staging: wilc1000: remove the warnings on missing blank line

This patch removes the warnings reported by checkpatch.pl on missing a blank
line after declaration.

Signed-off-by: Tony Cho <tony.cho@atmel.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/wilc1000/wilc_sdio.c b/drivers/staging/wilc1000/wilc_sdio.c
index 632b2b081fc67390e69d04cb7a07381b7744a2e2..6e865d417efbf3f05281f5c0380e4fac0d078916 100644 (file)
--- a/drivers/staging/wilc1000/wilc_sdio.c
+++ b/drivers/staging/wilc1000/wilc_sdio.c
@@ -168,6 +168,7 @@ static int sdio_clear_int(void)
 #ifndef WILC_SDIO_IRQ_GPIO
        /* uint32_t sts; */
        sdio_cmd52_t cmd;
+
        cmd.read_write = 0;
        cmd.function = 1;
        cmd.raw = 0;
@@ -179,6 +180,7 @@ static int sdio_clear_int(void)
        return cmd.data;
 #else
        uint32_t reg;
+
        if (!sdio_read_reg(WILC_HOST_RX_CTRL_0, &reg)) {
                g_sdio.dPrint(N_ERR, "[wilc spi]: Failed read reg (%08x)...\n", WILC_HOST_RX_CTRL_0);
                return 0;
@@ -195,6 +197,7 @@ uint32_t sdio_xfer_cnt(void)
 {
        uint32_t cnt = 0;
        sdio_cmd52_t cmd;
+
        cmd.read_write = 0;
        cmd.function = 1;
        cmd.raw = 0;
@@ -259,6 +262,7 @@ static int sdio_write_reg(uint32_t addr, uint32_t data)
 
        if ((addr >= 0xf0) && (addr <= 0xff)) {
                sdio_cmd52_t cmd;
+
                cmd.read_write = 1;
                cmd.function = 0;
                cmd.raw = 0;
@@ -482,6 +486,7 @@ static int sdio_read_reg(uint32_t addr, uint32_t *data)
 {
        if ((addr >= 0xf0) && (addr <= 0xff)) {
                sdio_cmd52_t cmd;
+
                cmd.read_write = 0;
                cmd.function = 0;
                cmd.raw = 0;
@@ -776,6 +781,7 @@ static int sdio_init(wilc_wlan_inp_t *inp, wilc_debug_func func)
        sdio_cmd52_t cmd;
        int loop;
        uint32_t chipid;
+
        memset(&g_sdio, 0, sizeof(wilc_sdio_t));
 
        g_sdio.dPrint = func;
@@ -977,6 +983,7 @@ static int sdio_read_int(uint32_t *int_status)
        }
        {
                int i;
+
                for (i = g_sdio.nint; i < MAX_NUM_INT; i++) {
                        if ((tmp >> (IRG_FLAGS_OFFSET + i)) & 0x1) {
                                g_sdio.dPrint(N_ERR, "[wilc sdio]: Unexpected interrupt (1) : tmp=%x, data=%x\n", tmp, cmd.data);
@@ -1015,6 +1022,7 @@ static int sdio_clear_int_ext(uint32_t val)
 #ifdef WILC_SDIO_IRQ_GPIO
                {
                        uint32_t flags;
+
                        flags = val & ((1 << MAX_NUN_INT_THRPT_ENH2) - 1);
                        reg = flags;
                }
@@ -1032,6 +1040,7 @@ static int sdio_clear_int_ext(uint32_t val)
                        reg |= (1 << 7);
                if (reg) {
                        sdio_cmd52_t cmd;
+
                        cmd.read_write = 1;
                        cmd.function = 0;
                        cmd.raw = 0;
@@ -1051,6 +1060,7 @@ static int sdio_clear_int_ext(uint32_t val)
                        /* see below. has_thrpt_enh2 uses register 0xf8 to clear interrupts. */
                        /* Cannot clear multiple interrupts. Must clear each interrupt individually */
                        uint32_t flags;
+
                        flags = val & ((1 << MAX_NUM_INT) - 1);
                        if (flags) {
                                int i;
@@ -1059,6 +1069,7 @@ static int sdio_clear_int_ext(uint32_t val)
                                for (i = 0; i < g_sdio.nint; i++) {
                                        if (flags & 1) {
                                                sdio_cmd52_t cmd;
+
                                                cmd.read_write = 1;
                                                cmd.function = 0;
                                                cmd.raw = 0;