x86/nmi/64: Use DF to avoid userspace RSP confusing nested NMI detection

We have a tricky bug in the nested NMI code: if we see RSP
pointing to the NMI stack on NMI entry from kernel mode, we
assume that we are executing a nested NMI.

This isn't quite true.  A malicious userspace program can point
RSP at the NMI stack, issue SYSCALL, and arrange for an NMI to
happen while RSP is still pointing at the NMI stack.

Fix it with a sneaky trick.  Set DF in the region of code that
the RSP check is intended to detect.  IRET will clear DF
atomically.

( Note: other than paravirt, there's little need for all this
  complexity. We could check RIP instead of RSP. )

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

diff --git a/arch/x86/entry/entry_64.S b/arch/x86/entry/entry_64.S
index 5c4ab384b84f176e16e56771ccf76818cb295599..d8ab2b201fa197c05f24ca3361c94169123cbca4 100644 (file)
--- a/arch/x86/entry/entry_64.S
+++ b/arch/x86/entry/entry_64.S
@@ -1388,7 +1388,14 @@ ENTRY(nmi)
        /*
         * Now test if the previous stack was an NMI stack.  This covers
         * the case where we interrupt an outer NMI after it clears
-        * "NMI executing" but before IRET.
+        * "NMI executing" but before IRET.  We need to be careful, though:
+        * there is one case in which RSP could point to the NMI stack
+        * despite there being no NMI active: naughty userspace controls
+        * RSP at the very beginning of the SYSCALL targets.  We can
+        * pull a fast one on naughty userspace, though: we program
+        * SYSCALL to mask DF, so userspace cannot cause DF to be set
+        * if it controls the kernel's RSP.  We set DF before we clear
+        * "NMI executing".
         */
        lea     6*8(%rsp), %rdx
        /* Compare the NMI stack (rdx) with the stack we came from (4*8(%rsp)) */
@@ -1400,7 +1407,13 @@ ENTRY(nmi)
        cmpq    %rdx, 4*8(%rsp)
        /* If it is below the NMI stack, it is a normal NMI */
        jb      first_nmi
-       /* Ah, it is within the NMI stack, treat it as nested */
+
+       /* Ah, it is within the NMI stack. */
+
+       testb   $(X86_EFLAGS_DF >> 8), (3*8 + 1)(%rsp)
+       jz      first_nmi       /* RSP was user controlled. */
+
+       /* This is a nested NMI. */
 
 nested_nmi:
        /*
@@ -1506,8 +1519,16 @@ nmi_restore:
        /* Point RSP at the "iret" frame. */
        REMOVE_PT_GPREGS_FROM_STACK 6*8
 
-       /* Clear "NMI executing". */
-       movq    $0, 5*8(%rsp)
+       /*
+        * Clear "NMI executing".  Set DF first so that we can easily
+        * distinguish the remaining code between here and IRET from
+        * the SYSCALL entry and exit paths.  On a native kernel, we
+        * could just inspect RIP, but, on paravirt kernels,
+        * INTERRUPT_RETURN can translate into a jump into a
+        * hypercall page.
+        */
+       std
+       movq    $0, 5*8(%rsp)           /* clear "NMI executing" */
 
        /*
         * INTERRUPT_RETURN reads the "iret" frame and exits the NMI