->base_addr + i;
+
+ phy = container_of(map[addr], struct phy_device, mdio);
+
+ if ((phy->phy_id & phydev->drv->phy_id_mask) !=
+ (phydev->drv->phy_id & phydev->drv->phy_id_mask))
+ continue;
+
+ vsc8531 = phy->priv;
+
+ if (vsc8531 && vsc8531->pkg_init)
+ return true;
+ }
+
+ return false;
+}
+
+static int vsc8584_config_init(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531 = phydev->priv;
+ u16 addr, val;
+ int ret, i;
+
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
+ mutex_lock(&phydev->mdio.bus->mdio_lock);
+
+ __mdiobus_write(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+ addr = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_PHY_EXT_PHY_CNTL_4);
+ addr >>= PHY_CNTL_4_ADDR_POS;
+
+ val = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_PHY_ACTIPHY_CNTL);
+ if (val & PHY_ADDR_REVERSED)
+ vsc8531->base_addr = phydev->mdio.addr + addr;
+ else
+ vsc8531->base_addr = phydev->mdio.addr - addr;
+
+ /* Some parts of the init sequence are identical for every PHY in the
+ * package. Some parts are modifying the GPIO register bank which is a
+ * set of registers that are affecting all PHYs, a few resetting the
+ * microprocessor common to all PHYs. The CRC check responsible of the
+ * checking the firmware within the 8051 microprocessor can only be
+ * accessed via the PHY whose internal address in the package is 0.
+ * All PHYs' interrupts mask register has to be zeroed before enabling
+ * any PHY's interrupt in this register.
+ * For all these reasons, we need to do the init sequence once and only
+ * once whatever is the first PHY in the package that is initialized and
+ * do the correct init sequence for all PHYs that are package-critical
+ * in this pre-init function.
+ */
+ if (!vsc8584_is_pkg_init(phydev, val & PHY_ADDR_REVERSED ? 1 : 0)) {
+ ret = vsc8584_config_pre_init(phydev);
+ if (ret)
+ goto err;
+ }
+
+ vsc8531->pkg_init = true;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ val = phy_base_read(phydev, MSCC_PHY_MAC_CFG_FASTLINK);
+ val &= ~MAC_CFG_MASK;
+ if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
+ val |= MAC_CFG_QSGMII;
+ else
+ val |= MAC_CFG_SGMII;
+
+ ret = phy_base_write(phydev, MSCC_PHY_MAC_CFG_FASTLINK, val);
+ if (ret)
+ goto err;
+
+ val = PROC_CMD_MCB_ACCESS_MAC_CONF | PROC_CMD_RST_CONF_PORT |
+ PROC_CMD_READ_MOD_WRITE_PORT;
+ if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
+ val |= PROC_CMD_QSGMII_MAC;
+ else
+ val |= PROC_CMD_SGMII_MAC;
+
+ ret = vsc8584_cmd(phydev, val);
+ if (ret)
+ goto err;
+
+ usleep_range(10000, 20000);
+
+ /* Disable SerDes for 100Base-FX */
+ ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
+ PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
+ PROC_CMD_READ_MOD_WRITE_PORT |
+ PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_100BASE_FX);
+ if (ret)
+ goto err;
+
+ /* Disable SerDes for 1000Base-X */
+ ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
+ PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
+ PROC_CMD_READ_MOD_WRITE_PORT |
+ PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_1000BASE_X);
+ if (ret)
+ goto err;
+
+ mutex_unlock(&phydev->mdio.bus->mdio_lock);
+
+ phy_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
+ val &= ~(MEDIA_OP_MODE_MASK | VSC8584_MAC_IF_SELECTION_MASK);
+ val |= MEDIA_OP_MODE_COPPER | (VSC8584_MAC_IF_SELECTION_SGMII <<
+ VSC8584_MAC_IF_SELECTION_POS);
+ ret = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, val);
+
+ ret = genphy_soft_reset(phydev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < vsc8531->nleds; i++) {
+ ret = vsc85xx_led_cntl_set(phydev, i, vsc8531->leds_mode[i]);
+ if (ret)
+ return ret;
+ }
+
+ return genphy_config_init(phydev);
+
+err:
+ mutex_unlock(&phydev->mdio.bus->mdio_lock);
+ return ret;
+}
+
static int vsc85xx_config_init(struct phy_device *phydev)
{
int rc, i;
return genphy_config_init(phydev);
}
+static int vsc8584_did_interrupt(struct phy_device *phydev)
+{
+ int rc = 0;
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ rc = phy_read(phydev, MII_VSC85XX_INT_STATUS);
+
+ return (rc < 0) ? 0 : rc & MII_VSC85XX_INT_MASK_MASK;
+}
+
static int vsc85xx_ack_interrupt(struct phy_device *phydev)
{
int rc = 0;
return genphy_read_status(phydev);
}
+static int vsc8584_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
+ VSC8531_DUPLEX_COLLISION};
+
+ if ((phydev->phy_id & MSCC_DEV_REV_MASK) != VSC8584_REVB) {
+ dev_err(&phydev->mdio.dev, "Only VSC8584 revB is supported.\n");
+ return -ENOTSUPP;
+ }
+
+ vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
+ if (!vsc8531)
+ return -ENOMEM;
+
+ phydev->priv = vsc8531;
+
+ vsc8531->nleds = 4;
+ vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
+ vsc8531->hw_stats = vsc8584_hw_stats;
+ vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
+ vsc8531->stats = devm_kmalloc_array(&phydev->mdio.dev, vsc8531->nstats,
+ sizeof(u64), GFP_KERNEL);
+ if (!vsc8531->stats)
+ return -ENOMEM;
+
+ return vsc85xx_dt_led_modes_get(phydev, default_mode);
+}
+
static int vsc85xx_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
+},
+{
+ .phy_id = PHY_ID_VSC8584,
+ .name = "Microsemi GE VSC8584 SyncE",
+ .phy_id_mask = 0xfffffff0,
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .soft_reset = &genphy_soft_reset,
+ .config_init = &vsc8584_config_init,
+ .config_aneg = &vsc85xx_config_aneg,
+ .aneg_done = &genphy_aneg_done,
+ .read_status = &vsc85xx_read_status,
+ .ack_interrupt = &vsc85xx_ack_interrupt,
+ .config_intr = &vsc85xx_config_intr,
+ .did_interrupt = &vsc8584_did_interrupt,
+ .suspend = &genphy_suspend,
+ .resume = &genphy_resume,
+ .probe = &vsc8584_probe,
+ .get_tunable = &vsc85xx_get_tunable,
+ .set_tunable = &vsc85xx_set_tunable,
+ .read_page = &vsc85xx_phy_read_page,
+ .write_page = &vsc85xx_phy_write_page,
+ .get_sset_count = &vsc85xx_get_sset_count,
+ .get_strings = &vsc85xx_get_strings,
+ .get_stats = &vsc85xx_get_stats,
}
};
{ PHY_ID_VSC8531, 0xfffffff0, },
{ PHY_ID_VSC8540, 0xfffffff0, },
{ PHY_ID_VSC8541, 0xfffffff0, },
+ { PHY_ID_VSC8584, 0xfffffff0, },
{ }
};
projects / users / hch / xfs.git / commitdiff