/* Pointer to debug logging header */
u32 hi_dbglog_hdr; /* 0x08 */
- /* Indicates whether or not flash is present on Target.
- * NB: flash_is_present indicator is here not just
- * because it might be of interest to the Host; but
- * also because it's set early on by Target's startup
- * asm code and we need it to have a special RAM address
- * so that it doesn't get reinitialized with the rest
- * of data.
- */
- u32 hi_flash_is_present; /* 0x0c */
+ u32 hi_unused1; /* 0x0c */
/*
* General-purpose flag bits, similar to AR6000_OPTION_* flags.
*/
u32 hi_serial_enable; /* 0x14 */
- /* Start address of Flash DataSet index, if any */
+ /* Start address of DataSet index, if any */
u32 hi_dset_list_head; /* 0x18 */
/* Override Target application start address */
u32 hi_hci_uart_support_pins; /* 0xa4 */
/* NOTE: byte [0] = RESET pin (bit 7 is polarity), bytes[1]..bytes[3] are for future use */
u32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */
- /* 0xa8 - [0]: 1 = enable, 0 = disable
- * [1]: 0 = UART FC active low, 1 = UART FC active high
- * 0xa9 - [7:0]: wakeup timeout in ms
- * 0xaa, 0xab - [15:0]: idle timeout in ms
- */
- /* Pointer to extended board Data */
- u32 hi_board_ext_data; /* 0xac */
- u32 hi_board_ext_data_initialized; /* 0xb0 */
+ /*
+ * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
+ * [31:16]: wakeup timeout in ms
+ */
+
+ /* Pointer to extended board data */
+ u32 hi_board_ext_data; /* 0xac */
+ u32 hi_board_ext_data_config; /* 0xb0 */
+
+ /*
+ * Bit [0] : valid
+ * Bit[31:16: size
+ */
+ /*
+ * hi_reset_flag is used to do some stuff when target reset.
+ * such as restore app_start after warm reset or
+ * preserve host Interest area, or preserve ROM data, literals etc.
+ */
+ u32 hi_reset_flag; /* 0xb4 */
+ /* indicate hi_reset_flag is valid */
+ u32 hi_reset_flag_valid; /* 0xb8 */
+ u32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */
+ /*
+ * 0xbc - [31:0]: idle timeout in ms
+ */
+ /* ACS flags */
+ u32 hi_acs_flags; /* 0xc0 */
+ u32 hi_console_flags; /* 0xc4 */
+ u32 hi_nvram_state; /* 0xc8 */
+ u32 hi_option_flag2; /* 0xcc */
+
+ /* If non-zero, override values sent to Host in WMI_READY event. */
+ u32 hi_sw_version_override; /* 0xd0 */
+ u32 hi_abi_version_override; /* 0xd4 */
+
+ /*
+ * Percentage of high priority RX traffic to total expected RX traffic -
+ * applicable only to ar6004
+ */
+ u32 hi_hp_rx_traffic_ratio; /* 0xd8 */
+
+ /* test applications flags */
+ u32 hi_test_apps_related ; /* 0xdc */
+ /* location of test script */
+ u32 hi_ota_testscript; /* 0xe0 */
+ /* location of CAL data */
+ u32 hi_cal_data; /* 0xe4 */
+ /* Number of packet log buffers */
+ u32 hi_pktlog_num_buffers; /* 0xe8 */
+
} POSTPACK;
/* Bits defined in hi_option_flag */
#define HI_OPTION_TIMER_WAR 0x01 /* Enable timer workaround */
#define HI_OPTION_BMI_CRED_LIMIT 0x02 /* Limit BMI command credits */
#define HI_OPTION_RELAY_DOT11_HDR 0x04 /* Relay Dot11 hdr to/from host */
-#define HI_OPTION_FW_MODE_LSB 0x08 /* low bit of MODE (see below) */
-#define HI_OPTION_FW_MODE_MSB 0x10 /* high bit of MODE (see below) */
-#define HI_OPTION_ENABLE_PROFILE 0x20 /* Enable CPU profiling */
-#define HI_OPTION_DISABLE_DBGLOG 0x40 /* Disable debug logging */
-#define HI_OPTION_SKIP_ERA_TRACKING 0x80 /* Skip Era Tracking */
-#define HI_OPTION_PAPRD_DISABLE 0x100 /* Disable PAPRD (debug) */
+/* MAC addr method 0-locally administred 1-globally unique addrs */
+#define HI_OPTION_MAC_ADDR_METHOD 0x08
+#define HI_OPTION_FW_BRIDGE 0x10 /* Firmware Bridging */
+#define HI_OPTION_ENABLE_PROFILE 0x20 /* Enable CPU profiling */
+#define HI_OPTION_DISABLE_DBGLOG 0x40 /* Disable debug logging */
+#define HI_OPTION_SKIP_ERA_TRACKING 0x80 /* Skip Era Tracking */
+#define HI_OPTION_PAPRD_DISABLE 0x100 /* Disable PAPRD (debug) */
+#define HI_OPTION_NUM_DEV_LSB 0x200
+#define HI_OPTION_NUM_DEV_MSB 0x800
+#define HI_OPTION_DEV_MODE_LSB 0x1000
+#define HI_OPTION_DEV_MODE_MSB 0x8000000
+/* Disable LowFreq Timer Stabilization */
+#define HI_OPTION_NO_LFT_STBL 0x10000000
+#define HI_OPTION_SKIP_REG_SCAN 0x20000000 /* Skip regulatory scan */
+/* Do regulatory scan during init beforesending WMI ready event to host */
+#define HI_OPTION_INIT_REG_SCAN 0x40000000
+#define HI_OPTION_SKIP_MEMMAP 0x80000000 /* REV6: Do not adjust memory
+ map */
+
+/* hi_option_flag2 options */
+#define HI_OPTION_OFFLOAD_AMSDU 0x01
+#define HI_OPTION_DFS_SUPPORT 0x02 /* Enable DFS support */
+
+#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
/* 2 bits of hi_option_flag are used to represent 3 modes */
#define HI_OPTION_FW_MODE_IBSS 0x0 /* IBSS Mode */
#define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
#define HI_OPTION_FW_MODE_AP 0x2 /* AP Mode */
-/* Fw Mode Mask */
-#define HI_OPTION_FW_MODE_MASK 0x3
-#define HI_OPTION_FW_MODE_SHIFT 0x3
+/* 2 bits of hi_option flag are usedto represent 4 submodes */
+#define HI_OPTION_FW_SUBMODE_NONE 0x0 /* Normal mode */
+#define HI_OPTION_FW_SUBMODE_P2PDEV 0x1 /* p2p device mode */
+#define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
+#define HI_OPTION_FW_SUBMODE_P2PGO 0x3 /* p2p go mode */
+
+/* Num dev Mask */
+#define HI_OPTION_NUM_DEV_MASK 0x7
+#define HI_OPTION_NUM_DEV_SHIFT 0x9
+
+/* firmware bridging */
+#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
+
+/* Fw Mode/SubMode Mask
+|------------------------------------------------------------------------------|
+| SUB | SUB | SUB | SUB | | | |
+| MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0|
+| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2)
+|------------------------------------------------------------------------------|
+*/
+#define HI_OPTION_FW_MODE_BITS 0x2
+#define HI_OPTION_FW_MODE_MASK 0x3
+#define HI_OPTION_FW_MODE_SHIFT 0xC
+#define HI_OPTION_ALL_FW_MODE_MASK 0xFF
+
+#define HI_OPTION_FW_SUBMODE_BITS 0x2
+#define HI_OPTION_FW_SUBMODE_MASK 0x3
+#define HI_OPTION_FW_SUBMODE_SHIFT 0x14
+#define HI_OPTION_ALL_FW_SUBMODE_MASK 0xFF00
+#define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
+
+/* hi_reset_flag */
+
+/* preserve App Start address */
+#define HI_RESET_FLAG_PRESERVE_APP_START 0x01
+/* preserve host interest */
+#define HI_RESET_FLAG_PRESERVE_HOST_INTEREST 0x02
+#define HI_RESET_FLAG_PRESERVE_ROMDATA 0x04 /* preserve ROM data */
+#define HI_RESET_FLAG_PRESERVE_NVRAM_STATE 0x08
+#define HI_RESET_FLAG_PRESERVE_BOOT_INFO 0x10
+
+#define HI_RESET_FLAG_IS_VALID 0x12345678 /* indicate the reset flag is
+valid */
+
+#define ON_RESET_FLAGS_VALID() \
+ (HOST_INTEREST->hi_reset_flag_valid == HI_RESET_FLAG_IS_VALID)
+
+#define RESET_FLAGS_VALIDATE() \
+ (HOST_INTEREST->hi_reset_flag_valid = HI_RESET_FLAG_IS_VALID)
+
+#define RESET_FLAGS_INVALIDATE() \
+ (HOST_INTEREST->hi_reset_flag_valid = 0)
+
+#define ON_RESET_PRESERVE_APP_START() \
+ (HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_APP_START)
+
+#define ON_RESET_PRESERVE_NVRAM_STATE() \
+ (HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_NVRAM_STATE)
+
+#define ON_RESET_PRESERVE_HOST_INTEREST() \
+ (HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_HOST_INTEREST)
+
+#define ON_RESET_PRESERVE_ROMDATA() \
+ (HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_ROMDATA)
+
+#define ON_RESET_PRESERVE_BOOT_INFO() \
+ (HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_BOOT_INFO)
+
+#define HI_ACS_FLAGS_ENABLED (1 << 0) /* ACS is enabled */
+#define HI_ACS_FLAGS_USE_WWAN (1 << 1) /* Use physical WWAN device */
+#define HI_ACS_FLAGS_TEST_VAP (1 << 2) /* Use test VAP */
+
+/* CONSOLE FLAGS
+ *
+ * Bit Range Meaning
+ * --------- --------------------------------
+ * 2..0 UART ID (0 = Default)
+ * 3 Baud Select (0 = 9600, 1 = 115200)
+ * 30..4 Reserved
+ * 31 Enable Console
+ *
+ */
+
+#define HI_CONSOLE_FLAGS_ENABLE (1 << 31)
+#define HI_CONSOLE_FLAGS_UART_MASK (0x7)
+#define HI_CONSOLE_FLAGS_UART_SHIFT 0
+#define HI_CONSOLE_FLAGS_BAUD_SELECT (1 << 3)
/*
* Intended for use by Host software, this macro returns the Target RAM
#define AR6003_HOST_INTEREST_ITEM_ADDRESS(item) \
(u32)((unsigned long)&((((struct host_interest_s *)(AR6003_HOST_INTEREST_ADDRESS))->item)))
+#define AR6004_HOST_INTEREST_ITEM_ADDRESS(item) \
+ ((A_UINT32)&((((struct host_interest_s *)(AR6004_HOST_INTEREST_ADDRESS))->item)))
+
+
#define HOST_INTEREST_DBGLOG_IS_ENABLED() \
(!(HOST_INTEREST->hi_option_flag & HI_OPTION_DISABLE_DBGLOG))
+#define HOST_INTEREST_PKTLOG_IS_ENABLED() \
+ ((HOST_INTEREST->hi_pktlog_num_buffers))
+
+
#define HOST_INTEREST_PROFILE_IS_ENABLED() \
(HOST_INTEREST->hi_option_flag & HI_OPTION_ENABLE_PROFILE)
+#define LF_TIMER_STABILIZATION_IS_ENABLED() \
+ (!(HOST_INTEREST->hi_option_flag & HI_OPTION_NO_LFT_STBL))
+
+#define IS_AMSDU_OFFLAOD_ENABLED() \
+ ((HOST_INTEREST->hi_option_flag2 & HI_OPTION_OFFLOAD_AMSDU))
+
+#define HOST_INTEREST_DFS_IS_ENABLED() \
+ ((HOST_INTEREST->hi_option_flag2 & HI_OPTION_DFS_SUPPORT))
+
/* Convert a Target virtual address into a Target physical address */
#define AR6002_VTOP(vaddr) ((vaddr) & 0x001fffff)
#define AR6003_VTOP(vaddr) ((vaddr) & 0x001fffff)
#define TARG_VTOP(TargetType, vaddr) \
(((TargetType) == TARGET_TYPE_AR6002) ? AR6002_VTOP(vaddr) : AR6003_VTOP(vaddr))
-/* override REV2 ROM's app start address */
-#define AR6002_REV2_APP_START_OVERRIDE 0x911A00
-#define AR6003_REV1_APP_START_OVERRIDE 0x944c00
-#define AR6003_REV1_OTP_DATA_ADDRESS 0x542800
-#define AR6003_REV2_APP_START_OVERRIDE 0x945000
-#define AR6003_REV2_OTP_DATA_ADDRESS 0x543800
-#define AR6003_BOARD_EXT_DATA_ADDRESS 0x57E600
+#define AR6003_REV2_APP_START_OVERRIDE 0x944C00
+#define AR6003_REV2_APP_LOAD_ADDRESS 0x543180
+#define AR6003_REV2_BOARD_EXT_DATA_ADDRESS 0x57E500
+#define AR6003_REV2_DATASET_PATCH_ADDRESS 0x57e884
+#define AR6003_REV2_RAM_RESERVE_SIZE 6912
+
+#define AR6003_REV3_APP_START_OVERRIDE 0x945d00
+#define AR6003_REV3_APP_LOAD_ADDRESS 0x545000
+#define AR6003_REV3_BOARD_EXT_DATA_ADDRESS 0x542330
+#define AR6003_REV3_DATASET_PATCH_ADDRESS 0x57FF74
+#define AR6003_REV3_RAM_RESERVE_SIZE 512
+#define AR6003_BOARD_EXT_DATA_ADDRESS 0x57E600
/* # of u32 entries in targregs, used by DIAG_FETCH_TARG_REGS */
#define AR6003_FETCH_TARG_REGS_COUNT 64
unsigned int enableuartprint = ENABLEUARTPRINT_DEFAULT;
unsigned int logWmiRawMsgs = 0;
unsigned int enabletimerwar = 0;
+unsigned int num_device = 1;
+unsigned int regscanmode;
unsigned int fwmode = 1;
unsigned int mbox_yield_limit = 99;
unsigned int enablerssicompensation = 0;
unsigned int csumOffload=0;
unsigned int csumOffloadTest=0;
unsigned int eppingtest=0;
+unsigned int mac_addr_method;
+unsigned int firmware_bridge;
module_param_string(ifname, ifname, sizeof(ifname), 0644);
module_param(wlaninitmode, int, 0644);
filename = AR6003_REV1_OTP_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_OTP_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_OTP_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown firmware revision: %d\n", ar->arVersion.target_ver));
return A_ERROR;
filename = AR6003_REV1_FIRMWARE_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_FIRMWARE_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_FIRMWARE_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown firmware revision: %d\n", ar->arVersion.target_ver));
return A_ERROR;
filename = AR6003_REV1_EPPING_FIRMWARE_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_EPPING_FIRMWARE_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_EPPING_FIRMWARE_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("eppingtest : unsupported firmware revision: %d\n",
ar->arVersion.target_ver));
filename = AR6003_REV1_TCMD_FIRMWARE_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_TCMD_FIRMWARE_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_TCMD_FIRMWARE_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown firmware revision: %d\n", ar->arVersion.target_ver));
return A_ERROR;
filename = AR6003_REV1_PATCH_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_PATCH_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_PATCH_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown firmware revision: %d\n", ar->arVersion.target_ver));
return A_ERROR;
filename = AR6003_REV1_BOARD_DATA_FILE;
} else if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
filename = AR6003_REV2_BOARD_DATA_FILE;
+ } else if (ar->arVersion.target_ver == AR6003_REV3_VERSION) {
+ filename = AR6003_REV3_BOARD_DATA_FILE;
} else {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown firmware revision: %d\n", ar->arVersion.target_ver));
return A_ERROR;
}
/* Record the fact that extended board Data IS initialized */
- param = 1;
- bmifn(BMIWriteMemory(ar->arHifDevice, HOST_INTEREST_ITEM_ADDRESS(ar, hi_board_ext_data_initialized), (u8 *)¶m, 4));
+ param = (board_ext_data_size << 16) | 1;
+ bmifn(BMIWriteMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar, hi_board_ext_data_config),
+ (unsigned char *)¶m, 4));
}
fw_entry_size = board_data_size;
}
bmifn(BMIWriteMemory(ar->arHifDevice, HOST_INTEREST_ITEM_ADDRESS(ar, hi_board_data_initialized), (u8 *)¶m, 4));
/* Transfer One time Programmable data */
- AR6K_DATA_DOWNLOAD_ADDRESS(address, ar->arVersion.target_ver);
+ AR6K_APP_LOAD_ADDRESS(address, ar->arVersion.target_ver);
+ if (ar->arVersion.target_ver == AR6003_REV3_VERSION)
+ address = 0x1234;
status = ar6000_transfer_bin_file(ar, AR6K_OTP_FILE, address, true);
if (status == 0) {
/* Execute the OTP code */
}
/* Download Target firmware */
- AR6K_DATA_DOWNLOAD_ADDRESS(address, ar->arVersion.target_ver);
+ AR6K_APP_LOAD_ADDRESS(address, ar->arVersion.target_ver);
+ if (ar->arVersion.target_ver == AR6003_REV3_VERSION)
+ address = 0x1234;
if ((ar6000_transfer_bin_file(ar, AR6K_FIRMWARE_FILE, address, true)) != 0) {
return A_ERROR;
}
AR6K_APP_START_OVERRIDE_ADDRESS(address, ar->arVersion.target_ver);
bmifn(BMISetAppStart(ar->arHifDevice, address));
- /* Apply the patches */
- AR6K_PATCH_DOWNLOAD_ADDRESS(address, ar->arVersion.target_ver);
- if ((ar6000_transfer_bin_file(ar, AR6K_PATCH_FILE, address, false)) != 0) {
- return A_ERROR;
- }
-
- param = address;
- bmifn(BMIWriteMemory(ar->arHifDevice, HOST_INTEREST_ITEM_ADDRESS(ar, hi_dset_list_head), (u8 *)¶m, 4));
-
- if (ar->arTargetType == TARGET_TYPE_AR6003) {
- if (ar->arVersion.target_ver == AR6003_REV1_VERSION) {
- /* Reserve 5.5K of RAM */
- param = 5632;
- } else { /* AR6003_REV2_VERSION */
- /* Reserve 6.5K of RAM */
- param = 6656;
- }
- bmifn(BMIWriteMemory(ar->arHifDevice, HOST_INTEREST_ITEM_ADDRESS(ar, hi_end_RAM_reserve_sz), (u8 *)¶m, 4));
- }
+ if(ar->arTargetType == TARGET_TYPE_AR6003) {
+ AR6K_DATASET_PATCH_ADDRESS(address, ar->arVersion.target_ver);
+ if ((ar6000_transfer_bin_file(ar, AR6K_PATCH_FILE,
+ address, false)) != 0)
+ return A_ERROR;
+ param = address;
+ bmifn(BMIWriteMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar, hi_dset_list_head),
+ (unsigned char *)¶m, 4));
+ }
/* Restore system sleep */
address = RTC_BASE_ADDRESS + SYSTEM_SLEEP_ADDRESS;
return A_ERROR;
}
+ param |= (num_device << HI_OPTION_NUM_DEV_SHIFT);
param |= (fwmode << HI_OPTION_FW_MODE_SHIFT);
+ param |= (mac_addr_method << HI_OPTION_MAC_ADDR_METHOD_SHIFT);
+ param |= (firmware_bridge << HI_OPTION_FW_BRIDGE_SHIFT);
+
if (BMIWriteMemory(ar->arHifDevice,
HOST_INTEREST_ITEM_ADDRESS(ar, hi_option_flag),
* It is difficult to patch the firmware boot code,
* but possible in theory.
*/
- if (ar->arTargetType == TARGET_TYPE_AR6003) {
- param = AR6003_BOARD_EXT_DATA_ADDRESS;
- if (BMIWriteMemory(ar->arHifDevice,
- HOST_INTEREST_ITEM_ADDRESS(ar, hi_board_ext_data),
- (u8 *)¶m,
- 4) != 0)
- {
- AR_DEBUG_PRINTF(ATH_DEBUG_ERR,("BMIWriteMemory for hi_board_ext_data failed \n"));
- return A_ERROR;
- }
- }
+ if (ar->arTargetType == TARGET_TYPE_AR6003) {
+ A_UINT32 ramReservedSz;
+ if (ar->arVersion.target_ver == AR6003_REV2_VERSION) {
+ param = AR6003_REV2_BOARD_EXT_DATA_ADDRESS;
+ ramReservedSz = AR6003_REV2_RAM_RESERVE_SIZE;
+ } else {
+ param = AR6003_REV3_BOARD_EXT_DATA_ADDRESS;
+ ramReservedSz = AR6003_REV3_RAM_RESERVE_SIZE;
+ }
+ if (BMIWriteMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar, hi_board_ext_data),
+ (u8 *)¶m, 4) != 0) {
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR,
+ ("BMIWriteMemory for "
+ "hi_board_ext_data failed\n"));
+ return A_ERROR;
+ }
+ if (BMIWriteMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar,
+ hi_end_RAM_reserve_sz),
+ (u8 *)&ramReservedSz, 4) != 0) {
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR ,
+ ("BMIWriteMemory for "
+ "hi_end_RAM_reserve_sz failed\n"));
+ return A_ERROR;
+ }
+ }
/* since BMIInit is called in the driver layer, we have to set the block
* size here for the target */
goto ar6000_init_done;
}
+ if (regscanmode) {
+ A_UINT32 param;
+
+ if (BMIReadMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar,
+ hi_option_flag),
+ (u8 *)¶m,
+ 4) != 0) {
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR,
+ ("BMIReadMemory forsetting "
+ "regscanmode failed\n"));
+ return A_ERROR;
+ }
+
+ if (regscanmode == 1)
+ param |= HI_OPTION_SKIP_REG_SCAN;
+ else if (regscanmode == 2)
+ param |= HI_OPTION_INIT_REG_SCAN;
+
+ if (BMIWriteMemory(ar->arHifDevice,
+ HOST_INTEREST_ITEM_ADDRESS(ar,
+ hi_option_flag),
+ (u8 *)¶m,
+ 4) != 0) {
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR,
+ ("BMIWriteMemory forsetting "
+ "regscanmode failed\n"));
+ return A_ERROR;
+ }
+ AR_DEBUG_PRINTF(ATH_DEBUG_INFO, ("Regulatory scan mode set\n"));
+ }
+
/*
* give our connected endpoints some buffers
*/
} \
} while (0)
+#define AR6K_DATASET_PATCH_ADDRESS(_param, _ver) do { \
+ if ((_ver) == AR6003_REV2_VERSION) { \
+ (_param) = AR6003_REV2_DATASET_PATCH_ADDRESS; \
+ } else if ((_ver) == AR6003_REV3_VERSION) { \
+ (_param) = AR6003_REV3_DATASET_PATCH_ADDRESS; \
+ } else { \
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown Version: %d\n", _ver)); \
+ A_ASSERT(0); \
+ } \
+} while (0)
+
+#define AR6K_APP_LOAD_ADDRESS(_param, _ver) do { \
+ if ((_ver) == AR6003_REV2_VERSION) { \
+ (_param) = AR6003_REV2_APP_LOAD_ADDRESS; \
+ } else if ((_ver) == AR6003_REV3_VERSION) { \
+ (_param) = AR6003_REV3_APP_LOAD_ADDRESS; \
+ } else { \
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown Version: %d\n", _ver)); \
+ A_ASSERT(0); \
+ } \
+} while (0)
+
#define AR6K_APP_START_OVERRIDE_ADDRESS(_param, _ver) do { \
- if ((_ver) == AR6003_REV1_VERSION) { \
- (_param) = AR6003_REV1_APP_START_OVERRIDE; \
- } else if ((_ver) == AR6003_REV2_VERSION) { \
- (_param) = AR6003_REV2_APP_START_OVERRIDE; \
- } else { \
- AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown Version: %d\n", _ver)); \
- A_ASSERT(0); \
- } \
+ if ((_ver) == AR6003_REV2_VERSION) { \
+ (_param) = AR6003_REV2_APP_START_OVERRIDE; \
+ } else if ((_ver) == AR6003_REV3_VERSION) { \
+ (_param) = AR6003_REV3_APP_START_OVERRIDE; \
+ } else { \
+ AR_DEBUG_PRINTF(ATH_DEBUG_ERR, ("Unknown Version: %d\n", _ver)); \
+ A_ASSERT(0); \
+ } \
} while (0)
/* AR6003 1.0 definitions */
#define AR6003_REV2_BOARD_DATA_FILE "ath6k/AR6003/hw2.0/bdata.CUSTOM.bin"
#endif /* Board Data File */
+/* AR6003 3.0 definitions */
+#define AR6003_REV3_VERSION 0x30000582
+#define AR6003_REV3_OTP_FILE "ath6k/AR6003/hw2.1.1/otp.bin"
+#define AR6003_REV3_FIRMWARE_FILE "ath6k/AR6003/hw2.1.1/athwlan.bin"
+#define AR6003_REV3_TCMD_FIRMWARE_FILE "ath6k/AR6003/hw2.1.1/athtcmd_ram.bin"
+#define AR6003_REV3_ART_FIRMWARE_FILE "ath6k/AR6003/hw2.1.1/device.bin"
+#define AR6003_REV3_PATCH_FILE "ath6k/AR6003/hw2.1.1/data.patch.bin"
+#define AR6003_REV3_EPPING_FIRMWARE_FILE "ath6k/AR6003/hw2.1.1/endpointping.bin"
+#ifdef CONFIG_AR600x_SD31_XXX
+#define AR6003_REV3_BOARD_DATA_FILE "ath6k/AR6003/hw2.1.1/bdata.SD31.bin"
+#elif defined(CONFIG_AR600x_SD32_XXX)
+#define AR6003_REV3_BOARD_DATA_FILE "ath6k/AR6003/hw2.1.1/bdata.SD32.bin"
+#elif defined(CONFIG_AR600x_WB31_XXX)
+#define AR6003_REV3_BOARD_DATA_FILE "ath6k/AR6003/hw2.1.1/bdata.WB31.bin"
+#else
+#define AR6003_REV3_BOARD_DATA_FILE "ath6k/AR6003/hw2.1.1/bdata.CUSTOM.bin"
+#endif /* Board Data File */
+
+
/* Power states */
enum {
WLAN_PWR_CTRL_UP = 0,
projects / users / hch / block.git / commitdiff