S: Maintained
T: git git://git.pengutronix.de/git/imx/linux-2.6.git
F: arch/arm/mach-imx/
-F: arch/arm/plat-mxc/
F: arch/arm/configs/imx*_defconfig
ARM/FREESCALE IMX6
source "arch/arm/mach-mv78xx0/Kconfig"
-source "arch/arm/plat-mxc/Kconfig"
+source "arch/arm/mach-imx/Kconfig"
source "arch/arm/mach-mxs/Kconfig"
# Platform directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_MXC) += mxc
plat-$(CONFIG_ARCH_OMAP) += omap
plat-$(CONFIG_ARCH_S3C64XX) += samsung
plat-$(CONFIG_ARCH_ZYNQ) += versatile
+if ARCH_MXC
+
+config MXC_IRQ_PRIOR
+ bool "Use IRQ priority"
+ help
+ Select this if you want to use prioritized IRQ handling.
+ This feature prevents higher priority ISR to be interrupted
+ by lower priority IRQ even IRQF_DISABLED flag is not set.
+ This may be useful in embedded applications, where are strong
+ requirements for timing.
+ Say N here, unless you have a specialized requirement.
+
+config MXC_TZIC
+ bool
+
+config MXC_AVIC
+ bool
+
+config MXC_DEBUG_BOARD
+ bool "Enable MXC debug board(for 3-stack)"
+ help
+ The debug board is an integral part of the MXC 3-stack(PDK)
+ platforms, it can be attached or removed from the peripheral
+ board. On debug board, several debug devices(ethernet, UART,
+ buttons, LEDs and JTAG) are implemented. Between the MCU and
+ these devices, a CPLD is added as a bridge which performs
+ data/address de-multiplexing and decode, signal level shift,
+ interrupt control and various board functions.
+
+config HAVE_EPIT
+ bool
+
+config MXC_USE_EPIT
+ bool "Use EPIT instead of GPT"
+ depends on HAVE_EPIT
+ help
+ Use EPIT as the system timer on systems that have it. Normally you
+ don't have a reason to do so as the EPIT has the same features and
+ uses the same clocks as the GPT. Anyway, on some systems the GPT
+ may be in use for other purposes.
+
+config MXC_ULPI
+ bool
+
+config ARCH_HAS_RNGA
+ bool
+
+config IRAM_ALLOC
+ bool
+ select GENERIC_ALLOCATOR
+
config HAVE_IMX_GPC
bool
select PINCTRL_IMX51
select SOC_IMX5
+menu "Freescale MXC Implementations"
+
+choice
+ prompt "Freescale CPU family:"
+ default ARCH_IMX_V6_V7
+
+config ARCH_IMX_V4_V5
+ bool "i.MX1, i.MX21, i.MX25, i.MX27"
+ select ARM_PATCH_PHYS_VIRT
+ select AUTO_ZRELADDR if !ZBOOT_ROM
+ help
+ This enables support for systems based on the Freescale i.MX ARMv4
+ and ARMv5 SoCs
+
if ARCH_IMX_V4_V5
comment "MX1 platforms:"
endif
+config ARCH_IMX_V6_V7
+ bool "i.MX3, i.MX5, i.MX6"
+ select ARM_PATCH_PHYS_VIRT
+ select AUTO_ZRELADDR if !ZBOOT_ROM
+ select MIGHT_HAVE_CACHE_L2X0
+ help
+ This enables support for systems based on the Freescale i.MX3, i.MX5
+ and i.MX6 family.
+
if ARCH_IMX_V6_V7
comment "MX31 platforms:"
endif
+endchoice
+
+endmenu
+
source "arch/arm/mach-imx/devices/Kconfig"
+
+endif
+obj-y := time.o cpu.o system.o irq-common.o
+
obj-$(CONFIG_SOC_IMX1) += clk-imx1.o mm-imx1.o
obj-$(CONFIG_SOC_IMX21) += clk-imx21.o mm-imx21.o
obj-$(CONFIG_IMX_HAVE_IOMUX_V1) += iomux-v1.o
obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
+obj-$(CONFIG_MXC_TZIC) += tzic.o
+obj-$(CONFIG_MXC_AVIC) += avic.o
+
+obj-$(CONFIG_IRAM_ALLOC) += iram_alloc.o
+obj-$(CONFIG_MXC_ULPI) += ulpi.o
+obj-$(CONFIG_MXC_USE_EPIT) += epit.o
+obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
+obj-$(CONFIG_CPU_FREQ_IMX) += cpufreq.o
+obj-$(CONFIG_CPU_IDLE) += cpuidle.o
+
+ifdef CONFIG_SND_IMX_SOC
+obj-y += ssi-fiq.o
+obj-y += ssi-fiq-ksym.o
+endif
+
# Support for CMOS sensor interface
obj-$(CONFIG_MX1_VIDEO) += mx1-camera-fiq.o mx1-camera-fiq-ksym.o
+++ /dev/null
-if ARCH_MXC
-
-menu "Freescale MXC Implementations"
-
-choice
- prompt "Freescale CPU family:"
- default ARCH_IMX_V6_V7
-
-config ARCH_IMX_V4_V5
- bool "i.MX1, i.MX21, i.MX25, i.MX27"
- select ARM_PATCH_PHYS_VIRT
- select AUTO_ZRELADDR if !ZBOOT_ROM
- help
- This enables support for systems based on the Freescale i.MX ARMv4
- and ARMv5 SoCs
-
-config ARCH_IMX_V6_V7
- bool "i.MX3, i.MX5, i.MX6"
- select ARM_PATCH_PHYS_VIRT
- select AUTO_ZRELADDR if !ZBOOT_ROM
- select MIGHT_HAVE_CACHE_L2X0
- help
- This enables support for systems based on the Freescale i.MX3, i.MX5
- and i.MX6 family.
-
-endchoice
-
-source "arch/arm/mach-imx/Kconfig"
-
-endmenu
-
-config MXC_IRQ_PRIOR
- bool "Use IRQ priority"
- help
- Select this if you want to use prioritized IRQ handling.
- This feature prevents higher priority ISR to be interrupted
- by lower priority IRQ even IRQF_DISABLED flag is not set.
- This may be useful in embedded applications, where are strong
- requirements for timing.
- Say N here, unless you have a specialized requirement.
-
-config MXC_TZIC
- bool
-
-config MXC_AVIC
- bool
-
-config MXC_DEBUG_BOARD
- bool "Enable MXC debug board(for 3-stack)"
- help
- The debug board is an integral part of the MXC 3-stack(PDK)
- platforms, it can be attached or removed from the peripheral
- board. On debug board, several debug devices(ethernet, UART,
- buttons, LEDs and JTAG) are implemented. Between the MCU and
- these devices, a CPLD is added as a bridge which performs
- data/address de-multiplexing and decode, signal level shift,
- interrupt control and various board functions.
-
-config HAVE_EPIT
- bool
-
-config MXC_USE_EPIT
- bool "Use EPIT instead of GPT"
- depends on HAVE_EPIT
- help
- Use EPIT as the system timer on systems that have it. Normally you
- don't have a reason to do so as the EPIT has the same features and
- uses the same clocks as the GPT. Anyway, on some systems the GPT
- may be in use for other purposes.
-
-config MXC_ULPI
- bool
-
-config ARCH_HAS_RNGA
- bool
-
-config IRAM_ALLOC
- bool
- select GENERIC_ALLOCATOR
-
-endif
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-
-# Common support
-obj-y := time.o cpu.o system.o irq-common.o
-
-obj-$(CONFIG_MXC_TZIC) += tzic.o
-obj-$(CONFIG_MXC_AVIC) += avic.o
-
-obj-$(CONFIG_IRAM_ALLOC) += iram_alloc.o
-obj-$(CONFIG_MXC_ULPI) += ulpi.o
-obj-$(CONFIG_MXC_USE_EPIT) += epit.o
-obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
-obj-$(CONFIG_CPU_FREQ_IMX) += cpufreq.o
-obj-$(CONFIG_CPU_IDLE) += cpuidle.o
-ifdef CONFIG_SND_IMX_SOC
-obj-y += ssi-fiq.o
-obj-y += ssi-fiq-ksym.o
-endif
projects / users / hch / dma-mapping.git / commitdiff