phy: miphy28lp: Add SSC support for PCIE

SSC is the technique of modulating the operating frequency of a signal
slightly to spread its radiated emissions over a range of frequencies.
This reduction in the maximum emission for a given frequency helps meet
radiated emission requirements.
These settings are applicable for PCIE with Internal clock.

Signed-off-by: Harsh Gupta <harsh.gupta@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

diff --git a/drivers/phy/phy-miphy28lp.c b/drivers/phy/phy-miphy28lp.c
index d2f797c79fbcd2989833d7d788dfd474b65a702e..d8ff8956ed056aa6b8422d1e457491fc7650843e 100644 (file)
--- a/drivers/phy/phy-miphy28lp.c
+++ b/drivers/phy/phy-miphy28lp.c
@@ -192,6 +192,7 @@
 #define SATA_SPDMODE           1
 
 #define MIPHY_SATA_BANK_NB     3
+#define MIPHY_PCIE_BANK_NB     2
 
 struct miphy28lp_phy {
        struct phy *phy;
@@ -591,6 +592,46 @@ static void miphy_sata_tune_ssc(struct miphy28lp_phy *miphy_phy)
        }
 }
 
+static void miphy_pcie_tune_ssc(struct miphy28lp_phy *miphy_phy)
+{
+       void __iomem *base = miphy_phy->base;
+       u8 val;
+
+       /* Compensate Tx impedance to avoid out of range values */
+       /*
+        * Enable the SSC on PLL for all banks
+        * SSC Modulation @ 31 KHz and 4000 ppm modulation amp
+        */
+       val = readb_relaxed(base + MIPHY_BOUNDARY_2);
+       val |= SSC_EN_SW;
+       writeb_relaxed(val, base + MIPHY_BOUNDARY_2);
+
+       val = readb_relaxed(base + MIPHY_BOUNDARY_SEL);
+       val |= SSC_SEL;
+       writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+       for (val = 0; val < MIPHY_PCIE_BANK_NB; val++) {
+               writeb_relaxed(val, base + MIPHY_CONF);
+
+               /* Validate Step component */
+               writeb_relaxed(0x69, base + MIPHY_PLL_SBR_3);
+               writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+               /* Validate Period component */
+               writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+               writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+               /* Clear any previous request */
+               writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+               /* requests the PLL to take in account new parameters */
+               writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+               /* To be sure there is no other pending requests */
+               writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+       }
+}
+
 static inline int miphy28lp_configure_sata(struct miphy28lp_phy *miphy_phy)
 {
        void __iomem *base = miphy_phy->base;
@@ -659,6 +700,9 @@ static inline int miphy28lp_configure_pcie(struct miphy28lp_phy *miphy_phy)
        if (err)
                return err;
 
+       if (miphy_phy->ssc)
+               miphy_pcie_tune_ssc(miphy_phy);
+
        return 0;
 }