*/
#define AT91_ECC (0xffffe200 - AT91_BASE_SYS)
#define AT91_BCRAMC (0xffffe400 - AT91_BASE_SYS)
-#define AT91_DDRSDRC (0xffffe600 - AT91_BASE_SYS)
+#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
#define AT91_SMC (0xffffe800 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS)
#define AT91_CCFG (0xffffeb10 - AT91_BASE_SYS)
#ifndef AT91CAP9_DDRSDR_H
#define AT91CAP9_DDRSDR_H
-#define AT91_DDRSDRC_MR (AT91_DDRSDRC + 0x00) /* Mode Register */
+#define AT91_DDRSDRC_MR 0x00 /* Mode Register */
#define AT91_DDRSDRC_MODE (0xf << 0) /* Command Mode */
#define AT91_DDRSDRC_MODE_NORMAL 0
#define AT91_DDRSDRC_MODE_NOP 1
#define AT91_DDRSDRC_MODE_EXT_LMR 5
#define AT91_DDRSDRC_MODE_DEEP 6
-#define AT91_DDRSDRC_RTR (AT91_DDRSDRC + 0x04) /* Refresh Timer Register */
+#define AT91_DDRSDRC_RTR 0x04 /* Refresh Timer Register */
#define AT91_DDRSDRC_COUNT (0xfff << 0) /* Refresh Timer Counter */
-#define AT91_DDRSDRC_CR (AT91_DDRSDRC + 0x08) /* Configuration Register */
+#define AT91_DDRSDRC_CR 0x08 /* Configuration Register */
#define AT91_DDRSDRC_NC (3 << 0) /* Number of Column Bits */
#define AT91_DDRSDRC_NC_SDR8 (0 << 0)
#define AT91_DDRSDRC_NC_SDR9 (1 << 0)
#define AT91_DDRSDRC_DLL (1 << 7) /* Reset DLL */
#define AT91_DDRSDRC_DICDS (1 << 8) /* Output impedance control */
-#define AT91_DDRSDRC_T0PR (AT91_DDRSDRC + 0x0C) /* Timing 0 Register */
+#define AT91_DDRSDRC_T0PR 0x0C /* Timing 0 Register */
#define AT91_DDRSDRC_TRAS (0xf << 0) /* Active to Precharge delay */
#define AT91_DDRSDRC_TRCD (0xf << 4) /* Row to Column delay */
#define AT91_DDRSDRC_TWR (0xf << 8) /* Write recovery delay */
#define AT91_DDRSDRC_TWTR (1 << 24) /* Internal Write to Read delay */
#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */
-#define AT91_DDRSDRC_T1PR (AT91_DDRSDRC + 0x10) /* Timing 1 Register */
+#define AT91_DDRSDRC_T1PR 0x10 /* Timing 1 Register */
#define AT91_DDRSDRC_TRFC (0x1f << 0) /* Row Cycle Delay */
#define AT91_DDRSDRC_TXSNR (0xff << 8) /* Exit self-refresh to non-read */
#define AT91_DDRSDRC_TXSRD (0xff << 16) /* Exit self-refresh to read */
#define AT91_DDRSDRC_TXP (0xf << 24) /* Exit power-down delay */
-#define AT91_DDRSDRC_LPR (AT91_DDRSDRC + 0x18) /* Low Power Register */
+#define AT91_DDRSDRC_LPR 0x18 /* Low Power Register */
#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */
#define AT91_DDRSDRC_LPCB_DISABLE 0
#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1
#define AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES (1 << 12)
#define AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES (2 << 12)
-#define AT91_DDRSDRC_MDR (AT91_DDRSDRC + 0x1C) /* Memory Device Register */
+#define AT91_DDRSDRC_MDR 0x1C /* Memory Device Register */
#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
#define AT91_DDRSDRC_MD_SDR 0
#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
#define AT91_DDRSDRC_MD_DDR 2
#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
-#define AT91_DDRSDRC_DLLR (AT91_DDRSDRC + 0x20) /* DLL Information Register */
+#define AT91_DDRSDRC_DLLR 0x20 /* DLL Information Register */
#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */
#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */
#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */
#define AT91_DDRSDRC_SDVAL (0xff << 16) /* Slave Delay value */
#define AT91_DDRSDRC_SDCVAL (0xff << 24) /* Slave Delay Correction value */
+/* Register access macros */
+#define at91_ramc_read(num, reg) \
+ at91_sys_read(AT91_DDRSDRC##num + reg)
+#define at91_ramc_write(num, reg, value) \
+ at91_sys_write(AT91_DDRSDRC##num + reg, value)
+
#endif
* System Peripherals (offset from AT91_BASE_SYS)
*/
#define AT91_ECC (0xffffe800 - AT91_BASE_SYS)
-#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS)
+#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS)
+#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
--- /dev/null
+/*
+ * Header file for the Atmel DDR/SDR SDRAM Controller
+ *
+ * Copyright (C) 2010 Atmel Corporation
+ * Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT91SAM9_DDRSDR_H
+#define AT91SAM9_DDRSDR_H
+
+#define AT91_DDRSDRC_MR 0x00 /* Mode Register */
+#define AT91_DDRSDRC_MODE (0x7 << 0) /* Command Mode */
+#define AT91_DDRSDRC_MODE_NORMAL 0
+#define AT91_DDRSDRC_MODE_NOP 1
+#define AT91_DDRSDRC_MODE_PRECHARGE 2
+#define AT91_DDRSDRC_MODE_LMR 3
+#define AT91_DDRSDRC_MODE_REFRESH 4
+#define AT91_DDRSDRC_MODE_EXT_LMR 5
+#define AT91_DDRSDRC_MODE_DEEP 6
+
+#define AT91_DDRSDRC_RTR 0x04 /* Refresh Timer Register */
+#define AT91_DDRSDRC_COUNT (0xfff << 0) /* Refresh Timer Counter */
+
+#define AT91_DDRSDRC_CR 0x08 /* Configuration Register */
+#define AT91_DDRSDRC_NC (3 << 0) /* Number of Column Bits */
+#define AT91_DDRSDRC_NC_SDR8 (0 << 0)
+#define AT91_DDRSDRC_NC_SDR9 (1 << 0)
+#define AT91_DDRSDRC_NC_SDR10 (2 << 0)
+#define AT91_DDRSDRC_NC_SDR11 (3 << 0)
+#define AT91_DDRSDRC_NC_DDR9 (0 << 0)
+#define AT91_DDRSDRC_NC_DDR10 (1 << 0)
+#define AT91_DDRSDRC_NC_DDR11 (2 << 0)
+#define AT91_DDRSDRC_NC_DDR12 (3 << 0)
+#define AT91_DDRSDRC_NR (3 << 2) /* Number of Row Bits */
+#define AT91_DDRSDRC_NR_11 (0 << 2)
+#define AT91_DDRSDRC_NR_12 (1 << 2)
+#define AT91_DDRSDRC_NR_13 (2 << 2)
+#define AT91_DDRSDRC_NR_14 (3 << 2)
+#define AT91_DDRSDRC_CAS (7 << 4) /* CAS Latency */
+#define AT91_DDRSDRC_CAS_2 (2 << 4)
+#define AT91_DDRSDRC_CAS_3 (3 << 4)
+#define AT91_DDRSDRC_CAS_25 (6 << 4)
+#define AT91_DDRSDRC_RST_DLL (1 << 7) /* Reset DLL */
+#define AT91_DDRSDRC_DICDS (1 << 8) /* Output impedance control */
+#define AT91_DDRSDRC_DIS_DLL (1 << 9) /* Disable DLL */
+#define AT91_DDRSDRC_OCD (1 << 12) /* Off-Chip Driver */
+#define AT91_DDRSDRC_DQMS (1 << 16) /* Mask Data is Shared */
+#define AT91_DDRSDRC_ACTBST (1 << 18) /* Active Bank X to Burst Stop Read Access Bank Y */
+
+#define AT91_DDRSDRC_T0PR 0x0C /* Timing 0 Register */
+#define AT91_DDRSDRC_TRAS (0xf << 0) /* Active to Precharge delay */
+#define AT91_DDRSDRC_TRCD (0xf << 4) /* Row to Column delay */
+#define AT91_DDRSDRC_TWR (0xf << 8) /* Write recovery delay */
+#define AT91_DDRSDRC_TRC (0xf << 12) /* Row cycle delay */
+#define AT91_DDRSDRC_TRP (0xf << 16) /* Row precharge delay */
+#define AT91_DDRSDRC_TRRD (0xf << 20) /* Active BankA to BankB */
+#define AT91_DDRSDRC_TWTR (0x7 << 24) /* Internal Write to Read delay */
+#define AT91_DDRSDRC_RED_WRRD (0x1 << 27) /* Reduce Write to Read Delay */
+#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */
+
+#define AT91_DDRSDRC_T1PR 0x10 /* Timing 1 Register */
+#define AT91_DDRSDRC_TRFC (0x1f << 0) /* Row Cycle Delay */
+#define AT91_DDRSDRC_TXSNR (0xff << 8) /* Exit self-refresh to non-read */
+#define AT91_DDRSDRC_TXSRD (0xff << 16) /* Exit self-refresh to read */
+#define AT91_DDRSDRC_TXP (0xf << 24) /* Exit power-down delay */
+
+#define AT91_DDRSDRC_T2PR 0x14 /* Timing 2 Register */
+#define AT91_DDRSDRC_TXARD (0xf << 0) /* Exit active power down delay to read command in mode "Fast Exit" */
+#define AT91_DDRSDRC_TXARDS (0xf << 4) /* Exit active power down delay to read command in mode "Slow Exit" */
+#define AT91_DDRSDRC_TRPA (0xf << 8) /* Row Precharge All delay */
+#define AT91_DDRSDRC_TRTP (0x7 << 12) /* Read to Precharge delay */
+
+#define AT91_DDRSDRC_LPR 0x1C /* Low Power Register */
+#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */
+#define AT91_DDRSDRC_LPCB_DISABLE 0
+#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1
+#define AT91_DDRSDRC_LPCB_POWER_DOWN 2
+#define AT91_DDRSDRC_LPCB_DEEP_POWER_DOWN 3
+#define AT91_DDRSDRC_CLKFR (1 << 2) /* Clock Frozen */
+#define AT91_DDRSDRC_PASR (7 << 4) /* Partial Array Self Refresh */
+#define AT91_DDRSDRC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
+#define AT91_DDRSDRC_DS (3 << 10) /* Drive Strength */
+#define AT91_DDRSDRC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */
+#define AT91_DDRSDRC_TIMEOUT_0_CLK_CYCLES (0 << 12)
+#define AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES (1 << 12)
+#define AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES (2 << 12)
+#define AT91_DDRSDRC_APDE (1 << 16) /* Active power down exit time */
+#define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */
+
+#define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */
+#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
+#define AT91_DDRSDRC_MD_SDR 0
+#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
+#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
+#define AT91_DDRSDRC_MD_DDR2 6
+#define AT91_DDRSDRC_DBW (1 << 4) /* Data Bus Width */
+#define AT91_DDRSDRC_DBW_32BITS (0 << 4)
+#define AT91_DDRSDRC_DBW_16BITS (1 << 4)
+
+#define AT91_DDRSDRC_DLL 0x24 /* DLL Information Register */
+#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */
+#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */
+#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */
+#define AT91_DDRSDRC_MDVAL (0xff << 8) /* Master Delay value */
+
+#define AT91_DDRSDRC_HS 0x2C /* High Speed Register */
+#define AT91_DDRSDRC_DIS_ATCP_RD (1 << 2) /* Anticip read access is disabled */
+
+#define AT91_DDRSDRC_DELAY(n) (0x30 + (0x4 * (n))) /* Delay I/O Register n */
+
+#define AT91_DDRSDRC_WPMR 0xE4 /* Write Protect Mode Register */
+#define AT91_DDRSDRC_WP (1 << 0) /* Write protect enable */
+#define AT91_DDRSDRC_WPKEY (0xffffff << 8) /* Write protect key */
+#define AT91_DDRSDRC_KEY (0x444452 << 8) /* Write protect key = "DDR" */
+
+#define AT91_DDRSDRC_WPSR 0xE8 /* Write Protect Status Register */
+#define AT91_DDRSDRC_WPVS (1 << 0) /* Write protect violation status */
+#define AT91_DDRSDRC_WPVSRC (0xffff << 8) /* Write protect violation source */
+
+/* Register access macros */
+#define at91_ramc_read(num, reg) \
+ at91_sys_read(AT91_DDRSDRC##num + reg)
+#define at91_ramc_write(num, reg, value) \
+ at91_sys_write(AT91_DDRSDRC##num + reg, value)
+
+#endif
#define AT91SAM9_SDRAMC_H
/* SDRAM Controller (SDRAMC) registers */
-#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM Controller Mode Register */
+#define AT91_SDRAMC_MR 0x00 /* SDRAM Controller Mode Register */
#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
#define AT91_SDRAMC_MODE_NORMAL 0
#define AT91_SDRAMC_MODE_NOP 1
#define AT91_SDRAMC_MODE_EXT_LMR 5
#define AT91_SDRAMC_MODE_DEEP 6
-#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM Controller Refresh Timer Register */
+#define AT91_SDRAMC_TR 0x04 /* SDRAM Controller Refresh Timer Register */
#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */
-#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM Controller Configuration Register */
+#define AT91_SDRAMC_CR 0x08 /* SDRAM Controller Configuration Register */
#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
#define AT91_SDRAMC_NC_8 (0 << 0)
#define AT91_SDRAMC_NC_9 (1 << 0)
#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */
#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */
-#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM Controller Low Power Register */
+#define AT91_SDRAMC_LPR 0x10 /* SDRAM Controller Low Power Register */
#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */
#define AT91_SDRAMC_LPCB_DISABLE 0
#define AT91_SDRAMC_LPCB_SELF_REFRESH 1
#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12)
#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12)
-#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM Controller Interrupt Enable Register */
-#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM Controller Interrupt Disable Register */
-#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM Controller Interrupt Mask Register */
-#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM Controller Interrupt Status Register */
+#define AT91_SDRAMC_IER 0x14 /* SDRAM Controller Interrupt Enable Register */
+#define AT91_SDRAMC_IDR 0x18 /* SDRAM Controller Interrupt Disable Register */
+#define AT91_SDRAMC_IMR 0x1C /* SDRAM Controller Interrupt Mask Register */
+#define AT91_SDRAMC_ISR 0x20 /* SDRAM Controller Interrupt Status Register */
#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */
-#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory Device Register */
+#define AT91_SDRAMC_MDR 0x24 /* SDRAM Memory Device Register */
#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */
#define AT91_SDRAMC_MD_SDRAM 0
#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
+/* Register access macros */
+#define at91_ramc_read(num, reg) \
+ at91_sys_read(AT91_SDRAMC##num + reg)
+#define at91_ramc_write(num, reg, value) \
+ at91_sys_write(AT91_SDRAMC##num + reg, value)
#endif
*/
#define AT91_DMA (0xffffe600 - AT91_BASE_SYS)
#define AT91_ECC (0xffffe800 - AT91_BASE_SYS)
-#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS)
+#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
{
u32 saved_lpr, lpr;
- saved_lpr = at91_sys_read(AT91_DDRSDRC_LPR);
+ saved_lpr = at91_ramc_read(0, AT91_DDRSDRC_LPR);
lpr = saved_lpr & ~AT91_DDRSDRC_LPCB;
- at91_sys_write(AT91_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH);
+ at91_ramc_write(0, AT91_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH);
return saved_lpr;
}
-#define sdram_selfrefresh_disable(saved_lpr) at91_sys_write(AT91_DDRSDRC_LPR, saved_lpr)
+#define sdram_selfrefresh_disable(saved_lpr) at91_ramc_write(0, AT91_DDRSDRC_LPR, saved_lpr)
+
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
+#include <mach/at91sam9_ddrsdr.h>
+
+/* We manage both DDRAM/SDRAM controllers, we need more than one value to
+ * remember.
+ */
+static u32 saved_lpr1;
+
+static inline u32 sdram_selfrefresh_enable(void)
+{
+ /* Those tow values allow us to delay self-refresh activation
+ * to the maximum. */
+ u32 lpr0, lpr1;
+ u32 saved_lpr0;
+
+ saved_lpr1 = at91_ramc_read(1, AT91_DDRSDRC_LPR);
+ lpr1 = saved_lpr1 & ~AT91_DDRSDRC_LPCB;
+ lpr1 |= AT91_DDRSDRC_LPCB_SELF_REFRESH;
+
+ saved_lpr0 = at91_ramc_read(0, AT91_DDRSDRC_LPR);
+ lpr0 = saved_lpr0 & ~AT91_DDRSDRC_LPCB;
+ lpr0 |= AT91_DDRSDRC_LPCB_SELF_REFRESH;
+
+ /* self-refresh mode now */
+ at91_ramc_write(0, AT91_DDRSDRC_LPR, lpr0);
+ at91_ramc_write(1, AT91_DDRSDRC_LPR, lpr1);
+
+ return saved_lpr0;
+}
+
+#define sdram_selfrefresh_disable(saved_lpr0) \
+ do { \
+ at91_ramc_write(0, AT91_DDRSDRC_LPR, saved_lpr0); \
+ at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1); \
+ } while (0)
#else
#include <mach/at91sam9_sdramc.h>
* FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;
* handle those cases both here and in the Suspend-To-RAM support.
*/
-#define AT91_SDRAMC AT91_SDRAMC0
#warning Assuming EB1 SDRAM controller is *NOT* used
#endif
{
u32 saved_lpr, lpr;
- saved_lpr = at91_sys_read(AT91_SDRAMC_LPR);
+ saved_lpr = at91_ramc_read(0, AT91_SDRAMC_LPR);
lpr = saved_lpr & ~AT91_SDRAMC_LPCB;
- at91_sys_write(AT91_SDRAMC_LPR, lpr | AT91_SDRAMC_LPCB_SELF_REFRESH);
+ at91_ramc_write(0, AT91_SDRAMC_LPR, lpr | AT91_SDRAMC_LPCB_SELF_REFRESH);
return saved_lpr;
}
-#define sdram_selfrefresh_disable(saved_lpr) at91_sys_write(AT91_SDRAMC_LPR, saved_lpr)
+#define sdram_selfrefresh_disable(saved_lpr) at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr)
#endif
#include <mach/hardware.h>
#include <mach/at91_pmc.h>
-#ifdef CONFIG_ARCH_AT91RM9200
+#if defined(CONFIG_ARCH_AT91RM9200)
#include <mach/at91rm9200_mc.h>
#elif defined(CONFIG_ARCH_AT91CAP9)
#include <mach/at91cap9_ddrsdr.h>
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
+#include <mach/at91sam9_ddrsdr.h>
#else
#include <mach/at91sam9_sdramc.h>
#endif
* FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;
* handle those cases both here and in the Suspend-To-RAM support.
*/
-#define AT91_SDRAMC AT91_SDRAMC0
#warning Assuming EB1 SDRAM controller is *NOT* used
#endif
/*
* Register usage:
* R1 = Base address of AT91_PMC
- * R2 = Base address of AT91_SDRAMC (or AT91_SYS on AT91RM9200)
+ * R2 = Base address of RAM Controller (SDRAM, DDRSDR, or AT91_SYS)
* R3 = temporary register
* R4 = temporary register
+ * R5 = Base address of second RAM Controller or 0 if not present
*/
ldr r1, .at91_va_base_pmc
ldr r2, .at91_va_base_sdramc
+ ldr r5, .at91_va_base_ramc1
/* Drain write buffer */
mcr p15, 0, r0, c7, c10, 4
/* Put SDRAM in self-refresh mode */
mov r3, #1
str r3, [r2, #AT91_SDRAMC_SRR]
-#elif defined(CONFIG_ARCH_AT91CAP9)
- /* Enable SDRAM self-refresh mode */
- ldr r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC]
- str r3, .saved_sam9_lpr
+#elif defined(CONFIG_ARCH_AT91CAP9) \
+ || defined(CONFIG_ARCH_AT91SAM9G45)
- mov r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH
- str r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC]
+ /* prepare for DDRAM self-refresh mode */
+ ldr r3, [r2, #AT91_DDRSDRC_LPR]
+ str r3, .saved_sam9_lpr
+ bic r3, #AT91_DDRSDRC_LPCB
+ orr r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+
+ /* figure out if we use the second ram controller */
+ cmp r5, #0
+ ldrne r4, [r5, #AT91_DDRSDRC_LPR]
+ strne r4, .saved_sam9_lpr1
+ bicne r4, #AT91_DDRSDRC_LPCB
+ orrne r4, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+
+ /* Enable DDRAM self-refresh mode */
+ str r3, [r2, #AT91_DDRSDRC_LPR]
+ strne r4, [r5, #AT91_DDRSDRC_LPR]
#else
/* Enable SDRAM self-refresh mode */
- ldr r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC]
+ ldr r3, [r2, #AT91_SDRAMC_LPR]
str r3, .saved_sam9_lpr
- mov r3, #AT91_SDRAMC_LPCB_SELF_REFRESH
- str r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC]
+ bic r3, #AT91_SDRAMC_LPCB
+ orr r3, #AT91_SDRAMC_LPCB_SELF_REFRESH
+ str r3, [r2, #AT91_SDRAMC_LPR]
#endif
/* Save Master clock setting */
#ifdef CONFIG_ARCH_AT91RM9200
/* Do nothing - self-refresh is automatically disabled. */
-#elif defined(CONFIG_ARCH_AT91CAP9)
- /* Restore LPR on AT91CAP9 */
+#elif defined(CONFIG_ARCH_AT91CAP9) \
+ || defined(CONFIG_ARCH_AT91SAM9G45)
+ /* Restore LPR on AT91 with DDRAM */
ldr r3, .saved_sam9_lpr
- str r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC]
+ str r3, [r2, #AT91_DDRSDRC_LPR]
+
+ /* if we use the second ram controller */
+ cmp r5, #0
+ ldrne r4, .saved_sam9_lpr1
+ strne r4, [r5, #AT91_DDRSDRC_LPR]
+
#else
- /* Restore LPR on AT91SAM9 */
+ /* Restore LPR on AT91 with SDRAM */
ldr r3, .saved_sam9_lpr
- str r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC]
+ str r3, [r2, #AT91_SDRAMC_LPR]
#endif
/* Restore registers, and return */
.saved_sam9_lpr:
.word 0
+.saved_sam9_lpr1:
+ .word 0
+
.at91_va_base_pmc:
.word AT91_VA_BASE_SYS + AT91_PMC
#ifdef CONFIG_ARCH_AT91RM9200
.at91_va_base_sdramc:
.word AT91_VA_BASE_SYS
-#elif defined(CONFIG_ARCH_AT91CAP9)
+#elif defined(CONFIG_ARCH_AT91CAP9) \
+ || defined(CONFIG_ARCH_AT91SAM9G45)
.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_DDRSDRC
+ .word AT91_VA_BASE_SYS + AT91_DDRSDRC0
#else
.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_SDRAMC
+ .word AT91_VA_BASE_SYS + AT91_SDRAMC0
+#endif
+
+.at91_va_base_ramc1:
+#if defined(CONFIG_ARCH_AT91SAM9G45)
+ .word AT91_VA_BASE_SYS + AT91_DDRSDRC1
+#else
+ .word 0
#endif
ENTRY(at91_slow_clock_sz)
projects / linux-platform-drivers-x86.git / commitdiff