#define BE_FLAGS_PHY_MISCONFIGURED BIT(10)
#define BE_FLAGS_ERR_DETECTION_SCHEDULED BIT(11)
#define BE_FLAGS_OS2BMC BIT(12)
+#define BE_FLAGS_TRY_RECOVERY BIT(13)
#define BE_UC_PMAC_COUNT 30
#define BE_VF_UC_PMAC_COUNT 2
#define MAX_ERR_RECOVERY_RETRY_COUNT 3
#define ERR_DETECTION_DELAY 1000
-#define ERR_RECOVERY_RETRY_DELAY 30000
/* Ethtool set_dump flags */
#define LANCER_INITIATE_FW_DUMP 0x1
unsigned char mac[ETH_ALEN];
};
+#define BE_SEC 1000 /* in msec */
+#define BE_MIN (60 * BE_SEC) /* in msec */
+#define BE_HOUR (60 * BE_MIN) /* in msec */
+
+#define ERR_RECOVERY_MAX_RETRY_COUNT 3
+#define ERR_RECOVERY_DETECTION_DELAY BE_SEC
+#define ERR_RECOVERY_RETRY_DELAY (30 * BE_SEC)
+
+/* UE-detection-duration in BEx/Skyhawk:
+ * All PFs must wait for this duration after they detect UE before reading
+ * SLIPORT_SEMAPHORE register. At the end of this duration, the Firmware
+ * guarantees that the SLIPORT_SEMAPHORE register is updated to indicate
+ * if the UE is recoverable.
+ */
+#define ERR_RECOVERY_UE_DETECT_DURATION BE_SEC
+
+/* Initial idle time (in msec) to elapse after driver load,
+ * before UE recovery is allowed.
+ */
+#define ERR_IDLE_HR 24
+#define ERR_RECOVERY_IDLE_TIME (ERR_IDLE_HR * BE_HOUR)
+
+/* Time interval (in msec) after which UE recovery can be repeated */
+#define ERR_INTERVAL_HR 72
+#define ERR_RECOVERY_INTERVAL (ERR_INTERVAL_HR * BE_HOUR)
+
+/* BEx/SH UE recovery state machine */
+enum {
+ ERR_RECOVERY_ST_NONE = 0, /* No Recovery */
+ ERR_RECOVERY_ST_DETECT = 1, /* UE detection duration */
+ ERR_RECOVERY_ST_RESET = 2, /* Reset Phase (PF0 only) */
+ ERR_RECOVERY_ST_PRE_POLL = 3, /* Pre-Poll Phase (all PFs) */
+ ERR_RECOVERY_ST_REINIT = 4 /* Re-initialize Phase */
+};
+
+struct be_error_recovery {
+ /* Lancer error recovery variables */
+ u8 recovery_retries;
+
+ /* BEx/Skyhawk error recovery variables */
+ u8 recovery_state;
+ u16 ue_to_reset_time; /* Time after UE, to soft reset
+ * the chip - PF0 only
+ */
+ u16 ue_to_poll_time; /* Time after UE, to Restart Polling
+ * of SLIPORT_SEMAPHORE reg
+ */
+ u16 last_err_code;
+ bool recovery_supported;
+ unsigned long probe_time;
+ unsigned long last_recovery_time;
+
+ /* Common to both Lancer & BEx/SH error recovery */
+ u32 resched_delay;
+ struct delayed_work err_detection_work;
+};
+
+/* Ethtool priv_flags */
+#define BE_DISABLE_TPE_RECOVERY 0x1
+
struct be_adapter {
struct pci_dev *pdev;
struct net_device *netdev;
struct delayed_work work;
u16 work_counter;
- struct delayed_work be_err_detection_work;
u8 recovery_retries;
u8 err_flags;
bool pcicfg_mapped; /* pcicfg obtained via pci_iomap() */
u32 fat_dump_len;
u16 serial_num[CNTL_SERIAL_NUM_WORDS];
u8 phy_state; /* state of sfp optics (functional, faulted, etc.,) */
+ u32 priv_flags; /* ethtool get/set_priv_flags() */
+ struct be_error_recovery error_recovery;
};
/* Used for defered FW config cmds. Add fields to this struct as reqd */
return skb->protocol == htons(ETH_P_IP) && ip_hdr(skb)->version == 4;
}
+#define be_error_recovering(adapter) \
+ (adapter->flags & BE_FLAGS_TRY_RECOVERY)
+
#define BE_ERROR_EEH 1
#define BE_ERROR_UE BIT(1)
#define BE_ERROR_FW BIT(2)
module_param(rx_frag_size, ushort, S_IRUGO);
MODULE_PARM_DESC(rx_frag_size, "Size of a fragment that holds rcvd data.");
+/* Per-module error detection/recovery workq shared across all functions.
+ * Each function schedules its own work request on this shared workq.
+ */
+struct workqueue_struct *be_err_recovery_workq;
+
static const struct pci_device_id be_dev_ids[] = {
{ PCI_DEVICE(BE_VENDOR_ID, BE_DEVICE_ID1) },
{ PCI_DEVICE(BE_VENDOR_ID, BE_DEVICE_ID2) },
*/
if (ue_lo || ue_hi) {
- dev_err(dev,
- "Unrecoverable Error detected in the adapter");
- dev_err(dev, "Please reboot server to recover");
+ dev_err(dev, "Error detected in the adapter");
if (skyhawk_chip(adapter))
be_set_error(adapter, BE_ERROR_UE);
static void be_cancel_err_detection(struct be_adapter *adapter)
{
+ struct be_error_recovery *err_rec = &adapter->error_recovery;
+
+ if (!be_err_recovery_workq)
+ return;
+
if (adapter->flags & BE_FLAGS_ERR_DETECTION_SCHEDULED) {
- cancel_delayed_work_sync(&adapter->be_err_detection_work);
+ cancel_delayed_work_sync(&err_rec->err_detection_work);
adapter->flags &= ~BE_FLAGS_ERR_DETECTION_SCHEDULED;
}
}
adapter->flags |= BE_FLAGS_WORKER_SCHEDULED;
}
+static void be_destroy_err_recovery_workq(void)
+{
+ if (!be_err_recovery_workq)
+ return;
+
+ flush_workqueue(be_err_recovery_workq);
+ destroy_workqueue(be_err_recovery_workq);
+ be_err_recovery_workq = NULL;
+}
+
static void be_schedule_err_detection(struct be_adapter *adapter, u32 delay)
{
- schedule_delayed_work(&adapter->be_err_detection_work,
- msecs_to_jiffies(delay));
+ struct be_error_recovery *err_rec = &adapter->error_recovery;
+
+ if (!be_err_recovery_workq)
+ return;
+
+ queue_delayed_work(be_err_recovery_workq, &err_rec->err_detection_work,
+ msecs_to_jiffies(delay));
adapter->flags |= BE_FLAGS_ERR_DETECTION_SCHEDULED;
}
return fw_major;
}
-/* If any VFs are already enabled don't FLR the PF */
+/* If it is error recovery, FLR the PF
+ * Else if any VFs are already enabled don't FLR the PF
+ */
static bool be_reset_required(struct be_adapter *adapter)
{
- return pci_num_vf(adapter->pdev) ? false : true;
+ if (be_error_recovering(adapter))
+ return true;
+ else
+ return pci_num_vf(adapter->pdev) == 0;
}
/* Wait for the FW to be ready and perform the required initialization */
if (status)
return status;
+ /* FW is now ready; clear errors to allow cmds/doorbell */
+ be_clear_error(adapter, BE_CLEAR_ALL);
+
if (be_reset_required(adapter)) {
status = be_cmd_reset_function(adapter);
if (status)
/* Wait for interrupts to quiesce after an FLR */
msleep(100);
-
- /* We can clear all errors when function reset succeeds */
- be_clear_error(adapter, BE_CLEAR_ALL);
}
/* Tell FW we're ready to fire cmds */
if (!status && be_pause_supported(adapter))
adapter->phy.fc_autoneg = 1;
+ if (be_physfn(adapter) && !lancer_chip(adapter))
+ be_cmd_set_features(adapter);
+
be_schedule_worker(adapter);
adapter->flags |= BE_FLAGS_SETUP_DONE;
return 0;
return 0;
}
+static void be_soft_reset(struct be_adapter *adapter)
+{
+ u32 val;
+
+ dev_info(&adapter->pdev->dev, "Initiating chip soft reset\n");
+ val = ioread32(adapter->pcicfg + SLIPORT_SOFTRESET_OFFSET);
+ val |= SLIPORT_SOFTRESET_SR_MASK;
+ iowrite32(val, adapter->pcicfg + SLIPORT_SOFTRESET_OFFSET);
+}
+
+static bool be_err_is_recoverable(struct be_adapter *adapter)
+{
+ struct be_error_recovery *err_rec = &adapter->error_recovery;
+ unsigned long initial_idle_time =
+ msecs_to_jiffies(ERR_RECOVERY_IDLE_TIME);
+ unsigned long recovery_interval =
+ msecs_to_jiffies(ERR_RECOVERY_INTERVAL);
+ u16 ue_err_code;
+ u32 val;
+
+ val = be_POST_stage_get(adapter);
+ if ((val & POST_STAGE_RECOVERABLE_ERR) != POST_STAGE_RECOVERABLE_ERR)
+ return false;
+ ue_err_code = val & POST_ERR_RECOVERY_CODE_MASK;
+ if (ue_err_code == 0)
+ return false;
+
+ dev_err(&adapter->pdev->dev, "Recoverable HW error code: 0x%x\n",
+ ue_err_code);
+
+ if (jiffies - err_rec->probe_time <= initial_idle_time) {
+ dev_err(&adapter->pdev->dev,
+ "Cannot recover within %lu sec from driver load\n",
+ jiffies_to_msecs(initial_idle_time) / MSEC_PER_SEC);
+ return false;
+ }
+
+ if (err_rec->last_recovery_time &&
+ (jiffies - err_rec->last_recovery_time <= recovery_interval)) {
+ dev_err(&adapter->pdev->dev,
+ "Cannot recover within %lu sec from last recovery\n",
+ jiffies_to_msecs(recovery_interval) / MSEC_PER_SEC);
+ return false;
+ }
+
+ if (ue_err_code == err_rec->last_err_code) {
+ dev_err(&adapter->pdev->dev,
+ "Cannot recover from a consecutive TPE error\n");
+ return false;
+ }
+
+ err_rec->last_recovery_time = jiffies;
+ err_rec->last_err_code = ue_err_code;
+ return true;
+}
+
+static int be_tpe_recover(struct be_adapter *adapter)
+{
+ struct be_error_recovery *err_rec = &adapter->error_recovery;
+ int status = -EAGAIN;
+ u32 val;
+
+ switch (err_rec->recovery_state) {
+ case ERR_RECOVERY_ST_NONE:
+ err_rec->recovery_state = ERR_RECOVERY_ST_DETECT;
+ err_rec->resched_delay = ERR_RECOVERY_UE_DETECT_DURATION;
+ break;
+
+ case ERR_RECOVERY_ST_DETECT:
+ val = be_POST_stage_get(adapter);
+ if ((val & POST_STAGE_RECOVERABLE_ERR) !=
+ POST_STAGE_RECOVERABLE_ERR) {
+ dev_err(&adapter->pdev->dev,
+ "Unrecoverable HW error detected: 0x%x\n", val);
+ status = -EINVAL;
+ err_rec->resched_delay = 0;
+ break;
+ }
+
+ dev_err(&adapter->pdev->dev, "Recoverable HW error detected\n");
+
+ /* Only PF0 initiates Chip Soft Reset. But PF0 must wait UE2SR
+ * milliseconds before it checks for final error status in
+ * SLIPORT_SEMAPHORE to determine if recovery criteria is met.
+ * If it does, then PF0 initiates a Soft Reset.
+ */
+ if (adapter->pf_num == 0) {
+ err_rec->recovery_state = ERR_RECOVERY_ST_RESET;
+ err_rec->resched_delay = err_rec->ue_to_reset_time -
+ ERR_RECOVERY_UE_DETECT_DURATION;
+ break;
+ }
+
+ err_rec->recovery_state = ERR_RECOVERY_ST_PRE_POLL;
+ err_rec->resched_delay = err_rec->ue_to_poll_time -
+ ERR_RECOVERY_UE_DETECT_DURATION;
+ break;
+
+ case ERR_RECOVERY_ST_RESET:
+ if (!be_err_is_recoverable(adapter)) {
+ dev_err(&adapter->pdev->dev,
+ "Failed to meet recovery criteria\n");
+ status = -EIO;
+ err_rec->resched_delay = 0;
+ break;
+ }
+ be_soft_reset(adapter);
+ err_rec->recovery_state = ERR_RECOVERY_ST_PRE_POLL;
+ err_rec->resched_delay = err_rec->ue_to_poll_time -
+ err_rec->ue_to_reset_time;
+ break;
+
+ case ERR_RECOVERY_ST_PRE_POLL:
+ err_rec->recovery_state = ERR_RECOVERY_ST_REINIT;
+ err_rec->resched_delay = 0;
+ status = 0; /* done */
+ break;
+
+ default:
+ status = -EINVAL;
+ err_rec->resched_delay = 0;
+ break;
+ }
+
+ return status;
+}
+
static int be_err_recover(struct be_adapter *adapter)
{
int status;
- /* Error recovery is supported only Lancer as of now */
- if (!lancer_chip(adapter))
- return -EIO;
+ if (!lancer_chip(adapter)) {
+ if (!adapter->error_recovery.recovery_supported ||
+ adapter->priv_flags & BE_DISABLE_TPE_RECOVERY)
+ return -EIO;
+ status = be_tpe_recover(adapter);
+ if (status)
+ goto err;
+ }
/* Wait for adapter to reach quiescent state before
* destroying queues
if (status)
goto err;
+ adapter->flags |= BE_FLAGS_TRY_RECOVERY;
+
be_cleanup(adapter);
status = be_resume(adapter);
if (status)
goto err;
- return 0;
+ adapter->flags &= ~BE_FLAGS_TRY_RECOVERY;
+
err:
return status;
}
static void be_err_detection_task(struct work_struct *work)
{
+ struct be_error_recovery *err_rec =
+ container_of(work, struct be_error_recovery,
+ err_detection_work.work);
struct be_adapter *adapter =
- container_of(work, struct be_adapter,
- be_err_detection_work.work);
+ container_of(err_rec, struct be_adapter,
+ error_recovery);
+ u32 resched_delay = ERR_RECOVERY_DETECTION_DELAY;
struct device *dev = &adapter->pdev->dev;
int recovery_status;
- int delay = ERR_DETECTION_DELAY;
be_detect_error(adapter);
-
- if (be_check_error(adapter, BE_ERROR_HW))
- recovery_status = be_err_recover(adapter);
- else
+ if (!be_check_error(adapter, BE_ERROR_HW))
goto reschedule_task;
+ recovery_status = be_err_recover(adapter);
if (!recovery_status) {
- adapter->recovery_retries = 0;
+ err_rec->recovery_retries = 0;
+ err_rec->recovery_state = ERR_RECOVERY_ST_NONE;
dev_info(dev, "Adapter recovery successful\n");
goto reschedule_task;
- } else if (be_virtfn(adapter)) {
+ } else if (!lancer_chip(adapter) && err_rec->resched_delay) {
+ /* BEx/SH recovery state machine */
+ if (adapter->pf_num == 0 &&
+ err_rec->recovery_state > ERR_RECOVERY_ST_DETECT)
+ dev_err(&adapter->pdev->dev,
+ "Adapter recovery in progress\n");
+ resched_delay = err_rec->resched_delay;
+ goto reschedule_task;
+ } else if (lancer_chip(adapter) && be_virtfn(adapter)) {
/* For VFs, check if PF have allocated resources
* every second.
*/
dev_err(dev, "Re-trying adapter recovery\n");
goto reschedule_task;
- } else if (adapter->recovery_retries++ <
- MAX_ERR_RECOVERY_RETRY_COUNT) {
+ } else if (lancer_chip(adapter) && err_rec->recovery_retries++ <
+ ERR_RECOVERY_MAX_RETRY_COUNT) {
/* In case of another error during recovery, it takes 30 sec
* for adapter to come out of error. Retry error recovery after
* this time interval.
*/
dev_err(&adapter->pdev->dev, "Re-trying adapter recovery\n");
- delay = ERR_RECOVERY_RETRY_DELAY;
+ resched_delay = ERR_RECOVERY_RETRY_DELAY;
goto reschedule_task;
} else {
dev_err(dev, "Adapter recovery failed\n");
+ dev_err(dev, "Please reboot server to recover\n");
}
return;
+
reschedule_task:
- be_schedule_err_detection(adapter, delay);
+ be_schedule_err_detection(adapter, resched_delay);
}
static void be_log_sfp_info(struct be_adapter *adapter)
pci_save_state(adapter->pdev);
INIT_DELAYED_WORK(&adapter->work, be_worker);
- INIT_DELAYED_WORK(&adapter->be_err_detection_work,
+
+ adapter->error_recovery.recovery_state = ERR_RECOVERY_ST_NONE;
+ adapter->error_recovery.resched_delay = 0;
+ INIT_DELAYED_WORK(&adapter->error_recovery.err_detection_work,
be_err_detection_task);
adapter->rx_fc = true;
be_roce_dev_add(adapter);
be_schedule_err_detection(adapter, ERR_DETECTION_DELAY);
+ adapter->error_recovery.probe_time = jiffies;
/* On Die temperature not supported for VF. */
if (be_physfn(adapter) && IS_ENABLED(CONFIG_BE2NET_HWMON)) {
static int __init be_init_module(void)
{
+ int status;
+
if (rx_frag_size != 8192 && rx_frag_size != 4096 &&
rx_frag_size != 2048) {
printk(KERN_WARNING DRV_NAME
return -1;
}
- return pci_register_driver(&be_driver);
+ be_err_recovery_workq =
+ create_singlethread_workqueue("be_err_recover");
+ if (!be_err_recovery_workq)
+ pr_warn(DRV_NAME "Could not create error recovery workqueue\n");
+
+ status = pci_register_driver(&be_driver);
+ if (status) {
+ destroy_workqueue(be_wq);
+ be_destroy_err_recovery_workq();
+ }
+ return status;
}
module_init(be_init_module);
{
pci_unregister_driver(&be_driver);
+ be_destroy_err_recovery_workq();
+
if (be_wq)
destroy_workqueue(be_wq);
}
projects / linux-platform-drivers-x86.git / commitdiff