drivers/net/phy: add driver for Microchip LAN867x 10BASE-T1S PHY

This patch adds support for the Microchip LAN867x 10BASE-T1S family
(LAN8670/1/2). The driver supports P2MP with PLCA.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index bcfba077b80e1358444200539607d59b261ca6ca..2f3ddc446cbb811ae703da5cfb8763adf4fe29b3 100644 (file)
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -244,6 +244,11 @@ config MICREL_PHY
        help
          Supports the KSZ9021, VSC8201, KS8001 PHYs.
 
+config MICROCHIP_T1S_PHY
+       tristate "Microchip 10BASE-T1S Ethernet PHY"
+       help
+         Currently supports the LAN8670, LAN8671, LAN8672
+
 config MICROCHIP_PHY
        tristate "Microchip PHYs"
        help

diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index ae11bf20b46ee3f798d3df66e2b1aaedb803e968..f289ab16a1dab39e6670d7289f4a994ce8b2e8bc 100644 (file)
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -74,6 +74,7 @@ obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
 obj-$(CONFIG_MICREL_PHY)       += micrel.o
 obj-$(CONFIG_MICROCHIP_PHY)    += microchip.o
 obj-$(CONFIG_MICROCHIP_T1_PHY) += microchip_t1.o
+obj-$(CONFIG_MICROCHIP_T1S_PHY) += microchip_t1s.o
 obj-$(CONFIG_MICROSEMI_PHY)    += mscc/
 obj-$(CONFIG_MOTORCOMM_PHY)    += motorcomm.o
 obj-$(CONFIG_NATIONAL_PHY)     += national.o

diff --git a/drivers/net/phy/microchip_t1s.c b/drivers/net/phy/microchip_t1s.c
new file mode 100644 (file)
index 0000000..094967b
--- /dev/null
+++ b/drivers/net/phy/microchip_t1s.c
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for Microchip 10BASE-T1S LAN867X PHY
+ *
+ * Support: Microchip Phys:
+ *  lan8670, lan8671, lan8672
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+
+#define PHY_ID_LAN867X 0x0007C160
+
+#define LAN867X_REG_IRQ_1_CTL 0x001C
+#define LAN867X_REG_IRQ_2_CTL 0x001D
+
+/* The arrays below are pulled from the following table from AN1699
+ * Access MMD Address Value Mask
+ * RMW 0x1F 0x00D0 0x0002 0x0E03
+ * RMW 0x1F 0x00D1 0x0000 0x0300
+ * RMW 0x1F 0x0084 0x3380 0xFFC0
+ * RMW 0x1F 0x0085 0x0006 0x000F
+ * RMW 0x1F 0x008A 0xC000 0xF800
+ * RMW 0x1F 0x0087 0x801C 0x801C
+ * RMW 0x1F 0x0088 0x033F 0x1FFF
+ * W   0x1F 0x008B 0x0404 ------
+ * RMW 0x1F 0x0080 0x0600 0x0600
+ * RMW 0x1F 0x00F1 0x2400 0x7F00
+ * RMW 0x1F 0x0096 0x2000 0x2000
+ * W   0x1F 0x0099 0x7F80 ------
+ */
+
+static const int lan867x_fixup_registers[12] = {
+       0x00D0, 0x00D1, 0x0084, 0x0085,
+       0x008A, 0x0087, 0x0088, 0x008B,
+       0x0080, 0x00F1, 0x0096, 0x0099,
+};
+
+static const int lan867x_fixup_values[12] = {
+       0x0002, 0x0000, 0x3380, 0x0006,
+       0xC000, 0x801C, 0x033F, 0x0404,
+       0x0600, 0x2400, 0x2000, 0x7F80,
+};
+
+static const int lan867x_fixup_masks[12] = {
+       0x0E03, 0x0300, 0xFFC0, 0x000F,
+       0xF800, 0x801C, 0x1FFF, 0xFFFF,
+       0x0600, 0x7F00, 0x2000, 0xFFFF,
+};
+
+static int lan867x_config_init(struct phy_device *phydev)
+{
+       /* HW quirk: Microchip states in the application note (AN1699) for the phy
+        * that a set of read-modify-write (rmw) operations has to be performed
+        * on a set of seemingly magic registers.
+        * The result of these operations is just described as 'optimal performance'
+        * Microchip gives no explanation as to what these mmd regs do,
+        * in fact they are marked as reserved in the datasheet.
+        * It is unclear if phy_modify_mmd would be safe to use or if a write
+        * really has to happen to each register.
+        * In order to exactly conform to what is stated in the AN phy_write_mmd is
+        * used, which might then write the same value back as read + modified.
+        */
+
+       int reg_value;
+       int err;
+       int reg;
+
+       /* Read-Modified Write Pseudocode (from AN1699)
+        * current_val = read_register(mmd, addr) // Read current register value
+        * new_val = current_val AND (NOT mask) // Clear bit fields to be written
+        * new_val = new_val OR value // Set bits
+        * write_register(mmd, addr, new_val) // Write back updated register value
+        */
+       for (int i = 0; i < ARRAY_SIZE(lan867x_fixup_registers); i++) {
+               reg = lan867x_fixup_registers[i];
+               reg_value = phy_read_mmd(phydev, MDIO_MMD_VEND2, reg);
+               reg_value &= ~lan867x_fixup_masks[i];
+               reg_value |= lan867x_fixup_values[i];
+               err = phy_write_mmd(phydev, MDIO_MMD_VEND2, reg, reg_value);
+               if (err != 0)
+                       return err;
+       }
+
+       /* None of the interrupts in the lan867x phy seem relevant.
+        * Other phys inspect the link status and call phy_trigger_machine
+        * in the interrupt handler.
+        * This phy does not support link status, and thus has no interrupt
+        * for it either.
+        * So we'll just disable all interrupts on the chip.
+        */
+       err = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_IRQ_1_CTL, 0xFFFF);
+       if (err != 0)
+               return err;
+       return phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_IRQ_2_CTL, 0xFFFF);
+}
+
+static int lan867x_read_status(struct phy_device *phydev)
+{
+       /* The phy has some limitations, namely:
+        *  - always reports link up
+        *  - only supports 10MBit half duplex
+        *  - does not support auto negotiate
+        */
+       phydev->link = 1;
+       phydev->duplex = DUPLEX_HALF;
+       phydev->speed = SPEED_10;
+       phydev->autoneg = AUTONEG_DISABLE;
+
+       return 0;
+}
+
+static struct phy_driver lan867x_driver[] = {
+       {
+               PHY_ID_MATCH_MODEL(PHY_ID_LAN867X),
+               .name               = "LAN867X",
+               .features           = PHY_BASIC_T1S_P2MP_FEATURES,
+               .config_init        = lan867x_config_init,
+               .read_status        = lan867x_read_status,
+               .get_plca_cfg       = genphy_c45_plca_get_cfg,
+               .set_plca_cfg       = genphy_c45_plca_set_cfg,
+               .get_plca_status    = genphy_c45_plca_get_status,
+       }
+};
+
+module_phy_driver(lan867x_driver);
+
+static struct mdio_device_id __maybe_unused tbl[] = {
+       { PHY_ID_MATCH_MODEL(PHY_ID_LAN867X) },
+       { }
+};
+
+MODULE_DEVICE_TABLE(mdio, tbl);
+
+MODULE_DESCRIPTION("Microchip 10BASE-T1S lan867x Phy driver");
+MODULE_AUTHOR("Ramón Nordin Rodriguez");
+MODULE_LICENSE("GPL");