arm64: dts: ti: k3-am68-sk-base-board: Add uart pinmux

Define the wakeup uart pin-mux for completeness and add explicit
muxing for mcu_uart0. This allows the device tree usage in bootloader
and firmwares that can configure the same appropriately.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 014ff13d103251233f683fe3f9f91326fed52e58..979898bc5b0233b6cbbd384a2ee9447aa944000c 100644 (file)
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -22,6 +22,8 @@
        };
 
        aliases {
+               serial0 = &wkup_uart0;
+               serial1 = &mcu_uart0;
                serial2 = &main_uart8;
                mmc1 = &main_sdhci1;
                can0 = &mcu_mcan0;
@@ -202,6 +204,15 @@
 };
 
 &wkup_pmx2 {
+       wkup_uart0_pins_default: wkup-uart0-pins-default {
+               pinctrl-single,pins = <
+                       J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (E25) WKUP_GPIO0_6.WKUP_UART0_CTSn */
+                       J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */
+                       J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
+                       J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
+               >;
+       };
+
        mcu_cpsw_pins_default: mcu-cpsw-pins-default {
                pinctrl-single,pins = <
                        J721S2_WKUP_IOPAD(0x02C, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
@@ -254,6 +265,13 @@
                >;
        };
 
+       mcu_uart0_pins_default: mcu-uart0-pins-default {
+               pinctrl-single,pins = <
+                       J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C24) WKUP_GPIO0_13.MCU_UART0_RXD */
+                       J721S2_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (C25) WKUP_GPIO0_12.MCU_UART0_TXD */
+               >;
+       };
+
        mcu_rpi_header_gpio0_pins0_default: mcu-rpi-header-gpio0-pins0-default {
                pinctrl-single,pins = <
                        J721S2_WKUP_IOPAD(0x118, PIN_INPUT, 7) /* (G25) WKUP_GPIO0_66 */
@@ -305,6 +323,14 @@
 
 &wkup_uart0 {
        status = "reserved";
+       pinctrl-names = "default";
+       pinctrl-0 = <&wkup_uart0_pins_default>;
+};
+
+&mcu_uart0 {
+       status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&mcu_uart0_pins_default>;
 };
 
 &main_uart8 {